C++ sil_wrw_mem函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中sil_wrw_mem函数的典型用法代码示例。如果您正苦于以下问题：C++ sil_wrw_mem函数的具体用法？C++ sil_wrw_mem怎么用？C++ sil_wrw_mem使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了sil_wrw_mem函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: target_timer_initialize

/*
 *  タイマの起動処理
 */
void
target_timer_initialize(intptr_t exinf)
{
	CLOCK    cyc;
	uint32_t tmp;

#ifdef SYSTIC_USE_CALIBRATION
	/* CALIBRATIONレジスタの値を使用 */
	cyc = (sil_rew_mem((void *)SYSTIC_CALIBRATION) & SYSTIC_TENMS) / 10;
#else 
	cyc = TO_CLOCK(TIC_NUME, TIC_DENO) - 1;
#endif /* SYSTIC_USE_CALIBRATION */

	/* 停止 */
	tmp = sil_rew_mem((void *)SYSTIC_CONTROL_STATUS);
	tmp &= ~SYSTIC_ENABLE;
	sil_wrw_mem((void *)SYSTIC_CONTROL_STATUS, tmp);

	sil_wrw_mem((void *)SYSTIC_RELOAD_VALUE, cyc);
	sil_wrw_mem((void *)SYSTIC_CURRENT_VALUE, cyc);

	tmp = sil_rew_mem((void *)SYSTIC_CONTROL_STATUS);

#ifdef SYSTIC_USE_STCLK
	/* 外部クロックの使用 */
	tmp |= SYSTIC_ENABLE;
#else
	/* プロセッサクロックの使用 */
	tmp |= SYSTIC_ENABLE|SYSTIC_CLKSOURCE;
#endif /* SYSTIC_USE_STCLK */

	sil_wrw_mem((void *)SYSTIC_CONTROL_STATUS, tmp);
}

开发者ID:huchunxu，项目名称:asp，代码行数:36，代码来源:prc_timer.c

示例2: at91skyeye_init_uart

void
at91skyeye_init_uart(void)
{
    /* 受信データの格納先アドレスの設定 */
    sil_wrw_mem((void *)(USART0_RPR), (uint32_t)(&usart_rev_buf));
    sil_wrw_mem((void *)(USART0_RCR), 0x0001);
}

开发者ID:duanlv，项目名称:asp-gr_peach_gcc-mbed，代码行数:7，代码来源:target_serial.c

示例3: target_initialize

/*
 *  ターゲット依存の初期化
 */
void
target_initialize(void)
{
	uint32_t	reg;

	/*
	 *  チップ依存の初期化
	 */
	chip_initialize();
	
	/*
	 *  Emulation Baseboardの割込みモードの設定
	 */
	sil_wrw_mem(EB_SYS_LOCK, EB_SYS_LOCK_UNLOCK);	/* ロック解除 */

	reg = sil_rew_mem(EB_SYS_PLD_CTRL1);
	reg &= ~EB_SYS_PLD_CTRL1_INTMODE_MASK;
	reg |= EB_SYS_PLD_CTRL1_INTMODE_NEW_NODCC;
	sil_wrw_mem(EB_SYS_PLD_CTRL1, reg);

	sil_wrw_mem(EB_SYS_LOCK, EB_SYS_LOCK_LOCK);		/* ロック */
	
	/*
	 *  UARTを初期化
	 */
#ifndef TOPPERS_OMIT_TECS
	tPutLogCT11MPCore_initialize();
#endif /* TOPPERS_OMIT_TECS */
}

开发者ID:takeharukato，项目名称:asp3-aarch64，代码行数:32，代码来源:target_kernel_impl.c

示例4: gicc_initialize

/*
 *  CPUインタフェースの初期化
 */
void
gicc_initialize(void)
{
	/*
	 *  CPUインタフェースをディスエーブル
	 */
	sil_wrw_mem(GICC_CTLR, GICC_CTLR_DISABLE);

	/*
	 *  割込み優先度マスクを最低優先度に設定
	 */
	gicc_set_priority((GIC_PRI_LEVEL - 1) << GIC_PRI_SHIFT);

	/*
	 *  割込み優先度の全ビット有効に
	 */
	sil_wrw_mem(GICC_BPR, 0U);

	/*
	 *  アクティブな割込みがあれば，EOIによりクリアする
	 */
	sil_wrw_mem(GICC_EOIR, sil_rew_mem(GICC_IAR));

	/*
	 *  CPUインタフェースをイネーブル
	 */
#ifdef TOPPERS_SAFEG_SECURE
	sil_wrw_mem(GICC_CTLR, (GICC_CTLR_FIQEN|GICC_CTLR_ENABLEGRP1
												|GICC_CTLR_ENABLEGRP0));
#else /* TOPPERS_SAFEG_SECURE */
	sil_wrw_mem(GICC_CTLR, GICC_CTLR_ENABLE);
#endif /* TOPPERS_SAFEG_SECURE */
}

开发者ID:takeharukato，项目名称:asp3-aarch64，代码行数:36，代码来源:gic_kernel_impl.c

示例5: uart_opn_por

SIOPCB   *
uart_opn_por(ID siopid, VP_INT exinf){

    SIOPCB      *siopcb;
    const SIOPINIB  *siopinib;

    siopcb = get_siopcb(siopid);
    siopinib = siopcb->siopinib;

#ifndef USE_JTAG_UART		
//    sil_wrw_mem(UART_DIVISOR, UART_DIVISOR_VAL);
    sil_wrw_mem((VP)UART_STATUS, 0x00);
    
    /*
     *  受信割り込み許可
     */
    sil_wrw_mem((VP)UART_CONTROL, UART_STATUS_RRDY);
#else
	sil_wrw_mem((VP)JTAG_UART_CONTROL,JTAG_UART_CONTROL_RIE);
#endif /* USE_JTAG_UART	*/
	
    siopcb->exinf = exinf;
    siopcb->getready = siopcb->putready = FALSE;
    siopcb->openflag = TRUE;

    return(siopcb);
}

开发者ID:inouema，项目名称:toppers，代码行数:27，代码来源:nios2.c

示例6: set_port_pull

Inline void set_port_pull(uint32_t reg, uint_t p, bool_t up)
{
	if (up) {
		sil_wrw_mem((void*)GPIO_BSRR(reg), 0x01 << p);
	} else {
		sil_wrw_mem((void*)GPIO_BRR(reg), 0x01 << p);
	}
}

开发者ID:inouema，项目名称:toppers，代码行数:8，代码来源:target_config.c

示例7: Buzzer

void Buzzer(uint8_t buzzer)
{
	if (buzzer == BUZZER_ON){
		sil_wrw_mem((void *)FIO2SET0,sil_rew_mem((void *)FIO2SET0) | (0x1<<1) ); /*p2.0 high*/
	}else {
		sil_wrw_mem((void *)FIO2CLR0,sil_rew_mem((void *)FIO2CLR0) | (0x1<<1) ); /*p2.0 low*/
	}
}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:8，代码来源:target_hw.c

示例8: LED_Output

void LED_Output(uint8_t ledvalue)
{
	sil_wrw_mem((void *)FIO3SET2,(0xf0 & (ledvalue<<4)));
	sil_wrw_mem((void *)FIO3SET3,(0x0f & (ledvalue>>4)));

	sil_wrw_mem((void *)FIO3CLR2,(0xf0 & ((~ledvalue)<<4)));
	sil_wrw_mem((void *)FIO3CLR3,(0x0f & ((~ledvalue)>>4)));
}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:8，代码来源:target_hw.c

示例9: at91skyeye_init_uart

void
at91skyeye_init_uart(uint_t siopid)
{
	SIOPCB *p_siopcb = get_siopcb(siopid);
      
	/* 受信データの格納先アドレスの設定 */
	sil_wrw_mem((void *)(USART0_RPR), (uint32_t)(&(p_siopcb->usart_rev_buf)));
	sil_wrw_mem((void *)(USART0_RCR), 0x0001);
}

开发者ID:inouema，项目名称:toppers，代码行数:9，代码来源:target_serial.c

示例10: RTC_Start

ERCD RTC_Start(void)
{
	/*clear the interrupt bits must do this to let the alarm pin to be low*/
	sil_wrw_mem((void *)RTC_ILR, 0x7);
	/*enable rtc clock*/
	sil_wrw_mem((void *)RTC_CCR, 0x11);

    return ERCD_OK;
}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:9，代码来源:target_rtc.c

示例11: Buzzer_Init

void Buzzer_Init(void)
{
	sil_wrw_mem((void *)SCS,sil_rew_mem((void *)SCS)|0x00000001);                /*set GPIOx to use Fast I/O */
	sil_wrw_mem((void *)PINSEL10,0);                                             /*ETM interface is disabled. must set this*/

	sil_wrw_mem((void *)PINSEL4,sil_rew_mem((void *)PINSEL4) & (~(0x3<<2)) );    /*set GPIOx to use Fast I/O */
	sil_wrw_mem((void *)PINMODE4,sil_rew_mem((void *)PINMODE4) & (~(0x3<<2)) );  /*p2.0 pull up*/
	sil_wrw_mem((void *)FIO2DIR0,sil_rew_mem((void *)FIO2DIR0) | (0x1<<1) );     /*p2.0 output*/
}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:9，代码来源:target_hw.c

示例12: uart_putchar

/*                                                                            
 *  送信する文字の書き込み                                                    
 */
Inline void
uart_putchar(SIOPCB *siopcb, UB c)
{
#ifndef USE_JTAG_UART
	sil_wrw_mem((VP)UART_TXDATA, c);
#else
	sil_wrw_mem((VP)JTAG_UART_DATA,c);
#endif /* USE_JTAG_UART	*/
}

开发者ID:inouema，项目名称:toppers，代码行数:12，代码来源:nios2.c

示例13: pl310_init

void
pl310_init(uint32_t aux_val, uint32_t aux_mask)
{
	uint32_t tmp;
	uint32_t aux;
	uint32_t cache_id;
	uint32_t prefetch;
	uint32_t prefetch_val = 0;    
	uint32_t power;
	int ways;

	/* L2キャッシュがすでにオンになっているか確認する */
	tmp = sil_rew_mem((void*)(RMA1_L2CACHE_BASE + PL310_CTRL));

	/* L2キャッシュが無効の場合のみ初期化を実施する */
	if ( !(tmp & 1) ) {
		cache_id = sil_rew_mem((void*)(RMA1_L2CACHE_BASE + PL310_CACHE_ID));
		aux = sil_rew_mem((void*)(RMA1_L2CACHE_BASE + PL310_AUX_CTRL));
		prefetch = sil_rew_mem((void*)(RMA1_L2CACHE_BASE + PL310_PREFETCH_CTRL));
		power = sil_rew_mem((void*)(RMA1_L2CACHE_BASE + PL310_POWER_CTRL));

		if (aux & (1 << 16)) {
			ways = 16;
		}
		else {
			ways = 8;
		}

		aux_val |= 1 << 22;
        
		aux_val |= 1 << 29;
		prefetch_val |= 1 << 29;

		aux_val |= 1 << 28;
		prefetch_val |= 1 << 28;


		if ((cache_id & 0x3f) > 0x6) {
			prefetch_val |= 1 << 30;
		}
                
		pl310_way_mask = (1 << ways) - 1;

		aux &= aux_mask;
		aux |= aux_val;
		prefetch |= prefetch_val;

		sil_wrw_mem((void*)(RMA1_L2CACHE_BASE + PL310_AUX_CTRL), aux);
		sil_wrw_mem((void*)(RMA1_L2CACHE_BASE + PL310_PREFETCH_CTRL), prefetch);
		sil_wrw_mem((void*)(RMA1_L2CACHE_BASE + PL310_POWER_CTRL), power);
        
		pl310_inv_all();
        
		sil_wrw_mem((void*)(RMA1_L2CACHE_BASE + PL310_CTRL), 1);
	}    
}

开发者ID:takahashim，项目名称:asp_arch_arm_gcc，代码行数:56，代码来源:pl310.c

示例14: uart_getchar

/*
 *  受信した文字の取り出し
 */
Inline uint8_t
uart_getchar(SIOPCB *p_siopcb)
{
    char c;
     
    c = usart_rev_buf;
    sil_wrw_mem((void *)(p_siopcb->p_siopinib->us_rpr), (uint32_t)(&usart_rev_buf));
    sil_wrw_mem((void *)(p_siopcb->p_siopinib->us_rcr), 0x0001);
    
    return(c);
}

开发者ID:duanlv，项目名称:asp-gr_peach_gcc-mbed，代码行数:14，代码来源:target_serial.c

示例15: uart_cls_por

void
uart_cls_por(SIOPCB *siopcb){
#ifndef USE_JTAG_UART	
    /* 割込み禁止 */
    sil_wrw_mem((VP)UART_CONTROL, 0x00);
#else
	sil_wrw_mem((VP)JTAG_UART_CONTROL,0x00);
#endif /* USE_JTAG_UART	*/		
    siopcb->openflag = FALSE;
    siopcb->sendflag = FALSE;
}

开发者ID:inouema，项目名称:toppers，代码行数:11，代码来源:nios2.c

示例16: uart_disable_rcv

/*                                                                             
 *  受信割込み禁止                                                             
 */
Inline void
uart_disable_rcv(SIOPCB *siopcb)
{
#ifndef USE_JTAG_UART	
	sil_wrw_mem((VP)UART_CONTROL,
				sil_rew_mem((VP)UART_CONTROL)&~UART_STATUS_RRDY);
#else
	sil_wrw_mem((VP)JTAG_UART_CONTROL,
				sil_rew_mem((VP)JTAG_UART_CONTROL)&~JTAG_UART_CONTROL_RIE);
#endif /* USE_JTAG_UART	*/	
}

开发者ID:inouema，项目名称:toppers，代码行数:14，代码来源:nios2.c

示例17: UART_PrintChar

void  UART_PrintChar (uint8_t ch)
{
	#if  UART_PORT == 1
		while (!(sil_rew_mem((void *)U1LSR) & 0x20));  /* wait until U1THR is empty.*/
		sil_wrw_mem((void *)U1THR, ch);
	#elif UART_PORT == 0
		while (!(sil_rew_mem((void *)U0LSR) & 0x20));  /* wait until U1THR is empty.*/
		sil_wrw_mem((void *)U0THR, ch);
	#endif

}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:11，代码来源:target_uart.c

示例18: uart_disable_send

/*                                                                             
 *  送信割込み禁止                                                             
 */
Inline void
uart_disable_send(SIOPCB *siopcb)
{
#ifndef USE_JTAG_UART
	sil_wrw_mem((VP)UART_CONTROL,
				sil_rew_mem((VP)UART_CONTROL)&~UART_CONTROL_ITRD);
#else
	sil_wrw_mem((VP)JTAG_UART_CONTROL,
				sil_rew_mem((VP)JTAG_UART_CONTROL)&~JTAG_UART_CONTROL_WIE);
#endif /* USE_JTAG_UART	*/
}

开发者ID:inouema，项目名称:toppers，代码行数:14，代码来源:nios2.c

示例19: timer2_capinit

void timer2_capinit(void)
{
	sil_wrw_mem(PCONP,sil_rew_mem(PCONP)|(1<<22));/*power on timer2*/
	sil_wrw_mem(PCLKSEL1,(PCLKSEL1&(~(0x3<<12)))|(0x1<<12));/*pclk of timer is cclk*/
	sil_wrw_mem(PINSEL0,sil_rew_mem(PINSEL0)|(0x3<<8)); /*p0.4 as cap2*/
	sil_wrw_mem(T2PR,0);                      /*prescale counter is 0*/
    sil_wrw_mem(T2IR,0xff);                   /*reset the interrupts*/
    sil_wrw_mem(T2TCR,0x02);                   /*disable and reset counter*/
    sil_wrw_mem(T2CTCR,0x00);                 /*timer mode,capture on rising edge CAP2.0 for TIMER2*/
    sil_wrw_mem(T2MCR,0x00);                  /*disable match control*/
    sil_wrw_mem(T2CCR,0x05);                  /*capture rising and falling edge cr0 load TC and generate interrupt*/
    sil_wrw_mem(T2TCR,0x01);                   /*start counter*/
}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:13，代码来源:lpc2478_timer.c

示例20: LED_Init

void LED_Init(void)
{
	sil_wrw_mem((void *)SCS,sil_rew_mem((void *)SCS)|0x00000001);                /*set GPIOx to use Fast I/O */
	/* P3[20] - p3[27] =>LEDS as GPIOs*/
	sil_wrw_mem((void *)PINSEL7,sil_rew_mem((void *)PINSEL7)&0xff0000ff);

	/*select P320 - P327  pull_up*/
	sil_wrw_mem((void *)PINMODE7,sil_rew_mem((void *)PINSEL7)&0xff0000ff);

	/* P320-P327 as output */
	sil_wrw_mem((void *)FIO3DIR2,sil_rew_mem((void *)FIO3DIR2)|0x000000f0);
	sil_wrw_mem((void *)FIO3DIR3,sil_rew_mem((void *)FIO3DIR3)|0x0000000f);
}

开发者ID:arktur04，项目名称:lpc2478-icdev-makefile，代码行数:13，代码来源:target_hw.c

注：本文中的sil_wrw_mem函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。