assembly - Does it make any sense to use the LFENCE instruction on x86/x86_64 processors?

Question

Often in internet I find that LFENCE makes no sense in processors x86, ie it does nothing , so instead MFENCE we can absolutely painless to use SFENCE, because MFENCE = SFENCE + LFENCE = SFENCE + NOP = SFENCE.

But if LFENCE does not make sense, then why we have four approaches to make Sequential Consistency in x86/x86_64:

1. LOAD (without fence) and STORE + MFENCE
2. LOAD (without fence) and LOCK XCHG
3. MFENCE + LOAD and STORE (without fence)
4. LOCK XADD ( 0 ) and STORE (without fence)

Taken from here: http://www.cl.cam.ac.uk/~pes20/cpp/cpp0xmappings.html

As well as performances from Herb Sutter on page 34 at the bottom: https://skydrive.live.com/view.aspx?resid=4E86B0CF20EF15AD!24884&app=WordPdf&wdo=2&authkey=!AMtj_EflYn2507c

If LFENCE did not do anything, then the approach (3) would have the following meanings: SFENCE + LOAD and STORE (without fence), but there is no point in doing SFENCE before LOAD. Ie if LFENCE does nothing , the approach (3) does not make sense.

Does it make any sense instruction LFENCE in processors x86/x86_64?

ANSWER:

1. LFENCE required in cases which described in the accepted answer, below.

2. The approach (3) should be viewed not independently, but in combination with the previous commands. For example, approach (3):

MFENCE
MOV reg, [addr1]  // LOAD-1
MOV [addr2], reg  //STORE-1

MFENCE
MOV reg, [addr1]  // LOAD-2
MOV [addr2], reg  //STORE-2

We can rewrite the code of approach (3) as follows:

SFENCE
MOV reg, [addr1]  // LOAD-1
MOV [addr2], reg  //STORE-1

SFENCE
MOV reg, [addr1]  // LOAD-2
MOV [addr2], reg  //STORE-2

And here SFENCE makes sense to prevent reordering STORE-1 and LOAD-2. For this after STORE-1 command SFENCE flushes Store-Buffer.

Answer 1

Bottom line (TL;DR): LFENCE alone indeed seems useless for memory ordering, however it does not make SFENCE a substitute for MFENCE. The "arithmetic" logic in the question is not applicable.

---

Here is an excerpt from Intel's Software Developers Manual, volume 3, section 8.2.2 (the edition 325384-052US of September 2014), the same that I used in another answer

• Reads are not reordered with other reads.
• Writes are not reordered with older reads.
• Writes to memory are not reordered with other writes, with the following exceptions:
  • writes executed with the CLFLUSH instruction;
  • streaming stores (writes) executed with the non-temporal move instructions (MOVNTI, MOVNTQ, MOVNTDQ, MOVNTPS, and MOVNTPD); and
  • string operations (see Section 8.2.4.1).
• Reads may be reordered with older writes to different locations but not with older writes to the same location.
• Reads or writes cannot be reordered with I/O instructions, locked instructions, or serializing instructions.
• Reads cannot pass earlier LFENCE and MFENCE instructions.
• Writes cannot pass earlier LFENCE, SFENCE, and MFENCE instructions.
• LFENCE instructions cannot pass earlier reads.
• SFENCE instructions cannot pass earlier writes.
• MFENCE instructions cannot pass earlier reads or writes.

From here, it follows that:

• MFENCE is a full memory fence for all operations on all memory types, whether non-temporal or not.
• SFENCE only prevents reordering of writes (in other terminology, it's a StoreStore barrier), and is only useful together with non-temporal stores and other instructions listed as exceptions.
• LFENCE prevents reordering of reads with subsequent reads and writes (i.e. it combines LoadLoad and LoadStore barriers). However, the first two bullets say that LoadLoad and LoadStore barriers are always in place, no exceptions. Therefore LFENCE alone is useless for memory ordering.

To support the last claim, I looked at all places where LFENCE is mentioned in all 3 volumes of Intel's manual, and found none which would say that LFENCE is required for memory consistency. Even MOVNTDQA - the only non-temporal load instruction so far - mentions MFENCE but not LFENCE.

---

Update: see answers on Why is (or isn't?) SFENCE + LFENCE equivalent to MFENCE? for correct answers to the guesswork below

Whether MFENCE is equivalent to a "sum" of other two fences or not is a tricky question. At glance, among the three fence instructions only MFENCE provides StoreLoad barrier, i.e. prevents reordering of reads with earlier writes. However the correct answer requires to know more than the above rules; namely, it's important that all fence instructions are ordered with respect to each other. This makes the SFENCE LFENCE sequence more powerful than a mere union of individual effects: this sequence also prevents StoreLoad reordering (because loads cannot pass LFENCE, which cannot pass SFENCE, which cannot pass stores), and thus constitutes a full memory fence (but also see the note (*) below). Note however that order matters here, and the LFENCE SFENCE sequence does not have the same synergy effect.

However, while one can say that MFENCE ~ SFENCE LFENCE and LFENCE ~ NOP, that does not mean MFENCE ~ SFENCE. I deliberately use equivalence (~) and not equality (=) to stress that arithmetic rules do not apply here. The mutual effect of SFENCE followed by LFENCE makes the difference; even though loads are not reordered with each other, LFENCE is required to prevent reordering of loads with SFENCE.

(*) It still might be correct to say that MFENCE is stronger than the combination of the other two fences. In particular, a note to CLFLUSH instruction in the volume 2 of Intel's manual says that "CLFLUSH is only ordered by the MFENCE instruction. It is not guaranteed to be ordered by any other fencing or serializing instructions or by another CLFLUSH instruction."

(Update, clflush is now defined as strongly ordered (like a normal store, so you only need mfence if you want to block later loads), but clflushopt is weakly ordered, but can be fenced by sfence.)