C++ snd_soc_register_codec函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中snd_soc_register_codec函数的典型用法代码示例。如果您正苦于以下问题：C++ snd_soc_register_codec函数的具体用法？C++ snd_soc_register_codec怎么用？C++ snd_soc_register_codec使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了snd_soc_register_codec函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: gbcodec_i2c_probe

static int gbcodec_i2c_probe(struct i2c_client *i2c,
		    const struct i2c_device_id *id)
{
	return snd_soc_register_codec(&i2c->dev, &soc_codec_dev_gbcodec,
				      gbcodec_dai, ARRAY_SIZE(gbcodec_dai));
}

开发者ID:AresHou，项目名称:audio，代码行数:6，代码来源:virtual-codec.c

示例2: adau1701_i2c_probe


//.........这里部分代码省略.........
		return -ENOMEM;

	for (i = 0; i < ARRAY_SIZE(supply_names); i++)
		adau1701->supplies[i].supply = supply_names[i];

	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(adau1701->supplies),
			adau1701->supplies);
	if (ret < 0) {
		dev_err(dev, "Failed to get regulators: %d\n", ret);
		return ret;
	}

	ret = regulator_bulk_enable(ARRAY_SIZE(adau1701->supplies),
			adau1701->supplies);
	if (ret < 0) {
		dev_err(dev, "Failed to enable regulators: %d\n", ret);
		return ret;
	}

	adau1701->client = client;
	adau1701->regmap = devm_regmap_init(dev, NULL, client,
					    &adau1701_regmap);
	if (IS_ERR(adau1701->regmap)) {
		ret = PTR_ERR(adau1701->regmap);
		goto exit_regulators_disable;
	}


	if (dev->of_node) {
		gpio_nreset = of_get_named_gpio(dev->of_node, "reset-gpio", 0);
		if (gpio_nreset < 0 && gpio_nreset != -ENOENT) {
			ret = gpio_nreset;
			goto exit_regulators_disable;
		}

		gpio_pll_mode[0] = of_get_named_gpio(dev->of_node,
						   "adi,pll-mode-gpios", 0);
		if (gpio_pll_mode[0] < 0 && gpio_pll_mode[0] != -ENOENT) {
			ret = gpio_pll_mode[0];
			goto exit_regulators_disable;
		}

		gpio_pll_mode[1] = of_get_named_gpio(dev->of_node,
						   "adi,pll-mode-gpios", 1);
		if (gpio_pll_mode[1] < 0 && gpio_pll_mode[1] != -ENOENT) {
			ret = gpio_pll_mode[1];
			goto exit_regulators_disable;
		}

		of_property_read_u32(dev->of_node, "adi,pll-clkdiv",
				     &adau1701->pll_clkdiv);

		of_property_read_u8_array(dev->of_node, "adi,pin-config",
					  adau1701->pin_config,
					  ARRAY_SIZE(adau1701->pin_config));
	}

	if (gpio_is_valid(gpio_nreset)) {
		ret = devm_gpio_request_one(dev, gpio_nreset, GPIOF_OUT_INIT_LOW,
					    "ADAU1701 Reset");
		if (ret < 0)
			goto exit_regulators_disable;
	}

	if (gpio_is_valid(gpio_pll_mode[0]) &&
	    gpio_is_valid(gpio_pll_mode[1])) {
		ret = devm_gpio_request_one(dev, gpio_pll_mode[0],
					    GPIOF_OUT_INIT_LOW,
					    "ADAU1701 PLL mode 0");
		if (ret < 0)
			goto exit_regulators_disable;

		ret = devm_gpio_request_one(dev, gpio_pll_mode[1],
					    GPIOF_OUT_INIT_LOW,
					    "ADAU1701 PLL mode 1");
		if (ret < 0)
			goto exit_regulators_disable;
	}

	adau1701->gpio_nreset = gpio_nreset;
	adau1701->gpio_pll_mode[0] = gpio_pll_mode[0];
	adau1701->gpio_pll_mode[1] = gpio_pll_mode[1];

	i2c_set_clientdata(client, adau1701);

	adau1701->sigmadsp = devm_sigmadsp_init_i2c(client,
		&adau1701_sigmadsp_ops, ADAU1701_FIRMWARE);
	if (IS_ERR(adau1701->sigmadsp)) {
		ret = PTR_ERR(adau1701->sigmadsp);
		goto exit_regulators_disable;
	}

	ret = snd_soc_register_codec(&client->dev, &adau1701_codec_drv,
			&adau1701_dai, 1);

exit_regulators_disable:

	regulator_bulk_disable(ARRAY_SIZE(adau1701->supplies), adau1701->supplies);
	return ret;
}

开发者ID:AshishNamdev，项目名称:linux，代码行数:101，代码来源:adau1701.c

示例3: wm2000_i2c_probe


//.........这里部分代码省略.........
			      GFP_KERNEL);
	if (!wm2000)
		return -ENOMEM;

	mutex_init(&wm2000->lock);

	dev_set_drvdata(&i2c->dev, wm2000);

	wm2000->regmap = devm_regmap_init_i2c(i2c, &wm2000_regmap);
	if (IS_ERR(wm2000->regmap)) {
		ret = PTR_ERR(wm2000->regmap);
		dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
			ret);
		goto out;
	}

	for (i = 0; i < WM2000_NUM_SUPPLIES; i++)
		wm2000->supplies[i].supply = wm2000_supplies[i];

	ret = devm_regulator_bulk_get(&i2c->dev, WM2000_NUM_SUPPLIES,
				      wm2000->supplies);
	if (ret != 0) {
		dev_err(&i2c->dev, "Failed to get supplies: %d\n", ret);
		return ret;
	}

	ret = regulator_bulk_enable(WM2000_NUM_SUPPLIES, wm2000->supplies);
	if (ret != 0) {
		dev_err(&i2c->dev, "Failed to enable supplies: %d\n", ret);
		return ret;
	}

	/* Verify that this is a WM2000 */
	reg = wm2000_read(i2c, WM2000_REG_ID1);
	id = reg << 8;
	reg = wm2000_read(i2c, WM2000_REG_ID2);
	id |= reg & 0xff;

	if (id != 0x2000) {
		dev_err(&i2c->dev, "Device is not a WM2000 - ID %x\n", id);
		ret = -ENODEV;
		goto err_supplies;
	}

	reg = wm2000_read(i2c, WM2000_REG_REVISON);
	dev_info(&i2c->dev, "revision %c\n", reg + 'A');

	wm2000->mclk = devm_clk_get(&i2c->dev, "MCLK");
	if (IS_ERR(wm2000->mclk)) {
		ret = PTR_ERR(wm2000->mclk);
		dev_err(&i2c->dev, "Failed to get MCLK: %d\n", ret);
		goto err_supplies;
	}

	filename = "wm2000_anc.bin";
	pdata = dev_get_platdata(&i2c->dev);
	if (pdata) {
		wm2000->speech_clarity = !pdata->speech_enh_disable;

		if (pdata->download_file)
			filename = pdata->download_file;
	}

	ret = request_firmware(&fw, filename, &i2c->dev);
	if (ret != 0) {
		dev_err(&i2c->dev, "Failed to acquire ANC data: %d\n", ret);
		goto err_supplies;
	}

	/* Pre-cook the concatenation of the register address onto the image */
	wm2000->anc_download_size = fw->size + 2;
	wm2000->anc_download = devm_kzalloc(&i2c->dev,
					    wm2000->anc_download_size,
					    GFP_KERNEL);
	if (wm2000->anc_download == NULL) {
		dev_err(&i2c->dev, "Out of memory\n");
		ret = -ENOMEM;
		goto err_supplies;
	}

	wm2000->anc_download[0] = 0x80;
	wm2000->anc_download[1] = 0x00;
	memcpy(wm2000->anc_download + 2, fw->data, fw->size);

	wm2000->anc_eng_ena = 1;
	wm2000->anc_active = 1;
	wm2000->spk_ena = 1;
	wm2000->i2c = i2c;

	wm2000_reset(wm2000);

	ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000, NULL, 0);

err_supplies:
	regulator_bulk_disable(WM2000_NUM_SUPPLIES, wm2000->supplies);

out:
	release_firmware(fw);
	return ret;
}

开发者ID:Abioy，项目名称:kasan，代码行数:101，代码来源:wm2000.c

示例4: ac97_probe

static int ac97_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev,
			&soc_codec_dev_ac97, &ac97_dai, 1);
}

开发者ID:19Dan01，项目名称:linux，代码行数:5，代码来源:ac97.c

示例5: wm8961_register

static int wm8961_register(struct wm8961_priv *wm8961)
{
	struct snd_soc_codec *codec = &wm8961->codec;
	int ret;
	u16 reg;

	if (wm8961_codec) {
		dev_err(codec->dev, "Another WM8961 is registered\n");
		ret = -EINVAL;
		goto err;
	}

	mutex_init(&codec->mutex);
	INIT_LIST_HEAD(&codec->dapm_widgets);
	INIT_LIST_HEAD(&codec->dapm_paths);

	snd_soc_codec_set_drvdata(codec, wm8961);
	codec->name = "WM8961";
	codec->owner = THIS_MODULE;
	codec->dai = &wm8961_dai;
	codec->num_dai = 1;
	codec->reg_cache_size = ARRAY_SIZE(wm8961->reg_cache);
	codec->reg_cache = &wm8961->reg_cache;
	codec->bias_level = SND_SOC_BIAS_OFF;
	codec->set_bias_level = wm8961_set_bias_level;
	codec->volatile_register = wm8961_volatile_register;

	memcpy(codec->reg_cache, wm8961_reg_defaults,
	       sizeof(wm8961_reg_defaults));

	ret = snd_soc_codec_set_cache_io(codec, 8, 16, SND_SOC_I2C);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to set cache I/O: %d\n", ret);
		goto err;
	}

	reg = snd_soc_read(codec, WM8961_SOFTWARE_RESET);
	if (reg != 0x1801) {
		dev_err(codec->dev, "Device is not a WM8961: ID=0x%x\n", reg);
		ret = -EINVAL;
		goto err;
	}

	/* This isn't volatile - readback doesn't correspond to write */
	reg = codec->hw_read(codec, WM8961_RIGHT_INPUT_VOLUME);
	dev_info(codec->dev, "WM8961 family %d revision %c\n",
		 (reg & WM8961_DEVICE_ID_MASK) >> WM8961_DEVICE_ID_SHIFT,
		 ((reg & WM8961_CHIP_REV_MASK) >> WM8961_CHIP_REV_SHIFT)
		 + 'A');

	ret = wm8961_reset(codec);
	if (ret < 0) {
		dev_err(codec->dev, "Failed to issue reset\n");
		return ret;
	}

	/* Enable class W */
	reg = snd_soc_read(codec, WM8961_CHARGE_PUMP_B);
	reg |= WM8961_CP_DYN_PWR_MASK;
	snd_soc_write(codec, WM8961_CHARGE_PUMP_B, reg);

	/* Latch volume update bits (right channel only, we always
	 * write both out) and default ZC on. */
	reg = snd_soc_read(codec, WM8961_ROUT1_VOLUME);
	snd_soc_write(codec, WM8961_ROUT1_VOLUME,
		     reg | WM8961_LO1ZC | WM8961_OUT1VU);
	snd_soc_write(codec, WM8961_LOUT1_VOLUME, reg | WM8961_LO1ZC);
	reg = snd_soc_read(codec, WM8961_ROUT2_VOLUME);
	snd_soc_write(codec, WM8961_ROUT2_VOLUME,
		     reg | WM8961_SPKRZC | WM8961_SPKVU);
	snd_soc_write(codec, WM8961_LOUT2_VOLUME, reg | WM8961_SPKLZC);

	reg = snd_soc_read(codec, WM8961_RIGHT_ADC_VOLUME);
	snd_soc_write(codec, WM8961_RIGHT_ADC_VOLUME, reg | WM8961_ADCVU);
	reg = snd_soc_read(codec, WM8961_RIGHT_INPUT_VOLUME);
	snd_soc_write(codec, WM8961_RIGHT_INPUT_VOLUME, reg | WM8961_IPVU);

	/* Use soft mute by default */
	reg = snd_soc_read(codec, WM8961_ADC_DAC_CONTROL_2);
	reg |= WM8961_DACSMM;
	snd_soc_write(codec, WM8961_ADC_DAC_CONTROL_2, reg);

	/* Use automatic clocking mode by default; for now this is all
	 * we support.
	 */
	reg = snd_soc_read(codec, WM8961_CLOCKING_3);
	reg &= ~WM8961_MANUAL_MODE;
	snd_soc_write(codec, WM8961_CLOCKING_3, reg);

	wm8961_set_bias_level(codec, SND_SOC_BIAS_STANDBY);

	wm8961_dai.dev = codec->dev;

	wm8961_codec = codec;

	ret = snd_soc_register_codec(codec);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to register codec: %d\n", ret);
		return ret;
	}
//.........这里部分代码省略.........

开发者ID:12rafael，项目名称:jellytimekernel，代码行数:101，代码来源:wm8961.c

示例6: wm8523_register

static int wm8523_register(struct wm8523_priv *wm8523,
			   enum snd_soc_control_type control)
{
	int ret;
	struct snd_soc_codec *codec = &wm8523->codec;
	int i;

	if (wm8523_codec) {
		dev_err(codec->dev, "Another WM8523 is registered\n");
		return -EINVAL;
	}

	mutex_init(&codec->mutex);
	INIT_LIST_HEAD(&codec->dapm_widgets);
	INIT_LIST_HEAD(&codec->dapm_paths);

	snd_soc_codec_set_drvdata(codec, wm8523);
	codec->name = "WM8523";
	codec->owner = THIS_MODULE;
	codec->bias_level = SND_SOC_BIAS_OFF;
	codec->set_bias_level = wm8523_set_bias_level;
	codec->dai = &wm8523_dai;
	codec->num_dai = 1;
	codec->reg_cache_size = WM8523_REGISTER_COUNT;
	codec->reg_cache = &wm8523->reg_cache;
	codec->volatile_register = wm8523_volatile_register;

	wm8523->rate_constraint.list = &wm8523->rate_constraint_list[0];
	wm8523->rate_constraint.count =
		ARRAY_SIZE(wm8523->rate_constraint_list);

	memcpy(codec->reg_cache, wm8523_reg, sizeof(wm8523_reg));

	ret = snd_soc_codec_set_cache_io(codec, 8, 16, control);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to set cache I/O: %d\n", ret);
		goto err;
	}

	for (i = 0; i < ARRAY_SIZE(wm8523->supplies); i++)
		wm8523->supplies[i].supply = wm8523_supply_names[i];

	ret = regulator_bulk_get(codec->dev, ARRAY_SIZE(wm8523->supplies),
				 wm8523->supplies);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to request supplies: %d\n", ret);
		goto err;
	}

	ret = regulator_bulk_enable(ARRAY_SIZE(wm8523->supplies),
				    wm8523->supplies);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to enable supplies: %d\n", ret);
		goto err_get;
	}

	ret = snd_soc_read(codec, WM8523_DEVICE_ID);
	if (ret < 0) {
		dev_err(codec->dev, "Failed to read ID register\n");
		goto err_enable;
	}
	if (ret != wm8523_reg[WM8523_DEVICE_ID]) {
		dev_err(codec->dev, "Device is not a WM8523, ID is %x\n", ret);
		ret = -EINVAL;
		goto err_enable;
	}

	ret = snd_soc_read(codec, WM8523_REVISION);
	if (ret < 0) {
		dev_err(codec->dev, "Failed to read revision register\n");
		goto err_enable;
	}
	dev_info(codec->dev, "revision %c\n",
		 (ret & WM8523_CHIP_REV_MASK) + 'A');

	ret = wm8523_reset(codec);
	if (ret < 0) {
		dev_err(codec->dev, "Failed to issue reset\n");
		goto err_enable;
	}

	wm8523_dai.dev = codec->dev;

	/* Change some default settings - latch VU and enable ZC */
	wm8523->reg_cache[WM8523_DAC_GAINR] |= WM8523_DACR_VU;
	wm8523->reg_cache[WM8523_DAC_CTRL3] |= WM8523_ZC;

	wm8523_set_bias_level(codec, SND_SOC_BIAS_STANDBY);

	/* Bias level configuration will have done an extra enable */
	regulator_bulk_disable(ARRAY_SIZE(wm8523->supplies), wm8523->supplies);

	wm8523_codec = codec;

	ret = snd_soc_register_codec(codec);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to register codec: %d\n", ret);
		return ret;
	}

//.........这里部分代码省略.........

开发者ID:12rafael，项目名称:jellytimekernel，代码行数:101，代码来源:wm8523.c

示例7: cg29xx_codec_driver_probe

static int __devinit cg29xx_codec_driver_probe(struct platform_device *pdev)
{
	int ret;
	struct cg29xx_codec_dai_data *dai_data;

	pr_debug("%s: Enter.\n", __func__);

	pr_info("%s: Init codec private data..\n", __func__);
	dai_data = kzalloc(CG29XX_NBR_OF_DAI * sizeof(struct cg29xx_codec_dai_data),
			GFP_KERNEL);
	if (dai_data == NULL)
		return -ENOMEM;

	dai_data[0].tx_active = 0;
	dai_data[0].rx_active = 0;
	dai_data[0].input_select = 0;
	dai_data[0].output_select = 0;
	dai_data[0].config.port = PORT_0_I2S;
	dai_data[0].config.conf.i2s.mode = DAI_MODE_SLAVE;
	dai_data[0].config.conf.i2s.half_period = HALF_PER_DUR_16;
	dai_data[0].config.conf.i2s.channel_sel = CHANNEL_SELECTION_BOTH;
	dai_data[0].config.conf.i2s.sample_rate = SAMPLE_RATE_48;
	dai_data[0].config.conf.i2s.word_width = WORD_WIDTH_32;
	dai_data[1].tx_active = 0;
	dai_data[1].rx_active = 0;
	dai_data[1].input_select = 0;
	dai_data[1].output_select = 0;
	dai_data[1].config.port = PORT_1_I2S_PCM;
	dai_data[1].config.conf.i2s_pcm.mode = DAI_MODE_SLAVE;
	dai_data[1].config.conf.i2s_pcm.slot_0_dir = DAI_DIR_B_RX_A_TX;
	dai_data[1].config.conf.i2s_pcm.slot_1_dir = DAI_DIR_B_TX_A_RX;
	dai_data[1].config.conf.i2s_pcm.slot_2_dir = DAI_DIR_B_RX_A_TX;
	dai_data[1].config.conf.i2s_pcm.slot_3_dir = DAI_DIR_B_RX_A_TX;
	dai_data[1].config.conf.i2s_pcm.slot_0_used = true;
	dai_data[1].config.conf.i2s_pcm.slot_1_used = false;
	dai_data[1].config.conf.i2s_pcm.slot_2_used = false;
	dai_data[1].config.conf.i2s_pcm.slot_3_used = false;
	dai_data[1].config.conf.i2s_pcm.slot_0_start = 0;
	dai_data[1].config.conf.i2s_pcm.slot_1_start = 16;
	dai_data[1].config.conf.i2s_pcm.slot_2_start = 32;
	dai_data[1].config.conf.i2s_pcm.slot_3_start = 48;
	dai_data[1].config.conf.i2s_pcm.protocol = PORT_PROTOCOL_PCM;
	dai_data[1].config.conf.i2s_pcm.ratio = STREAM_RATIO_FM48_VOICE16;
	dai_data[1].config.conf.i2s_pcm.duration = SYNC_DURATION_32;
	dai_data[1].config.conf.i2s_pcm.clk = BIT_CLK_512;
	dai_data[1].config.conf.i2s_pcm.sample_rate = SAMPLE_RATE_16;

	platform_set_drvdata(pdev, dai_data);

	pr_info("%s: Register codec.\n", __func__);
	ret = snd_soc_register_codec(&pdev->dev, &cg29xx_codec_driver, &cg29xx_dai_driver[0], 2);
	if (ret < 0) {
		pr_debug("%s: Error: Failed to register codec (ret = %d).\n",
			__func__,
			ret);
		snd_soc_unregister_codec(&pdev->dev);
		kfree(platform_get_drvdata(pdev));
		return ret;
	}

	return 0;
}

开发者ID:krachlatte，项目名称:Sony-Xperia-Go-ST27i，代码行数:62，代码来源:cg29xx.c

示例8: cq93vc_platform_probe

static int cq93vc_platform_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev,
			&soc_codec_dev_cq93vc, &cq93vc_dai, 1);
}

开发者ID:AnadoluPanteri，项目名称:kernel-plus-harmattan，代码行数:5，代码来源:cq93vc.c

示例9: uda134x_codec_probe

static int __devinit uda134x_codec_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev,
			&soc_codec_dev_uda134x, &uda134x_dai, 1);
}

开发者ID:CallMeVentus，项目名称:i9070_kernel_CoCore-P，代码行数:5，代码来源:uda134x.c

示例10: s5m8751_codec_probe

static int s5m8751_codec_probe(struct platform_device *pdev)
{
	struct s5m8751_priv *priv;
	struct s5m8751 *s5m8751 = dev_get_drvdata(pdev->dev.parent);
	struct s5m8751_pdata *s5m8751_pdata = s5m8751->dev->platform_data;
	struct s5m8751_audio_pdata *pdata = s5m8751_pdata->audio;
	struct snd_soc_codec *codec;
	uint8_t reg_val;
	int ret = 0;

	priv = kzalloc(sizeof(struct s5m8751_priv), GFP_KERNEL);
	if (priv == NULL)
		goto err;

	priv->s5m8751 = s5m8751;
	codec = &priv->codec;

	mutex_init(&codec->mutex);
	INIT_LIST_HEAD(&codec->dapm_widgets);
	INIT_LIST_HEAD(&codec->dapm_paths);

	snd_soc_codec_set_drvdata(codec, priv);

	codec->name = "S5M8751";
	codec->owner = THIS_MODULE;
	codec->read = s5m8751_codec_read;
	codec->write = s5m8751_codec_write;
	codec->bias_level = SND_SOC_BIAS_OFF;
	codec->set_bias_level = s5m8751_set_bias_level;
	codec->dai = &s5m8751_dai;
	codec->num_dai = 1;

	mutex_init(&codec->mutex);
	INIT_LIST_HEAD(&codec->dapm_widgets);
	INIT_LIST_HEAD(&codec->dapm_paths);

	s5m8751_codec = codec;

	reg_val = s5m8751_codec_read(codec, S5M8751_AMP_CTRL);
	s5m8751_codec_write(codec, S5M8751_AMP_CTRL, reg_val |
						S5M8751_HP_AMP_MUTE_CONTROL_ON);

	s5m8751_codec_write(codec, S5M8751_DA_PDB1, S5M8751_DA_PDB1_SPK |
						S5M8751_VMID_50K);
	s5m8751_codec_write(codec, S5M8751_DA_AMIX1, S5M8751_DA_AMIX1_SPK);

	reg_val = s5m8751_codec_read(codec, S5M8751_IN1_CTRL1);
	reg_val &= ~S5M8751_LOGIC_PDN;
	s5m8751_codec_write(codec, S5M8751_IN1_CTRL1, reg_val);
	reg_val |= S5M8751_LOGIC_PDN;
	s5m8751_codec_write(codec, S5M8751_IN1_CTRL1, reg_val);

	s5m8751_codec_write(codec, S5M8751_DA_VOLL, pdata->dac_vol);
	s5m8751_codec_write(codec, S5M8751_DA_VOLR, pdata->dac_vol);
	s5m8751_codec_write(codec, S5M8751_HP_VOL1, pdata->hp_vol);
	s5m8751_codec_write(codec, S5M8751_HP_VOL2, pdata->hp_vol);
	s5m8751_codec_write(codec, S5M8751_AMP_EN, S5M8751_SPK_AMP_EN);

	codec->dev = &pdev->dev;
	s5m8751_dai.dev = codec->dev;

	s5m8751_set_bias_level(codec, SND_SOC_BIAS_STANDBY);

	s5m8751_codec = codec;

	ret = snd_soc_register_codec(codec);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to register codec: %d\n", ret);
		goto err_codec;
	}

	ret = snd_soc_register_dais(&s5m8751_dai, 1);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to register DAI: %d\n", ret);
		goto err_codec;
	}

	return 0;

err_codec:
	snd_soc_unregister_codec(codec);

err:
	kfree(priv);
	return ret;
}

开发者ID:FrozenData，项目名称:SGS2-Kernel-Update2，代码行数:86，代码来源:s5m8751.c

示例11: dfbmcs320_probe

static int __devinit dfbmcs320_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev, &soc_codec_dev_dfbmcs320,
			&dfbmcs320_dai, 1);
}

开发者ID:1yankeedt，项目名称:D710BST_FL24_Kernel，代码行数:5，代码来源:dfbmcs320.c

示例12: wm8903_i2c_probe

static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
				      const struct i2c_device_id *id)
{
	struct wm8903_priv *wm8903;
	struct snd_soc_codec *codec;
	int ret;
	u16 val;

	wm8903 = kzalloc(sizeof(struct wm8903_priv), GFP_KERNEL);
	if (wm8903 == NULL)
		return -ENOMEM;

	codec = &wm8903->codec;

	mutex_init(&codec->mutex);
	INIT_LIST_HEAD(&codec->dapm_widgets);
	INIT_LIST_HEAD(&codec->dapm_paths);

	codec->dev = &i2c->dev;
	codec->name = "WM8903";
	codec->owner = THIS_MODULE;
	codec->bias_level = SND_SOC_BIAS_OFF;
	codec->set_bias_level = wm8903_set_bias_level;
	codec->dai = &wm8903_dai;
	codec->num_dai = 1;
	codec->reg_cache_size = ARRAY_SIZE(wm8903->reg_cache);
	codec->reg_cache = &wm8903->reg_cache[0];
	codec->private_data = wm8903;
	codec->volatile_register = wm8903_volatile_register;

	i2c_set_clientdata(i2c, codec);
	codec->control_data = i2c;

	ret = snd_soc_codec_set_cache_io(codec, 8, 16, SND_SOC_I2C);
	if (ret != 0) {
		dev_err(&i2c->dev, "Failed to set cache I/O: %d\n", ret);
		goto err;
	}

	val = snd_soc_read(codec, WM8903_SW_RESET_AND_ID);
	if (val != wm8903_reg_defaults[WM8903_SW_RESET_AND_ID]) {
		dev_err(&i2c->dev,
			"Device with ID register %x is not a WM8903\n", val);
		return -ENODEV;
	}

	val = snd_soc_read(codec, WM8903_REVISION_NUMBER);
	dev_info(&i2c->dev, "WM8903 revision %d\n",
		 val & WM8903_CHIP_REV_MASK);

	wm8903_reset(codec);

	/* power on device */
	wm8903_set_bias_level(codec, SND_SOC_BIAS_STANDBY);

	/* Latch volume update bits */
	val = snd_soc_read(codec, WM8903_ADC_DIGITAL_VOLUME_LEFT);
	val |= WM8903_ADCVU;
	snd_soc_write(codec, WM8903_ADC_DIGITAL_VOLUME_LEFT, val);
	snd_soc_write(codec, WM8903_ADC_DIGITAL_VOLUME_RIGHT, val);

	val = snd_soc_read(codec, WM8903_DAC_DIGITAL_VOLUME_LEFT);
	val |= WM8903_DACVU;
	snd_soc_write(codec, WM8903_DAC_DIGITAL_VOLUME_LEFT, val);
	snd_soc_write(codec, WM8903_DAC_DIGITAL_VOLUME_RIGHT, val);

	val = snd_soc_read(codec, WM8903_ANALOGUE_OUT1_LEFT);
	val |= WM8903_HPOUTVU;
	snd_soc_write(codec, WM8903_ANALOGUE_OUT1_LEFT, val);
	snd_soc_write(codec, WM8903_ANALOGUE_OUT1_RIGHT, val);

	val = snd_soc_read(codec, WM8903_ANALOGUE_OUT2_LEFT);
	val |= WM8903_LINEOUTVU;
	snd_soc_write(codec, WM8903_ANALOGUE_OUT2_LEFT, val);
	snd_soc_write(codec, WM8903_ANALOGUE_OUT2_RIGHT, val);

	val = snd_soc_read(codec, WM8903_ANALOGUE_OUT3_LEFT);
	val |= WM8903_SPKVU;
	snd_soc_write(codec, WM8903_ANALOGUE_OUT3_LEFT, val);
	snd_soc_write(codec, WM8903_ANALOGUE_OUT3_RIGHT, val);

	/* Enable DAC soft mute by default */
	val = snd_soc_read(codec, WM8903_DAC_DIGITAL_1);
	val |= WM8903_DAC_MUTEMODE;
	snd_soc_write(codec, WM8903_DAC_DIGITAL_1, val);

	wm8903_dai.dev = &i2c->dev;
	wm8903_codec = codec;

	ret = snd_soc_register_codec(codec);
	if (ret != 0) {
		dev_err(&i2c->dev, "Failed to register codec: %d\n", ret);
		goto err;
	}

	ret = snd_soc_register_dai(&wm8903_dai);
	if (ret != 0) {
		dev_err(&i2c->dev, "Failed to register DAI: %d\n", ret);
		goto err_codec;
	}
//.........这里部分代码省略.........

开发者ID:A2109devs，项目名称:lenovo_a2109a_kernel，代码行数:101，代码来源:wm8903.c

示例13: tfa_dummy_platform_probe

static int tfa_dummy_platform_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev, &soc_codec_tfa_dummy,
					&tfa_dummy_dai, 1);
}

开发者ID:moonlightly，项目名称:NX523J_kernel，代码行数:5，代码来源:tfa_dummy.c

示例14: spdif_dit_probe

static int spdif_dit_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev, &soc_codec_spdif_dit,
			&dit_stub_dai, 1);
}

开发者ID:ANFS，项目名称:ANFS-kernel，代码行数:5，代码来源:spdif_transciever.c

示例15: cs42l73_i2c_probe

static int cs42l73_i2c_probe(struct i2c_client *i2c_client,
			     const struct i2c_device_id *id)
{
	struct cs42l73_private *cs42l73;
	struct cs42l73_platform_data *pdata = dev_get_platdata(&i2c_client->dev);
	int ret;
	unsigned int devid = 0;
	unsigned int reg;
	u32 val32;

	cs42l73 = devm_kzalloc(&i2c_client->dev, sizeof(struct cs42l73_private),
			       GFP_KERNEL);
	if (!cs42l73)
		return -ENOMEM;

	cs42l73->regmap = devm_regmap_init_i2c(i2c_client, &cs42l73_regmap);
	if (IS_ERR(cs42l73->regmap)) {
		ret = PTR_ERR(cs42l73->regmap);
		dev_err(&i2c_client->dev, "regmap_init() failed: %d\n", ret);
		return ret;
	}

	if (pdata) {
		cs42l73->pdata = *pdata;
	} else {
		pdata = devm_kzalloc(&i2c_client->dev,
				     sizeof(struct cs42l73_platform_data),
				GFP_KERNEL);
		if (!pdata) {
			dev_err(&i2c_client->dev, "could not allocate pdata\n");
			return -ENOMEM;
		}
		if (i2c_client->dev.of_node) {
			if (of_property_read_u32(i2c_client->dev.of_node,
				"chgfreq", &val32) >= 0)
				pdata->chgfreq = val32;
		}
		pdata->reset_gpio = of_get_named_gpio(i2c_client->dev.of_node,
						"reset-gpio", 0);
		cs42l73->pdata = *pdata;
	}

	i2c_set_clientdata(i2c_client, cs42l73);

	if (cs42l73->pdata.reset_gpio) {
		ret = devm_gpio_request_one(&i2c_client->dev,
					    cs42l73->pdata.reset_gpio,
					    GPIOF_OUT_INIT_HIGH,
					    "CS42L73 /RST");
		if (ret < 0) {
			dev_err(&i2c_client->dev, "Failed to request /RST %d: %d\n",
				cs42l73->pdata.reset_gpio, ret);
			return ret;
		}
		gpio_set_value_cansleep(cs42l73->pdata.reset_gpio, 0);
		gpio_set_value_cansleep(cs42l73->pdata.reset_gpio, 1);
	}

	regcache_cache_bypass(cs42l73->regmap, true);

	/* initialize codec */
	ret = regmap_read(cs42l73->regmap, CS42L73_DEVID_AB, &reg);
	devid = (reg & 0xFF) << 12;

	ret = regmap_read(cs42l73->regmap, CS42L73_DEVID_CD, &reg);
	devid |= (reg & 0xFF) << 4;

	ret = regmap_read(cs42l73->regmap, CS42L73_DEVID_E, &reg);
	devid |= (reg & 0xF0) >> 4;

	if (devid != CS42L73_DEVID) {
		ret = -ENODEV;
		dev_err(&i2c_client->dev,
			"CS42L73 Device ID (%X). Expected %X\n",
			devid, CS42L73_DEVID);
		return ret;
	}

	ret = regmap_read(cs42l73->regmap, CS42L73_REVID, &reg);
	if (ret < 0) {
		dev_err(&i2c_client->dev, "Get Revision ID failed\n");
		return ret;;
	}

	dev_info(&i2c_client->dev,
		 "Cirrus Logic CS42L73, Revision: %02X\n", reg & 0xFF);

	regcache_cache_bypass(cs42l73->regmap, false);

	ret =  snd_soc_register_codec(&i2c_client->dev,
			&soc_codec_dev_cs42l73, cs42l73_dai,
			ARRAY_SIZE(cs42l73_dai));
	if (ret < 0)
		return ret;
	return 0;
}

开发者ID:acton393，项目名称:linux，代码行数:96，代码来源:cs42l73.c

示例16: sndspdif_codec_probe

static int __devinit sndspdif_codec_probe(struct platform_device *pdev)
{
	return snd_soc_register_codec(&pdev->dev, &soc_codec_dev_sndspdif, &sndspdif_dai, 1);	
}

开发者ID:BPI-SINOVOIP，项目名称:BPI-M2-bsp，代码行数:4，代码来源:sndspdif.c

示例17: alc5632_i2c_probe

static __devinit int alc5632_i2c_probe(struct i2c_client *client,
				const struct i2c_device_id *id)
{
	struct alc5632_priv *alc5632;
	int ret, ret1, ret2;
	unsigned int vid1, vid2;

	alc5632 = devm_kzalloc(&client->dev,
			 sizeof(struct alc5632_priv), GFP_KERNEL);
	if (alc5632 == NULL)
		return -ENOMEM;

	i2c_set_clientdata(client, alc5632);

	alc5632->regmap = regmap_init_i2c(client, &alc5632_regmap);
	if (IS_ERR(alc5632->regmap)) {
		ret = PTR_ERR(alc5632->regmap);
		dev_err(&client->dev, "regmap_init() failed: %d\n", ret);
		return ret;
	}

	ret1 = regmap_read(alc5632->regmap, ALC5632_VENDOR_ID1, &vid1);
	ret2 = regmap_read(alc5632->regmap, ALC5632_VENDOR_ID2, &vid2);
	if (ret1 != 0 || ret2 != 0) {
		dev_err(&client->dev,
		"Failed to read chip ID: ret1=%d, ret2=%d\n", ret1, ret2);
		regmap_exit(alc5632->regmap);
		return -EIO;
	}

	vid2 >>= 8;

	if ((vid1 != 0x10EC) || (vid2 != id->driver_data)) {
		dev_err(&client->dev,
		"Device is not a ALC5632: VID1=0x%x, VID2=0x%x\n", vid1, vid2);
		regmap_exit(alc5632->regmap);
		return -EINVAL;
	}

	ret = alc5632_reset(alc5632->regmap);
	if (ret < 0) {
		dev_err(&client->dev, "Failed to issue reset\n");
		regmap_exit(alc5632->regmap);
		return ret;
	}

	alc5632->id = vid2;
	switch (alc5632->id) {
	case 0x5c:
		alc5632_dai.name = "alc5632-hifi";
		break;
	default:
		return -EINVAL;
	}

	ret = snd_soc_register_codec(&client->dev,
		&soc_codec_device_alc5632, &alc5632_dai, 1);

	if (ret < 0) {
		dev_err(&client->dev, "Failed to register codec: %d\n", ret);
		regmap_exit(alc5632->regmap);
		return ret;
	}

	return ret;
}

开发者ID:romanbb，项目名称:android_kernel_lge_d851，代码行数:66，代码来源:alc5632.c

示例18: wm8993_i2c_probe


//.........这里部分代码省略.........

	wm8993->hubs_data.hp_startup_mode = 1;
	wm8993->hubs_data.dcs_codes = -2;

	memcpy(wm8993->reg_cache, wm8993_reg_defaults,
	       sizeof(wm8993->reg_cache));

	ret = snd_soc_codec_set_cache_io(codec, 8, 16, SND_SOC_I2C);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to set cache I/O: %d\n", ret);
		goto err;
	}

	i2c_set_clientdata(i2c, wm8993);
	codec->control_data = i2c;
	wm8993_codec = codec;

	codec->dev = &i2c->dev;

	for (i = 0; i < ARRAY_SIZE(wm8993->supplies); i++)
		wm8993->supplies[i].supply = wm8993_supply_names[i];

	ret = regulator_bulk_get(codec->dev, ARRAY_SIZE(wm8993->supplies),
				 wm8993->supplies);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to request supplies: %d\n", ret);
		goto err;
	}

	ret = regulator_bulk_enable(ARRAY_SIZE(wm8993->supplies),
				    wm8993->supplies);
	if (ret != 0) {
		dev_err(codec->dev, "Failed to enable supplies: %d\n", ret);
		goto err_get;
	}

	val = snd_soc_read(codec, WM8993_SOFTWARE_RESET);
	if (val != wm8993_reg_defaults[WM8993_SOFTWARE_RESET]) {
		dev_err(codec->dev, "Invalid ID register value %x\n", val);
		ret = -EINVAL;
		goto err_enable;
	}

	ret = snd_soc_write(codec, WM8993_SOFTWARE_RESET, 0xffff);
	if (ret != 0)
		goto err_enable;

	codec->cache_only = 1;

	/* By default we're using the output mixers */
	wm8993->class_w_users = 2;

	/* Latch volume update bits and default ZC on */
	snd_soc_update_bits(codec, WM8993_RIGHT_DAC_DIGITAL_VOLUME,
			    WM8993_DAC_VU, WM8993_DAC_VU);
	snd_soc_update_bits(codec, WM8993_RIGHT_ADC_DIGITAL_VOLUME,
			    WM8993_ADC_VU, WM8993_ADC_VU);

	/* Manualy manage the HPOUT sequencing for independent stereo
	 * control. */
	snd_soc_update_bits(codec, WM8993_ANALOGUE_HP_0,
			    WM8993_HPOUT1_AUTO_PU, 0);

	/* Use automatic clock configuration */
	snd_soc_update_bits(codec, WM8993_CLOCKING_4, WM8993_SR_MODE, 0);

	wm_hubs_handle_analogue_pdata(codec, wm8993->pdata.lineout1_diff,
				      wm8993->pdata.lineout2_diff,
				      wm8993->pdata.lineout1fb,
				      wm8993->pdata.lineout2fb,
				      wm8993->pdata.jd_scthr,
				      wm8993->pdata.jd_thr,
				      wm8993->pdata.micbias1_lvl,
				      wm8993->pdata.micbias2_lvl);
			     
	ret = wm8993_set_bias_level(codec, SND_SOC_BIAS_STANDBY);
	if (ret != 0)
		goto err_enable;

	wm8993_dai.dev = codec->dev;

	ret = snd_soc_register_dai(&wm8993_dai);
	if (ret != 0)
		goto err_bias;

	ret = snd_soc_register_codec(codec);

	return 0;

err_bias:
	wm8993_set_bias_level(codec, SND_SOC_BIAS_OFF);
err_enable:
	regulator_bulk_disable(ARRAY_SIZE(wm8993->supplies), wm8993->supplies);
err_get:
	regulator_bulk_free(ARRAY_SIZE(wm8993->supplies), wm8993->supplies);
err:
	wm8993_codec = NULL;
	kfree(wm8993);
	return ret;
}

开发者ID:KaZoom，项目名称:buildroot-linux-kernel-m3，代码行数:101，代码来源:wm8993.c

示例19: tas5086_i2c_probe

static int tas5086_i2c_probe(struct i2c_client *i2c,
			     const struct i2c_device_id *id)
{
	struct tas5086_private *priv;
	struct device *dev = &i2c->dev;
	int gpio_nreset = -EINVAL;
	int i, ret;

	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
	if (!priv)
		return -ENOMEM;

	for (i = 0; i < ARRAY_SIZE(supply_names); i++)
		priv->supplies[i].supply = supply_names[i];

	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(priv->supplies),
				      priv->supplies);
	if (ret < 0) {
		dev_err(dev, "Failed to get regulators: %d\n", ret);
		return ret;
	}

	priv->regmap = devm_regmap_init(dev, NULL, i2c, &tas5086_regmap);
	if (IS_ERR(priv->regmap)) {
		ret = PTR_ERR(priv->regmap);
		dev_err(&i2c->dev, "Failed to create regmap: %d\n", ret);
		return ret;
	}

	i2c_set_clientdata(i2c, priv);

	if (of_match_device(of_match_ptr(tas5086_dt_ids), dev)) {
		struct device_node *of_node = dev->of_node;
		gpio_nreset = of_get_named_gpio(of_node, "reset-gpio", 0);
	}

	if (gpio_is_valid(gpio_nreset))
		if (devm_gpio_request(dev, gpio_nreset, "TAS5086 Reset"))
			gpio_nreset = -EINVAL;

	priv->gpio_nreset = gpio_nreset;

	ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies), priv->supplies);
	if (ret < 0) {
		dev_err(dev, "Failed to enable regulators: %d\n", ret);
		return ret;
	}

	tas5086_reset(priv);

	/* The TAS5086 always returns 0x03 in its TAS5086_DEV_ID register */
	ret = regmap_read(priv->regmap, TAS5086_DEV_ID, &i);
	if (ret == 0 && i != 0x3) {
		dev_err(dev,
			"Failed to identify TAS5086 codec (got %02x)\n", i);
		ret = -ENODEV;
	}

	/*
	 * The chip has been identified, so we can turn off the power
	 * again until the dai link is set up.
	 */
	regulator_bulk_disable(ARRAY_SIZE(priv->supplies), priv->supplies);

	if (ret == 0)
		ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_tas5086,
					     &tas5086_dai, 1);

	return ret;
}

开发者ID:19Dan01，项目名称:linux，代码行数:70，代码来源:tas5086.c

示例20: cs42l52_i2c_probe


//.........这里部分代码省略.........
	}
	if (pdata) {
		cs42l52->pdata = *pdata;
	} else {
		pdata = devm_kzalloc(&i2c_client->dev,
				     sizeof(struct cs42l52_platform_data),
				GFP_KERNEL);
		if (!pdata) {
			dev_err(&i2c_client->dev, "could not allocate pdata\n");
			return -ENOMEM;
		}
		if (i2c_client->dev.of_node) {
			if (of_property_read_bool(i2c_client->dev.of_node,
				"cirrus,mica-differential-cfg"))
				pdata->mica_diff_cfg = true;

			if (of_property_read_bool(i2c_client->dev.of_node,
				"cirrus,micb-differential-cfg"))
				pdata->micb_diff_cfg = true;

			if (of_property_read_u32(i2c_client->dev.of_node,
				"cirrus,micbias-lvl", &val32) >= 0)
				pdata->micbias_lvl = val32;

			if (of_property_read_u32(i2c_client->dev.of_node,
				"cirrus,chgfreq-divisor", &val32) >= 0)
				pdata->chgfreq = val32;

			pdata->reset_gpio =
				of_get_named_gpio(i2c_client->dev.of_node,
						"cirrus,reset-gpio", 0);
		}
		cs42l52->pdata = *pdata;
	}

	if (cs42l52->pdata.reset_gpio) {
		ret = devm_gpio_request_one(&i2c_client->dev,
					    cs42l52->pdata.reset_gpio,
					    GPIOF_OUT_INIT_HIGH,
					    "CS42L52 /RST");
		if (ret < 0) {
			dev_err(&i2c_client->dev, "Failed to request /RST %d: %d\n",
				cs42l52->pdata.reset_gpio, ret);
			return ret;
		}
		gpio_set_value_cansleep(cs42l52->pdata.reset_gpio, 0);
		gpio_set_value_cansleep(cs42l52->pdata.reset_gpio, 1);
	}

	i2c_set_clientdata(i2c_client, cs42l52);

	ret = regmap_register_patch(cs42l52->regmap, cs42l52_threshold_patch,
				    ARRAY_SIZE(cs42l52_threshold_patch));
	if (ret != 0)
		dev_warn(cs42l52->dev, "Failed to apply regmap patch: %d\n",
			 ret);

	ret = regmap_read(cs42l52->regmap, CS42L52_CHIP, &reg);
	devid = reg & CS42L52_CHIP_ID_MASK;
	if (devid != CS42L52_CHIP_ID) {
		ret = -ENODEV;
		dev_err(&i2c_client->dev,
			"CS42L52 Device ID (%X). Expected %X\n",
			devid, CS42L52_CHIP_ID);
		return ret;
	}

	dev_info(&i2c_client->dev, "Cirrus Logic CS42L52, Revision: %02X\n",
		 reg & CS42L52_CHIP_REV_MASK);

	/* Set Platform Data */
	if (cs42l52->pdata.mica_diff_cfg)
		regmap_update_bits(cs42l52->regmap, CS42L52_MICA_CTL,
				   CS42L52_MIC_CTL_TYPE_MASK,
				cs42l52->pdata.mica_diff_cfg <<
				CS42L52_MIC_CTL_TYPE_SHIFT);

	if (cs42l52->pdata.micb_diff_cfg)
		regmap_update_bits(cs42l52->regmap, CS42L52_MICB_CTL,
				   CS42L52_MIC_CTL_TYPE_MASK,
				cs42l52->pdata.micb_diff_cfg <<
				CS42L52_MIC_CTL_TYPE_SHIFT);

	if (cs42l52->pdata.chgfreq)
		regmap_update_bits(cs42l52->regmap, CS42L52_CHARGE_PUMP,
				   CS42L52_CHARGE_PUMP_MASK,
				cs42l52->pdata.chgfreq <<
				CS42L52_CHARGE_PUMP_SHIFT);

	if (cs42l52->pdata.micbias_lvl)
		regmap_update_bits(cs42l52->regmap, CS42L52_IFACE_CTL2,
				   CS42L52_IFACE_CTL2_BIAS_LVL,
				cs42l52->pdata.micbias_lvl);

	ret =  snd_soc_register_codec(&i2c_client->dev,
			&soc_codec_dev_cs42l52, &cs42l52_dai, 1);
	if (ret < 0)
		return ret;
	return 0;
}

开发者ID:MaxChina，项目名称:linux，代码行数:101，代码来源:cs42l52.c

注：本文中的snd_soc_register_codec函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ snd_soc_register_component函数代码示例发布时间：2022-05-30

C++ snd_soc_register_card函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19131|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9972|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8317|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8686|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8627|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9643|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8611|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7991|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8642|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7527|2022-11-06

客服电话

电子邮件

C++ snd_soc_register_codec函数代码示例

示例1: gbcodec_i2c_probe

示例2: adau1701_i2c_probe

示例3: wm2000_i2c_probe

示例4: ac97_probe

示例5: wm8961_register

示例6: wm8523_register

示例7: cg29xx_codec_driver_probe

示例8: cq93vc_platform_probe

示例9: uda134x_codec_probe

示例10: s5m8751_codec_probe

示例11: dfbmcs320_probe

示例12: wm8903_i2c_probe

示例13: tfa_dummy_platform_probe

示例14: spdif_dit_probe

示例15: cs42l73_i2c_probe

示例16: sndspdif_codec_probe

示例17: alc5632_i2c_probe

示例18: wm8993_i2c_probe

示例19: tas5086_i2c_probe

示例20: cs42l52_i2c_probe

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

joaomh/curso-de-matlab

断牙刷新位置时间（断牙属性及刷新位置介绍

MATLAB 常用操作命令和快捷键 - 躬耕南阳

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053