Python uhd_interface.uhd_transmitter函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› Python›Python编程经验

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了Python中uhd_interface.uhd_transmitter函数的典型用法代码示例。如果您正苦于以下问题：Python uhd_transmitter函数的具体用法？Python uhd_transmitter怎么用？Python uhd_transmitter使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了uhd_transmitter函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的Python代码示例。

示例1: init

    def __init__(self, options):
        gr.top_block.__init__(self)

        if options.outfile is not None:
          u = gr.file_sink(gr.sizeof_gr_complex, options.outfile)
        elif (options.tx_freq is not None) or (options.channel is not None):
          if options.channel is not None:
            self.chan_num = options.channel
            options.tx_freq = ieee802_15_4_pkt.chan_802_15_4.chan_map[self.chan_num]

          u = uhd_transmitter(options.tx_args,
                              options.bandwidth,
                              options.tx_freq, options.tx_gain,
                              options.spec, options.antenna,
                              options.verbose, options.external)
        else:
          raise SystemExit("--tx-freq, --channel or --outfile must be specified\n")

        self.samples_per_symbol = 2

        # transmitter
        self.packet_transmitter = ieee802_15_4_pkt.ieee802_15_4_mod_pkts(self,
                spb=self.samples_per_symbol, msgq_limit=2, log=options.log)
        self.amp = gr.multiply_const_cc(1)

        self.u = u
        self.connect(self.packet_transmitter, self.amp, self.u)

        self.connect(self.amp, gr.file_sink(gr.sizeof_gr_complex, 'cc2420-tx-diag.dat'))

开发者ID:UpYou，项目名称:gr-ieee802-15-4，代码行数:29，代码来源:cc2420_txtest_uhd.py

示例2: _setup_sink

	def _setup_sink(self, options):
            self.symbol_rate=2; #for bpsk will edit the code later to set this automaticly based on the selected modulation scheme
	    self.sink = uhd_transmitter(options.args, self.symbol_rate,
                                        options.samples_per_symbol,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)

开发者ID:nagsrk，项目名称:ofdm_uhd，代码行数:7，代码来源:usrp_transmit_path.py

示例3: init

    def __init__(self, options, payload=''):
        gr.top_block.__init__(self)

	if(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.args,
                                        options.bandwidth,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)
        elif(options.to_file is not None):
            self.sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            self.sink = gr.null_sink(gr.sizeof_gr_complex)

	options.interp	= 100e6/options.bandwidth	# FTW-specific convertion

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        if(options.from_file is None):
            self.txpath = ftw_transmit_path(options, payload)    
        else:
            self.txpath = gr.file_source(gr.sizeof_gr_complex, options.from_file);
#            options.tx_amplitude = 1

        # static value to make sure we do not exceed +-1 for the floats being sent to the sink
	self._tx_amplitude = options.tx_amplitude        
	self.amp = gr.multiply_const_cc(self._tx_amplitude)

        # self.txpath = ftw_pnc_transmit_path(options, payload)
        self.connect(self.txpath, self.amp, self.sink)

        if options.log:
            self.connect(self.txpath, gr.file_sink(gr.sizeof_gr_complex, 'ftw_benchmark.dat'))

开发者ID:aler86，项目名称:radioplus，代码行数:33，代码来源:ftw_ofdm_tx_uhd.py

示例4: init

    def __init__(self, modulator_class, options):
        gr.top_block.__init__(self)
        self.txpath = transmit_path(modulator_class, options)
        self.audio_rx = audio_rx(options.audio_input)

        if(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.address, options.bitrate,
                                        options.samples_per_symbol,
                                        options.tx_freq, options.tx_gain,
                                        options.antenna, options.verbose)
            options.samples_per_symbol = self.sink._sps
            audio_rate = self.audio_rx.sample_rate
            usrp_rate = self.sink.get_sample_rate()
            rrate = usrp_rate / audio_rate
            
        elif(options.to_file is not None):
            self.sink = blocks.file_sink(gr.sizeof_gr_complex, options.to_file)
            rrate = 1
        else:
            self.sink = blocks.null_sink(gr.sizeof_gr_complex)
            rrate = 1

        self.resampler = filter.pfb.arb_resampler_ccf(rrate)
            
	self.connect(self.audio_rx)
	self.connect(self.txpath, self.resampler, self.sink)

开发者ID:bolin-hsu，项目名称:jelli-gnuradio，代码行数:26，代码来源:tx_voice.py

示例5: init

    def __init__(self, modulator, options):
        gr.top_block.__init__(self)

        if(options.tx_freq is not None):
            # Work-around to get the modulation's bits_per_symbol
            args = modulator.extract_kwargs_from_options(options)
            symbol_rate = options.bitrate / modulator(**args).bits_per_symbol()

            self.sink = uhd_transmitter(options.args, symbol_rate,
                                        options.samples_per_symbol,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)
            options.samples_per_symbol = self.sink._sps
            
        elif(options.to_file is not None):
            sys.stderr.write(("Saving samples to '%s'.\n\n" % (options.to_file)))
            self.sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            sys.stderr.write("No sink defined, dumping samples to null sink.\n\n")
            self.sink = gr.null_sink(gr.sizeof_gr_complex)

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = transmit_path(modulator, options)

        self.connect(self.txpath, self.sink)

开发者ID:randyp1248，项目名称:darpa，代码行数:27，代码来源:benchmark_tx3.py

示例6: init

    def __init__(self, callback, options):
        gr.top_block.__init__(self)

        self.source = uhd_receiver(
            options.args,
            options.bandwidth,
            options.rx_freq,
            options.rx_gain,
            options.spec,
            options.antenna,
            options.verbose,
        )

        self.sink = uhd_transmitter(
            options.args,
            options.bandwidth,
            options.tx_freq,
            options.tx_gain,
            options.spec,
            options.antenna,
            options.verbose,
        )

        self.txpath = transmit_path(options)
        self.rxpath = receive_path(callback, options)

        self.connect(self.txpath, self.sink)
        self.connect(self.source, self.rxpath)

开发者ID:Wysaat，项目名称:gnuradio，代码行数:28，代码来源:tunnel.py

示例7: init

    def __init__(self, mod_class, demod_class,
                 rx_callback, options):

        gr.top_block.__init__(self)

        # Get the modulation's bits_per_symbol
        args = mod_class.extract_kwargs_from_options(options)
        symbol_rate = options.bitrate / mod_class(**args).bits_per_symbol()

        self.source = uhd_receiver(options.args, symbol_rate,
                                   options.samples_per_symbol,
                                   options.rx_freq, options.rx_gain,
                                   options.spec, options.antenna,
                                   options.verbose)
        
        self.sink = uhd_transmitter(options.args, symbol_rate,
                                    options.samples_per_symbol,
                                    options.tx_freq, options.tx_gain,
                                    options.spec, options.antenna,
                                    options.verbose)
        
        options.samples_per_symbol = self.source._sps

        self.txpath = transmit_path(mod_class, options)
        self.rxpath = receive_path(demod_class, rx_callback, options)
        self.connect(self.txpath, self.sink)
        self.connect(self.source, self.rxpath)

开发者ID:manuts，项目名称:stop-and-wait-arq，代码行数:27，代码来源:tunnel.py

示例8: init

    def __init__(self, callback, options):
        gr.top_block.__init__(self)

	### Rx Side ###

        if(options.rx_freq is not None):
            self.source = uhd_receiver(options.args_rx,
                                       options.bandwidth,
                                       options.rx_freq, options.rx_gain,
                                       options.spec, options.antenna,
                                       options.verbose)
        elif(options.from_file is not None):
            self.source = gr.file_source(gr.sizeof_gr_complex, options.from_file)
        else:
            self.source = gr.null_source(gr.sizeof_gr_complex)


        # Set up receive path
        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.rxpath = receive_path(callback, options)

        
	## Tx Side ###
	if(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.args_tx,
                                        options.bandwidth,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)
        elif(options.to_file is not None):
            self.sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            self.sink = gr.null_sink(gr.sizeof_gr_complex)


        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = transmit_path(options)
        self.connect(self.txpath, self.sink)

#        self.txpath = gr.message_source(gr.sizeof_gr_complex, 3)
#        nco_sensitivity = 2.0/options.fft_length   # correct for fine frequency
#        self.nco = ftw.pnc_frequency_modulator_fc(nco_sensitivity)
#        self.connect(self.txpath, self.sink) # self.nco, 

	# if you use two USRPs and want to synchonized
	# need to change uhd_interface.py
#	self.source.config_mimo()
#	time.sleep(1)	# to make sync stable

	if options.debug:
	    self.connect(self.source, gr.file_sink(gr.sizeof_gr_complex, 'rx.dat'))	# Save reception signal 
	else:
	    self.connect(self.source, self.rxpath)
            #self.connect(self.source, gr.file_sink(gr.sizeof_gr_complex, 'rx.dat'))

	if(options.verbose):
            self._print_verbage()

开发者ID:UpYou，项目名称:ofdm，代码行数:59，代码来源:benchmark_txrx.py

示例9: init

    def __init__(self, modulator, demodulator, rx_callback, options):
        gr.top_block.__init__(self)
		#parameters to sense channe
        #options.symbol_rate=2500000
        #options.samples_per_symbol=2
        #options.rx_freq=2500000000
        #options.rx_gain=20
        #options.chbw_factor=1
        sense_symbol_rate=2500000
        sense_samples_per_symbol=2
        sense_rx_freq=2500000000
        sense_rx_gain=20
        options.chbw_factor=1
	#options.samples_per_symbol,

 
        #args = demodulator.extract_kwargs_from_options(options)
        self.sensesource=uhd_receiver(options.args, sense_symbol_rate,
                                       sense_samples_per_symbol,
                                       sense_rx_freq, sense_rx_gain,
                                       options.spec, options.antenna,
                                       options.verbose)

        if(options.tx_freq is not None):
            # Work-around to get the modulation's bits_per_symbol
            args = modulator.extract_kwargs_from_options(options)
            symbol_rate = options.bitrate / modulator(**args).bits_per_symbol()

            self.sink = uhd_transmitter(options.args, symbol_rate,
                                        options.samples_per_symbol,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)
            options.samples_per_symbol = self.sink._sps
            
        elif(options.to_file is not None):
            sys.stderr.write(("Saving samples to '%s'.\n\n" % (options.to_file)))
            self.sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            sys.stderr.write("No sink defined, dumping samples to null sink.\n\n")
            self.sink = gr.null_sink(gr.sizeof_gr_complex)


        self.txgate = gr.copy(gr.sizeof_gr_complex)
        self.sensegate = gr.copy(gr.sizeof_gr_complex)
        #self.msgq             = gr.msg_queue()

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = transmit_path(modulator, options)

        self.connect(self.txpath, self.txgate, self.sink)

	# do sense
        self.sensepath = sensing_path(options)

        self.tx_enabled = True
	self.sense_flag=False
	self.connect(self.sensesource, self.sensepath)

开发者ID:tyc85，项目名称:nwsdr-3.6.3-dsc，代码行数:59，代码来源:benchmarksenseFinal_tx.py

示例10: init

 def __init__(self, options):
     gr.top_block.__init__(self)
     self.sink = uhd_transmitter(options.args,
                                 options.bandwidth, options.tx_freq,
                                 options.lo_offset, options.tx_gain,
                                 options.spec, options.antenna,
                                 options.clock_source, options.verbose)
     self.txpath = transmit_path(options)
     self.connect(self.txpath, self.sink)

开发者ID:teoyenmao，项目名称:usrp_project，代码行数:9，代码来源:test_uci.py

示例11: init

    def __init__(self, rx_callback, options):
        gr.top_block.__init__(self)

        # Setting up 'Transmit Path'
        self.txpath = transmit_path(options, self)

        # Setting up 'Receive Path'
        packet = cnPacket()
        self.rxpath = receive_path(rx_callback, packet, options) 

        # Channel
        samples_per_packet = options.samples_per_symbol * 8 * 36
 
        if options.mode == 'default':
            print 'Operating mode : Default'
            
            mods = digital.modulation_utils.type_1_mods()
            modulator = mods[options.modulation]
            
            args = modulator.extract_kwargs_from_options(options)
            symbol_rate = options.bitrate / modulator(**args).bits_per_symbol()

            self.usrp_sink = uhd_transmitter(options.args, symbol_rate,
                                        options.samples_per_symbol,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)

            self.usrp_source = uhd_receiver(options.args, symbol_rate,
                                       options.samples_per_symbol,
                                       options.rx_freq, options.rx_gain,
                                       options.spec, options.antenna,
                                       options.verbose)

            options.samples_per_symbol = self.usrp_sink._sps
            
            
            #self.usrp_sink = usrp_sink(options)
            #self.usrp_source = usrp_source(options)
            self.connect(self.txpath, self.usrp_sink)
            self.connect(self.usrp_source, self.rxpath)

            
        elif options.mode == 'loopback':
            print 'Operating mode : Loopback'
      
            self.channel = channel_emulator(options,samples_per_packet)
            self.connect(self.txpath, self.channel, self.rxpath)

开发者ID:ychang，项目名称:gr-gtlib，代码行数:48，代码来源:cnPHY.py

示例12: init

    def __init__(self, options):
        gr.top_block.__init__(self)

        
        self.sink = uhd_transmitter(options.args,
                                    options.bandwidth,
                                    options.tx_freq, options.tx_gain,
                                    options.spec, options.antenna,
                                    options.verbose)
  

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = transmit_path(options)

        self.connect(self.txpath, self.sink)

开发者ID:xiaov58，项目名称:Coolest_Path，代码行数:16，代码来源:benchmark_tx.py

示例13: _setup_usrp_source2

    def _setup_usrp_source2(self,options):
        """
        Creates a USRP sink, determines the settings for best bitrate,
        and attaches to the transmitter's subdevice.
        """
        print "setup_usrp_source2",self._tx_freq

        if(self._tx_freq is not None):
            self.u_sink = uhd_transmitter(options.args,
                                        options.bandwidth,
                                        self._tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)
        print "setup usrp sink " , self.u_sink
        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = transmit_path(options)
        self.connect(self.txpath, self.u_sink)

开发者ID:jbruno，项目名称:gr_papyrus，代码行数:18，代码来源:ssma.py

示例14: init

    def __init__(self, options):
        gr.top_block.__init__(self)

        if(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.args,
                                        options.bandwidth, options.tx_freq, 
                                        options.lo_offset, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.clock_source, options.verbose)
        elif(options.to_file is not None):
            self.sink = blocks.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            self.sink = blocks.null_sink(gr.sizeof_gr_complex)

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = transmit_path(options)

        self.connect(self.txpath, self.sink)

开发者ID:phoorichet，项目名称:gnuradio，代码行数:19，代码来源:benchmark_tx.py

示例15: init

    def __init__(self, options):
        gr.top_block.__init__(self)

        if(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.args,
                                        options.bandwidth,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)
        elif(options.to_file is not None):
            self.sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            self.sink = gr.null_sink(gr.sizeof_gr_complex)

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        self.txpath = gr.message_source(gr.sizeof_gr_complex, 3)
        self.amp = gr.multiply_const_cc(options.amp)
        self.connect(self.txpath, self.amp, self.sink)

开发者ID:UpYou，项目名称:gnuradio-tools，代码行数:19，代码来源:raw_msgqtx.py

示例16: init

    def __init__(self, options):
        gr.top_block.__init__(self)

        data_capsule = ( (+0+0j), (+0+0j), (+0+0j), (+0+0j), (+0+0j),
                         (+1+1j), (+1+1j), (+1+1j), (+1+1j), (+1+1j) )

        symbol_rate = 500000

        self.source = uhd_receiver(options.args, symbol_rate,
                                   2,
                                   options.rx_freq, 30,
                                   options.spec, "RX2",
                                   options.verbose)

        self.tx = uhd_transmitter(options.args, symbol_rate,
                                    2,
                                    options.tx_freq, 30,
                                    options.spec, "TX/RX", 
                                    options.verbose)

        options.samples_per_symbol = self.source._sps

        # Set up receive path
        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
 
        self.serve = gr.vector_source_c(data_capsule)
        
        #self.correlator = correlator_cc.correlator_cc()

        #self.sink = gr.vector_sink_c()
        #self.file_sink = gr.file_sink(gr.sizeof_gr_complex, "out")

        self.server = correlator_cc.go_start_cc()
        self.inserter = correlator_cc.preamble_insert_cc()
        self.correlator = correlator_cc.correlator_cc()
      
        self.connect(self.source, self.correlator)
        self.connect(self.serve, (self.server,0))
        self.connect(self.correlator, (self.server,1))
       
        self.connect(self.server, self.inserter)
        self.connect(self.inserter, self.tx)

开发者ID:randyp1248，项目名称:darpa，代码行数:43，代码来源:rx_pingpong.py

示例17: init

    def __init__(self, callback, fwd_callback, options):
    #def __init__(self, options):
        gr.top_block.__init__(self)

        if(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.args,
                                        options.bandwidth,
                                        options.tx_freq, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.verbose)

	if(options.rx_freq is not None):
            self.source = uhd_receiver(options.args,
                                       options.bandwidth,
                                       options.rx_freq, options.rx_gain,
                                       options.spec, options.antenna,
                                       options.verbose)

        elif(options.to_file is not None):
            self.sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            self.sink = gr.null_sink(gr.sizeof_gr_complex)

        # do this after for any adjustments to the options that may
        # occur in the sinks (specifically the UHD sink)
        print "flow:: ", options.flow

        # only for bidirectional flows: source in the reverse direction needs to 
        # start the ofdm_sink first to allow the socket connections working fine.. 
        if (options.flow == 1):
            self.rxpath = receive_path(callback, fwd_callback, options)
            self.connect(self.source, self.rxpath)

            self.txpath = transmit_path(options)
            self.connect(self.txpath, self.sink)
        else:
            self.txpath = transmit_path(options)
            self.connect(self.txpath, self.sink)

            self.rxpath = receive_path(callback, fwd_callback, options)
            self.connect(self.source, self.rxpath)

开发者ID:gnychis，项目名称:gnuradio-3.5.0-dmr，代码行数:41，代码来源:benchmark.py

示例18: init

  def __init__(self, options):
    gr.top_block.__init__(self)

    if options.tx_freq is not None:
      u = uhd_transmitter(options.args,
                          options.bandwidth,
                          options.tx_freq, options.tx_gain,
                          options.spec, options.antenna,
                          options.external, options.verbose)
    elif options.outfile is not None:
      u = gr.file_sink(gr.sizeof_gr_complex, options.outfile)
    else:
      raise SystemExit("--freq or --outfile must be specified\n")

    if options.infile is not None:
      tx = gr.file_source(gr.sizeof_gr_complex, options.infile, repeat = options.repeat)
    else:
      tx = ofdm_rxtx.TX(options)
      data_tones = tx.params.data_tones
      if options.char > 0:
        # read char from file
        data = gr.stream_to_vector(gr.sizeof_float, data_tones * 2)
        # NOTE: we use repeat, assuming the file is long enough or properly aligned
        self.connect(gr.file_source(gr.sizeof_char, options.txdata, repeat=True),
                     gr.char_to_float(),
                     gr.multiply_const_ff(options.char * (2**-0.5) / 128.0),
                     data)
      else:
        data = ofdm_rxtx.make_data(data_tones, options.size, options.txdata)
        if options.log:
          self.connect(data, gr.file_sink(data_tones * gr.sizeof_gr_complex, 'tx-data.dat'))

      self.connect(data, tx)
      self.sender = ofdm_rxtx.sender_thread(tx, options)

    if options.amp != 1:
      amp = gr.multiply_const_cc(options.amp)
      self.connect(tx, amp, u)
    else:
      self.connect(tx, u)

开发者ID:UpYou，项目名称:ofdm，代码行数:40，代码来源:ofdm_tx.py

示例19: init

    def __init__(self, options):
        gr.top_block.__init__(self)

        if(options.to_file is not None):
            self.file = blocks.file_sink(gr.sizeof_gr_complex, options.to_file)
            self.sink = blocks.throttle(gr.sizeof_gr_complex,1e6)
            self.connect( self.sink, self.file )
        elif(options.tx_freq is not None):
            self.sink = uhd_transmitter(options.args,
                                        options.bandwidth, options.tx_freq, 
                                        options.lo_offset, options.tx_gain,
                                        options.spec, options.antenna,
                                        options.clock_source, options.verbose)
        else:
            self.sink = blocks.null_sink(gr.sizeof_gr_complex)



        self._setup_tx_path(options)
        self._setup_rpc_manager()

        if options.freqoff is not None:
            freq_off = self.freq_off = channel.freq_offset(options.freqoff )
            self.connect(self.txpath, freq_off)
            self.txpath = freq_off
            self.rpc_mgr_tx.add_interface("set_freq_offset",self.freq_off.set_freqoff)

        if options.multipath:
          if options.itu_channel:
            self.fad_chan = channel.itpp_channel(options.bandwidth)
            self.rpc_mgr_tx.add_interface("set_channel_profile",self.fad_chan.set_channel_profile)
          else:
            self.fad_chan = filter.fir_filter_ccc(1,[1.0,0.0,2e-1+0.1j,1e-4-0.04j])

          self.connect(self.txpath, self.fad_chan)
          self.txpath = self.fad_chan


        self.connect(self.txpath, self.sink)

开发者ID:WindyCitySDR，项目名称:gr-ofdm，代码行数:39，代码来源:tx.py

示例20: init

    def __init__(self, mod, options):
        gr.top_block.__init__(self, "tx_mpsk")

        self._modulator_class = mod

        # Get mod_kwargs
        mod_kwargs = self._modulator_class.extract_kwargs_from_options(options)

        # transmitter
        self._modulator = self._modulator_class(**mod_kwargs)

        if options.tx_freq is not None:
            self._sink = uhd_transmitter(
                options.args,
                options.bitrate,
                options.samples_per_symbol,
                options.tx_freq,
                options.tx_gain,
                options.antenna,
                options.verbose,
            )
            options.samples_per_symbol = self._sink._sps

        elif options.to_file is not None:
            self._sink = gr.file_sink(gr.sizeof_gr_complex, options.to_file)
        else:
            self._sink = gr.null_sink(gr.sizeof_gr_complex)

        self._transmitter = bert_transmit(
            self._modulator._constellation,
            options.samples_per_symbol,
            options.differential,
            options.excess_bw,
            gray_coded=True,
            verbose=options.verbose,
            log=options.log,
        )

        self.connect(self._transmitter, self._sink)

开发者ID:n4hy，项目名称:gnuradio，代码行数:39，代码来源:digital_bert_tx.py

注：本文中的uhd_interface.uhd_transmitter函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

Python uhd_receiver.add_options函数代码示例发布时间：2022-05-27

Python uhd_interface.uhd_receiver函数代码示例发布时间：2022-05-27

Python util.grid_equal函数代码示例

1 Python 入门教程

Python入门教程 Python 是一种解释型、面向对象、动态数据类型的高级程序设计语言。 P

阅读：13925|2022-01-22

2 Python wikiutil.getFrontPage函数代码示例

Python wikiutil.getFrontPage函数代码示例

阅读：10291|2022-05-24

3 Python 简介

Python 简介 Python 是一个高层次的结合了解释性、编译性、互动性和面向对象的脚本

阅读：4165|2022-01-22

4 Python tests.group函数代码示例

Python tests.group函数代码示例

阅读：4064|2022-05-27

5 Python util.check_if_user_has_permission

Python util.check_if_user_has_permission函数代码示例

阅读：3889|2022-05-27

6 Python 操练实例98

Python 练习实例98 Python 100例题目：从键盘输入一个字符串，将小写字母全部转换成大

阅读：3538|2022-01-22

7 Python 环境搭建

Python 环境搭建本章节我们将向大家介绍如何在本地搭建 Python 开发环境。 Py

阅读：3065|2022-01-22

8 Python 基础语法

Python 基础语法 Python 语言与 Perl，C 和 Java 等语言有许多相似之处。但是，也

阅读：2723|2022-01-22

9 Python output.darkgreen函数代码示例

Python output.darkgreen函数代码示例

阅读：2682|2022-05-25

10 Python 中文编码

Python 中文编码前面章节中我们已经学会了如何用 Python 输出 Hello, World!，英文没

阅读：2344|2022-01-22

客服电话

电子邮件

Python uhd_interface.uhd_transmitter函数代码示例

示例1: __init__

示例2: _setup_sink

示例3: __init__

示例4: __init__

示例5: __init__

示例6: __init__

示例7: __init__

示例8: __init__

示例9: __init__

示例10: __init__

示例11: __init__

示例12: __init__

示例13: _setup_usrp_source2

示例14: __init__

示例15: __init__

示例16: __init__

示例17: __init__

示例18: __init__

示例19: __init__

示例20: __init__

请发表评论

全部评论

上一篇：

下一篇：

Python util.grid_equal函数代码示例

Python util.get_worker_name函数代码示例

Python util.get_webmention_target函数代

Python util.get_uuid函数代码示例

Python util.get_type_by_name函数代码示例

Python util.grid_equal函数代码示例

Python util.get_worker_name函数代码示例

Python util.get_webmention_target函数代

Python util.get_uuid函数代码示例

Python util.get_type_by_name函数代码示例

Python util.get_stdout函数代码示例

关于我们

产品与服务

解决方案

139-2527-9053

示例1: init

示例3: init

示例4: init

示例5: init

示例6: init

示例7: init

示例8: init

示例9: init

示例10: init

示例11: init

示例12: init

示例14: init

示例15: init

示例16: init

示例17: init

示例18: init

示例19: init

示例20: init