C++ platform_mcu_powersave_disable函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中platform_mcu_powersave_disable函数的典型用法代码示例。如果您正苦于以下问题：C++ platform_mcu_powersave_disable函数的具体用法？C++ platform_mcu_powersave_disable怎么用？C++ platform_mcu_powersave_disable使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了platform_mcu_powersave_disable函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: MicoMcuPowerSaveConfig

void MicoMcuPowerSaveConfig( int enable )
{
  if (enable == 1)
    platform_mcu_powersave_enable( );
  else
    platform_mcu_powersave_disable( );
}

开发者ID:robbie-cao，项目名称:MiCO，代码行数:7，代码来源:mico_platform_common.c

示例2: platform_init_mcu_infrastructure

void platform_init_mcu_infrastructure( void )
{
    uint8_t i;

#ifdef INTERRUPT_VECTORS_IN_RAM
    SCB->VTOR = 0x20000000; /* Change the vector table to point to start of SRAM */
#endif /* ifdef INTERRUPT_VECTORS_IN_RAM */

    /* Initialise watchdog */
    platform_watchdog_init( );

    /* Initialise interrupt priorities */
    for ( i = 0; i < 81; i++ )
    {
        NVIC_SetPriority( (IRQn_Type) i, 0xf );
    }
    NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 );
    platform_init_rtos_irq_priorities();
    platform_init_peripheral_irq_priorities();

    /* Initialise GPIO IRQ manager */
    platform_gpio_irq_manager_init();

#ifndef WICED_DISABLE_MCU_POWERSAVE
    /* Initialise MCU powersave */
    platform_mcu_powersave_init( );
    platform_mcu_powersave_disable( );

    /* Initialise RTC */
    platform_rtc_init( );
#endif /* ifndef WICED_DISABLE_MCU_POWERSAVE */
}

开发者ID:fishbaoz，项目名称:wiced-emw3165，代码行数:32，代码来源:platform_init.c

示例3: host_platform_bus_deinit

wwd_result_t host_platform_bus_deinit( void )
{
    if ( sdio_bus_initted == WICED_TRUE )
    {
        uint8_t a = 0;

        platform_mcu_powersave_disable();

//        host_rtos_deinit_semaphore( &sdio_transfer_done_semaphore );
//        disable_sdio_block_transfer_done_irq();

        MCI_Disable( HSMCI );
        NVIC_DisableIRQ( HSMCI_IRQn );

#ifdef WICED_WIFI_USE_GPIO_FOR_BOOTSTRAP
        platform_gpio_deinit( &wifi_control_pins[WWD_PIN_BOOTSTRAP_0] );
        platform_gpio_deinit( &wifi_control_pins[WWD_PIN_BOOTSTRAP_1] );
#endif /* WICED_WIFI_USE_GPIO_FOR_BOOTSTRAP */

        /* Reset all SDIO pins to input pull-up to save power */
        for ( a = WWD_PIN_SDIO_CLK; a < WWD_PIN_SDIO_MAX; a++ )
        {
            platform_gpio_deinit( &wifi_sdio_pins[a] );
        }

        platform_mcu_powersave_enable();

        sdio_bus_initted = WICED_FALSE;
    }

    return WICED_SUCCESS;
}

开发者ID:119，项目名称:bcm-wiced-sdk，代码行数:32，代码来源:wwd_SDIO.c

示例4: platform_init_mcu_infrastructure

void platform_init_mcu_infrastructure( void )
{
    uint8_t i;

#ifdef INTERRUPT_VECTORS_IN_RAM
    SCB->VTOR = 0x20000000; /* Change the vector table to point to start of SRAM */
#endif /* ifdef INTERRUPT_VECTORS_IN_RAM */

    /* Initialise watchdog */
    platform_watchdog_init( );

    /* Initialise interrupt priorities */
    for ( i = 0; i < 35; i++ )
    {
        NVIC_SetPriority( i, 0xf );
    }
    //NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 );

    /* set priority grouping inside cpu core */
    SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup_4;

    platform_init_rtos_irq_priorities();
    platform_init_peripheral_irq_priorities();

#ifndef WICED_DISABLE_MCU_POWERSAVE
    /* Initialise MCU powersave */
    platform_mcu_powersave_init( );
    platform_mcu_powersave_disable( );

    /* Initialise RTC */
//    platform_rtc_init( );
#endif /* ifndef WICED_DISABLE_MCU_POWERSAVE */
}

开发者ID:119，项目名称:bcm-wiced-sdk，代码行数:33，代码来源:platform_init.c

示例5: platform_adc_init

OSStatus platform_adc_init( const platform_adc_t* adc, uint32_t sample_cycle )
{
  OSStatus    err = kNoErr;
  struct adc_config adc_cfg;
  UNUSED_PARAMETER(sample_cycle);

  platform_mcu_powersave_disable();
  
  require_action_quiet( adc != NULL, exit, err = kParamErr);
  
  if( initialized != true )
  {
    adc_enable();
    
    adc_select_clock_source_mck(ADC);
    
    adc_get_config_defaults(&adc_cfg);
    
    adc_init(ADC, &adc_cfg);
    
    adc_set_trigger(ADC, ADC_TRIG_SW);
    
     adc_set_resolution(ADC, adc->resolution);
    
    initialized = true;
  }
  
exit:
  platform_mcu_powersave_enable();
  return err;
}

开发者ID:SmartArduino，项目名称:MICO-1，代码行数:31，代码来源:platform_adc.c

示例6: platform_gpio_irq_enable

OSStatus platform_gpio_irq_enable( const platform_gpio_t* gpio, platform_gpio_irq_trigger_t trigger, platform_gpio_irq_callback_t handler, void* arg )
{
  uint8_t intPort;
  int i;
  OSStatus err = kNoErr;

  platform_mcu_powersave_disable();
  require_action_quiet( gpio != NULL && trigger != IRQ_TRIGGER_BOTH_EDGES, exit, err = kParamErr);
  
  switch( gpio->port ){
    case GPIOA:
      intPort = GPIO_A_INT;
      break;
    case GPIOB:
      intPort = GPIO_B_INT;
      break;
    case GPIOC:
      intPort = GPIO_C_INT;
      break;
    default:
      err = kParamErr;
      goto exit;
  }
    
  for( i = 0; i < NUMBER_OF_GPIO_IRQ_LINES; i++ ){
    if ( gpio_irq_data[i].port ==  gpio->port && gpio_irq_data[i].pin ==  gpio->pin){
      /* GPIO IRQ already exist */
      gpio_irq_data[ i ].handler    = handler;
      gpio_irq_data[ i ].arg        = arg;
      break;
    }
  }

  if(i == NUMBER_OF_GPIO_IRQ_LINES){
    /* GPIO IRQ not exist */
    for( i = 0; i < NUMBER_OF_GPIO_IRQ_LINES; i++ ){
      if ( gpio_irq_data[i].handler == NULL ){
        gpio_irq_data[ i ].port       = gpio->port;
        gpio_irq_data[ i ].pin        = gpio->pin;
        gpio_irq_data[ i ].handler    = handler;
        gpio_irq_data[ i ].arg        = arg;
        break;
      }
    } 
    /* No space to add one */
    if( i == NUMBER_OF_GPIO_IRQ_LINES)
      return kNoSpaceErr;
  }

  GpioIntClr(intPort, ((uint32_t)1 << gpio->pin));

  if( trigger == IRQ_TRIGGER_RISING_EDGE )
    GpioIntEn(intPort, ((uint32_t)1 << gpio->pin), GPIO_POS_EDGE_TRIGGER);
  else 
    GpioIntEn(intPort, ((uint32_t)1 << gpio->pin), GPIO_NEG_EDGE_TRIGGER);

exit:
  platform_mcu_powersave_enable();
  return err;
}

开发者ID:playboy51job，项目名称:MiCO_v2.2.0，代码行数:60，代码来源:platform_gpio.c

示例7: platform_adc_take_sample

OSStatus platform_adc_take_sample( const platform_adc_t* adc, uint16_t* output )
{
  OSStatus    err = kNoErr;
 
  platform_mcu_powersave_disable();
  
  require_action_quiet( adc != NULL, exit, err = kParamErr);
  
  channel_num = adc->channel;
  
  adc_channel_enable(ADC, adc->channel);
    
  adc_set_callback(ADC, adc->interrupt, adc_end_conversion, 1);
  
  /* Start conversion */
  adc_start_software_conversion(ADC);
  adc_start_calibration(ADC);
  
  while (adc_get_interrupt_status(ADC) & (1 << adc->channel));
  
  *output = adc_channel_get_value(ADC, adc->channel);	
  mico_thread_msleep(1);
  adc_channel_disable(ADC, adc->channel);
  
exit:
  platform_mcu_powersave_enable();
  return err;  
}

开发者ID:SmartArduino，项目名称:MICO-1，代码行数:28，代码来源:platform_adc.c

示例8: internalFlashErase

OSStatus internalFlashErase(uint32_t start_address, uint32_t end_address)
{
  platform_log_trace();
  uint32_t i;
  OSStatus err = kNoErr;
  uint32_t page_start_address, page_end_address;
  uint32_t page_start_number, page_end_number;

  platform_mcu_powersave_disable();

  require_action( flash_unlock( start_address, end_address, &page_start_address, &page_end_address ) == FLASH_RC_OK, exit, err = kGeneralErr );

  page_start_number = page_start_address/512;
  page_end_number   = page_end_address/512;
  require_action( page_end_number >= page_start_number + 16, exit, err = kUnsupportedErr);

  for ( i = page_start_number; i <= page_end_number; i+=16 )
  {
    require_action( flash_erase_page( i * 512, IFLASH_ERASE_PAGES_16) == FLASH_RC_OK, exit, err = kGeneralErr );
  }

  require_action( flash_lock( start_address, end_address, NULL, NULL ) == FLASH_RC_OK, exit, err = kGeneralErr );

exit:
  platform_mcu_powersave_enable();
  return err;
}

开发者ID:yinhongxing，项目名称:mico，代码行数:27，代码来源:platform_flash.c

示例9: platform_gpio_irq_disable

OSStatus platform_gpio_irq_disable( const platform_gpio_t* gpio )
{
  uint16_t interrupt_line;
  OSStatus err = kNoErr;

  platform_mcu_powersave_disable();
  require_action_quiet( gpio != NULL, exit, err = kParamErr);

  interrupt_line = (uint16_t) ( 1 << gpio->pin_number );

  if ( ( EXTI->IMR & interrupt_line ) && gpio_irq_data[gpio->pin_number].owner_port == gpio->port )
  {
    bool             interrupt_line_used = 0;
    IRQn_Type        interrupt_vector    = (IRQn_Type)0;
    EXTI_InitTypeDef exti_init_structure;

    /* Disable EXTI interrupt line */
    exti_init_structure.EXTI_Line    = (uint32_t)interrupt_line;
    exti_init_structure.EXTI_LineCmd = DISABLE;
    exti_init_structure.EXTI_Mode    = EXTI_Mode_Interrupt;
    exti_init_structure.EXTI_Trigger = EXTI_Trigger_Rising;
    EXTI_Init( &exti_init_structure );
    exti_init_structure.EXTI_Trigger = EXTI_Trigger_Falling;
    EXTI_Init( &exti_init_structure );

    /* Disable NVIC interrupt */
    if ( ( interrupt_line & 0x001F ) != 0 )
    {
      /* Line 0 to 4 */
      interrupt_vector = (IRQn_Type) ( EXTI0_IRQn + gpio->pin_number );
      interrupt_line_used = false;
    }
    else if ( ( interrupt_line & 0x03E0 ) != 0 )
    {
      /* Line 5 to 9 */
      interrupt_vector = EXTI9_5_IRQn;
      interrupt_line_used = ( ( EXTI->IMR & 0x3e0U ) != 0 ) ? true : false;
    }
    else if ( ( interrupt_line & 0xFC00 ) != 0 )
    {
      /* Line 10 to 15 */
      interrupt_vector = EXTI15_10_IRQn;
      interrupt_line_used = ( ( EXTI->IMR & 0xfc00U ) != 0 ) ? true : false;
    }

    /* Some IRQ lines share a vector. Disable vector only if not used */
    if ( interrupt_line_used == false )
    {
      NVIC_DisableIRQ( interrupt_vector );
    }

    gpio_irq_data[gpio->pin_number].owner_port = 0;
    gpio_irq_data[gpio->pin_number].handler    = 0;
    gpio_irq_data[gpio->pin_number].arg        = 0;
  }

exit:
  platform_mcu_powersave_enable();
  return err;
}

开发者ID:70year，项目名称:MICO，代码行数:60，代码来源:platform_gpio.c

示例10: host_platform_bus_deinit

OSStatus host_platform_bus_deinit( void )
{
  platform_mcu_powersave_disable( );
  
  NVIC_DisableIRQ( platform_flexcom_irq_numbers[wifi_spi.spi_id] );
  pdc_disable_transfer( spi_get_pdc_base( wifi_spi.port ), PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS );
  spi_disable(wifi_spi.port);
  
  /* Deinit the SPI lines */
  platform_gpio_peripheral_pin_init(  wifi_spi.mosi_pin,  INPUT_HIGH_IMPEDANCE );
  platform_gpio_peripheral_pin_init(  wifi_spi.miso_pin,  INPUT_HIGH_IMPEDANCE );
  platform_gpio_peripheral_pin_init(  wifi_spi.clock_pin, INPUT_HIGH_IMPEDANCE );
  
  /* Deinit the interrupt input for WLAN_IRQ */
  platform_gpio_init( &wifi_spi_pins[WIFI_PIN_SPI_IRQ], INPUT_HIGH_IMPEDANCE );
  platform_gpio_irq_disable( &wifi_spi_pins[WIFI_PIN_SPI_IRQ] );
  
  /* Deinit SPI slave select GPIOs */
  platform_gpio_init( &wifi_spi_pins[WIFI_PIN_SPI_CS], INPUT_HIGH_IMPEDANCE );
  
#if defined ( MICO_WIFI_USE_GPIO_FOR_BOOTSTRAP )
  platform_gpio_init( &wifi_control_pins[WIFI_PIN_BOOTSTRAP_0], INPUT_HIGH_IMPEDANCE );
  platform_gpio_init( &wifi_control_pins[WIFI_PIN_BOOTSTRAP_1], INPUT_HIGH_IMPEDANCE );
#endif
  
  platform_mcu_powersave_enable( );
  
  return kNoErr;
}

开发者ID:robbie-cao，项目名称:MiCO，代码行数:29，代码来源:wlan_bus_spi.c

示例11: host_platform_spi_transfer

OSStatus host_platform_spi_transfer( bus_transfer_direction_t dir, uint8_t* buffer, uint16_t buffer_length )
{
  OSStatus result;
  
  pdc_packet_t pdc_spi_packet = { (uint32_t)buffer, buffer_length };
  Pdc* spi_pdc  = spi_get_pdc_base( wifi_spi.port );
  
  platform_mcu_powersave_disable();
  
  platform_gpio_output_low( &wifi_spi_pins[WIFI_PIN_SPI_CS] );
  
  pdc_tx_init( spi_pdc, &pdc_spi_packet, NULL);
  
  if ( dir == BUS_READ ) {
    pdc_rx_init( spi_pdc, &pdc_spi_packet, NULL);
    
    spi_enable_interrupt(wifi_spi.port, SPI_IER_RXBUFF );
    pdc_enable_transfer( spi_pdc, PERIPH_PTCR_TXTEN | PERIPH_PTCR_RXTEN );
  } 
  
  if ( dir == BUS_WRITE ) {
    spi_enable_interrupt( wifi_spi.port, SPI_IER_ENDTX );
    pdc_enable_transfer( spi_pdc, PERIPH_PTCR_TXTEN );
  }
  
  result = mico_rtos_get_semaphore( &spi_transfer_finished_semaphore, 100 );
  
  platform_gpio_output_high( &wifi_spi_pins[WIFI_PIN_SPI_CS] );
  
  platform_mcu_powersave_enable();
  
  return result;
  
}

开发者ID:robbie-cao，项目名称:MiCO，代码行数:34，代码来源:wlan_bus_spi.c

示例12: RX_PIN_WAKEUP_handler

void RX_PIN_WAKEUP_handler(void *arg)
{
    (void)arg;
    platform_uart_driver_t* driver = arg;
    uint32_t uart_number;

    platform_gpio_enable_clock( driver->peripheral->pin_rx );

    uart_number = platform_uart_get_port_number( driver->peripheral->port );

    uart_peripheral_clock_functions[ uart_number ]( uart_peripheral_clocks[ uart_number ], ENABLE );

    /* Enable DMA peripheral clock */
    if ( driver->peripheral->tx_dma_config.controller == DMA1 )
    {
        RCC->AHB1ENR |= RCC_AHB1Periph_DMA1;
    }
    else
    {
        RCC->AHB1ENR |= RCC_AHB1Periph_DMA2;
    }

    platform_gpio_irq_disable( driver->peripheral->pin_rx );
    platform_mcu_powersave_disable( );
    mico_rtos_set_semaphore( &driver->sem_wakeup );

}

开发者ID:ilittlerui，项目名称:MICO，代码行数:27，代码来源:platform_uart.c

示例13: platform_gpio_irq_disable

OSStatus platform_gpio_irq_disable( const platform_gpio_t* gpio )
{
  OSStatus            err           = kNoErr;
  ioport_port_mask_t  mask          = ioport_pin_to_mask   ( gpio->pin );
  ioport_port_t       port          = ioport_pin_to_port_id( gpio->pin );
  volatile Pio*       port_register = arch_ioport_port_to_base( port );
  
  platform_mcu_powersave_disable();
  require_action_quiet( gpio != NULL, exit, err = kParamErr);

  /* Disable interrupt on pin */
  port_register->PIO_IDR = mask;

  /* Disable Cortex-M interrupt vector as well if no pin interrupt is enabled */
  if ( port_register->PIO_IMR == 0 )
  {
    NVIC_DisableIRQ( irq_vectors[port] );
  }

  gpio_irq_data[port][mask].wakeup_pin = false;
  gpio_irq_data[port][mask].arg        = 0;
  gpio_irq_data[port][mask].callback   = NULL;
  
exit:
  platform_mcu_powersave_enable();
  return err;
}

开发者ID:HargicStudio，项目名称:SmartCup_MiCOKit_v2.4.0.0，代码行数:27，代码来源:platform_gpio.c

示例14: platform_uart_deinit

OSStatus platform_uart_deinit( platform_uart_driver_t* driver )
{
  uint8_t          uart_number;
  OSStatus          err = kNoErr;

  platform_mcu_powersave_disable();

  require_action_quiet( ( driver != NULL ), exit, err = kParamErr);

  uart_number = platform_uart_get_port_number( driver->peripheral->port );

  /* Disable USART */
  USART_Cmd( driver->peripheral->port, DISABLE );

  /* Deinitialise USART */
  USART_DeInit( driver->peripheral->port );

  /**************************************************************************
   * De-initialise STM32 DMA and interrupt
   **************************************************************************/

  /* Deinitialise DMA streams */
  DMA_DeInit( driver->peripheral->tx_dma_config.stream );
  DMA_DeInit( driver->peripheral->rx_dma_config.stream );

  /* Disable TC (transfer complete) interrupt at the source */
  DMA_ITConfig( driver->peripheral->tx_dma_config.stream, DMA_INTERRUPT_FLAGS, DISABLE );
  DMA_ITConfig( driver->peripheral->rx_dma_config.stream, DMA_INTERRUPT_FLAGS, DISABLE );

  /* Disable transmit DMA interrupt at Cortex-M3 */
  NVIC_DisableIRQ( driver->peripheral->tx_dma_config.irq_vector );

  /**************************************************************************
   * De-initialise STM32 USART interrupt
   **************************************************************************/

  USART_ITConfig( driver->peripheral->port, USART_IT_RXNE, DISABLE );

  /* Disable UART interrupt vector on Cortex-M3 */
  NVIC_DisableIRQ( driver->peripheral->rx_dma_config.irq_vector );

  /* Disable registers clocks */
  uart_peripheral_clock_functions[uart_number]( uart_peripheral_clocks[uart_number], DISABLE );

  mico_rtos_deinit_semaphore( &driver->rx_complete );
  mico_rtos_deinit_semaphore( &driver->tx_complete );
  mico_rtos_deinit_mutex( &driver->tx_mutex );
  driver->rx_size              = 0;
  driver->tx_size              = 0;
  driver->last_transmit_result = kNoErr;
  driver->last_receive_result  = kNoErr;
  driver->initialized          = false;

exit:
    platform_mcu_powersave_enable();
    return err;
}

开发者ID:yangk，项目名称:Mico，代码行数:57，代码来源:platform_uart.c

示例15: platform_adc_init

OSStatus platform_adc_init( const platform_adc_t* adc, uint32_t sample_cycle )
{
    GPIO_InitTypeDef      gpio_init_structure;
    ADC_InitTypeDef       adc_init_structure;
    ADC_CommonInitTypeDef adc_common_init_structure;
    uint8_t     a;
    OSStatus    err = kNoErr;

    platform_mcu_powersave_disable();

    require_action_quiet( adc != NULL, exit, err = kParamErr);
    
    /* Enable peripheral clock for this port */
    err = platform_gpio_enable_clock( adc->pin );
    require_noerr(err, exit);

    /* Initialize the associated GPIO */
    gpio_init_structure.GPIO_Pin   = (uint32_t)( 1 << adc->pin->pin_number );;
    gpio_init_structure.GPIO_Speed = (GPIOSpeed_TypeDef) 0;
    gpio_init_structure.GPIO_Mode  = GPIO_Mode_AN;
    gpio_init_structure.GPIO_PuPd  = GPIO_PuPd_NOPULL;
    gpio_init_structure.GPIO_OType = GPIO_OType_OD;
    GPIO_Init( adc->pin->port, &gpio_init_structure );

    RCC_APB2PeriphClockCmd( adc->adc_peripheral_clock, ENABLE );

    /* Initialize the ADC */
    ADC_StructInit( &adc_init_structure );
    adc_init_structure.ADC_Resolution         = ADC_Resolution_12b;
    adc_init_structure.ADC_ScanConvMode       = DISABLE;
    adc_init_structure.ADC_ContinuousConvMode = DISABLE;
    adc_init_structure.ADC_ExternalTrigConv   = ADC_ExternalTrigConvEdge_None;
    adc_init_structure.ADC_DataAlign          = ADC_DataAlign_Right;
    adc_init_structure.ADC_NbrOfConversion    = 1;
    ADC_Init( adc->port, &adc_init_structure );

    ADC_CommonStructInit( &adc_common_init_structure );
    adc_common_init_structure.ADC_Mode             = ADC_Mode_Independent;
    adc_common_init_structure.ADC_DMAAccessMode    = ADC_DMAAccessMode_Disabled;
    adc_common_init_structure.ADC_Prescaler        = ADC_Prescaler_Div2;
    adc_common_init_structure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit( &adc_common_init_structure );

    ADC_Cmd( adc->port, ENABLE );

    /* Find the closest supported sampling time by the MCU */
    for ( a = 0; ( a < sizeof( adc_sampling_cycle ) / sizeof(uint16_t) ) && adc_sampling_cycle[a] < sample_cycle; a++ )
    {
    }

    /* Initialize the ADC channel */
    ADC_RegularChannelConfig( adc->port, adc->channel, adc->rank, a );

exit:
    platform_mcu_powersave_enable();
    return err;
}

开发者ID:SmartArduino，项目名称:MICO-1，代码行数:57，代码来源:platform_adc.c

示例16: host_platform_bus_init

wwd_result_t host_platform_bus_init( void )
{
    if ( sdio_bus_initted == WICED_FALSE )
    {
        uint8_t a = 0;

        platform_mcu_powersave_disable();

        /* SDIO bootstrapping: GPIO0 = 0 and GPIO1 = 0 */

#ifdef WICED_WIFI_USE_GPIO_FOR_BOOTSTRAP
        platform_gpio_init( &wifi_control_pins[WWD_PIN_BOOTSTRAP_0], OUTPUT_PUSH_PULL );
        platform_gpio_output_low( &wifi_control_pins[WWD_PIN_BOOTSTRAP_0] );

        platform_gpio_init( &wifi_control_pins[WWD_PIN_BOOTSTRAP_1], OUTPUT_PUSH_PULL );
        platform_gpio_output_low( &wifi_control_pins[WWD_PIN_BOOTSTRAP_1] );
#endif /* WICED_WIFI_USE_GPIO_FOR_BOOTSTRAP */
        /* Setup SDIO pins */
        for ( a = WWD_PIN_SDIO_CLK; a < WWD_PIN_SDIO_MAX; a++ )
        {
            if( a == WWD_PIN_SDIO_OOB_IRQ )
            {
                platform_gpio_peripheral_pin_init( &wifi_sdio_pins[a], 0 );
            }
            else
            {
                platform_gpio_peripheral_pin_init( &wifi_sdio_pins[a], ( IOPORT_MODE_MUX_C | IOPORT_MODE_PULLUP ));
            }
        }

        /* Enable the MCI peripheral */
        sysclk_enable_peripheral_clock( ID_HSMCI );

        HSMCI->HSMCI_CR = HSMCI_CR_SWRST;

        MCI_Disable( HSMCI );

        MCI_Init( &sdio_driver, HSMCI, ID_HSMCI, CPU_CLOCK_HZ );

        /* Enable SDIO interrupt */
        /* Priority must be set in platform.c file function platform_init_peripheral_irq_priorities */
        /* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! */
        /* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! */
//        NVIC_SetPriority( HSMCI_IRQn, SAM4S_SDIO_IRQ_PRIO );
        NVIC_EnableIRQ( HSMCI_IRQn );

//        host_rtos_init_semaphore( &sdio_transfer_done_semaphore );

//        enable_sdio_block_transfer_done_irq();

        platform_mcu_powersave_enable();

        sdio_bus_initted = WICED_TRUE;
    }
    return WICED_SUCCESS;
}

开发者ID:119，项目名称:bcm-wiced-sdk，代码行数:56，代码来源:wwd_SDIO.c

示例17: platform_uart_receive_bytes

OSStatus platform_uart_receive_bytes( platform_uart_driver_t* driver, uint8_t* data_in, uint32_t expected_data_size, uint32_t timeout_ms )
{
  OSStatus err = kNoErr;

  platform_mcu_powersave_disable();

  require_action_quiet( ( driver != NULL ) && ( data_in != NULL ) && ( expected_data_size != 0 ), exit, err = kParamErr);
  require_action_quiet( driver->rx_ring_buffer != NULL , exit, err = kUnsupportedErr);

  while ( expected_data_size != 0 )
  {
    uint32_t transfer_size = MIN(driver->rx_ring_buffer->size / 2, expected_data_size);

    /* Check if ring buffer already contains the required amount of data. */
    if ( transfer_size > ring_buffer_used_space( driver->rx_ring_buffer ) )
    {
      /* Set rx_size and wait in rx_complete semaphore until data reaches rx_size or timeout occurs */
      driver->rx_size = transfer_size;

      if ( mico_rtos_get_semaphore( &driver->rx_complete, timeout_ms ) != kNoErr )
      {
        driver->rx_size = 0;
        err = kTimeoutErr;
        goto exit;
      }

      /* Reset rx_size to prevent semaphore being set while nothing waits for the data */
      driver->rx_size = 0;
    }

    expected_data_size -= transfer_size;

    // Grab data from the buffer
    do
    {
      uint8_t* available_data;
      uint32_t bytes_available;

      ring_buffer_get_data( driver->rx_ring_buffer, &available_data, &bytes_available );
      bytes_available = MIN( bytes_available, transfer_size );
      memcpy( data_in, available_data, bytes_available );
      transfer_size -= bytes_available;
      data_in = ( (uint8_t*)data_in + bytes_available );
      ring_buffer_consume( driver->rx_ring_buffer, bytes_available );
    }
    while ( transfer_size != 0 );
  }

  require_action( expected_data_size == 0, exit, err = kReadErr);

exit:
  platform_mcu_powersave_enable();
  return err;

}

开发者ID:gjw09043108，项目名称:MICO，代码行数:55，代码来源:platform_uart.c

示例18: platform_gpio_output_low

platform_result_t platform_gpio_output_low( const platform_gpio_t* gpio )
{
    wiced_assert( "bad argument", ( gpio != NULL ) );

    platform_mcu_powersave_disable();

    gpio->port->BSRRH = (uint16_t) ( 1 << gpio->pin_number );

    platform_mcu_powersave_enable();

    return PLATFORM_SUCCESS;
}

开发者ID:fishbaoz，项目名称:wiced-emw3165，代码行数:12，代码来源:platform_gpio.c

示例19: internalFlashInitialize

static OSStatus internalFlashInitialize( void )
{ 
  platform_log_trace();
  OSStatus err = kNoErr;
  platform_mcu_powersave_disable();

  require_action( flash_init(FLASH_ACCESS_MODE_128, 6) == FLASH_RC_OK, exit, err = kGeneralErr );
  
exit:
  platform_mcu_powersave_enable();
  return err; 
}

开发者ID:yinhongxing，项目名称:mico，代码行数:12，代码来源:platform_flash.c

示例20: platform_gpio_deinit

OSStatus platform_gpio_deinit( const platform_gpio_t* gpio )
{
  OSStatus          err = kNoErr;

  platform_mcu_powersave_disable();
  require_action_quiet( gpio != NULL, exit, err = kParamErr);
  
  ioport_disable_pin( gpio->pin );
    
exit:
  platform_mcu_powersave_enable();
  return err;
}

开发者ID:HargicStudio，项目名称:SmartCup_MiCOKit_v2.4.0.0，代码行数:13，代码来源:platform_gpio.c

注：本文中的platform_mcu_powersave_disable函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ platform_mcu_powersave_enable函数代码示例发布时间：2022-05-30

C++ platform_get_resource_byname函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19216|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9995|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8331|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8699|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8643|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9665|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8628|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8003|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8661|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7537|2022-11-06

客服电话

电子邮件

C++ platform_mcu_powersave_disable函数代码示例

示例1: MicoMcuPowerSaveConfig

示例2: platform_init_mcu_infrastructure

示例3: host_platform_bus_deinit

示例4: platform_init_mcu_infrastructure

示例5: platform_adc_init

示例6: platform_gpio_irq_enable

示例7: platform_adc_take_sample

示例8: internalFlashErase

示例9: platform_gpio_irq_disable

示例10: host_platform_bus_deinit

示例11: host_platform_spi_transfer

示例12: RX_PIN_WAKEUP_handler

示例13: platform_gpio_irq_disable

示例14: platform_uart_deinit

示例15: platform_adc_init

示例16: host_platform_bus_init

示例17: platform_uart_receive_bytes

示例18: platform_gpio_output_low

示例19: internalFlashInitialize

示例20: platform_gpio_deinit

请发表评论

全部评论

上一篇：

下一篇：

janboddez/share-on-mastodon: Easily shar

国产质量最好的头盔测评（这4款绝对是性价

道的笔顺,认识道的笔画,讨论道的部首

marktext/marktext:

2021北京高新技巧企业人才落户政策请求资料

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053