(Update TODO: check on how the Efficiency cores on Alder Lake (Gracemont) run inc reg. If it hurts throughput there, might be worth spending the extra code byte. They're derived from Silvermont, but much wider, although the wide back-end might mean the extra uop doesn't hurt even if there is one. With its L1i marking instruction boundaries, saving code-size might not be as big a deal for it.)
TL:DR/advice for modern CPUs: Use inc except with a memory destination. In code you're tuning to run on mainstream Intel or any AMD, inc register is fine. (e.g. like gcc -mtune=core2, -mtune=haswell, or -mtune=znver1). inc mem costs an extra uop vs. add on Intel P6 / SnB-family; the load can't micro-fuse.
If you care about Silvermont-family (including KNL in Xeon Phi, and some netbooks, chromebooks, and NAS servers), probably avoid inc. add 1 only costs 1 extra byte in 64-bit code, or 2 in 32-bit code. But it's not a performance disaster (just locally 1 extra ALU port used, not creating false dependencies or big stalls), so if you don't care much about SMont then don't worry about it.
Writing CF instead of leaving it unmodified can potentially be useful with other surrounding code that might benefit from CF dep-breaking, e.g. shifts. See below.
If you want to inc/dec without touching any flags, lea eax, [rax+1] runs efficiently and has the same code-size as add eax, 1. (Usually on fewer possible execution ports than add/inc, though, so add/inc are better when destroying FLAGS is not a problem. https://agner.org/optimize/)
On modern CPUs, add is never slower than inc (except for indirect code-size / decode effects), but usually it's not faster either, so you should prefer inc for code-size reasons. Especially if this choice is repeated many times in the same binary (e.g. if you are a compiler-writer).
inc saves 1 byte (64-bit mode), or 2 bytes (opcodes 0x40..F inc r32/dec r32 short form in 32-bit mode, re-purposed as the REX prefix for x86-64). This makes a small percentage difference in total code size. This helps instruction-cache hit rates, iTLB hit rate, and number of pages that have to be loaded from disk.
Advantages of inc:
- code-size directly
- Not using an immediate can have uop-cache effects on Sandybridge-family, which could offset the better micro-fusion of
add. (See Agner Fog's table 9.1 in the Sandybridge section of his microarch guide.) Perf counters can easily measure issue-stage uops, but it's harder to measure how things pack into the uop cache and uop-cache read bandwidth effects.
- Leaving CF unmodified is an advantage in some cases, on CPUs where you can read CF after
inc without a stall. (Not on Nehalem and earlier.)
There is one exception among modern CPUs: Silvermont/Goldmont/Knight's Landing decodes inc/dec efficiently as 1 uop, but expands to 2 in the allocate/rename (aka issue) stage. The extra uop merges partial flags. inc throughput is only 1 per clock, vs. 0.5c (or 0.33c Goldmont) for independent add r32, imm8 because of the dep chain created by the flag-merging uops.
Unlike P4, the register result doesn't have a false-dep on flags (see below), so out-of-order execution takes the flag-merging off the latency critical path when nothing uses the flag result. (But the OOO window is much smaller than mainstream CPUs like Haswell or Ryzen.) Running inc as 2 separate uops is probably a win for Silvermont in most cases; most x86 instructions write all the flags without reading them, breaking these flag dependency chains.
SMont/KNL has a queue between decode and allocate/rename (See Intel's optimization manual, figure 16-2) so expanding to 2 uops during issue can fill bubbles from decode stalls (on instructions like one-operand mul, or pshufb, which produce more than 1 uop from the decoder and cause a 3-7 cycle stall for microcode). Or on Silvermont, just an instruction with more than 3 prefixes (including escape bytes and mandatory prefixes), e.g. REX + any SSSE3 or SSE4 instruction. But note that there is a ~28 uop loop buffer, so small loops don't suffer from these decode stalls.
inc/dec aren't the only instructions that decode as 1 but issue as 2: push/pop, call/ret, and lea with 3 components do this too. So do KNL's AVX512 gather instructions. Source: Intel's optimization manual, 17.1.2 Out-of-Order Engine (KNL). It's only a small throughput penalty (and sometimes not even that if anything else is a bigger bottleneck), so it's generally fine to still use inc for "generic" tuning.
Intel's optimization manual still recommends add 1 over inc in general, to avoid risks of partial-flag stalls. But since Intel's compiler doesn't do that by default, it's not too likely that future CPUs will make inc slow in all cases, like P4 did.
Clang 5.0 and Intel's ICC 17 (on Godbolt) do use inc when optimizing for speed (-O3), not just for size. -mtune=pentium4 makes them avoid inc/dec, but the default -mtune=generic doesn't put much weight on P4.
ICC17 -xMIC-AVX512 (equivalent to gcc's -march=knl) does avoid inc, which is probably a good bet in general for Silvermont / KNL. But it's not usually a performance disaster to use inc, so it's probably still appropriate for "generic" tuning to use inc/dec in most code, especially when the flag result isn't part of the critical path.
Other than Silvermont, this is mostly-stale optimization advice left over from Pentium4. On modern CPUs, there's only a problem if you actually read a flag that wasn't written by the last insn that wrote any flags. e.g. in BigInteger adc loops. (And in that case, you need to preserve CF so using add would break your code.)
add writes all the condition-flag bits in the EFLAGS register. Register-renaming makes write-only easy for out-of-order execution: see write-after-write and write-after-read hazards. add eax, 1 and add ecx, 1 can execute in parallel because they are fully independent of each other. (Even Pentium4 renames the condition flag bits separate from the rest of EFLAGS, since even add leaves the interrupts-enabled and many other bits unmodified.)
On P4, inc and dec depend on the previous value of the all the flags, so they can't execute in parallel with each other or preceding flag-setting instructions. (e.g. add eax, [mem] / inc ecx makes the inc wait until after the add, even if the add's load misses in cache.) This is called a false dependency. Partial-flag writes work by reading the old value of the flags, updating the bits other than CF, then writing the full flags.
All other out-of-order x86 CPUs (including AMD's), rename different parts of flags separately, so internally they do a write-only update to all the flags except CF. (source: Agner Fog's microarchitecture guide). Only a few instructions, like adc or cmc, truly read and then write flags. But also shl r, cl (see below).
Cases where add dest, 1 is preferable to inc dest, at least for Intel P6/SnB uarch families:
But beware of uop-cache effects with add [label], 1 which needs a 3
