C++ px4_ioctl函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中px4_ioctl函数的典型用法代码示例。如果您正苦于以下问题：C++ px4_ioctl函数的具体用法？C++ px4_ioctl怎么用？C++ px4_ioctl使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了px4_ioctl函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: px4_open

/**
* Disable all multirotor motors when in fw mode.
*/
void
Standard::set_max_mc(unsigned pwm_value)
{
	int ret;
	unsigned servo_count;
	const char *dev = PWM_OUTPUT0_DEVICE_PATH;
	int fd = px4_open(dev, 0);

	if (fd < 0) {
		PX4_WARN("can't open %s", dev);
	}

	ret = px4_ioctl(fd, PWM_SERVO_GET_COUNT, (unsigned long)&servo_count);
	struct pwm_output_values pwm_values;
	memset(&pwm_values, 0, sizeof(pwm_values));

	for (int i = 0; i < _params->vtol_motor_count; i++) {
		pwm_values.values[i] = pwm_value;
		pwm_values.channel_count = _params->vtol_motor_count;
	}

	ret = px4_ioctl(fd, PWM_SERVO_SET_MAX_PWM, (long unsigned int)&pwm_values);

	if (ret != OK) {
		PX4_WARN("failed setting max values");
	}

	px4_close(fd);
}

开发者ID:DonLakeFlyer，项目名称:Firmware，代码行数:32，代码来源:standard.cpp

示例2: px4_open

/**
* Adjust idle speed for mc mode.
*/
void VtolType::set_idle_mc()
{
	const char *dev = PWM_OUTPUT0_DEVICE_PATH;
	int fd = px4_open(dev, 0);

	if (fd < 0) {
		PX4_WARN("can't open %s", dev);
	}

	unsigned servo_count;
	int ret = px4_ioctl(fd, PWM_SERVO_GET_COUNT, (unsigned long)&servo_count);
	unsigned pwm_value = _params->idle_pwm_mc;
	struct pwm_output_values pwm_values;
	memset(&pwm_values, 0, sizeof(pwm_values));

	for (int i = 0; i < _params->vtol_motor_count; i++) {
		pwm_values.values[i] = pwm_value;
		pwm_values.channel_count++;
	}

	ret = px4_ioctl(fd, PWM_SERVO_SET_MIN_PWM, (long unsigned int)&pwm_values);

	if (ret != OK) {
		PX4_WARN("failed setting min values");
	}

	px4_close(fd);

	flag_idle_mc = true;
}

开发者ID:AlexanderAurora，项目名称:Firmware，代码行数:33，代码来源:vtol_type.cpp

示例3: reset

/**
 * @brief Resets the driver.
 */
void
reset()
{
	if (!instance) {
		PX4_WARN("No ll40ls driver running");
		return;
	}

	int fd = px4_open(instance->get_dev_name(), O_RDONLY);

	if (fd < 0) {
		PX4_ERR("Error opening fd");
		return;
	}

	if (px4_ioctl(fd, SENSORIOCRESET, 0) < 0) {
		PX4_ERR("driver reset failed");
		px4_close(fd);
		return;
	}

	if (px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT) < 0) {
		PX4_ERR("driver poll restart failed");
		px4_close(fd);
		return;
	}
}

开发者ID:AlexisTM，项目名称:Firmware，代码行数:30，代码来源:ll40ls.cpp

示例4: px4_open

bool VtolType::apply_pwm_limits(struct pwm_output_values &pwm_values, pwm_limit_type type)
{
	const char *dev = PWM_OUTPUT0_DEVICE_PATH;
	int fd = px4_open(dev, 0);

	if (fd < 0) {
		PX4_WARN("can't open %s", dev);
		return false;
	}

	int ret;

	if (type == pwm_limit_type::TYPE_MINIMUM) {
		ret = px4_ioctl(fd, PWM_SERVO_SET_MIN_PWM, (long unsigned int)&pwm_values);

	} else {
		ret = px4_ioctl(fd, PWM_SERVO_SET_MAX_PWM, (long unsigned int)&pwm_values);
	}

	px4_close(fd);


	if (ret != OK) {
		PX4_ERR("failed setting max values");
		return false;
	}

	return true;
}

开发者ID:alsaibie，项目名称:Firmware_Dolphin，代码行数:29，代码来源:vtol_type.cpp

示例5: load

static int
load(const char *devname, const char *fname)
{
	// sleep a while to ensure device has been set up
	usleep(20000);
	
	int		dev;
	char		buf[2048];

	/* open the device */
	if ((dev = px4_open(devname, 0)) < 0) {
		warnx("can't open %s\n", devname);
		return 1;
	}

	/* reset mixers on the device */
	if (px4_ioctl(dev, MIXERIOCRESET, 0)) {
		warnx("can't reset mixers on %s", devname);
		return 1;
	}

	if (load_mixer_file(fname, &buf[0], sizeof(buf)) < 0) {
		warnx("can't load mixer: %s", fname);
		return 1;
	}

	/* XXX pass the buffer to the device */
	int ret = px4_ioctl(dev, MIXERIOCLOADBUF, (unsigned long)buf);

	if (ret < 0) {
		warnx("error loading mixers from %s", fname);
		return 1;
	}
	return 0;
}

开发者ID:Nitaym，项目名称:Firmware，代码行数:35，代码来源:mixer.cpp

示例6: test_gpio

int test_gpio(int argc, char *argv[])
{
	int		ret = 0;

#ifdef PX4IO_DEVICE_PATH

	int fd = px4_open(PX4IO_DEVICE_PATH, 0);

	if (fd < 0) {
		printf("GPIO: open fail\n");
		return ERROR;
	}

	/* set all GPIOs to default state */
	px4_ioctl(fd, GPIO_RESET, ~0);


	/* XXX need to add some GPIO waving stuff here */


	/* Go back to default */
	px4_ioctl(fd, GPIO_RESET, ~0);

	px4_close(fd);
	printf("\t GPIO test successful.\n");

#endif


	return ret;
}

开发者ID:1002victor，项目名称:Firmware，代码行数:31，代码来源:test_gpio.c

示例7: test

/**
 * Perform some basic functional tests on the driver;
 * make sure we can collect data from the sensor in polled
 * and automatic modes.
 */
void
test()
{
	struct differential_pressure_s report;
	ssize_t sz;
	int ret;

	int fd = px4_open(ETS_PATH, O_RDONLY);

	if (fd < 0) {
		PX4_ERR("%s open failed (try 'ets_airspeed start' if the driver is not running", ETS_PATH);
	}

	/* do a simple demand read */
	sz = px4_read(fd, &report, sizeof(report));

	if (sz != sizeof(report)) {
		PX4_ERR("immediate read failed");
	}

	PX4_INFO("single read");
	PX4_INFO("diff pressure: %f pa", (double)report.differential_pressure_filtered_pa);

	/* start the sensor polling at 2Hz */
	if (OK != px4_ioctl(fd, SENSORIOCSPOLLRATE, 2)) {
		PX4_ERR("failed to set 2Hz poll rate");
	}

	/* read the sensor 5x and report each value */
	for (unsigned i = 0; i < 5; i++) {
		struct pollfd fds;

		/* wait for data to be ready */
		fds.fd = fd;
		fds.events = POLLIN;
		ret = poll(&fds, 1, 2000);

		if (ret != 1) {
			PX4_ERR("timed out waiting for sensor data");
		}

		/* now go get it */
		sz = px4_read(fd, &report, sizeof(report));

		if (sz != sizeof(report)) {
			err(1, "periodic read failed");
		}

		PX4_INFO("periodic read %u", i);
		PX4_INFO("diff pressure: %f pa", (double)report.differential_pressure_filtered_pa);
	}

	/* reset the sensor polling to its default rate */
	if (OK != px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT)) {
		PX4_ERR("failed to set default rate");
	}

	errx(0, "PASS");
}

开发者ID:Kumru，项目名称:Firmware，代码行数:64，代码来源:ets_airspeed.cpp

示例8: test

/**
 * Perform some basic functional tests on the driver;
 * make sure we can collect data from the sensor in polled
 * and automatic modes.
 */
void
test()
{
	struct distance_sensor_s report;
	ssize_t sz;

	int fd = px4_open(RANGE_FINDER0_DEVICE_PATH, O_RDONLY);

	if (fd < 0) {
		err(1, "%s open failed (try 'tfmini start' if the driver is not running", RANGE_FINDER0_DEVICE_PATH);
	}

	/* do a simple demand read */
	sz = px4_read(fd, &report, sizeof(report));

	if (sz != sizeof(report)) {
		err(1, "immediate read failed");
	}

	print_message(report);

	/* start the sensor polling at 2 Hz rate */
	if (OK != px4_ioctl(fd, SENSORIOCSPOLLRATE, 2)) {
		errx(1, "failed to set 2Hz poll rate");
	}

	/* read the sensor 5x and report each value */
	for (unsigned i = 0; i < 5; i++) {
		px4_pollfd_struct_t fds{};

		/* wait for data to be ready */
		fds.fd = fd;
		fds.events = POLLIN;
		int ret = px4_poll(&fds, 1, 2000);

		if (ret != 1) {
			warnx("timed out");
			break;
		}

		/* now go get it */
		sz = px4_read(fd, &report, sizeof(report));

		if (sz != sizeof(report)) {
			warnx("read failed: got %d vs exp. %d", sz, sizeof(report));
			break;
		}

		print_message(report);
	}

	/* reset the sensor polling to the default rate */
	if (OK != px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT)) {
		errx(1, "ERR: DEF RATE");
	}

	errx(0, "PASS");
}

开发者ID:ayu135，项目名称:Firmware，代码行数:63，代码来源:tfmini.cpp

示例9: test

// perform some basic functional tests on the driver;
// make sure we can collect data from the sensor in polled
// and automatic modes.
void test()
{
	int fd = px4_open(PATH_MS5525, O_RDONLY);

	if (fd < 0) {
		PX4_WARN("%s open failed (try 'ms5525_airspeed start' if the driver is not running", PATH_MS5525);
		return;
	}

	// do a simple demand read
	differential_pressure_s report;
	ssize_t sz = px4_read(fd, &report, sizeof(report));

	if (sz != sizeof(report)) {
		PX4_WARN("immediate read failed");
		return;
	}

	PX4_WARN("single read");
	PX4_WARN("diff pressure: %d pa", (int)report.differential_pressure_filtered_pa);

	/* start the sensor polling at 2Hz */
	if (OK != px4_ioctl(fd, SENSORIOCSPOLLRATE, 2)) {
		PX4_WARN("failed to set 2Hz poll rate");
		return;
	}

	/* read the sensor 5x and report each value */
	for (unsigned i = 0; i < 5; i++) {
		px4_pollfd_struct_t fds;

		/* wait for data to be ready */
		fds.fd = fd;
		fds.events = POLLIN;
		int ret = px4_poll(&fds, 1, 2000);

		if (ret != 1) {
			PX4_ERR("timed out");
		}

		/* now go get it */
		sz = px4_read(fd, &report, sizeof(report));

		if (sz != sizeof(report)) {
			PX4_ERR("periodic read failed");
		}

		PX4_WARN("periodic read %u", i);
		PX4_WARN("diff pressure: %d pa", (int)report.differential_pressure_filtered_pa);
		PX4_WARN("temperature: %d C (0x%02x)", (int)report.temperature, (unsigned) report.temperature);
	}

	/* reset the sensor polling to its default rate */
	if (PX4_OK != px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT)) {
		PX4_WARN("failed to set default rate");
	}
}

开发者ID:Kumru，项目名称:Firmware，代码行数:60，代码来源:MS5525_main.cpp

示例10: test_tone

int test_tone(int argc, char *argv[])
{
	int fd, result;
	unsigned long tone;

	fd = px4_open(TONEALARM0_DEVICE_PATH, O_WRONLY);

	if (fd < 0) {
		printf("failed opening " TONEALARM0_DEVICE_PATH "\n");
		goto out;
	}

	tone = 1;

	if (argc == 2) {
		tone = atoi(argv[1]);
	}

	if (tone  == 0) {
		result = px4_ioctl(fd, TONE_SET_ALARM, TONE_STOP_TUNE);

		if (result < 0) {
			printf("failed clearing alarms\n");
			goto out;

		} else {
			printf("Alarm stopped.\n");
		}

	} else {
		result = px4_ioctl(fd, TONE_SET_ALARM, TONE_STOP_TUNE);

		if (result < 0) {
			printf("failed clearing alarms\n");
			goto out;
		}

		result = px4_ioctl(fd, TONE_SET_ALARM, tone);

		if (result < 0) {
			printf("failed setting alarm %lu\n", tone);

		} else {
			printf("Alarm %lu (disable with: tests tone 0)\n", tone);
		}
	}

out:

	if (fd >= 0) {
		px4_close(fd);
	}

	return 0;
}

开发者ID:DonLakeFlyer，项目名称:Firmware，代码行数:55，代码来源:test_hrt.cpp

示例11: switch

void Tiltrotor::set_rear_motor_state(rear_motor_state state)
{
	int pwm_value = PWM_DEFAULT_MAX;

	// map desired rear rotor state to max allowed pwm signal
	switch (state) {
	case ENABLED:
		pwm_value = PWM_DEFAULT_MAX;
		_rear_motors = ENABLED;
		break;

	case DISABLED:
		pwm_value = PWM_LOWEST_MAX;
		_rear_motors = DISABLED;
		break;

	case IDLE:
		pwm_value = _params->idle_pwm_mc;
		_rear_motors = IDLE;
		break;
	}

	int ret;
	unsigned servo_count;
	char *dev = PWM_OUTPUT0_DEVICE_PATH;
	int fd = px4_open(dev, 0);

	if (fd < 0) {PX4_WARN("can't open %s", dev);}

	ret = px4_ioctl(fd, PWM_SERVO_GET_COUNT, (unsigned long)&servo_count);
	struct pwm_output_values pwm_values;
	memset(&pwm_values, 0, sizeof(pwm_values));

	for (int i = 0; i < _params->vtol_motor_count; i++) {
		if (is_motor_off_channel(i)) {
			pwm_values.values[i] = pwm_value;

		} else {
			pwm_values.values[i] = PWM_DEFAULT_MAX;
		}

		pwm_values.channel_count = _params->vtol_motor_count;
	}

	ret = px4_ioctl(fd, PWM_SERVO_SET_MAX_PWM, (long unsigned int)&pwm_values);

	if (ret != OK) {PX4_WARN("failed setting max values");}

	px4_close(fd);
}

开发者ID:radkog，项目名称:Firmware，代码行数:50，代码来源:tiltrotor.cpp

示例12: led_off

int led_off(int led)
{
	if (leds < 0) {
		return leds;
	}
	return px4_ioctl(leds, LED_OFF, led);
}

开发者ID:Bjarne-Madsen，项目名称:Firmware，代码行数:7，代码来源:commander_helper.cpp

示例13: start

// Start the driver.
// This function call only returns once the driver is up and running
// or failed to detect the sensor.
void
start(uint8_t i2c_bus)
{
	int fd = -1;

	if (g_dev != nullptr) {
		PX4_ERR("already started");
		goto fail;
	}

	g_dev = new MS5525(i2c_bus, I2C_ADDRESS_1_MS5525DSO, PATH_MS5525);

	/* check if the MS4525DO was instantiated */
	if (g_dev == nullptr) {
		goto fail;
	}

	/* try the next MS5525DSO if init fails */
	if (OK != g_dev->Airspeed::init()) {
		delete g_dev;

		PX4_WARN("trying MS5525 address 2");

		g_dev = new MS5525(i2c_bus, I2C_ADDRESS_2_MS5525DSO, PATH_MS5525);

		/* check if the MS5525DSO was instantiated */
		if (g_dev == nullptr) {
			PX4_WARN("MS5525 was not instantiated");
			goto fail;
		}

		/* both versions failed if the init for the MS5525DSO fails, give up */
		if (OK != g_dev->Airspeed::init()) {
			PX4_WARN("MS5525 init fail");
			goto fail;
		}
	}

	/* set the poll rate to default, starts automatic data collection */
	fd = px4_open(PATH_MS5525, O_RDONLY);

	if (fd < 0) {
		goto fail;
	}

	if (px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT) < 0) {
		goto fail;
	}

	return;

fail:

	if (g_dev != nullptr) {
		delete g_dev;
		g_dev = nullptr;
	}

	PX4_WARN("no MS5525 airspeed sensor connected");
}

开发者ID:Kumru，项目名称:Firmware，代码行数:63，代码来源:MS5525_main.cpp

示例14: led_on

int led_on(int led)
{
	if (leds < 0) {
		return leds;
	}
	return px4_ioctl(leds, LED_ON, led);
}

开发者ID:Bjarne-Madsen，项目名称:Firmware，代码行数:7，代码来源:commander_helper.cpp

示例15: led_toggle

int led_toggle(int led)
{
	if (leds < 0) {
		return leds;
	}
	return px4_ioctl(leds, LED_TOGGLE, led);
}

开发者ID:Bjarne-Madsen，项目名称:Firmware，代码行数:7，代码来源:commander_helper.cpp

示例16: node_open

orb_advert_t uORB::Manager::orb_advertise_multi(const struct orb_metadata *meta, const void *data, int *instance, int priority)
{
  int result, fd;
  orb_advert_t advertiser;

  //warnx("orb_advertise_multi meta = %p\n", meta);

  /* open the node as an advertiser */
  fd = node_open(PUBSUB, meta, data, true, instance, priority);
  if (fd == ERROR) {
    warnx("node_open as advertiser failed.");
    return nullptr;
  }

  /* get the advertiser handle and close the node */
  result = px4_ioctl(fd, ORBIOCGADVERTISER, (unsigned long)&advertiser);
  px4_close(fd);
  if (result == ERROR) {
    warnx("px4_ioctl ORBIOCGADVERTISER  failed. fd = %d", fd);
    return nullptr;
  }

  /* the advertiser must perform an initial publish to initialise the object */
  result = orb_publish(meta, advertiser, data);
  if (result == ERROR) {
    warnx("orb_publish failed");
    return nullptr;
  }

  return advertiser;
}

开发者ID:afourteia，项目名称:Firmware，代码行数:31，代码来源:uORBManager_posix.cpp

示例17: px4_open

int uORB::Manager::node_advertise
(
    const struct orb_metadata *meta,
    int *instance,
    int priority
)
{
  int fd = -1;
  int ret = ERROR;

  /* fill advertiser data */
  const struct orb_advertdata adv = { meta, instance, priority };

  /* open the control device */
  fd = px4_open(TOPIC_MASTER_DEVICE_PATH, 0);

  if (fd < 0)
    goto out;

  /* advertise the object */
  ret = px4_ioctl(fd, ORBIOCADVERTISE, (unsigned long)(uintptr_t)&adv);

  /* it's PX4_OK if it already exists */
  if ((PX4_OK != ret) && (EEXIST == errno)) {
    ret = PX4_OK;
  }

out:

  if (fd >= 0)
    px4_close(fd);

  return ret;
}

开发者ID:afourteia，项目名称:Firmware，代码行数:34，代码来源:uORBManager_posix.cpp

示例18: start_bus

/**
 * Start the driver on a specific bus.
 *
 * This function call only returns once the driver is up and running
 * or failed to detect the sensor.
 */
int
start_bus(uint8_t i2c_bus)
{
	int fd = -1;

	if (g_dev != nullptr) {
		PX4_WARN("already started");
		return PX4_ERROR;
	}

	g_dev = new SDP3X(i2c_bus, I2C_ADDRESS_1_SDP3X, PATH_SDP3X);

	/* check if the SDP3XDSO was instantiated */
	if (g_dev == nullptr) {
		goto fail;
	}

	/* try the next SDP3XDSO if init fails */
	if (g_dev->init() != PX4_OK) {
		delete g_dev;

		g_dev = new SDP3X(i2c_bus, I2C_ADDRESS_2_SDP3X, PATH_SDP3X);

		/* check if the SDP3XDSO was instantiated */
		if (g_dev == nullptr) {
			PX4_ERR("SDP3X was not instantiated (RAM)");
			goto fail;
		}

		/* both versions failed if the init for the SDP3XDSO fails, give up */
		if (g_dev->init() != PX4_OK) {
			goto fail;
		}
	}

	/* set the poll rate to default, starts automatic data collection */
	fd = px4_open(PATH_SDP3X, O_RDONLY);

	if (fd < 0) {
		goto fail;
	}

	if (px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT) < 0) {
		goto fail;
	}

	return PX4_OK;

fail:

	if (g_dev != nullptr) {
		delete g_dev;
		g_dev = nullptr;
	}

	PX4_WARN("not started on bus %d", i2c_bus);

	return PX4_ERROR;
}

开发者ID:elikos，项目名称:Firmware，代码行数:65，代码来源:SDP3X_main.cpp

示例19: reset

/**
 * Reset the driver.
 */
void
reset()
{
	int fd = px4_open(ETS_PATH, O_RDONLY);

	if (fd < 0) {
		PX4_ERR("failed ");
	}

	if (px4_ioctl(fd, SENSORIOCRESET, 0) < 0) {
		PX4_ERR("driver reset failed");
	}

	if (px4_ioctl(fd, SENSORIOCSPOLLRATE, SENSOR_POLLRATE_DEFAULT) < 0) {
		PX4_ERR("driver poll restart failed");
	}
}

开发者ID:Kumru，项目名称:Firmware，代码行数:20，代码来源:ets_airspeed.cpp

示例20: rgbled_set_color

void rgbled_set_color(rgbled_color_t color)
{

	if (rgbleds < 0) {
		return;
	}
	px4_ioctl(rgbleds, RGBLED_SET_COLOR, (unsigned long)color);
}

开发者ID:Bjarne-Madsen，项目名称:Firmware，代码行数:8，代码来源:commander_helper.cpp

注：本文中的px4_ioctl函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ px4_open函数代码示例发布时间：2022-05-30

C++ px4_close函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19194|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9988|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8327|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8696|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8639|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9658|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8624|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7998|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8656|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7535|2022-11-06

客服电话

电子邮件

C++ px4_ioctl函数代码示例

示例1: px4_open

示例2: px4_open

示例3: reset

示例4: px4_open

示例5: load

示例6: test_gpio

示例7: test

示例8: test

示例9: test

示例10: test_tone

示例11: switch

示例12: led_off

示例13: start

示例14: led_on

示例15: led_toggle

示例16: node_open

示例17: px4_open

示例18: start_bus

示例19: reset

示例20: rgbled_set_color

请发表评论

全部评论

上一篇：

下一篇：

AnsiString在Delphi中虽然不可用，但是，在

krishnaik06/Machine-Learning-in-90-days

CVE-2022-31537

armancodv/building-energy-model-matlab:

美元符号为什么是“$”

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053