本文整理汇总了C++中post_cache_as_ram函数的典型用法代码示例。如果您正苦于以下问题：C++ post_cache_as_ram函数的具体用法？C++ post_cache_as_ram怎么用？C++ post_cache_as_ram使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了post_cache_as_ram函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
#endif
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
pc87360_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_default_resource_map();
needs_reset = setup_coherent_ht_domain();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* This is needed to be able to call udelay(). It could be moved to
* memreset_setup, since udelay is called in memreset. */
init_timer();
// automatically set that for you, but you might meet tight space
needs_reset |= ht_setup_chains_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
post_cache_as_ram();
}
开发者ID:hustcalm，项目名称:coreboot-hacking，代码行数:59，代码来源:romstage.c
示例2: cache_as_ram_main
//.........这里部分代码省略.........
report_bist_failure(bist);
pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
/* Setup sysinfo defaults */
set_sysinfo_in_ram(0);
update_microcode(val);
post_code(0x33);
cpuSetAMDMSR(0);
post_code(0x34);
amd_ht_init(sysinfo);
post_code(0x35);
/* Setup nodes PCI space and start core 0 AP init. */
finalize_node_setup(sysinfo);
post_code(0x36);
/* wait for all the APs core0 started by finalize_node_setup. */
/* FIXME: A bunch of cores are going to start output to serial at once.
* It would be nice to fixup prink spinlocks for ROM XIP mode.
* I think it could be done by putting the spinlock flag in the cache
* of the BSP located right after sysinfo.
*/
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/* Core0 on each node is configured. Now setup any additional cores. */
printk(BIOS_DEBUG, "start_other_cores()\n");
start_other_cores(bsp_apicid);
post_code(0x37);
wait_all_other_cores_started(bsp_apicid);
#endif
#if CONFIG_SET_FIDVID
msr = rdmsr(0xc0010071);
printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
/* FIXME: The sb fid change may survive the warm reset and only
* need to be done once.*/
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
post_code(0x39);
if (!warm_reset_detect(0)) { // BSP is node 0
init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
} else {
init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0
}
post_code(0x3A);
/* show final fid and vid */
msr = rdmsr(0xc0010071);
printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif
init_timer();
/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
if (!warm_reset_detect(0)) {
printk(BIOS_INFO, "...WARM RESET...\n\n\n");
soft_reset();
die("After soft_reset_x - shouldn't see this message!!!\n");
}
/* It's the time to set ctrl in sysinfo now; */
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
//do we need apci timer, tsc...., only debug need it for better output
/* all ap stopped? */
// init_timer(); // Need to use TMICT to synchronize FID/VID
timestamp_add_now(TS_BEFORE_INITRAM);
printk(BIOS_DEBUG, "raminit_amdmct()\n");
raminit_amdmct(sysinfo);
timestamp_add_now(TS_AFTER_INITRAM);
cbmem_initialize_empty();
post_code(0x41);
amdmct_cbmem_store_info(sysinfo);
bcm5785_early_setup();
post_cache_as_ram();
}
开发者ID:lynxis，项目名称:coreboot-signed，代码行数:101，代码来源:romstage.c
示例3: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
#endif
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_khepri_resource_map();
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
needs_reset |= ht_setup_chains_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
#if 0
dump_pci_devices();
#endif
post_cache_as_ram();
}
开发者ID:0ida，项目名称:coreboot，代码行数:65，代码来源:romstage.c
示例4: cache_as_ram_main
//.........这里部分代码省略.........
post_code(0x33);
cpuSetAMDMSR();
post_code(0x34);
amd_ht_init(sysinfo);
post_code(0x35);
/* Setup nodes PCI space and start core 0 AP init. */
finalize_node_setup(sysinfo);
/* Setup any mainboard PCI settings etc. */
setup_mb_resource_map();
post_code(0x36);
/* wait for all the APs core0 started by finalize_node_setup. */
/* FIXME: A bunch of cores are going to start output to serial at once.
It would be nice to fixup prink spinlocks for ROM XIP mode.
I think it could be done by putting the spinlock flag in the cache
of the BSP located right after sysinfo.
*/
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/* Core0 on each node is configured. Now setup any additional cores. */
printk(BIOS_DEBUG, "start_other_cores()\n");
start_other_cores();
post_code(0x37);
wait_all_other_cores_started(bsp_apicid);
#endif
post_code(0x38);
/* run _early_setup before soft-reset. */
rs780_early_setup();
sb7xx_51xx_early_setup();
#if CONFIG_SET_FIDVID
msr = rdmsr(0xc0010071);
printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
/* FIXME: The sb fid change may survive the warm reset and only
need to be done once.*/
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
post_code(0x39);
if (!warm_reset_detect(0)) { // BSP is node 0
init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
} else {
init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0
}
post_code(0x3A);
/* show final fid and vid */
msr=rdmsr(0xc0010071);
printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
#endif
rs780_htinit();
/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
if (!warm_reset_detect(0)) {
print_info("...WARM RESET...\n\n\n");
soft_reset();
die("After soft_reset_x - shouldn't see this message!!!\n");
}
post_code(0x3B);
/* It's the time to set ctrl in sysinfo now; */
printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
post_code(0x40);
// die("Die Before MCT init.");
printk(BIOS_DEBUG, "raminit_amdmct()\n");
raminit_amdmct(sysinfo);
post_code(0x41);
/*
dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 2), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200);
*/
// die("After MCT init before CAR disabled.");
rs780_before_pci_init();
sb7xx_51xx_before_pci_init();
post_code(0x42);
post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB.
post_code(0x43); // Should never see this post code.
}
开发者ID:B-Rich，项目名称:coreboot，代码行数:101，代码来源:romstage.c
示例5: cache_as_ram_main
//.........这里部分代码省略.........
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
#if 0
uint8_t tmp = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
/* The following line will set CLKIN to 24 MHz, external */
pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_CLOCKSEL, 0x11);
tmp = pnp_read_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP);
/* Is serial flash enabled? Then enable writing to serial flash. */
if (tmp & 0x0e) {
pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP, tmp | 0x10);
pnp_set_logical_device(GPIO_DEV);
/* Set Serial Flash interface to 0x0820 */
pnp_write_config(GPIO_DEV, 0x64, 0x08);
pnp_write_config(GPIO_DEV, 0x65, 0x20);
}
it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
#endif
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
#endif
init_timer(); // Need to use TMICT to synconize FID/VID
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
开发者ID:0ida，项目名称:coreboot，代码行数:101，代码来源:romstage.c
示例6: cache_as_ram_main
//.........这里部分代码省略.........
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
/* Setup sysinfo defaults */
set_sysinfo_in_ram(0);
update_microcode(val);
post_code(0x33);
cpuSetAMDMSR(0);
post_code(0x34);
amd_ht_init(sysinfo);
post_code(0x35);
/* Setup nodes PCI space and start core 0 AP init. */
finalize_node_setup(sysinfo);
/* Setup any mainboard PCI settings etc. */
setup_mb_resource_map();
post_code(0x36);
/* wait for all the APs core0 started by finalize_node_setup. */
/* FIXME: A bunch of cores are going to start output to serial at once.
It would be nice to fixup prink spinlocks for ROM XIP mode.
I think it could be done by putting the spinlock flag in the cache
of the BSP located right after sysinfo.
*/
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/* Core0 on each node is configured. Now setup any additional cores. */
printk(BIOS_DEBUG, "start_other_cores()\n");
start_other_cores(bsp_apicid);
post_code(0x37);
wait_all_other_cores_started(bsp_apicid);
#endif
post_code(0x38);
/* run _early_setup before soft-reset. */
rs780_early_setup();
#if CONFIG_SET_FIDVID
msr = rdmsr(0xc0010071);
printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
post_code(0x39);
if (!warm_reset_detect(0)) { /* BSP is node 0 */
init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
} else {
init_fidvid_stage2(bsp_apicid, 0); /* BSP is node 0 */
}
post_code(0x3A);
/* show final fid and vid */
msr = rdmsr(0xc0010071);
printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif
rs780_htinit();
/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
if (!warm_reset_detect(0)) {
printk(BIOS_INFO, "...WARM RESET...\n\n\n");
soft_reset();
die("After soft_reset_x - shouldn't see this message!!!\n");
}
post_code(0x3B);
/* It's the time to set ctrl in sysinfo now; */
printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
post_code(0x40);
timestamp_add_now(TS_BEFORE_INITRAM);
printk(BIOS_DEBUG, "raminit_amdmct()\n");
raminit_amdmct(sysinfo);
timestamp_add_now(TS_AFTER_INITRAM);
cbmem_initialize_empty();
post_code(0x41);
amdmct_cbmem_store_info(sysinfo);
rs780_before_pci_init();
post_code(0x42);
post_cache_as_ram(); /* BSP switch stack to ram, copy then execute LB. */
post_code(0x43); /* Should never see this post code. */
}
开发者ID:siro20，项目名称:coreboot，代码行数:101，代码来源:romstage.c
示例7: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const u16 spd_addr [] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
lpc47b397_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
sio_gpio_setup();
setup_mb_resource_map();
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
needs_reset |= ht_setup_chains_x();
needs_reset |= ck804_early_setup_x();
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
post_cache_as_ram();
}
开发者ID:0ida，项目名称:coreboot，代码行数:61，代码来源:romstage.c
示例8: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
setup_mb_resource_map();
dme1737_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
#endif
init_timer(); /* Need to use TMICT to synchronize FID/VID. */
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
/* mask NMI from constantly-asserted-on-this-board SERR# */
outb((inb(NMI_SC) & 0x0f) | PCI_SERR_EN, NMI_SC);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
开发者ID:AdriDlu，项目名称:coreboot，代码行数:97，代码来源:romstage.c
示例9: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// first node
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// second node
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE
+ CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset;
unsigned bsp_apicid = 0;
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
setup_default_resource_map();
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
#endif
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset_x(sysinfo->sbbusn, sysinfo->sbdn);
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
#if 0
dump_smbus_registers();
#endif
memreset_setup();
//do we need apci timer, tsc...., only debug need it for better output
/* all ap stopped? */
init_timer(); // Need to use TMICT to synconize FID/VID
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
#if 0
dump_pci_devices();
#endif
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
//.........这里部分代码省略.........
开发者ID:XVilka，项目名称:coreboot，代码行数:101，代码来源:romstage.c
示例10: cache_as_ram_main
//.........这里部分代码省略.........
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
enable_rs690_dev8(); // enable CFG access to Dev8, which is the SB P2P Bridge
sb600_lpc_init();
#if defined(DUMP_CMOS_RAM) && (DUMP_CMOS_RAM == 0)
check_cmos(); // rebooting in case of corrupted cmos !!!!!
#endif
/* it8712f_enable_serial does not use its 1st parameter. */
it8712f_enable_serial(0, CONFIG_TTYS0_BASE);
it8712f_kill_watchdog();
console_init();
#if defined(DUMP_CMOS_RAM) && (DUMP_CMOS_RAM == 1)
check_cmos(); // rebooting in case of corrupted cmos !!!!!
#endif
post_code(0x03);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
__DEBUG__("bsp_apicid=0x%x\n", bsp_apicid);
setup_sitemp_resource_map();
setup_coherent_ht_domain();
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched */
wait_all_core0_started();
start_other_cores();
#endif
wait_all_aps_started(bsp_apicid);
ht_setup_chains_x(sysinfo);
/* run _early_setup before soft-reset. */
rs690_early_setup();
sb600_early_setup();
post_code(0x04);
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
cpuid1 = cpuid(0x80000007);
if( (cpuid1.edx & 0x6) == 0x6 ) {
/* Read FIDVID_STATUS */
msr=rdmsr(0xc0010042);
__DEBUG__("begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
/* show final fid and vid */
msr=rdmsr(0xc0010042);
__DEBUG__("end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
} else {
__DEBUG__("Changing FIDVID not supported\n");
}
post_code(0x05);
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
rs690_htinit();
__DEBUG__("needs_reset=0x%x\n", needs_reset);
post_code(0x06);
if (needs_reset) {
__INFO__("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now; */
__DEBUG__("sysinfo->nodes: %2x sysinfo->ctrl: %p spd_addr: %p\n",
sysinfo->nodes, sysinfo->ctrl, spd_addr);
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
post_code(0x07);
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_code(0x08);
rs690_before_pci_init(); // does nothing
sb600_before_pci_init();
#if CONFIG_USE_OPTION_TABLE
if( read_option(cmos_defaults_loaded, 0) )
__WARNING__("WARNING: CMOS DEFAULTS LOADED. PLEASE CHECK CMOS OPTION \"cmos_default_loaded\" !\n");
#endif
post_cache_as_ram();
}
开发者ID:DarkDefender，项目名称:coreboot，代码行数:101，代码来源:romstage.c
示例11: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// Node 0
RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6,
RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7,
// node 1
RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
};
unsigned bsp_apicid = 0;
int needs_reset;
struct sys_info *sysinfo = &sysinfo_car;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0) {
//init_cpus(cpu_init_detectedx);
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_ms9282_resource_map();
setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
//wait_all_other_cores_started(bsp_apicid);
#endif
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
init_timer(); /* Need to use TMICT to synchronize FID/VID. */
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
//It's the time to set ctrl now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram();
}
开发者ID:siro20，项目名称:coreboot，代码行数:65，代码来源:romstage.c
示例12: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
DIMM0, 0, 0, 0,
DIMM1, 0, 0, 0,
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
// post_code(0x32);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
#endif
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#if CONFIG_SET_FIDVID
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
if ((cpuid_edx(0x80000007) & 0x6) == 0x6) {
msr_t msr;
/* Read FIDVID_STATUS */
msr = rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
enable_fid_change();
init_fidvid_bsp(bsp_apicid);
msr = rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
}
#endif
needs_reset |= ht_setup_chains_x();
needs_reset |= ck804_early_setup_x();
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
#if 0
dump_spd_registers(&cpu[0]);
dump_smbus_registers();
#endif
memreset_setup();
sdram_initialize(nodes, ctrl);
#if 0
print_pci_devices();
dump_pci_devices();
#endif
post_cache_as_ram();
}
开发者ID:lynxis，项目名称:coreboot-signed，代码行数:86，代码来源:romstage.c
示例13: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const u16 spd_addr[] = {
DIMM0, DIMM1, 0, 0,
0, 0, 0, 0,
0, 0, 0, 0,
0, 0, 0, 0,
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
needs_reset |= ht_setup_chains_x();
needs_reset |= ck804_early_setup_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
ms7135_set_nf4_voltage();
ms7135_set_ram_voltage();
#if CONFIG_DEBUG_SMBUS
dump_spd_registers(&ctrl[0]);
dump_smbus_registers();
#endif
sdram_initialize(nodes, ctrl);
post_cache_as_ram();
}
开发者ID:0ida，项目名称:coreboot，代码行数:65，代码来源:romstage.c
示例14: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
(0xa<<3)|0, (0xa<<3)|2, 0, 0,
(0xa<<3)|1, (0xa<<3)|3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
(0xa<<3)|4, (0xa<<3)|6, 0, 0,
(0xa<<3)|5, (0xa<<3)|7, 0, 0,
#endif
};
int needs_reset;
unsigned bsp_apicid = 0;
struct mem_controller ctrl[8];
unsigned nodes;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
/* Setup the ck804 */
ck804_enable_rom();
}
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx);
}
// post_code(0x32);
w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
uart_init();
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_s2891_resource_map();
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
needs_reset |= ht_setup_chains_x();
needs_reset |= ck804_early_setup_x();
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
#if 0
dump_spd_registers(&cpu[0]);
#endif
#if 0
dump_smbus_registers();
#endif
memreset_setup();
sdram_initialize(nodes, ctrl);
#if 0
print_pci_devices();
#endif
#if 0
dump_pci_devices();
#endif
post_cache_as_ram();
}
开发者ID:jaanek，项目名称:coreboot，代码行数:93，代码来源:romstage.c
示例15: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
RC0|DIMM0, RC0|DIMM2, 0, 0,
RC0|DIMM1, RC0|DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
RC1|DIMM0, RC1|DIMM2, 0, 0,
RC1|DIMM1, RC1|DIMM3, 0, 0,
#endif
#if CONFIG_MAX_PHYSICAL_CPUS > 2
RC2|DIMM0, RC2|DIMM2, 0, 0,
RC2|DIMM1, RC2|DIMM3, 0, 0,
RC3|DIMM0, RC3|DIMM2, 0, 0,
RC3|DIMM1, RC3|DIMM3, 0, 0,
#endif
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_s4882_resource_map();
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
// automatically set that for you, but you might meet tight space
needs_reset |= ht_setup_chains_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
post_cache_as_ram();
}
开发者ID:XVilka，项目名称:coreboot，代码行数:62，代码来源:romstage.c
示例16: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
unsigned bsp_apicid = 0;
int needs_reset = 0;
struct sys_info *sysinfo = &sysinfo_car;
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
it8712f_kill_watchdog();
it8712f_enable_3vsbsw();
console_init();
enable_rom_decode();
printk(BIOS_INFO, "now booting... \n");
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
/* Halt if there was a built in self test failure. */
report_bist_failure(bist);
setup_default_resource_map();
setup_coherent_ht_domain();
wait_all_core0_started();
printk(BIOS_INFO, "now booting... All core 0 started\n");
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched. */
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
init_timer();
ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
needs_reset = optimize_link_coherent_ht();
print_debug_hex8(needs_reset);
needs_reset |= optimize_link_incoherent_ht(sysinfo);
print_debug_hex8(needs_reset);
needs_reset |= k8t890_early_setup_ht();
print_debug_hex8(needs_reset);
vt8237_early_network_init(NULL);
vt8237_early_spi_init();
if (needs_reset) {
printk(BIOS_DEBUG, "ht reset -\n");
soft_reset();
printk(BIOS_DEBUG, "FAILED!\n");
}
/* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */
/* allow LDT STOP asserts */
vt8237_sb_enable_fid_vid();
enable_fid_change();
print_debug("after enable_fid_change\n");
init_fidvid_bsp(bsp_apicid);
/* Stop the APs so we can start them later in init. */
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now. */
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram();
}
开发者ID:nasirg80，项目名称:coreboot，代码行数:75，代码来源:romstage.c
示例17: cache_as_ram_main
//.........这里部分代码省略.........
int needs_reset = 0;
u32 bsp_apicid = 0;
msr_t msr;
struct cpuid_result cpuid1;
struct sys_info *sysinfo = &sysinfo_car;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
/* sb600_lpc_port80(); */
sb600_pci_port80();
}
technexion_post_code_init();
technexion_post_code(LED_MESSAGE_START);
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
enable_rs690_dev8();
sb600_lpc_init();
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
ite_kill_watchdog(GPIO_DEV);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "bsp_apicid=0x%x\n", bsp_apicid);
setup_tim5690_resource_map();
setup_coherent_ht_domain();
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched */
wait_all_core0_started();
start_other_cores();
#endif
wait_all_aps_started(bsp_apicid);
ht_setup_chains_x(sysinfo);
/* run _early_setup before soft-reset. */
rs690_early_setup();
sb600_early_setup();
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
cpuid1 = cpuid(0x80000007);
if ((cpuid1.edx & 0x6) == 0x6) {
/* Read FIDVID_STATUS */
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
/* show final fid and vid */
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
} else {
printk(BIOS_DEBUG, "Changing FIDVID not supported\n");
}
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
rs690_htinit();
printk(BIOS_DEBUG, "needs_reset=0x%x\n", needs_reset);
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
speaker_init(255);
speaker_on_nodelay();
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now; */
printk(BIOS_DEBUG, "sysinfo->nodes: %2x sysinfo->ctrl: %p spd_addr: %p\n",
sysinfo->nodes, sysinfo->ctrl, spd_addr);
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
technexion_post_code(LED_MESSAGE_RAM);
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
speaker_off_nodelay();
rs690_before_pci_init();
sb600_before_pci_init();
post_cache_as_ram();
}
开发者ID:RafaelRMachado，项目名称:Coreboot，代码行数:101，代码来源:romstage.c
示例18: cache_as_ram_main
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
#endif
};
int needs_reset;
unsigned nodes, bsp_apicid = 0;
struct mem_controller ctrl[8];
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(
|
客服电话
APP下载
官方微信
请发表评论