C++ serial_omap_port_disable函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中serial_omap_port_disable函数的典型用法代码示例。如果您正苦于以下问题：C++ serial_omap_port_disable函数的具体用法？C++ serial_omap_port_disable怎么用？C++ serial_omap_port_disable使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了serial_omap_port_disable函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: serial_omap_stop_tx

static void serial_omap_stop_tx(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;

	if (up->use_dma &&
		up->uart_dma.tx_dma_channel != OMAP_UART_DMA_CH_FREE) {
		/*
		 * Check if dma is still active. If yes do nothing,
		 * return. Else stop dma
		 */
		if (omap_get_dma_active_status(up->uart_dma.tx_dma_channel))
			return;
		omap_stop_dma(up->uart_dma.tx_dma_channel);
		omap_free_dma(up->uart_dma.tx_dma_channel);
		up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
		serial_omap_port_disable(up);
	}

	serial_omap_port_enable(up);
	if (up->ier & UART_IER_THRI) {
		up->ier &= ~UART_IER_THRI;
		serial_out(up, UART_IER, up->ier);
	}

	serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:26，代码来源:omap-serial.c

示例2: serial_omap_irq

/**
 * serial_omap_irq() - This handles the interrupt from one port
 * @irq: uart port irq number
 * @dev_id: uart port info
 */
static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
{
	struct uart_omap_port *up = dev_id;
	unsigned int iir, lsr;
	unsigned int int_id;
	unsigned long flags;
	int ret = IRQ_HANDLED;
	u8 tx_fifo_lvl;

	serial_omap_port_enable(up);
	iir = serial_in(up, UART_IIR);
	if (iir & UART_IIR_NO_INT) {
		serial_omap_port_disable(up);
		return IRQ_NONE;
	}

	int_id = iir & UART_OMAP_IIR_ID;

	spin_lock_irqsave(&up->port.lock, flags);
	lsr = serial_in(up, UART_LSR);
	if (int_id == UART_IIR_RDI || int_id == UART_OMAP_IIR_RX_TIMEOUT ||
	    int_id == UART_IIR_RLSI) {
		if (!up->use_dma) {
			if (lsr & UART_LSR_DR)
				receive_chars(up, &lsr);
		} else {
			up->ier &= ~(UART_IER_RDI | UART_IER_RLSI);
			serial_out(up, UART_IER, up->ier);
			if ((serial_omap_start_rxdma(up) != 0) &&
					(lsr & UART_LSR_DR))
				receive_chars(up, &lsr);
		}
	}

	check_modem_status(up);
	if (int_id == UART_IIR_THRI) {
		tx_fifo_lvl = serial_in(up, UART_OMAP_TXFIFO_LVL);
		if (lsr & UART_LSR_THRE || tx_fifo_lvl < up->port.fifosize)
			transmit_chars(up, tx_fifo_lvl);
		else
			ret = IRQ_NONE;
	}

	spin_unlock_irqrestore(&up->port.lock, flags);
	serial_omap_port_disable(up);

	up->port_activity = jiffies;
	return ret;
}

开发者ID:kf-otterx，项目名称:kernel_omap_otter-common，代码行数:54，代码来源:omap-serial.c

示例3: serial_omap_pm

static void
serial_omap_pm(struct uart_port *port, unsigned int state,
	       unsigned int oldstate)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned char efr;
	unsigned char lcr;

	dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id);

	serial_omap_port_enable(up);
	lcr = serial_in(up, UART_LCR);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	efr = serial_in(up, UART_EFR);
	serial_out(up, UART_EFR, efr | UART_EFR_ECB);
	serial_out(up, UART_LCR, 0);

	serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	serial_out(up, UART_EFR, efr);
	serial_out(up, UART_LCR, lcr);
	if (state)
		pm_runtime_put_sync(&up->pdev->dev);
	else
		serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:26，代码来源:omap-serial.c

示例4: serial_omap_poll_put_char

static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;

	serial_omap_port_enable(up);
	wait_for_xmitr(up);
	serial_out(up, UART_TX, ch);
	serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:9，代码来源:omap-serial.c

示例5: serial_omap_enable_ms

static void serial_omap_enable_ms(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;

	dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->pdev->id);

	serial_omap_port_enable(up);
	up->ier |= UART_IER_MSI;
	serial_out(up, UART_IER, up->ier);
	serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:11，代码来源:omap-serial.c

示例6: serial_omap_stop_rxdma

static void serial_omap_stop_rxdma(struct uart_omap_port *up)
{
	if (up->uart_dma.rx_dma_used) {
		del_timer(&up->uart_dma.rx_timer);
		omap_stop_dma(up->uart_dma.rx_dma_channel);
		omap_free_dma(up->uart_dma.rx_dma_channel);
		up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
		up->uart_dma.rx_dma_used = false;
		serial_omap_port_disable(up);
	}
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:11，代码来源:omap-serial.c

示例7: serial_omap_stop_rx

static void serial_omap_stop_rx(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;

	serial_omap_port_enable(up);
	if (up->use_dma)
		serial_omap_stop_rxdma(up);
	up->ier &= ~UART_IER_RLSI;
	up->port.read_status_mask &= ~UART_LSR_DR;
	serial_out(up, UART_IER, up->ier);
	serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:12，代码来源:omap-serial.c

示例8: omap_uart_wake

int omap_uart_wake(u8 uart_num)
{
	if (uart_num > OMAP_MAX_HSUART_PORTS)
		return -ENODEV;

	if (!ui[uart_num - 1])
		return -ENODEV;

	serial_omap_port_enable(ui[uart_num - 1]);
	serial_omap_port_disable(ui[uart_num - 1]);

	return 0;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:13，代码来源:omap-serial.c

示例9: serial_omap_poll_get_char

static int serial_omap_poll_get_char(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned int status;

	serial_omap_port_enable(up);
	status = serial_in(up, UART_LSR);
	if (!(status & UART_LSR_DR))
		return NO_POLL_CHAR;

	status = serial_in(up, UART_RX);
	serial_omap_port_disable(up);
	return status;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:14，代码来源:omap-serial.c

示例10: serial_omap_tx_empty

//static unsigned int serial_omap_tx_empty(struct uart_port *port)
unsigned int serial_omap_tx_empty(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned long flags = 0;
	unsigned int ret = 0;

	serial_omap_port_enable(up);
	dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->pdev->id);
	spin_lock_irqsave(&up->port.lock, flags);
	ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
	spin_unlock_irqrestore(&up->port.lock, flags);
	serial_omap_port_disable(up);
	return ret;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:15，代码来源:omap-serial.c

示例11: omap_serial_ext_uart_disable

int omap_serial_ext_uart_disable(u8 port_id)
{
	struct uart_omap_port *up;
	int err = 0;

	if (port_id > OMAP_MAX_HSUART_PORTS) {
		pr_err("Invalid Port_id %d passed to %s\n", port_id, __func__);
		err = -ENODEV;
	} else {
		up = ui[port_id];
		serial_omap_port_disable(up);
	}
	return err;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:14，代码来源:omap-serial.c

示例12: serial_omap_break_ctl

static void serial_omap_break_ctl(struct uart_port *port, int break_state)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned long flags = 0;

	dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->pdev->id);
	serial_omap_port_enable(up);
	spin_lock_irqsave(&up->port.lock, flags);
	if (break_state == -1)
		up->lcr |= UART_LCR_SBC;
	else
		up->lcr &= ~UART_LCR_SBC;
	serial_out(up, UART_LCR, up->lcr);
	spin_unlock_irqrestore(&up->port.lock, flags);
	serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:16，代码来源:omap-serial.c

示例13: serial_omap_shutdown

static void serial_omap_shutdown(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned long flags = 0;

	dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->pdev->id);

	serial_omap_port_enable(up);
	/*
	 * Disable interrupts & wakeup events from this port
	 */
	up->ier = 0;
	up->wer_restore = 0;
	serial_out(up, UART_OMAP_WER, 0);
	serial_out(up, UART_IER, 0);

	spin_lock_irqsave(&up->port.lock, flags);
	up->port.mctrl &= ~TIOCM_OUT2;
	serial_omap_set_mctrl(&up->port, up->port.mctrl);
	spin_unlock_irqrestore(&up->port.lock, flags);

	/*
	 * Disable break condition and FIFOs
	 */
	serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
	serial_omap_clear_fifos(up);

	/*
	 * Read data port to reset things, and then free the irq
	 */
	if (serial_in(up, UART_LSR) & UART_LSR_DR)
		(void) serial_in(up, UART_RX);
	if (up->use_dma) {
		dma_free_coherent(up->port.dev,
			UART_XMIT_SIZE,	up->port.state->xmit.buf,
			up->uart_dma.tx_buf_dma_phys);
		up->port.state->xmit.buf = NULL;
		serial_omap_stop_rx(port);
		dma_free_coherent(up->port.dev,
			up->uart_dma.rx_buf_size, up->uart_dma.rx_buf,
			up->uart_dma.rx_buf_dma_phys);
		up->uart_dma.rx_buf = NULL;
	}
	serial_omap_port_disable(up);
	free_irq(up->port.irq, up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:46，代码来源:omap-serial.c

示例14: serial_omap_resume

static int serial_omap_resume(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	if (up) {
		uart_resume_port(&serial_omap_reg, &up->port);
		up->suspended = false;
        serial_omap_port_enable(up);//add enable and disable to make sure RTS state right after resume
        if (up->rts_mux_driver_control && up->rts_pullup_in_suspend) {
            omap_rts_mux_write(0, up->port.line);
            up->rts_pullup_in_suspend = 0;
        }
        serial_omap_port_disable(up);
	}

	return 0;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:17，代码来源:omap-serial.c

示例15: omap_uart_resume_idle

/* TBD: Should be removed once we irq-chaining mechanism in place */
u32 omap_uart_resume_idle()
{
	int i;
	u32 ret = 0;

	for (i = 0; i < OMAP_MAX_HSUART_PORTS; i++) {
		struct uart_omap_port *up = ui[i];

		if (!up)
			continue;

		if (up->chk_wakeup(up->pdev)) {
			serial_omap_port_enable(up);
			serial_omap_port_disable(up);
			ret++;
		}
	}
	return ret;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:20，代码来源:omap-serial.c

示例16: serial_omap_get_mctrl

static unsigned int serial_omap_get_mctrl(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned char status;
	unsigned int ret = 0;

	serial_omap_port_enable(up);
	status = check_modem_status(up);
	serial_omap_port_disable(up);

	dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->pdev->id);

	if (status & UART_MSR_DCD)
		ret |= TIOCM_CAR;
	if (status & UART_MSR_RI)
		ret |= TIOCM_RNG;
	if (status & UART_MSR_DSR)
		ret |= TIOCM_DSR;
	if (status & UART_MSR_CTS)
		ret |= TIOCM_CTS;
	return ret;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:22，代码来源:omap-serial.c

示例17: serial_omap_set_mctrl

//static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned char mcr = 0;

	dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->pdev->id);
	if (mctrl & TIOCM_RTS)
		mcr |= UART_MCR_RTS;
	if (mctrl & TIOCM_DTR)
		mcr |= UART_MCR_DTR;
	if (mctrl & TIOCM_OUT1)
		mcr |= UART_MCR_OUT1;
	if (mctrl & TIOCM_OUT2)
		mcr |= UART_MCR_OUT2;
	if (mctrl & TIOCM_LOOP)
		mcr |= UART_MCR_LOOP;

	serial_omap_port_enable(up);
	up->mcr = serial_in(up, UART_MCR);
	up->mcr |= mcr;
	serial_out(up, UART_MCR, up->mcr);
	serial_omap_port_disable(up);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:24，代码来源:omap-serial.c

示例18: serial_omap_set_termios


//.........这里部分代码省略.........
	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);

	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	up->mcr = serial_in(up, UART_MCR);
	serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
	/* FIFO ENABLE, DMA MODE */
	serial_out(up, UART_FCR, up->fcr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	if (up->use_dma) {
		if (up->errata & OMAP4_UART_ERRATA_i659_TX_THR) {
			serial_out(up, UART_MDR3, SET_DMA_TX_THRESHOLD);
			serial_out(up, UART_TX_DMA_THRESHOLD, TX_FIFO_THR_LVL);
		}

		serial_out(up, UART_TI752_TLR, 0);
		up->scr |= (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8);
	}

	serial_out(up, UART_OMAP_SCR, up->scr);
	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	serial_out(up, UART_MCR, up->mcr);

	/* Protocol, Baud Rate, and Interrupt Settings */
	if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
		omap_uart_mdr1_errataset(up, up->mdr1);
	else
		serial_out(up, UART_OMAP_MDR1, up->mdr1);

	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	up->efr = serial_in(up, UART_EFR);
	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);

	serial_out(up, UART_LCR, 0);
	serial_out(up, UART_IER, 0);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	serial_out(up, UART_DLL, up->dll);	/* LS of divisor */
	serial_out(up, UART_DLM, up->dlh);	/* MS of divisor */

	serial_out(up, UART_LCR, 0);
	serial_out(up, UART_IER, up->ier);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, cval);

	if (baud > 230400 && baud != 3000000)
		up->mdr1 = UART_OMAP_MDR1_13X_MODE;
	else
		up->mdr1 = UART_OMAP_MDR1_16X_MODE;

	if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
		omap_uart_mdr1_errataset(up, up->mdr1);
	else
		serial_out(up, UART_OMAP_MDR1, up->mdr1);

	/* Hardware Flow Control Configuration */

	if (termios->c_cflag & CRTSCTS) {
		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
		up->mcr = serial_in(up, UART_MCR);
		serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);

		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
		up->efr = serial_in(up, UART_EFR);
		serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
		serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);

		up->efr |= (UART_EFR_CTS | UART_EFR_RTS);
		serial_out(up, UART_EFR, up->efr); /* Enable AUTORTS and AUTOCTS */
		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
		up->mcr |= UART_MCR_RTS;
		serial_out(up, UART_MCR, up->mcr);
		serial_out(up, UART_LCR, cval);
	} else {
		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
		up->efr = serial_in(up, UART_EFR);
		up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS);
		serial_out(up, UART_EFR, up->efr); /* Disable AUTORTS and AUTOCTS */
		serial_out(up, UART_LCR, cval);
	}

	serial_omap_set_mctrl(&up->port, up->port.mctrl);
	/* Software Flow Control Configuration */
	serial_omap_configure_xonxoff(up, termios);

	/* Now we are ready for RX data: enable rts line */
#if 0
	if (up->rts_mux_driver_control && up->rts_pullup_in_suspend) {
		omap_rts_mux_write(0, up->port.line);
		up->rts_pullup_in_suspend = 0;
	}
#endif
	spin_unlock_irqrestore(&up->port.lock, flags);
	serial_omap_port_disable(up);
	dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->pdev->id);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:101，代码来源:omap-serial.c

示例19: serial_omap_startup

static int serial_omap_startup(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	unsigned long flags = 0;
	int retval;

	/*
	 * Allocate the IRQ
	 */
	retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags,
				up->name, up);
	if (retval)
		return retval;

	dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->pdev->id);

	serial_omap_port_enable(up);
	/*
	 * Clear the FIFO buffers and disable them.
	 * (they will be reenabled in set_termios())
	 */
	serial_omap_clear_fifos(up);
	/* For Hardware flow control */
	serial_out(up, UART_MCR, UART_MCR_RTS);
	up->mcr = serial_in(up, UART_MCR);

	/*
	 * Clear the interrupt registers.
	 */
	(void) serial_in(up, UART_LSR);
	if (serial_in(up, UART_LSR) & UART_LSR_DR)
		(void) serial_in(up, UART_RX);
	(void) serial_in(up, UART_IIR);
	//(void) serial_in(up, UART_MSR); //CTS status change before startup will be missed, no need  to clear

	/*
	 * Now, initialize the UART
	 */
	serial_out(up, UART_LCR, UART_LCR_WLEN8);
	spin_lock_irqsave(&up->port.lock, flags);
	/*
	 * Most PC uarts need OUT2 raised to enable interrupts.
	 */
	up->port.mctrl |= TIOCM_OUT2;
	serial_omap_set_mctrl(&up->port, up->port.mctrl);
	spin_unlock_irqrestore(&up->port.lock, flags);

	up->msr_saved_flags = 0;
	if (up->use_dma) {
		free_page((unsigned long)up->port.state->xmit.buf);
		up->port.state->xmit.buf = dma_alloc_coherent(NULL,
			UART_XMIT_SIZE,
			(dma_addr_t *)&(up->uart_dma.tx_buf_dma_phys),
			0);
		init_timer(&(up->uart_dma.rx_timer));
		up->uart_dma.rx_timer.function = serial_omap_rxdma_poll;
		up->uart_dma.rx_timer.data = up->pdev->id;
		/* Currently the buffer size is 4KB. Can increase it */
		up->uart_dma.rx_buf = dma_alloc_coherent(NULL,
			up->uart_dma.rx_buf_size,
			(dma_addr_t *)&(up->uart_dma.rx_buf_dma_phys), 0);
	}
	/*
	 * Finally, enable interrupts. Note: Modem status interrupts
	 * are set via set_termios(), which will be occurring imminently
	 * anyway, so we don't enable them here.
	 */
	up->ier = UART_IER_RLSI | UART_IER_RDI;
	serial_out(up, UART_IER, up->ier);

	/* Enable module level wake up */
	up->wer_restore = up->wer;
	serial_out(up, UART_OMAP_WER, up->wer);

	serial_omap_port_disable(up);
	up->port_activity = jiffies;
	return 0;
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:78，代码来源:omap-serial.c

示例20: serial_omap_start_tx

static void serial_omap_start_tx(struct uart_port *port)
{
	struct uart_omap_port *up = (struct uart_omap_port *)port;
	struct circ_buf *xmit;
	unsigned int start;
	int ret = 0;

	if (!up->use_dma) {
		serial_omap_port_enable(up);
		serial_omap_enable_ier_thri(up);
		serial_omap_port_disable(up);
		return;
	}

	if (up->uart_dma.tx_dma_used)
		return;

	xmit = &up->port.state->xmit;

	if (up->uart_dma.tx_dma_channel == OMAP_UART_DMA_CH_FREE) {
		serial_omap_port_enable(up);
		ret = omap_request_dma(up->uart_dma.uart_dma_tx,
				"UART Tx DMA",
				(void *)uart_tx_dma_callback, up,
				&(up->uart_dma.tx_dma_channel));

		if (ret < 0) {
			serial_omap_enable_ier_thri(up);
			return;
		}
	}
	spin_lock(&(up->uart_dma.tx_lock));
	up->uart_dma.tx_dma_used = true;
	spin_unlock(&(up->uart_dma.tx_lock));

	start = up->uart_dma.tx_buf_dma_phys +
				(xmit->tail & (UART_XMIT_SIZE - 1));

	up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
	/*
	 * It is a circular buffer. See if the buffer has wounded back.
	 * If yes it will have to be transferred in two separate dma
	 * transfers
	 */
	if (start + up->uart_dma.tx_buf_size >=
			up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
		up->uart_dma.tx_buf_size =
			(up->uart_dma.tx_buf_dma_phys +
			UART_XMIT_SIZE) - start;

	omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
				OMAP_DMA_AMODE_CONSTANT,
				up->uart_dma.uart_base, 0, 0);
	omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
				OMAP_DMA_AMODE_POST_INC, start, 0, 0);
	omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
				OMAP_DMA_DATA_TYPE_S8,
				up->uart_dma.tx_buf_size, 1,
				OMAP_DMA_SYNC_ELEMENT,
				up->uart_dma.uart_dma_tx, 0);
	/* FIXME: Cache maintenance needed here? */
	omap_start_dma(up->uart_dma.tx_dma_channel);
}

开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:63，代码来源:omap-serial.c

注：本文中的serial_omap_port_disable函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ serial_omap_port_enable函数代码示例发布时间：2022-05-30

C++ serial_line_init函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19155|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9981|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8320|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8690|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8632|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9649|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8615|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7994|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8647|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7530|2022-11-06

客服电话

电子邮件

C++ serial_omap_port_disable函数代码示例

示例1: serial_omap_stop_tx

示例2: serial_omap_irq

示例3: serial_omap_pm

示例4: serial_omap_poll_put_char

示例5: serial_omap_enable_ms

示例6: serial_omap_stop_rxdma

示例7: serial_omap_stop_rx

示例8: omap_uart_wake

示例9: serial_omap_poll_get_char

示例10: serial_omap_tx_empty

示例11: omap_serial_ext_uart_disable

示例12: serial_omap_break_ctl

示例13: serial_omap_shutdown

示例14: serial_omap_resume

示例15: omap_uart_resume_idle

示例16: serial_omap_get_mctrl

示例17: serial_omap_set_mctrl

示例18: serial_omap_set_termios

示例19: serial_omap_startup

示例20: serial_omap_start_tx

请发表评论

全部评论

上一篇：

下一篇：

CVE-2022-30791

solegalli/feature-selection-for-machine-

nvim-lualine/lualine.nvim: A blazing fas

kentcdodds/dom-testing-library-with-anyt

win7系统重装系统初始设置的操作方法

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053