C++ i2c_register_board_info函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中i2c_register_board_info函数的典型用法代码示例。如果您正苦于以下问题：C++ i2c_register_board_info函数的具体用法？C++ i2c_register_board_info怎么用？C++ i2c_register_board_info使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了i2c_register_board_info函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: msm7627a_add_io_devices

void __init msm7627a_add_io_devices(void)
{
	/* touchscreen */
	#ifdef CONFIG_TOUCHSCREEN_ATMEL_MAXTOUCH
	if (machine_is_msm7625a_surf() || machine_is_msm7625a_ffa()) {
		atmel_ts_pdata.min_x = 0;
		atmel_ts_pdata.max_x = 480;
		atmel_ts_pdata.min_y = 0;
		atmel_ts_pdata.max_y = 320;
	}

	i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
				atmel_ts_i2c_info,
				ARRAY_SIZE(atmel_ts_i2c_info));
	#endif

	//>>MelChang,[Harry] Add ELAN eKTF2040 and ILITEK ILI2013t touch panel IC
	#if defined(CONFIG_TOUCHSCREEN_ELAN_EKTF2040) || defined(CONFIG_TOUCHSCREEN_ILITEK_2103T) || defined(CONFIG_TOUCHSCREEN_CYPRESS_CY8CTMA340)
	gpio_tlmm_config(GPIO_CFG(CAP_TOUCH_DETECT, 0, GPIO_CFG_INPUT, GPIO_CFG_NO_PULL, GPIO_CFG_2MA), GPIO_CFG_ENABLE);
	mdelay(10);
	if(gpio_get_value(CAP_TOUCH_DETECT))
	{
		#if defined(CONFIG_TOUCHSCREEN_CYPRESS_CY8CTMA340)
		pr_info("-- CAP_TOUCH_DETECT is Cypress IC + Jtouch Panel  --\n");
		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
		i2c_touch_devices_cypress_tma340, ARRAY_SIZE(i2c_touch_devices_cypress_tma340));
		#else
		pr_info("-- CAP_TOUCH_DETECT High - Fail --\n");
		#endif
	}
	else
	{
		#if defined(CONFIG_TOUCHSCREEN_ELAN_EKTF2040)
		pr_info("-- CAP_TOUCH_DETECT is ELAN IC  --\n");
		elan_ktf2k_ts_power(1);
		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID, i2c_touch_devices_harry_elan, ARRAY_SIZE(i2c_touch_devices_harry_elan));
		#elif defined(CONFIG_TOUCHSCREEN_CYPRESS_CY8CTMA340)
		pr_info("-- CAP_TOUCH_DETECT is Cypress IC + Second Source Panel  --\n");
		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
								i2c_touch_devices_cypress_tma340,
								ARRAY_SIZE(i2c_touch_devices_cypress_tma340));
		#else
		pr_info("-- CAP_TOUCH_DETECT Low - Fail --\n");
		#endif
	}
	#endif
	//>>MelChang,[Harry] Add ELAN eKTF2040 and ILITEK ILI2013t touch panel IC

	/*++ Huize - 20110914 Register sensor device ++*/
	i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
							Sensor_devices_info,
							ARRAY_SIZE(Sensor_devices_info));
	/*-- Huize - 20110914 Register sensor device --*/

	/* keypad */
	//Mel, 2012/4/18, Enable Key GPIO. ++
	#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
	platform_device_register(&NanHu_button_device);
	#endif
	//Mel, 2012/4/18, Enable Key GPIO. --

	//Mel, 2012/4/18, Disable Key Matrix. ++
	#if 0
	platform_device_register(&kp_pdev);
	#endif
	//Mel, 2012/4/18, Disable Key Matrix. --

	/* headset */
	platform_device_register(&hs_pdev);

	/* LED: configure it as a pdm function */
	if (gpio_tlmm_config(GPIO_CFG(LED_GPIO_PDM, 3,
				GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE))
		pr_err("%s: gpio_tlmm_config for %d failed\n",
			__func__, LED_GPIO_PDM);
	else
		platform_device_register(&led_pdev);
	/* ++ Edison add led device ++ */
	#ifdef CONFIG_LEDS_CHIP_LM3533
	led_lm3533_hw_init();
	i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
							i2c_led_devices_LM3533,
							ARRAY_SIZE(i2c_led_devices_LM3533));
	#endif
	/* -- Edison add led device -- */

	/* Vibrator */
	//<<Skies, 2011/10/12 enable vibrator function
	//if (machine_is_msm7x27a_ffa() || machine_is_msm7625a_ffa()
	//				|| machine_is_msm8625_ffa())
	//>>Skies, 2011/10/12
		msm_init_pmic_vibrator();
}

开发者ID:Zoldyck07，项目名称:android_kernel_sony_msm7x27a，代码行数:94，代码来源:board-nanhu-io.c

示例2: mxc_board_init

/*!
 * Board specific initialization.
 */
static void __init mxc_board_init(void)
{
	mxc_ipu_data.di_clk[0] = clk_get(NULL, "ipu_di0_clk");
	mxc_ipu_data.di_clk[1] = clk_get(NULL, "ipu_di1_clk");
	mxc_ipu_data.csi_clk[0] = clk_get(NULL, "ssi_ext1_clk");
	mxc_spdif_data.spdif_core_clk = clk_get(NULL, "spdif_xtal_clk");
	clk_put(mxc_spdif_data.spdif_core_clk);

	mxcsdhc1_device.resource[2].start = gpio_to_irq(MX53_SMD_SD1_CD);
	mxcsdhc1_device.resource[2].end = gpio_to_irq(MX53_SMD_SD1_CD);

	mxc_cpu_common_init();
	mx53_smd_io_init();

	/* power off by sending shutdown command to da9053*/
	pm_power_off = wm831x_poweroff_system;
	mxc_register_device(&mxc_dma_device, NULL);
	mxc_register_device(&mxc_wdt_device, NULL);
	mxc_register_device(&mxcspi1_device, &mxcspi1_data);
	mxc_register_device(&mxci2c_devices[0], &mxci2c_data);
	mxc_register_device(&mxci2c_devices[1], &mxci2c_data);
	mxc_register_device(&mxci2c_devices[2], &mxci2c_data);
	mx53_smd_init_wm8325();

	mxc_register_device(&mxc_rtc_device, NULL);
	mxc_register_device(&mxc_ipu_device, &mxc_ipu_data);
	mxc_register_device(&mxc_ldb_device, &ldb_data);
	mxc_register_device(&mxc_tve_device, &tve_data);
	mxc_register_device(&mxcvpu_device, &mxc_vpu_data);
	mxc_register_device(&gpu_device, &gpu_data);
	mxc_register_device(&mxcscc_device, NULL);
	mxc_register_device(&mxc_dvfs_core_device, &dvfs_core_data);
	mxc_register_device(&busfreq_device, &bus_freq_data);
	mxc_register_device(&mxc_iim_device, &iim_data);
	mxc_register_device(&mxc_pwm1_device, &mxc_pwm1_platform_data);
	mxc_register_device(&mxc_pwm2_device, NULL);
	mxc_register_device(&mxc_pwm1_backlight_device, &mxc_pwm_backlight_data);
	/* Register mmc3(eMMC) first, make it's device number be 0 to
	 * avoid device number change by hotplug in SD(mmc1) card */
	mxc_register_device(&mxcsdhc3_device, &mmc3_data);
	mxc_register_device(&mxcsdhc1_device, &mmc1_data);
	mxc_register_device(&mxcsdhc2_device, &mmc2_data);
	mxc_register_device(&mxc_ssi1_device, NULL);
	mxc_register_device(&mxc_ssi2_device, NULL);
	mxc_register_device(&mxc_alsa_spdif_device, &mxc_spdif_data);
	mxc_register_device(&mxc_android_pmem_device, &android_pmem_data);
	mxc_register_device(&mxc_android_pmem_gpu_device,
				&android_pmem_gpu_data);
	mxc_register_device(&usb_mass_storage_device, &mass_storage_data);
	mxc_register_device(&usb_rndis_device, &rndis_data);
	mxc_register_device(&android_usb_device, &android_usb_data);
	mxc_register_device(&ahci_fsl_device, &sata_data);
	/* AHCI SATA PWR EN(DCDC_5V, DCDC_3V3_BB) on SATA bus */
	gpio_request(MX53_SMD_SATA_PWR_EN, "sata-pwr-en");
	gpio_direction_output(MX53_SMD_SATA_PWR_EN, 1);

	mxc_register_device(&mxc_fec_device, &fec_data);
	mxc_register_device(&mxc_ptp_device, NULL);
	/* ASRC is only available for MX53 TO2.0 */
	if (mx53_revision() >= IMX_CHIP_REVISION_2_0) {
		mxc_asrc_data.asrc_core_clk = clk_get(NULL, "asrc_clk");
		clk_put(mxc_asrc_data.asrc_core_clk);
		mxc_asrc_data.asrc_audio_clk = clk_get(NULL, "asrc_serial_clk");
		clk_put(mxc_asrc_data.asrc_audio_clk);
		mxc_register_device(&mxc_asrc_device, &mxc_asrc_data);
	}

	spi_device_init();

	i2c_register_board_info(1, mxc_i2c1_board_info,
				ARRAY_SIZE(mxc_i2c1_board_info));
	i2c_register_board_info(2, mxc_i2c2_board_info,
				ARRAY_SIZE(mxc_i2c2_board_info));

	mxc_register_device(&mxc_rt5621_device, &rt5621_data);
	mxc_register_device(&mxc_spdif_audio_device, &spdif_audio_data);
	mx5_set_otghost_vbus_func(mx53_gpio_usbotg_driver_vbus);
	mx5_usb_dr_init();
	mx5_usbh1_init();
	mxc_register_device(&mxc_v4l2_device, NULL);
	mxc_register_device(&mxc_v4l2out_device, NULL);
	mxc_register_device(&mxc_bt_rfkill, &mxc_bt_rfkill_data);
	smd_add_device_buttons();
	smd_add_device_battery();

}

开发者ID:onyx-intl，项目名称:t80_android_frameworks，代码行数:89，代码来源:mx53_smd.c

示例3: incrediblec_init

static void __init incrediblec_init(void)
{
	int ret;
	struct kobject *properties_kobj;

	printk("incrediblec_init() revision=%d, engineerid=%d\n", system_rev, engineerid);

	 msm_hw_reset_hook = incrediblec_reset;

	if (0 == engineerid || 0xF == engineerid) {
		mdp_pmem_pdata.start = MSM_PMEM_MDP_XA_BASE;
		android_pmem_adsp_pdata.start = MSM_PMEM_ADSP_XA_BASE;
                msm_kgsl_resources[1].start = MSM_GPU_MEM_XA_BASE;
                msm_kgsl_resources[1].end = MSM_GPU_MEM_XA_BASE + MSM_GPU_MEM_SIZE - 1;
	} else if (engineerid >= 3) {
		mdp_pmem_pdata.start = MSM_PMEM_MDP_BASE + MSM_MEM_128MB_OFFSET;
		android_pmem_adsp_pdata.start = MSM_PMEM_ADSP_BASE + MSM_MEM_128MB_OFFSET;
		msm_kgsl_resources[1].start = MSM_GPU_MEM_BASE;
		msm_kgsl_resources[1].end =  msm_kgsl_resources[1].start + MSM_GPU_MEM_SIZE - 1;
	}

	incrediblec_board_serialno_setup(board_serialno());

	OJ_BMA_power();

	msm_acpu_clock_init(&incrediblec_clock_data);

	perflock_init(&incrediblec_perflock_data);

#if defined(CONFIG_MSM_SERIAL_DEBUGGER)
	msm_serial_debug_init(MSM_UART1_PHYS, INT_UART1,
				&msm_device_uart1.dev, 1, INT_UART1_RX);
#endif

	bcm_bt_lpm_pdata.gpio_wake = INCREDIBLEC_GPIO_BT_CHIP_WAKE;
	config_gpio_table(bt_gpio_table_rev_CX, ARRAY_SIZE(bt_gpio_table_rev_CX));
	
	
	/* set the gpu power rail to manual mode so clk en/dis will not
	 * turn off gpu power, and hang it on resume */
	incrediblec_kgsl_power_rail_mode(0);
	incrediblec_kgsl_power(true);

	
#ifdef CONFIG_SPI_QSD
	msm_device_spi.dev.platform_data = &incrediblec_spi_pdata;
#endif	
	
	#ifdef CONFIG_SERIAL_MSM_HS
	msm_device_uart_dm1.dev.platform_data = &msm_uart_dm1_pdata;
	msm_device_uart_dm1.name = "msm_serial_hs";	/* for bcm */
	#endif

	incrediblec_config_uart_gpios();
	config_gpio_table(usb_phy_3v3_table, ARRAY_SIZE(usb_phy_3v3_table));
	config_gpio_table(camera_off_gpio_table,
		ARRAY_SIZE(camera_off_gpio_table));
	/*gpio_direction_output(INCREDIBLEC_GPIO_TP_LS_EN, 0);*/
	gpio_direction_output(INCREDIBLEC_GPIO_TP_EN, 0);

	incrediblec_audio_init();
#ifdef CONFIG_MICROP_COMMON
	incrediblec_microp_init();
#endif

	if (system_rev >= 2) {
		microp_data.num_functions   = ARRAY_SIZE(microp_functions_1);
		microp_data.microp_function = microp_functions_1;
	}

	platform_add_devices(devices, ARRAY_SIZE(devices));
	if (!opt_usb_h2w_sw) {
		msm_device_hsusb.dev.platform_data = &msm_hsusb_pdata;
	}	
	if (system_rev > 2) {
		incrediblec_atmel_ts_data[0].config_T9[7] = 33;
		incrediblec_atmel_ts_data[0].object_crc[0] = 0x2E;
		incrediblec_atmel_ts_data[0].object_crc[1] = 0x80;
		incrediblec_atmel_ts_data[0].object_crc[2] = 0xE0;
	}
	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));

	ret = incrediblec_init_mmc(system_rev);
	if (ret != 0)
		pr_crit("%s: Unable to initialize MMC\n", __func__);

	properties_kobj = kobject_create_and_add("board_properties", NULL);
	if (properties_kobj)
		ret = sysfs_create_group(properties_kobj,
				&incrediblec_properties_attr_group);
	if (!properties_kobj || ret)
		pr_err("failed to create board_properties\n");

	msm_init_pmic_vibrator();

}

开发者ID:Savaged-Zen，项目名称:Savaged-Zen-Inc，代码行数:96，代码来源:board-incrediblec.c

示例4: qrd7627a_add_io_devices

void __init qrd7627a_add_io_devices(void)
{
	int rc;

	/* touchscreen */
	if (machine_is_msm7627a_qrd1()) {
		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
					synaptic_i2c_clearpad3k,
					ARRAY_SIZE(synaptic_i2c_clearpad3k));
	} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
			machine_is_msm8625_evt()) {
		/* Use configuration data for EVT */
		if (machine_is_msm8625_evt()) {
			mxt_config_array[0].config = mxt_config_data_evt;
			mxt_config_array[0].config_length =
					ARRAY_SIZE(mxt_config_data_evt);
			mxt_platform_data.panel_maxy = 875;
			mxt_platform_data.need_calibration = true;
			mxt_vkey_setup();
		}

		rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_IRQ_GPIO, 0,
				GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE);
		if (rc) {
			pr_err("%s: gpio_tlmm_config for %d failed\n",
				__func__, MXT_TS_IRQ_GPIO);
		}

		rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_RESET_GPIO, 0,
				GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE);
		if (rc) {
			pr_err("%s: gpio_tlmm_config for %d failed\n",
				__func__, MXT_TS_RESET_GPIO);
		}

		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
					mxt_device_info,
					ARRAY_SIZE(mxt_device_info));
	} else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()
				|| machine_is_qrd_skud_prime()
				|| machine_is_msm8625q_skud()
				|| machine_is_msm8625q_evbd()) {
		ft5x06_touchpad_setup();
		/* evbd+ can support synaptic as well */
		if (machine_is_msm8625q_evbd() &&
			(socinfo_get_platform_type() == 0x13)) {
			/* for QPR EVBD+ with synaptic touch panel */
			/* TODO: Add  gpio request to the driver
				to support proper dynamic touch detection */
			gpio_tlmm_config(
				GPIO_CFG(CLEARPAD3000_ATTEN_GPIO_EVBD_PLUS, 0,
				GPIO_CFG_INPUT, GPIO_CFG_NO_PULL,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE);

			gpio_tlmm_config(
				GPIO_CFG(CLEARPAD3000_RESET_GPIO, 0,
				GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE);

			gpio_set_value(CLEARPAD3000_RESET_GPIO, 0);
			usleep(10000);
			gpio_set_value(CLEARPAD3000_RESET_GPIO, 1);
			usleep(50000);

			i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
				rmi4_i2c_devices,
				ARRAY_SIZE(rmi4_i2c_devices));
		}
		else {
			if (machine_is_msm8625q_evbd()) {
				mxt_config_array[0].config = mxt_config_data;
				mxt_config_array[0].config_length =
				ARRAY_SIZE(mxt_config_data);
				mxt_platform_data.panel_maxy = 875;
				mxt_platform_data.need_calibration = true;
				mxt_platform_data.irq_gpio = MXT_TS_EVBD_IRQ_GPIO;
				mxt_vkey_setup();

			rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_EVBD_IRQ_GPIO, 0,
						GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
						GPIO_CFG_8MA), GPIO_CFG_ENABLE);
			if (rc) {
				pr_err("%s: gpio_tlmm_config for %d failed\n",
						__func__, MXT_TS_EVBD_IRQ_GPIO);
			}

			rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_RESET_GPIO, 0,
						GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
						GPIO_CFG_8MA), GPIO_CFG_ENABLE);
			if (rc) {
				pr_err("%s: gpio_tlmm_config for %d failed\n",
						__func__, MXT_TS_RESET_GPIO);
			}

			i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
				mxt_device_info,
				ARRAY_SIZE(mxt_device_info));
			}
//.........这里部分代码省略.........

开发者ID:Astrali，项目名称:kernel_msm8625q_f1，代码行数:101，代码来源:board-msm7627a-io.c

示例5: sffsdr_init_i2c

static void __init sffsdr_init_i2c(void)
{
	davinci_init_i2c(&i2c_pdata);
	i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
}

开发者ID:1youhun1，项目名称:linux，代码行数:5，代码来源:board-sffsdr.c

示例6: msm7x2x_init

static void __init msm7x2x_init(void)
{
	msm7x2x_misc_init();

	/* Initialize regulators first so that other devices can use them */
	msm7x27a_init_regulators();

	/* Common functions for SURF/FFA/RUMI3 */
	msm_device_i2c_init();
	msm7x27a_init_ebi2();
	msm7x27a_cfg_uart2dm_serial();
#ifdef CONFIG_SERIAL_MSM_HS
	msm_uart_dm1_pdata.wakeup_irq = gpio_to_irq(UART1DM_RX_GPIO);
	msm_device_uart_dm1.dev.platform_data = &msm_uart_dm1_pdata;
#endif

#ifdef CONFIG_USB_MSM_OTG_72K
	msm_otg_pdata.swfi_latency =
		msm7x27a_pm_data
		[MSM_PM_SLEEP_MODE_RAMP_DOWN_AND_WAIT_FOR_INTERRUPT].latency;
	msm_device_otg.dev.platform_data = &msm_otg_pdata;
#endif
	msm_device_gadget_peripheral.dev.platform_data =
		&msm_gadget_pdata;
	msm7x27a_cfg_smsc911x();
	platform_add_devices(msm_footswitch_devices,
			msm_num_footswitch_devices);
	platform_add_devices(surf_ffa_devices,
			ARRAY_SIZE(surf_ffa_devices));
	/* Ensure ar6000pm device is registered before MMC/SDC */
	msm7x27a_init_ar6000pm();
#ifdef CONFIG_MMC_MSM
	msm7627a_init_mmc();
#endif
	msm_fb_add_devices();
#ifdef CONFIG_USB_EHCI_MSM_72K
	msm7x2x_init_host();
#endif

	msm_pm_set_platform_data(msm7x27a_pm_data,
				ARRAY_SIZE(msm7x27a_pm_data));
	BUG_ON(msm_pm_boot_init(&msm_pm_boot_pdata));

#if defined(CONFIG_I2C) && defined(CONFIG_GPIO_SX150X)
	register_i2c_devices();
#endif
#if defined(CONFIG_BT) && defined(CONFIG_MARIMBA_CORE)
	msm7627a_bt_power_init();
#endif
	if (machine_is_msm7625a_surf() || machine_is_msm7625a_ffa()) {
		atmel_ts_pdata.min_x = 0;
		atmel_ts_pdata.max_x = 480;
		atmel_ts_pdata.min_y = 0;
		atmel_ts_pdata.max_y = 320;
	}

	i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
		atmel_ts_i2c_info,
		ARRAY_SIZE(atmel_ts_i2c_info));

#if defined(CONFIG_MSM_CAMERA)
	msm7627a_camera_init();
#endif
	platform_device_register(&kp_pdev);
	platform_device_register(&hs_pdev);

	/* configure it as a pdm function*/
	if (gpio_tlmm_config(GPIO_CFG(LED_GPIO_PDM, 3,
				GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE))
		pr_err("%s: gpio_tlmm_config for %d failed\n",
			__func__, LED_GPIO_PDM);
	else
		platform_device_register(&led_pdev);

#ifdef CONFIG_MSM_RPC_VIBRATOR
	if (machine_is_msm7x27a_ffa() || machine_is_msm7625a_ffa())
		msm_init_pmic_vibrator();
#endif
	/*7x25a kgsl initializations*/
	msm7x25a_kgsl_3d0_init();
}

开发者ID:ddikodroid，项目名称:Finder-Kernel-Source-4.0，代码行数:82，代码来源:board-msm7x27a.c

示例7: ventana_sensors_init

int __init ventana_sensors_init(void)
{
	struct board_info BoardInfo;

#ifdef CONFIG_SENSORS_AK8975
	ventana_akm8975_init();
#endif
#ifdef CONFIG_MPU_SENSORS_MPU3050
	ventana_mpuirq_init();
#endif
	ventana_camera_init();

	ventana_nct1008_init();
	i2c_register_board_info(0, ventana_i2c0_board_info,
		ARRAY_SIZE(ventana_i2c0_board_info));

	i2c_register_board_info(2, ventana_i2c2_board_info,
		ARRAY_SIZE(ventana_i2c2_board_info));

	i2c_register_board_info(2, cap_i2c1_board_info,
                ARRAY_SIZE(cap_i2c1_board_info));

	i2c_register_board_info(2, light_i2c1_board_info,
		ARRAY_SIZE(light_i2c1_board_info));

	i2c_register_board_info(2, proximity_i2c1_board_info,
		ARRAY_SIZE(proximity_i2c1_board_info));
//+ ov5640 rear camera
	i2c_register_board_info(3, ventana_i2c3_board_info,
		ARRAY_SIZE(ventana_i2c3_board_info));
//-
//+ Front camera
	i2c_register_board_info(3, front_sensor_i2c3_board_info,
		ARRAY_SIZE(front_sensor_i2c3_board_info));
//-
//+ mi5140 rear camera
	i2c_register_board_info(3, rear_sensor2_i2c3_board_info,
		ARRAY_SIZE(rear_sensor2_i2c3_board_info));
//-

	i2c_register_board_info(4, ventana_i2c4_board_info,
		ARRAY_SIZE(ventana_i2c4_board_info));

//ddebug 	i2c_register_board_info(7, ventana_i2c7_board_info,
//ddebug 		ARRAY_SIZE(ventana_i2c7_board_info));

	i2c_register_board_info(8, ventana_i2c8_board_info,
		ARRAY_SIZE(ventana_i2c8_board_info));


#ifdef CONFIG_MPU_SENSORS_MPU3050
	i2c_register_board_info(0, mpu3050_i2c0_boardinfo,
		ARRAY_SIZE(mpu3050_i2c0_boardinfo));
#endif

	return 0;
}

开发者ID:ViViDboarder，项目名称:android_kernel_TF101，代码行数:57，代码来源:board-ventana-sensors.c

示例8: vpac270_pmic_init

static void __init vpac270_pmic_init(void)
{
	i2c_register_board_info(1, ARRAY_AND_SIZE(vpac270_pi2c_board_info));
}

开发者ID:0xroot，项目名称:Blackphone-BP1-Kernel，代码行数:4，代码来源:vpac270.c

示例9: income_i2c_init

static void __init income_i2c_init(void)
{
	pxa_set_i2c_info(NULL);
	pxa27x_set_i2c_power_info(NULL);
	i2c_register_board_info(0, ARRAY_AND_SIZE(income_i2c_devs));
}

开发者ID:007kumarraja，项目名称:rockchip-rk3188-mk908，代码行数:6，代码来源:colibri-pxa270-income.c

示例10: ap4evb_init


//.........这里部分代码省略.........
	gpio_request(GPIO_FN_FSIAILR,	NULL);
	gpio_request(GPIO_FN_FSIAISLD,	NULL);
	gpio_request(GPIO_FN_FSIAOSLD,	NULL);
	gpio_request(GPIO_PORT161,	NULL);
	gpio_direction_output(GPIO_PORT161, 0); /* slave */

	gpio_request(GPIO_PORT9, NULL);
	gpio_request(GPIO_PORT10, NULL);
	gpio_no_direction(GPIO_PORT9CR);  /* FSIAOBT needs no direction */
	gpio_no_direction(GPIO_PORT10CR); /* FSIAOLR needs no direction */

	/* card detect pin for MMC slot (CN7) */
	gpio_request(GPIO_PORT41, NULL);
	gpio_direction_input(GPIO_PORT41);

	/* setup FSI2 port B (HDMI) */
	gpio_request(GPIO_FN_FSIBCK, NULL);
	__raw_writew(__raw_readw(USCCR1) & ~(1 << 6), USCCR1); /* use SPDIF */

	/* set SPU2 clock to 119.6 MHz */
	clk = clk_get(NULL, "spu_clk");
	if (!IS_ERR(clk)) {
		clk_set_rate(clk, clk_round_rate(clk, 119600000));
		clk_put(clk);
	}

	/*
	 * set irq priority, to avoid sound chopping
	 * when NFS rootfs is used
	 *  FSI(3) > SMSC911X(2)
	 */
	intc_set_priority(IRQ_FSI, 3);

	i2c_register_board_info(0, i2c0_devices,
				ARRAY_SIZE(i2c0_devices));

	i2c_register_board_info(1, i2c1_devices,
				ARRAY_SIZE(i2c1_devices));

#ifdef CONFIG_AP4EVB_QHD

	/*
	 * For QHD Panel (MIPI-DSI, CONFIG_AP4EVB_QHD=y) and
	 * IRQ28 for Touch Panel, set dip switches S3, S43 as OFF, ON.
	 */

	/* enable KEYSC */
	gpio_request(GPIO_FN_KEYOUT0, NULL);
	gpio_request(GPIO_FN_KEYOUT1, NULL);
	gpio_request(GPIO_FN_KEYOUT2, NULL);
	gpio_request(GPIO_FN_KEYOUT3, NULL);
	gpio_request(GPIO_FN_KEYOUT4, NULL);
	gpio_request(GPIO_FN_KEYIN0_136, NULL);
	gpio_request(GPIO_FN_KEYIN1_135, NULL);
	gpio_request(GPIO_FN_KEYIN2_134, NULL);
	gpio_request(GPIO_FN_KEYIN3_133, NULL);
	gpio_request(GPIO_FN_KEYIN4,     NULL);

	/* enable TouchScreen */
	set_irq_type(IRQ28, IRQ_TYPE_LEVEL_LOW);

	tsc_device.irq = IRQ28;
	i2c_register_board_info(1, &tsc_device, 1);

	/* LCDC0 */
	lcdc_info.clock_source			= LCDC_CLK_PERIPHERAL;

开发者ID:Adjustxx，项目名称:Savaged-Zen，代码行数:67，代码来源:board-ap4evb.c

示例11: vpac270_rtc_init

static void __init vpac270_rtc_init(void)
{
	i2c_register_board_info(0, ARRAY_AND_SIZE(vpac270_i2c_devs));
}

开发者ID:0xroot，项目名称:Blackphone-BP1-Kernel，代码行数:4，代码来源:vpac270.c

示例12: mxc_board_init

/*!
 * Board specific initialization.
 */
static void __init mxc_board_init(void)
{
	mxc_ipu_data.di_clk[0] = clk_get(NULL, "ipu_di0_clk");
	mxc_ipu_data.di_clk[1] = clk_get(NULL, "ipu_di1_clk");
	mxc_ipu_data.csi_clk[0] = clk_get(NULL, "csi_mclk1");
	mxc_ipu_data.csi_clk[1] = clk_get(NULL, "csi_mclk2");

	mxc_spdif_data.spdif_core_clk = clk_get(NULL, "spdif_xtal_clk");
	clk_put(mxc_spdif_data.spdif_core_clk);

	spdif_audio_data.ext_ram_clk = clk_get(NULL, "emi_fast_clk");
	clk_put(spdif_audio_data.ext_ram_clk);

	sgtl5000_data.ext_ram_clk = clk_get(NULL, "emi_fast_clk");
	clk_put(sgtl5000_data.ext_ram_clk);

	/* SD card detect irqs */
	mxcsdhc2_device.resource[2].start = gpio_to_irq(BABBAGE_SD2_CD_2_5);
	mxcsdhc2_device.resource[2].end = gpio_to_irq(BABBAGE_SD2_CD_2_5);
	mxcsdhc1_device.resource[2].start = gpio_to_irq(BABBAGE_SD1_CD);
	mxcsdhc1_device.resource[2].end = gpio_to_irq(BABBAGE_SD1_CD);

	mxc_cpu_common_init();
	mx51_babbage_io_init();

	mxc_register_device(&mxc_dma_device, NULL);
	mxc_register_device(&mxc_wdt_device, NULL);
	mxc_register_device(&mxcspi1_device, &mxcspi1_data);
	mxc_register_device(&mxci2c_devices[0], &mxci2c_data);
	mxc_register_device(&mxci2c_devices[1], &mxci2c_data);
	mxc_register_device(&mxci2c_hs_device, &mxci2c_hs_data);
	mxc_register_device(&mxc_rtc_device, NULL);
	mxc_register_device(&mxc_w1_master_device, &mxc_w1_data);
	mxc_register_device(&mxc_ipu_device, &mxc_ipu_data);
	mxc_register_device(&mxc_tve_device, &tve_data);
	if (!mxc_fuse_get_vpu_status())
		mxc_register_device(&mxcvpu_device, &mxc_vpu_data);
	if (!mxc_fuse_get_gpu_status())
		mxc_register_device(&gpu_device, &gpu_data);
	mxc_register_device(&mxcscc_device, NULL);
	mxc_register_device(&mx51_lpmode_device, NULL);
	mxc_register_device(&busfreq_device, &bus_freq_data);
	mxc_register_device(&sdram_autogating_device, NULL);
	mxc_register_device(&mxc_dvfs_core_device, &dvfs_core_data);
	mxc_register_device(&mxc_dvfs_per_device, &dvfs_per_data);
	mxc_register_device(&mxc_iim_device, &iim_data);
	mxc_register_device(&mxc_pwm1_device, NULL);
	mxc_register_device(&mxc_pwm1_backlight_device,
		&mxc_pwm_backlight_data);
	mxc_register_device(&mxc_keypad_device, &keypad_plat_data);
	mxc_register_device(&mxcsdhc1_device, &mmc1_data);
	mxc_register_device(&mxcsdhc2_device, &mmc2_data);
	mxc_register_device(&mxc_ssi1_device, NULL);
	mxc_register_device(&mxc_ssi2_device, NULL);
	mxc_register_device(&mxc_ssi3_device, NULL);
	mxc_register_device(&mxc_alsa_spdif_device, &mxc_spdif_data);
	mxc_register_device(&mxc_android_pmem_device, &android_pmem_data);
	mxc_register_device(&mxc_android_pmem_gpu_device,
					&android_pmem_gpu_data);
	mxc_register_device(&usb_mass_storage_device, &mass_storage_data);
	mxc_register_device(&usb_rndis_device, &rndis_data);
	mxc_register_device(&android_usb_device, &android_usb_data);
	mxc_register_device(&mxc_fec_device, NULL);
	mxc_register_device(&mxc_v4l2_device, NULL);
	mxc_register_device(&mxc_v4l2out_device, NULL);
	mxc_register_device(&mxc_powerkey_device, &pwrkey_data);
	mxc_register_device(&mxc_spdif_audio_device, &spdif_audio_data);

	mx51_babbage_init_mc13892();

	if (board_is_rev(BOARD_REV_2))
		/* BB2.5 */
		spi_register_board_info(mxc_dataflash_device,
					ARRAY_SIZE(mxc_dataflash_device));
	else
		/* BB2.0 */
		spi_register_board_info(mxc_spi_nor_device,
					ARRAY_SIZE(mxc_spi_nor_device));

	i2c_register_board_info(0, mxc_i2c0_board_info,
				ARRAY_SIZE(mxc_i2c0_board_info));
	i2c_register_board_info(1, mxc_i2c1_board_info,
				ARRAY_SIZE(mxc_i2c1_board_info));


	vga_data.core_reg = NULL;
	vga_data.io_reg = NULL;
	vga_data.analog_reg = NULL;

	i2c_register_board_info(3, mxc_i2c_hs_board_info,
				ARRAY_SIZE(mxc_i2c_hs_board_info));

	pm_power_off = mxc_power_off;

	sgtl5000_data.sysclk = 26000000;

	gpio_request(BABBAGE_AUDAMP_STBY, "audioamp-stdby");
//.........这里部分代码省略.........

开发者ID:pocketbook，项目名称:801，代码行数:101，代码来源:mx51_babbage.c

示例13: pcm037_init

static void __init pcm037_init(void)
{
	int ret;

	imx31_soc_init();

	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));

	mxc_iomux_set_gpr(MUX_PGP_UH2, 1);

	mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins),
			"pcm037");

#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS \
		| PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)

	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); 
	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); 
	mxc_iomux_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG);	
	mxc_iomux_set_pad(MX31_PIN_STXD6, H2_PAD_CFG);	
	mxc_iomux_set_pad(MX31_PIN_SFS3, H2_PAD_CFG);	
	mxc_iomux_set_pad(MX31_PIN_SCK3, H2_PAD_CFG);	
	mxc_iomux_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG);	
	mxc_iomux_set_pad(MX31_PIN_STXD3, H2_PAD_CFG);	

	if (pcm037_variant() == PCM037_EET)
		mxc_iomux_setup_multiple_pins(pcm037_uart1_pins,
			ARRAY_SIZE(pcm037_uart1_pins), "pcm037_uart1");
	else
		mxc_iomux_setup_multiple_pins(pcm037_uart1_handshake_pins,
			ARRAY_SIZE(pcm037_uart1_handshake_pins),
			"pcm037_uart1");

	platform_add_devices(devices, ARRAY_SIZE(devices));

	imx31_add_imx2_wdt(NULL);
	imx31_add_imx_uart0(&uart_pdata);
	
	imx31_add_imx_uart1(&uart_pdata);
	imx31_add_imx_uart2(&uart_pdata);

	imx31_add_mxc_w1(NULL);

	
	ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1), "lan9217-irq");
	if (ret)
		pr_warning("could not get LAN irq gpio\n");
	else {
		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
		platform_device_register(&pcm037_eth);
	}


	
	i2c_register_board_info(1, pcm037_i2c_devices,
			ARRAY_SIZE(pcm037_i2c_devices));

	imx31_add_imx_i2c1(&pcm037_i2c1_data);
	imx31_add_imx_i2c2(&pcm037_i2c2_data);

	imx31_add_mxc_nand(&pcm037_nand_board_info);
	imx31_add_mxc_mmc(0, &sdhc_pdata);
	imx31_add_ipu_core(&mx3_ipu_data);
	imx31_add_mx3_sdc_fb(&mx3fb_pdata);

	
	
	ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_CSI_D5), "mt9t031-power");
	if (!ret)
		gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_CSI_D5), 1);
	else
		iclink_mt9t031.power = NULL;

	pcm037_init_camera();

	platform_device_register(&pcm970_sja1000);

	if (otg_mode_host) {
		otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
				ULPI_OTG_DRVVBUS_EXT);
		if (otg_pdata.otg)
			imx31_add_mxc_ehci_otg(&otg_pdata);
	}

	usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
			ULPI_OTG_DRVVBUS_EXT);
	if (usbh2_pdata.otg)
		imx31_add_mxc_ehci_hs(2, &usbh2_pdata);

	if (!otg_mode_host)
		imx31_add_fsl_usb2_udc(&otg_device_pdata);

}

开发者ID:Blackburn29，项目名称:PsycoKernel，代码行数:97，代码来源:mach-pcm037.c

示例14: qrd7627a_add_io_devices

void __init qrd7627a_add_io_devices(void)
{
	int rc;

	/* touchscreen */
	if (machine_is_msm7627a_qrd1()) {
		//20120507-Added by Jordan , it is no used for msm7627a
		#if defined(CONFIG_TOUCHSCREEN_SYNAPTICS_RMI4_I2C) || \
		defined(CONFIG_TOUCHSCREEN_SYNAPTICS_RMI4_I2C_MODULE)
		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
					synaptic_i2c_clearpad3k,
					ARRAY_SIZE(synaptic_i2c_clearpad3k));
		#endif
	} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
			machine_is_msm8625_evt()) {
		/* Use configuration data for EVT */
		if (machine_is_msm8625_evt()) {
			mxt_config_array[0].config = mxt_config_data_evt;
			mxt_config_array[0].config_length =
					ARRAY_SIZE(mxt_config_data_evt);
			mxt_platform_data.panel_maxy = 875;
			mxt_platform_data.need_calibration = true;
			mxt_vkey_setup();
		}

		rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_IRQ_GPIO, 0,
				GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE);
		if (rc) {
			pr_err("%s: gpio_tlmm_config for %d failed\n",
				__func__, MXT_TS_IRQ_GPIO);
		}

		rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_RESET_GPIO, 0,
				GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
				GPIO_CFG_8MA), GPIO_CFG_ENABLE);
		if (rc) {
			pr_err("%s: gpio_tlmm_config for %d failed\n",
				__func__, MXT_TS_RESET_GPIO);
		}

		i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
					mxt_device_info,
					ARRAY_SIZE(mxt_device_info));
	} else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) {
		#ifdef CONFIG_TOUCHSCREEN_FT5X06 //20120507-Jordan
		ft5x06_touchpad_setup();
		#endif
	}

	/* headset */
	platform_device_register(&hs_pdev);

	/* vibrator */
#ifdef CONFIG_MSM_RPC_VIBRATOR
	msm_init_pmic_vibrator();
#endif

	/* keypad */
	if (machine_is_msm8625_evt())
		kp_matrix_info_8625.keymap = keymap_8625_evt;

	if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
			machine_is_msm8625_evt())
		platform_device_register(&kp_pdev_8625);
	else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7())
		platform_device_register(&kp_pdev_sku3);

	/* leds */
	if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
						machine_is_msm8625_evt()) {
		platform_device_register(&pmic_mpp_leds_pdev);
		platform_device_register(&tricolor_leds_pdev);
	}
}

开发者ID:Zoldyck07，项目名称:android_kernel_sony_msm7x27a，代码行数:75，代码来源:board-nanhu-io.c

示例15: axp_board_init


//.........这里部分代码省略.........

        ret = script_parser_fetch("target", "dcdc2_vol", &dcdc2_vol, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            dcdc2_vol = 1400;
        }
        ret = script_parser_fetch("target", "dcdc3_vol", &dcdc3_vol, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            dcdc3_vol = 1250;
        }
        ret = script_parser_fetch("target", "ldo2_vol", &ldo2_vol, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            ldo2_vol = 3000;
        }
        ret = script_parser_fetch("target", "ldo3_vol", &ldo3_vol, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            ldo3_vol = 2800;
        }
        ret = script_parser_fetch("target", "ldo4_vol", &ldo4_vol, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            ldo4_vol = 2800;
        }

				ret = script_parser_fetch("pmu_para", "pmu_pekoff_time", &pmu_pekoff_time, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            pmu_pekoff_time = 6000;
        }
        ret = script_parser_fetch("pmu_para", "pmu_pekoff_en", &pmu_pekoff_en, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            pmu_pekoff_en   = 1;
        }
        ret = script_parser_fetch("pmu_para", "pmu_peklong_time", &pmu_peklong_time, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            pmu_peklong_time = 1500;
        }
        ret = script_parser_fetch("pmu_para", "pmu_pwrok_time", &pmu_pwrok_time, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
           pmu_pwrok_time    = 64;
        }
        ret = script_parser_fetch("pmu_para", "pmu_pwrnoe_time", &pmu_pwrnoe_time, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            pmu_pwrnoe_time = 2000;
        }
        ret = script_parser_fetch("pmu_para", "pmu_intotp_en", &pmu_intotp_en, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            pmu_intotp_en = 1;
        }   
        ret = script_parser_fetch("pmu_para", "pmu_pekon_time", &pmu_pekon_time, sizeof(int));
        if (ret)
        {
            printk("axp driver uning configuration failed(%d)\n", __LINE__);
            pmu_pekon_time = 1000;
        }           

        axp_regl_init_data[1].constraints.state_standby.uV = ldo2_vol * 1000;
        axp_regl_init_data[2].constraints.state_standby.uV = ldo3_vol * 1000;
        axp_regl_init_data[3].constraints.state_standby.uV = ldo4_vol * 1000;
        axp_regl_init_data[5].constraints.state_standby.uV = dcdc2_vol * 1000;
        axp_regl_init_data[6].constraints.state_standby.uV = dcdc3_vol * 1000;
        battery_data.voltage_max_design = pmu_init_chgvol;
        battery_data.voltage_min_design = pmu_pwroff_vol;
        battery_data.energy_full_design = pmu_battery_cap;
        axp_sply_init_data.chgcur = pmu_init_chgcur;
        axp_sply_init_data.chgvol = pmu_init_chgvol;
        axp_sply_init_data.chgend = pmu_init_chgend_rate;
        axp_sply_init_data.chgen = pmu_init_chg_enabled;
        axp_sply_init_data.sample_time = pmu_init_adc_freq;
        axp_sply_init_data.chgpretime = pmu_init_chg_pretime;
        axp_sply_init_data.chgcsttime = pmu_init_chg_csttime;
        axp_mfd_i2c_board_info[0].addr = pmu_twi_addr;
        axp_mfd_i2c_board_info[0].irq = pmu_irq_id;

        return i2c_register_board_info(pmu_twi_id, axp_mfd_i2c_board_info,
				ARRAY_SIZE(axp_mfd_i2c_board_info));
    }
    else
        return -1;

}

开发者ID:godark，项目名称:A10-Linux-2.6.36，代码行数:101，代码来源:axp20-board.c

示例16: ap325rxa_devices_setup

static int __init ap325rxa_devices_setup(void)
{
	/* LD3 and LD4 LEDs */
	gpio_request(GPIO_PTX5, NULL); /* RUN */
	gpio_direction_output(GPIO_PTX5, 1);
	gpio_export(GPIO_PTX5, 0);

	gpio_request(GPIO_PTX4, NULL); /* INDICATOR */
	gpio_direction_output(GPIO_PTX4, 0);
	gpio_export(GPIO_PTX4, 0);

	/* SW1 input */
	gpio_request(GPIO_PTF7, NULL); /* MODE */
	gpio_direction_input(GPIO_PTF7);
	gpio_export(GPIO_PTF7, 0);

	/* LCDC */
	clk_always_enable("mstp200");
	gpio_request(GPIO_FN_LCDD15, NULL);
	gpio_request(GPIO_FN_LCDD14, NULL);
	gpio_request(GPIO_FN_LCDD13, NULL);
	gpio_request(GPIO_FN_LCDD12, NULL);
	gpio_request(GPIO_FN_LCDD11, NULL);
	gpio_request(GPIO_FN_LCDD10, NULL);
	gpio_request(GPIO_FN_LCDD9, NULL);
	gpio_request(GPIO_FN_LCDD8, NULL);
	gpio_request(GPIO_FN_LCDD7, NULL);
	gpio_request(GPIO_FN_LCDD6, NULL);
	gpio_request(GPIO_FN_LCDD5, NULL);
	gpio_request(GPIO_FN_LCDD4, NULL);
	gpio_request(GPIO_FN_LCDD3, NULL);
	gpio_request(GPIO_FN_LCDD2, NULL);
	gpio_request(GPIO_FN_LCDD1, NULL);
	gpio_request(GPIO_FN_LCDD0, NULL);
	gpio_request(GPIO_FN_LCDLCLK_PTR, NULL);
	gpio_request(GPIO_FN_LCDDCK, NULL);
	gpio_request(GPIO_FN_LCDVEPWC, NULL);
	gpio_request(GPIO_FN_LCDVCPWC, NULL);
	gpio_request(GPIO_FN_LCDVSYN, NULL);
	gpio_request(GPIO_FN_LCDHSYN, NULL);
	gpio_request(GPIO_FN_LCDDISP, NULL);
	gpio_request(GPIO_FN_LCDDON, NULL);

	/* LCD backlight */
	gpio_request(GPIO_PTS3, NULL);
	gpio_direction_output(GPIO_PTS3, 1);

	/* CEU */
	clk_always_enable("mstp203");
	gpio_request(GPIO_FN_VIO_CLK2, NULL);
	gpio_request(GPIO_FN_VIO_VD2, NULL);
	gpio_request(GPIO_FN_VIO_HD2, NULL);
	gpio_request(GPIO_FN_VIO_FLD, NULL);
	gpio_request(GPIO_FN_VIO_CKO, NULL);
	gpio_request(GPIO_FN_VIO_D15, NULL);
	gpio_request(GPIO_FN_VIO_D14, NULL);
	gpio_request(GPIO_FN_VIO_D13, NULL);
	gpio_request(GPIO_FN_VIO_D12, NULL);
	gpio_request(GPIO_FN_VIO_D11, NULL);
	gpio_request(GPIO_FN_VIO_D10, NULL);
	gpio_request(GPIO_FN_VIO_D9, NULL);
	gpio_request(GPIO_FN_VIO_D8, NULL);

	gpio_request(GPIO_PTZ7, NULL);
	gpio_direction_output(GPIO_PTZ7, 0); /* OE_CAM */
	gpio_request(GPIO_PTZ6, NULL);
	gpio_direction_output(GPIO_PTZ6, 0); /* STBY_CAM */
	gpio_request(GPIO_PTZ5, NULL);
	gpio_direction_output(GPIO_PTZ5, 1); /* RST_CAM */
	gpio_request(GPIO_PTZ4, NULL);
	gpio_direction_output(GPIO_PTZ4, 0); /* SADDR */

	ctrl_outw(ctrl_inw(PORT_MSELCRB) & ~0x0001, PORT_MSELCRB);

	/* FLCTL */
	gpio_request(GPIO_FN_FCE, NULL);
	gpio_request(GPIO_FN_NAF7, NULL);
	gpio_request(GPIO_FN_NAF6, NULL);
	gpio_request(GPIO_FN_NAF5, NULL);
	gpio_request(GPIO_FN_NAF4, NULL);
	gpio_request(GPIO_FN_NAF3, NULL);
	gpio_request(GPIO_FN_NAF2, NULL);
	gpio_request(GPIO_FN_NAF1, NULL);
	gpio_request(GPIO_FN_NAF0, NULL);
	gpio_request(GPIO_FN_FCDE, NULL);
	gpio_request(GPIO_FN_FOE, NULL);
	gpio_request(GPIO_FN_FSC, NULL);
	gpio_request(GPIO_FN_FWE, NULL);
	gpio_request(GPIO_FN_FRB, NULL);

	ctrl_outw(0, PORT_HIZCRC);
	ctrl_outw(0xFFFF, PORT_DRVCRA);
	ctrl_outw(0xFFFF, PORT_DRVCRB);

	platform_resource_setup_memory(&ceu_device, "ceu", 4 << 20);

	i2c_register_board_info(0, ap325rxa_i2c_devices,
				ARRAY_SIZE(ap325rxa_i2c_devices));

	return platform_add_devices(ap325rxa_devices,
//.........这里部分代码省略.........

开发者ID:E-LLP，项目名称:n900，代码行数:101，代码来源:board-ap325rxa.c

示例17: ip7500av_init

/*
 * ip7500av_init
 *	Called to add the devices which we have on this board
 */
static int __init ip7500av_init(void)
{
	struct platform_device *audio_dev;
	struct platform_device *audio_dev2;
	struct ubi32_cs4384_platform_data *cs4384_pd;

	if (ubicom32_flash_single_init()) {
		printk(KERN_ERR "%s: could not initialize flash controller\n", __FUNCTION__);
	}

	board_init();

	ubi_gpio_init();

	/*
	 * Start the flash driver
	 */
	ubicom32_flash_single_init();

	vdc_tio_init(NULL);

	printk(KERN_INFO "%s: registering device resources\n", __FUNCTION__);
	platform_add_devices(ip7500av_devices, ARRAY_SIZE(ip7500av_devices));

	/*
	 * CS4384 DAC
	 */
	audio_dev = audio_device_alloc("snd-ubi32-cs4384", "audio", "audio-i2sout",
			sizeof(struct ubi32_cs4384_platform_data));
	if (audio_dev) {
		/*
		 * Attempt to figure out a good divisor.  This will only work
		 * assuming the core frequency is compatible.
		 */
		int i;
		unsigned int freq = processor_frequency();
		for (i = 0; i < ARRAY_SIZE(ip7500av_cs4384_mclk_entries); i++) {
			unsigned int div;
			unsigned int rate = ip7500av_cs4384_mclk_entries[i].rate / 1000;
			div = ((freq / rate) + 500) / 1000;
			ip7500av_cs4384_mclk_entries[i].div = div;
			printk("CS4384 mclk %d rate %u000Hz div %u act %u\n", i, rate, div, freq / div);
		}

		cs4384_pd = audio_device_priv(audio_dev);
		cs4384_pd->mclk_src = UBI32_CS4384_MCLK_PWM_0;
		cs4384_pd->n_mclk = ARRAY_SIZE(ip7500av_cs4384_mclk_entries);
		cs4384_pd->mclk_entries = ip7500av_cs4384_mclk_entries;
		ip7500av_i2c_board_info[0].platform_data = audio_dev;

		/*
		 * Reset the DAC
		 */
		if (gpio_request(GPIO_RF_4, "DAC Reset") == 0) {
			gpio_direction_output(GPIO_RF_4, 0);
			udelay(1);
			gpio_direction_output(GPIO_RF_4, 1);
		} else {
			printk("Unable to request DAC reset GPIO\n");
		}
	}

	/*
	 * SPDIF port
	 */
	audio_dev2 = audio_device_alloc("snd-ubi32-generic", "audio", "audio-spdifout", 0);
	if (audio_dev2) {
		platform_device_register(audio_dev2);
	}

	/*
	 * Register all of the devices which sit on the I2C bus
	 */
	printk(KERN_INFO "%s: registering i2c resources\n", __FUNCTION__);
	i2c_register_board_info(0, ip7500av_i2c_board_info, ARRAY_SIZE(ip7500av_i2c_board_info));

	printk(KERN_INFO "IP7500 Audio/Video Board\n");
	return 0;
}

开发者ID:patrick-ken，项目名称:MyNet_N900，代码行数:83，代码来源:board-ip7500av.c

示例18: nslu2_init

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ i2c_smbus_write_i2c_block_data函数代码示例发布时间：2022-05-30

C++ i2c_read_reg函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19234|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：10000|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8331|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8701|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8646|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9668|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8632|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8005|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8666|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7540|2022-11-06

扫描微信二维码

查看手机版网站

随时了解更新最新资讯

139-2527-9053

在线客服（服务时间 9:00～18:00）

在线QQ客服

地址：深圳市南山区西丽大学城创智工业园

电邮：jeky_zhao#qq.com

移动电话：139-2527-9053

客服电话

电子邮件

C++ i2c_register_board_info函数代码示例

示例1: msm7627a_add_io_devices

示例2: mxc_board_init

示例3: incrediblec_init

示例4: qrd7627a_add_io_devices

示例5: sffsdr_init_i2c

示例6: msm7x2x_init

示例7: ventana_sensors_init

示例8: vpac270_pmic_init

示例9: income_i2c_init

示例10: ap4evb_init

示例11: vpac270_rtc_init

示例12: mxc_board_init

示例13: pcm037_init

示例14: qrd7627a_add_io_devices

示例15: axp_board_init

示例16: ap325rxa_devices_setup

示例17: ip7500av_init

示例18: nslu2_init

请发表评论

全部评论

上一篇：

下一篇：

Delphi 日志记录和查看

krishnaik06/Machine-Learning-in-90-days

armancodv/building-energy-model-matlab:

美元符号为什么是“$”

FGRibreau/import-tweets-to-mastodon: How

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053