本文整理汇总了C++中pxa_set_mci_info函数的典型用法代码示例。如果您正苦于以下问题：C++ pxa_set_mci_info函数的具体用法？C++ pxa_set_mci_info怎么用？C++ pxa_set_mci_info使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了pxa_set_mci_info函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: imote2_init
static void __init imote2_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(imote2_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
platform_add_devices(imote2_devices, ARRAY_SIZE(imote2_devices));
pxa2xx_set_spi_info(1, &pxa_ssp_master_0_info);
pxa2xx_set_spi_info(2, &pxa_ssp_master_1_info);
pxa2xx_set_spi_info(3, &pxa_ssp_master_2_info);
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
i2c_register_board_info(0, imote2_i2c_board_info,
ARRAY_SIZE(imote2_i2c_board_info));
i2c_register_board_info(1, imote2_pwr_i2c_board_info,
ARRAY_SIZE(imote2_pwr_i2c_board_info));
pxa27x_set_i2c_power_info(&i2c_pwr_pdata);
pxa_set_i2c_info(&i2c_pdata);
pxa_set_mci_info(&imote2_mci_platform_data);
pxa_set_udc_info(&imote2_udc_info);
}
开发者ID:Medvedroid，项目名称:OT_903D-kernel-2.6.35.7，代码行数:27，代码来源:imote2.c
示例2: mainstone_init
static void __init mainstone_init(void)
{
int SW7 = 0; /* FIXME: get from SCR (Mst doc section 3.2.1.1) */
mst_flash_data[0].width = (BOOT_DEF & 1) ? 2 : 4;
mst_flash_data[1].width = 4;
/* Compensate for SW7 which swaps the flash banks */
mst_flash_data[SW7].name = "processor-flash";
mst_flash_data[SW7 ^ 1].name = "mainboard-flash";
printk(KERN_NOTICE "Mainstone configured to boot from %s\n",
mst_flash_data[0].name);
/* system bus arbiter setting
* - Core_Park
* - LCD_wt:DMA_wt:CORE_Wt = 2:3:4
*/
ARB_CNTRL = ARB_CORE_PARK | 0x234;
/*
* On Mainstone, we route AC97_SYSCLK via GPIO45 to
* the audio daughter card
*/
pxa_gpio_mode(GPIO45_SYSCLK_AC97_MD);
GPSR(GPIO48_nPOE) =
GPIO_bit(GPIO48_nPOE) |
GPIO_bit(GPIO49_nPWE) |
GPIO_bit(GPIO50_nPIOR) |
GPIO_bit(GPIO51_nPIOW) |
GPIO_bit(GPIO85_nPCE_1) |
GPIO_bit(GPIO54_nPCE_2);
pxa_gpio_mode(GPIO48_nPOE_MD);
pxa_gpio_mode(GPIO49_nPWE_MD);
pxa_gpio_mode(GPIO50_nPIOR_MD);
pxa_gpio_mode(GPIO51_nPIOW_MD);
pxa_gpio_mode(GPIO85_nPCE_1_MD);
pxa_gpio_mode(GPIO54_nPCE_2_MD);
pxa_gpio_mode(GPIO79_pSKTSEL_MD);
pxa_gpio_mode(GPIO55_nPREG_MD);
pxa_gpio_mode(GPIO56_nPWAIT_MD);
pxa_gpio_mode(GPIO57_nIOIS16_MD);
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
/* reading Mainstone's "Virtual Configuration Register"
might be handy to select LCD type here */
if (0)
mainstone_pxafb_info.modes = &toshiba_ltm04c380k_mode;
else
mainstone_pxafb_info.modes = &toshiba_ltm035a776c_mode;
set_pxa_fb_info(&mainstone_pxafb_info);
pxa_set_mci_info(&mainstone_mci_platform_data);
pxa_set_ficp_info(&mainstone_ficp_platform_data);
pxa_set_ohci_info(&mainstone_ohci_platform_data);
}
开发者ID:PennPanda，项目名称:linux-repo，代码行数:60，代码来源:mainstone.c
示例3: poodle_init
static void __init poodle_init(void)
{
int ret = 0;
pm_power_off = poodle_poweroff;
arm_pm_restart = poodle_restart;
/* setup sleep mode values */
PWER = 0x00000002;
PFER = 0x00000000;
PRER = 0x00000002;
PGSR0 = 0x00008000;
PGSR1 = 0x003F0202;
PGSR2 = 0x0001C000;
PCFR |= PCFR_OPDE;
/* cpu initialize */
/* Pgsr Register */
PGSR0 = 0x0146dd80;
PGSR1 = 0x03bf0890;
PGSR2 = 0x0001c000;
/* Alternate Register */
GAFR0_L = 0x01001000;
GAFR0_U = 0x591a8010;
GAFR1_L = 0x900a8451;
GAFR1_U = 0xaaa5aaaa;
GAFR2_L = 0x8aaaaaaa;
GAFR2_U = 0x00000002;
/* Direction Register */
GPDR0 = 0xd3f0904c;
GPDR1 = 0xfcffb7d3;
GPDR2 = 0x0001ffff;
/* Output Register */
GPCR0 = 0x00000000;
GPCR1 = 0x00000000;
GPCR2 = 0x00000000;
GPSR0 = 0x00400000;
GPSR1 = 0x00000000;
GPSR2 = 0x00000000;
set_pxa_fb_parent(&poodle_locomo_device.dev);
set_pxa_fb_info(&poodle_fb_info);
pxa_gpio_mode(POODLE_GPIO_USB_PULLUP | GPIO_OUT);
pxa_gpio_mode(POODLE_GPIO_IR_ON | GPIO_OUT);
pxa_set_udc_info(&udc_info);
pxa_set_mci_info(&poodle_mci_platform_data);
pxa_set_ficp_info(&poodle_ficp_platform_data);
platform_scoop_config = &poodle_pcmcia_config;
ret = platform_add_devices(devices, ARRAY_SIZE(devices));
if (ret) {
printk(KERN_WARNING "poodle: Unable to register LoCoMo device\n");
}
corgi_ssp_set_machinfo(&poodle_ssp_machinfo);
}
开发者ID:Broadcom，项目名称:stblinux-2.6.18，代码行数:60，代码来源:poodle.c
示例4: pcm990_baseboard_init
/*
* system init for baseboard usage. Will be called by pcm027 init.
*
* Add platform devices present on this baseboard and init
* them from CPU side as far as required to use them later on
*/
void __init pcm990_baseboard_init(void)
{
/* register CPLD access */
iotable_init(pcm990_io_desc, ARRAY_SIZE(pcm990_io_desc));
/* register CPLD's IRQ controller */
pcm990_init_irq();
platform_device_register(&pxa27x_device_ac97);
/* MMC */
pxa_set_mci_info(&pcm990_mci_platform_data);
/* USB host */
pxa_set_ohci_info(&pcm990_ohci_platform_data);
pxa_set_i2c_info(NULL);
#if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE)
pxa_set_camera_info(&pcm990_pxacamera_platform_data);
i2c_register_board_info(0, pcm990_i2c_devices,
ARRAY_SIZE(pcm990_i2c_devices));
#endif
printk(KERN_INFO"PCM-990 Evaluation baseboard initialized\n");
}
开发者ID:274914765，项目名称:C，代码行数:33，代码来源:pcm990-baseboard.c
示例5: stargate2_init
static void __init stargate2_init(void)
{
/* This is probably a board specific hack as this must be set
prior to connecting the MFP stuff up. */
MECR &= ~MECR_NOS;
pxa2xx_mfp_config(ARRAY_AND_SIZE(stargate2_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
platform_add_devices(ARRAY_AND_SIZE(stargate2_devices));
pxa2xx_set_spi_info(1, &pxa_ssp_master_0_info);
pxa2xx_set_spi_info(2, &pxa_ssp_master_1_info);
pxa2xx_set_spi_info(3, &pxa_ssp_master_2_info);
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
i2c_register_board_info(0, ARRAY_AND_SIZE(stargate2_i2c_board_info));
i2c_register_board_info(1,
ARRAY_AND_SIZE(stargate2_pwr_i2c_board_info));
pxa27x_set_i2c_power_info(&i2c_pwr_pdata);
pxa_set_i2c_info(&i2c_pdata);
pxa_set_mci_info(&stargate2_mci_platform_data);
pxa_set_udc_info(&stargate2_udc_info);
stargate2_reset_bluetooth();
}
开发者ID:JamiLiang，项目名称:android_kernel_samsung_xcover，代码行数:31，代码来源:stargate2.c
示例6: lubbock_init
static void __init lubbock_init(void)
{
int flashboot = (LUB_CONF_SWITCHES & 1);
pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL);
pxa_set_udc_info(&udc_info);
pxa_set_fb_info(NULL, &sharp_lm8v31);
pxa_set_mci_info(&lubbock_mci_platform_data);
pxa_set_ficp_info(&lubbock_ficp_platform_data);
pxa_set_ac97_info(NULL);
lubbock_flash_data[0].width = lubbock_flash_data[1].width =
(__raw_readl(BOOT_DEF) & 1) ? 2 : 4;
/* Compensate for the nROMBT switch which swaps the flash banks */
printk(KERN_NOTICE "Lubbock configured to boot from %s (bank %d)\n",
flashboot?"Flash":"ROM", flashboot);
lubbock_flash_data[flashboot^1].name = "application-flash";
lubbock_flash_data[flashboot].name = "boot-rom";
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
pxa2xx_set_spi_info(1, &pxa_ssp_master_info);
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
开发者ID:08opt，项目名称:linux，代码行数:30，代码来源:lubbock.c
示例7: corgi_init
static void __init corgi_init(void)
{
pm_power_off = corgi_poweroff;
arm_pm_restart = corgi_restart;
/* setup sleep mode values */
PWER = 0x00000002;
PFER = 0x00000000;
PRER = 0x00000002;
PGSR0 = 0x0158C000;
PGSR1 = 0x00FF0080;
PGSR2 = 0x0001C004;
/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
PCFR |= PCFR_OPDE;
corgi_ssp_set_machinfo(&corgi_ssp_machinfo);
pxa_gpio_mode(CORGI_GPIO_IR_ON | GPIO_OUT);
pxa_gpio_mode(CORGI_GPIO_HSYNC | GPIO_IN);
pxa_set_udc_info(&udc_info);
pxa_set_mci_info(&corgi_mci_platform_data);
pxa_set_ficp_info(&corgi_ficp_platform_data);
platform_scoop_config = &corgi_pcmcia_config;
platform_add_devices(devices, ARRAY_SIZE(devices));
}
开发者ID:3sOx，项目名称:asuswrt-merlin，代码行数:28，代码来源:corgi.c
示例8: imote2_init
static void __init imote2_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(imote2_pin_config));
/* SPI chip select directions - all other directions should
* be handled by drivers.*/
gpio_direction_output(37, 0);
gpio_direction_output(24, 0);
gpio_direction_output(39, 0);
platform_add_devices(imote2_devices, ARRAY_SIZE(imote2_devices));
pxa2xx_set_spi_info(1, &pxa_ssp_master_0_info);
pxa2xx_set_spi_info(2, &pxa_ssp_master_1_info);
pxa2xx_set_spi_info(3, &pxa_ssp_master_2_info);
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
i2c_register_board_info(0, imote2_i2c_board_info,
ARRAY_SIZE(imote2_i2c_board_info));
i2c_register_board_info(1, imote2_pwr_i2c_board_info,
ARRAY_SIZE(imote2_pwr_i2c_board_info));
pxa27x_set_i2c_power_info(&i2c_pwr_pdata);
pxa_set_i2c_info(&i2c_pdata);
pxa_set_mci_info(&imote2_mci_platform_data);
pxa_set_udc_info(&imote2_udc_info);
}
开发者ID:linuxkrishna，项目名称:4pamo，代码行数:29，代码来源:imote2.c
示例9: zeus_init
static void __init zeus_init(void)
{
u16 dm9000_msc = 0xe279;
system_rev = __raw_readw(ZEUS_CPLD_VERSION);
pr_info("Zeus CPLD V%dI%d\n", (system_rev & 0xf0) >> 4, (system_rev & 0x0f));
/* Fix timings for dm9000s (CS1/CS2)*/
MSC0 = (MSC0 & 0xffff) | (dm9000_msc << 16);
MSC1 = (MSC1 & 0xffff0000) | dm9000_msc;
pm_power_off = zeus_power_off;
pxa2xx_mfp_config(ARRAY_AND_SIZE(zeus_pin_config));
platform_add_devices(zeus_devices, ARRAY_SIZE(zeus_devices));
pxa_set_ohci_info(&zeus_ohci_platform_data);
if (zeus_setup_fb_gpios())
pr_err("Failed to setup fb gpios\n");
else
set_pxa_fb_info(&zeus_fb_info);
pxa_set_mci_info(&zeus_mci_platform_data);
pxa_set_udc_info(&zeus_udc_info);
pxa_set_ac97_info(&zeus_ac97_info);
pxa_set_i2c_info(NULL);
i2c_register_board_info(0, ARRAY_AND_SIZE(zeus_i2c_devices));
}
开发者ID:Aircell，项目名称:asp-kernel，代码行数:30，代码来源:zeus.c
示例10: common_init
static void __init common_init(void)
{
pm_power_off = spitz_poweroff;
arm_pm_restart = spitz_restart;
PMCR = 0x00;
/* setup sleep mode values */
PWER = 0x00000002;
PFER = 0x00000000;
PRER = 0x00000002;
PGSR0 = 0x0158C000;
PGSR1 = 0x00FF0080;
PGSR2 = 0x0001C004;
/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
PCFR |= PCFR_OPDE;
corgi_ssp_set_machinfo(&spitz_ssp_machinfo);
pxa_gpio_mode(SPITZ_GPIO_HSYNC | GPIO_IN);
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_mci_info(&spitz_mci_platform_data);
pxa_set_ohci_info(&spitz_ohci_platform_data);
pxa_set_ficp_info(&spitz_ficp_platform_data);
set_pxa_fb_parent(&spitzssp_device.dev);
set_pxa_fb_info(&spitz_pxafb_info);
}
开发者ID:D-Land，项目名称:operating-systems，代码行数:29，代码来源:spitz.c
示例11: em_x270_init_mmc
static void __init em_x270_init_mmc(void)
{
if (machine_is_em_x270())
em_x270_mci_platform_data.get_ro = em_x270_mci_get_ro;
pxa_set_mci_info(&em_x270_mci_platform_data);
}
开发者ID:bitcubate，项目名称:linux-edison，代码行数:7，代码来源:em-x270.c
示例12: zylonite_init_mmc
static void __init zylonite_init_mmc(void)
{
pxa_set_mci_info(&zylonite_mci_platform_data);
pxa3xx_set_mci2_info(&zylonite_mci2_platform_data);
if (cpu_is_pxa310())
pxa3xx_set_mci3_info(&zylonite_mci3_platform_data);
}
开发者ID:303750856，项目名称:linux-3.1，代码行数:7，代码来源:zylonite.c
示例13: mioa701_machine_init
static void __init mioa701_machine_init(void)
{
PSLR = 0xff100000; /* SYSDEL=125ms, PWRDEL=125ms, PSLR_SL_ROD=1 */
PCFR = PCFR_DC_EN | PCFR_GPR_EN | PCFR_OPDE;
RTTR = 32768 - 1; /* Reset crazy WinCE value */
UP2OCR = UP2OCR_HXOE;
pxa2xx_mfp_config(ARRAY_AND_SIZE(mioa701_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
mio_gpio_request(ARRAY_AND_SIZE(global_gpios));
bootstrap_init();
pxa_set_fb_info(NULL, &mioa701_pxafb_info);
pxa_set_mci_info(&mioa701_mci_info);
pxa_set_keypad_info(&mioa701_keypad_info);
pxa_set_udc_info(&mioa701_udc_info);
pxa_set_ac97_info(&mioa701_ac97_info);
pm_power_off = mioa701_poweroff;
arm_pm_restart = mioa701_restart;
platform_add_devices(devices, ARRAY_SIZE(devices));
gsm_init();
i2c_register_board_info(1, ARRAY_AND_SIZE(mioa701_pi2c_devices));
pxa_set_i2c_info(&i2c_pdata);
pxa27x_set_i2c_power_info(NULL);
pxa_set_camera_info(&mioa701_pxacamera_platform_data);
}
开发者ID:0709oNEY，项目名称:at100-kernel，代码行数:28，代码来源:mioa701.c
示例14: tosa_init
static void __init tosa_init(void)
{
int dummy;
pxa2xx_mfp_config(ARRAY_AND_SIZE(tosa_pin_config));
gpio_set_wake(MFP_PIN_GPIO1, 1);
/* We can't pass to gpio-keys since it will drop the Reset altfunc */
init_gpio_reset(TOSA_GPIO_ON_RESET, 0);
pm_power_off = tosa_poweroff;
arm_pm_restart = tosa_restart;
PCFR |= PCFR_OPDE;
/* enable batt_fault */
PMCR = 0x01;
dummy = gpiochip_reserve(TOSA_SCOOP_GPIO_BASE, 12);
dummy = gpiochip_reserve(TOSA_SCOOP_JC_GPIO_BASE, 12);
dummy = gpiochip_reserve(TOSA_TC6393XB_GPIO_BASE, 16);
pxa_set_mci_info(&tosa_mci_platform_data);
pxa_set_udc_info(&udc_info);
pxa_set_ficp_info(&tosa_ficp_platform_data);
pxa_set_i2c_info(NULL);
platform_scoop_config = &tosa_pcmcia_config;
clk_add_alias("CLK_CK3P6MI", &tc6393xb_device.dev, "GPIO11_CLK", NULL);
platform_add_devices(devices, ARRAY_SIZE(devices));
}
开发者ID:caglar10ur，项目名称:linux-2.6.27.y，代码行数:32，代码来源:tosa.c
示例15: poodle_init
static void __init poodle_init(void)
{
int ret = 0;
pm_power_off = poodle_poweroff;
PCFR |= PCFR_OPDE;
pxa2xx_mfp_config(ARRAY_AND_SIZE(poodle_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
platform_scoop_config = &poodle_pcmcia_config;
ret = platform_add_devices(devices, ARRAY_SIZE(devices));
if (ret)
pr_warning("poodle: Unable to register LoCoMo device\n");
pxa_set_fb_info(&poodle_locomo_device.dev, &poodle_fb_info);
pxa_set_udc_info(&udc_info);
pxa_set_mci_info(&poodle_mci_platform_data);
pxa_set_ficp_info(&poodle_ficp_platform_data);
pxa_set_i2c_info(NULL);
i2c_register_board_info(0, ARRAY_AND_SIZE(poodle_i2c_devices));
poodle_init_spi();
}
开发者ID:01org，项目名称:XenGT-Preview-kernel，代码行数:28，代码来源:poodle.c
示例16: zylonite_init
static void __init zylonite_init(void)
{
/*
* Note: We depend that the bootloader set
* the correct value to MSC register for SMC91x.
*/
platform_device_register(&smc91x_device);
#ifdef CONFIG_FB_PXA
pxafb_detect_lcd_panel();
pxafb_config_lcd_panel();
#endif
#ifdef CONFIG_PXA_FICP
pxa_set_ficp_info(&zylonite_ficp_platform_data);
zylonite_enable_stuart_pins();
#endif
zylonite_enable_eth_pins();
zylonite_enable_i2c_pins();
zylonite_enable_keyp_pins();
zylonite_enable_ffuart_pins();
#ifdef CONFIG_MMC
pxa_set_mci_info(&zylonite_mci_platform_data);
#endif
}
开发者ID:JacksonZhangkun，项目名称:linux-2.6，代码行数:29，代码来源:zylonite.c
示例17: idp_init
static void __init idp_init(void)
{
printk("idp_init()\n");
platform_device_register(&smc91x_device);
//platform_device_register(&mst_audio_device);
set_pxa_fb_info(&sharp_lm8v31);
pxa_set_mci_info(&idp_mci_platform_data);
}
开发者ID:devicenull，项目名称:supermicro_ipmi_firmware，代码行数:9，代码来源:idp.c
示例18: palmz72_init
static void __init palmz72_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmz72_pin_config));
set_pxa_fb_info(&palmz72_lcd_screen);
pxa_set_mci_info(&palmz72_mci_platform_data);
pxa_set_ac97_info(NULL);
pxa_set_ficp_info(&palmz72_ficp_platform_data);
pxa_set_keypad_info(&palmz72_keypad_platform_data);
platform_add_devices(devices, ARRAY_SIZE(devices));
}
开发者ID:abgoyal，项目名称:entourage_edge_kernel，代码行数:10，代码来源:palmz72.c
示例19: palm27x_mmc_init
void __init palm27x_mmc_init(int detect, int ro, int power,
int power_inverted)
{
palm27x_mci_platform_data.gpio_card_detect = detect;
palm27x_mci_platform_data.gpio_card_ro = ro;
palm27x_mci_platform_data.gpio_power = power;
palm27x_mci_platform_data.gpio_power_invert = power_inverted;
pxa_set_mci_info(&palm27x_mci_platform_data);
}
开发者ID:03199618，项目名称:linux，代码行数:10，代码来源:palm27x.c
示例20: treo680_init
static void __init treo680_init(void)
{
treo_init();
pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
pxa_set_mci_info(&treo680_mci_platform_data);
pxa_set_keypad_info(&treo680_keypad_platform_data);
pxa_set_ohci_info(&treo680_ohci_info);
platform_add_devices(ARRAY_AND_SIZE(treo680_devices));
}
开发者ID:GNUtoo，项目名称:bug20-2.6.35-linaro，代码行数:10，代码来源:palmtreo.c
注：本文中的pxa_set_mci_info函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。 |
客服电话
APP下载
官方微信
请发表评论