static int gpio_keys_suspend(struct device *dev)
{
	struct gpio_keys_drvdata *ddata = dev_get_drvdata(dev);
	int i;

	if (device_may_wakeup(dev)) {
		for (i = 0; i < ddata->n_buttons; i++) {
			struct gpio_button_data *bdata = &ddata->data[i];
			if (bdata->button->wakeup)
				enable_irq_wake(bdata->irq);
		}
#ifdef CONFIG_SENSORS_HALL
	if(ddata->gpio_flip_cover != 0) {
#ifdef CONFIG_SENSORS_HALL_IRQ_CTRL
		if (!ddata->cover_state && ddata->gsm_area)
			disable_irq_wake(ddata->irq_flip_cover);
		else
#endif
			enable_irq_wake(ddata->irq_flip_cover);
	}
#endif
	}
		return 0;
}

/**
 * acpi_subsys_prepare - Prepare device for system transition to a sleep state.
 * @dev: Device to prepare.
 */
int acpi_subsys_prepare(struct device *dev)
{
	struct acpi_device *adev = ACPI_COMPANION(dev);
	u32 sys_target;
	int ret, state;

	ret = pm_generic_prepare(dev);
	if (ret < 0)
		return ret;

	if (!adev || !pm_runtime_suspended(dev)
	    || device_may_wakeup(dev) != !!adev->wakeup.prepare_count)
		return 0;

	sys_target = acpi_target_system_state();
	if (sys_target == ACPI_STATE_S0)
		return 1;

	if (adev->power.flags.dsw_present)
		return 0;

	ret = acpi_dev_pm_get_state(dev, adev, sys_target, NULL, &state);
	return !ret && state == adev->power.state;
}

static int serial_omap_runtime_suspend(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	if (!up)
		return -EINVAL;

	/*
	* When using 'no_console_suspend', the console UART must not be
	* suspended. Since driver suspend is managed by runtime suspend,
	* preventing runtime suspend (by returning error) will keep device
	* active during suspend.
	*/
	if (up->is_suspending && !console_suspend_enabled &&
	    uart_console(&up->port))
		return -EBUSY;

	up->context_loss_cnt = serial_omap_get_context_loss_count(up);

	if (device_may_wakeup(dev)) {
		if (!up->wakeups_enabled) {
			serial_omap_enable_wakeup(up, true);
			up->wakeups_enabled = true;
		}
	} else {
		if (up->wakeups_enabled) {
			serial_omap_enable_wakeup(up, false);
			up->wakeups_enabled = false;
		}
	}

	up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
	schedule_work(&up->qos_work);

	return 0;
}

/**
* hsi_runtime_suspend - Prepare HSI for low power : device will not process data and will
    not communicate with the CPU
* @dev - reference to the hsi device.
*
* Return value : -EBUSY or -EAGAIN if device is busy and still operational
*
*/
int hsi_runtime_suspend(struct device *dev)
{
	struct platform_device *pd = to_platform_device(dev);
	struct hsi_dev *hsi_ctrl = platform_get_drvdata(pd);
	struct hsi_platform_data *pdata = hsi_ctrl->dev->platform_data;
	int port, i;

	dev_dbg(dev, "%s\n", __func__);

	if (!hsi_ctrl->clock_enabled)
		dev_warn(dev, "Warning: clock status mismatch vs runtime PM\n");

	/* Put HSR into SLEEP mode to force ACREADY to low while HSI is idle */
	for (port = 1; port <= pdata->num_ports; port++) {
		hsi_outl_and(HSI_HSR_MODE_MODE_VAL_SLEEP, hsi_ctrl->base,
						HSI_HSR_MODE_REG(port));
	}

	/* Save context */
	hsi_save_ctx(hsi_ctrl);

	hsi_ctrl->clock_enabled = false;

	/* HSI is going to IDLE, it needs IO wakeup mechanism enabled */
	if (device_may_wakeup(dev))
		for (i = 0; i < hsi_ctrl->max_p; i++)
			pdata->wakeup_enable(hsi_ctrl->hsi_port[i].port_number);
	else
		for (i = 0; i < hsi_ctrl->max_p; i++)
			pdata->wakeup_disable(
				hsi_ctrl->hsi_port[i].port_number);

	/* HSI is now ready to be put in low power state */

	return 0;
}

static int serial_omap_runtime_suspend(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);
	struct omap_uart_port_info *pdata = dev->platform_data;

	if (!up)
		return -EINVAL;

	if (!pdata || !pdata->enable_wakeup)
		return 0;

	if (pdata->get_context_loss_count)
		up->context_loss_cnt = pdata->get_context_loss_count(dev);

	if (device_may_wakeup(dev)) {
		if (!up->wakeups_enabled) {
			pdata->enable_wakeup(up->pdev, true);
			up->wakeups_enabled = true;
		}
	} else {
		if (up->wakeups_enabled) {
			pdata->enable_wakeup(up->pdev, false);
			up->wakeups_enabled = false;
		}
	}

	/* Errata i291 */
	if (up->use_dma && pdata->set_forceidle &&
			(up->errata & UART_ERRATA_i291_DMA_FORCEIDLE))
		pdata->set_forceidle(up->pdev);

	up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
	schedule_work(&up->qos_work);

	return 0;
}

int cros_ec_suspend(struct cros_ec_device *ec_dev)
{
	struct device *dev = ec_dev->dev;
	int ret;
	u8 sleep_event;

	sleep_event = (!IS_ENABLED(CONFIG_ACPI) || pm_suspend_via_firmware()) ?
		      HOST_SLEEP_EVENT_S3_SUSPEND :
		      HOST_SLEEP_EVENT_S0IX_SUSPEND;

	ret = cros_ec_sleep_event(ec_dev, sleep_event);
	if (ret < 0)
		dev_dbg(ec_dev->dev, "Error %d sending suspend event to ec",
			ret);

	if (device_may_wakeup(dev))
		ec_dev->wake_enabled = !enable_irq_wake(ec_dev->irq);

	disable_irq(ec_dev->irq);
	ec_dev->was_wake_device = ec_dev->wake_enabled;
	ec_dev->suspended = true;

	return 0;
}

static ssize_t hall_wakeup_enable_store(struct device *dev,
						struct device_attribute *attr, const char *buf,
						size_t size)
{
	struct hall_sensor_data *hsdata = hsdev;
	int err = 0;
	int enable = 0;

	err = sscanf(buf, "%d", &enable);
	if (err < 0) {
		printk("[Hall] Set wakeup enable failed: %d\n", err);
		goto exit;
	}

	enable = !!enable;

	if (!device_may_wakeup(hsdata->dev))
		goto exit;

	if ((enable) && (!hsdata->wakeup_enable)) {
		enable_irq(hsdata->irq);
		enable_irq_wake(hsdata->irq);
	} else if (!(enable) && (hsdata->wakeup_enable)) {
		disable_irq_wake(hsdata->irq);
		disable_irq(hsdata->irq);
	}

	hsdata->wakeup_enable = enable;

#if defined(DEBUG)
	printk("[Hall] Set wakeup status : %d\n", (int)hsdata->wakeup_enable);
#endif

exit:
	return size;
}

static int __maybe_unused gsl_ts_resume(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct gsl_ts_data *ts = i2c_get_clientdata(client);

	dev_warn(&client->dev, "%s: resuming device\n", __func__);

	if (device_may_wakeup(dev) && ts->wake_irq_enabled) {
		disable_irq_wake(client->irq);
	}

	/* Do we need to do this ourselves? */
	acpi_bus_set_power(ACPI_HANDLE(&client->dev), ACPI_STATE_D0);
	usleep_range(20000, 50000);

	gsl_ts_reset_chip(client);
	gsl_ts_startup_chip(client);

	enable_irq(client->irq);

	ts->state = GSL_TS_GREEN;

	return 0;
}

static int davinci_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm)
{
	struct davinci_rtc *davinci_rtc = dev_get_drvdata(dev);
	u16 days = 0;
	u8 day0, day1;
	unsigned long flags;

	spin_lock_irqsave(&davinci_rtc_lock, flags);

	davinci_rtcss_calendar_wait(davinci_rtc);
	alm->time.tm_min = bcd2bin(rtcss_read(davinci_rtc, PRTCSS_RTC_AMIN));

	davinci_rtcss_calendar_wait(davinci_rtc);
	alm->time.tm_hour = bcd2bin(rtcss_read(davinci_rtc, PRTCSS_RTC_AHOUR));

	davinci_rtcss_calendar_wait(davinci_rtc);
	day0 = rtcss_read(davinci_rtc, PRTCSS_RTC_ADAY0);

	davinci_rtcss_calendar_wait(davinci_rtc);
	day1 = rtcss_read(davinci_rtc, PRTCSS_RTC_ADAY1);

	spin_unlock_irqrestore(&davinci_rtc_lock, flags);
	days |= day1;
	days <<= 8;
	days |= day0;

	if (convertfromdays(days, &alm->time) < 0)
		return -EINVAL;

	alm->pending = !!(rtcss_read(davinci_rtc,
			  PRTCSS_RTC_CCTRL) &
			PRTCSS_RTC_CCTRL_AIEN);
	alm->enabled = alm->pending && device_may_wakeup(dev);

	return 0;
}

static int msm_otg_suspend(struct msm_otg *motg)
{
	struct usb_phy *phy = &motg->phy;
	struct usb_bus *bus = phy->otg->host;
	struct msm_otg_platform_data *pdata = motg->pdata;
	void __iomem *addr;
	int cnt = 0;

	if (atomic_read(&motg->in_lpm))
		return 0;

	disable_irq(motg->irq);
	/*
	 * Chipidea 45-nm PHY suspend sequence:
	 *
	 * Interrupt Latch Register auto-clear feature is not present
	 * in all PHY versions. Latch register is clear on read type.
	 * Clear latch register to avoid spurious wakeup from
	 * low power mode (LPM).
	 *
	 * PHY comparators are disabled when PHY enters into low power
	 * mode (LPM). Keep PHY comparators ON in LPM only when we expect
	 * VBUS/Id notifications from USB PHY. Otherwise turn off USB
	 * PHY comparators. This save significant amount of power.
	 *
	 * PLL is not turned off when PHY enters into low power mode (LPM).
	 * Disable PLL for maximum power savings.
	 */

	if (motg->pdata->phy_type == CI_45NM_INTEGRATED_PHY) {
		ulpi_read(phy, 0x14);
		if (pdata->otg_control == OTG_PHY_CONTROL)
			ulpi_write(phy, 0x01, 0x30);
		ulpi_write(phy, 0x08, 0x09);
	}

	/*
	 * PHY may take some time or even fail to enter into low power
	 * mode (LPM). Hence poll for 500 msec and reset the PHY and link
	 * in failure case.
	 */
	writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
	while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
		if (readl(USB_PORTSC) & PORTSC_PHCD)
			break;
		udelay(1);
		cnt++;
	}

	if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) {
		dev_err(phy->dev, "Unable to suspend PHY\n");
		msm_otg_reset(phy);
		enable_irq(motg->irq);
		return -ETIMEDOUT;
	}

	/*
	 * PHY has capability to generate interrupt asynchronously in low
	 * power mode (LPM). This interrupt is level triggered. So USB IRQ
	 * line must be disabled till async interrupt enable bit is cleared
	 * in USBCMD register. Assert STP (ULPI interface STOP signal) to
	 * block data communication from PHY.
	 */
	writel(readl(USB_USBCMD) | ASYNC_INTR_CTRL | ULPI_STP_CTRL, USB_USBCMD);

	addr = USB_PHY_CTRL;
	if (motg->phy_number)
		addr = USB_PHY_CTRL2;

	if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
			motg->pdata->otg_control == OTG_PMIC_CONTROL)
		writel(readl(addr) | PHY_RETEN, addr);

	clk_disable_unprepare(motg->pclk);
	clk_disable_unprepare(motg->clk);
	if (!IS_ERR(motg->core_clk))
		clk_disable_unprepare(motg->core_clk);

	if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
			motg->pdata->otg_control == OTG_PMIC_CONTROL) {
		msm_hsusb_ldo_set_mode(motg, 0);
		msm_hsusb_config_vddcx(motg, 0);
	}

	if (device_may_wakeup(phy->dev))
		enable_irq_wake(motg->irq);
	if (bus)
		clear_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);

	atomic_set(&motg->in_lpm, 1);
	enable_irq(motg->irq);

	dev_info(phy->dev, "USB in low power mode\n");

	return 0;
}

//.........这里部分代码省略.........
	rc = sysfs_create_group(&kp->sec_keypad->kobj, &key_attr_group);
	if (rc) {
		dev_err(&pdev->dev, "Failed to create the test sysfs: %d\n",
			rc);
	}
#endif
	return 0;

err_pmic_reg_read:
	free_irq(kp->key_stuck_irq, kp);
err_req_stuck_irq:
	free_irq(kp->key_sense_irq, kp);
err_gpio_config:
err_get_irq:
	input_free_device(kp->input);
err_alloc_device:
	platform_set_drvdata(pdev, NULL);
	kfree(kp);
	return rc;
}

static int __devexit pmic8xxx_kp_remove(struct platform_device *pdev)
{
	struct pmic8xxx_kp *kp = platform_get_drvdata(pdev);

	device_init_wakeup(&pdev->dev, 0);
	free_irq(kp->key_stuck_irq, kp);
	free_irq(kp->key_sense_irq, kp);
	input_unregister_device(kp->input);
	kfree(kp);

	platform_set_drvdata(pdev, NULL);
	return 0;
}

#ifdef CONFIG_PM_SLEEP
static int pmic8xxx_kp_suspend(struct device *dev)
{
	struct platform_device *pdev = to_platform_device(dev);
	struct pmic8xxx_kp *kp = platform_get_drvdata(pdev);
	struct input_dev *input_dev = kp->input;

	if (device_may_wakeup(dev)) {
		enable_irq_wake(kp->key_sense_irq);
	} else {
		mutex_lock(&input_dev->mutex);

		if (input_dev->users)
			pmic8xxx_kp_disable(kp);

		mutex_unlock(&input_dev->mutex);
	}

	key_suspend = 1;

	return 0;
}

static int pmic8xxx_kp_resume(struct device *dev)
{
	struct platform_device *pdev = to_platform_device(dev);
	struct pmic8xxx_kp *kp = platform_get_drvdata(pdev);
	struct input_dev *input_dev = kp->input;

	if (device_may_wakeup(dev)) {
		disable_irq_wake(kp->key_sense_irq);
	} else {
		mutex_lock(&input_dev->mutex);

		if (input_dev->users)
			pmic8xxx_kp_enable(kp);

		mutex_unlock(&input_dev->mutex);
	}

	key_suspend = 0;

	return 0;
}
#endif

static SIMPLE_DEV_PM_OPS(pm8xxx_kp_pm_ops,
			 pmic8xxx_kp_suspend, pmic8xxx_kp_resume);

static struct platform_driver pmic8xxx_kp_driver = {
	.probe		= pmic8xxx_kp_probe,
	.remove		= __devexit_p(pmic8xxx_kp_remove),
	.driver		= {
		.name = PM8XXX_KEYPAD_DEV_NAME,
		.owner = THIS_MODULE,
		.pm = &pm8xxx_kp_pm_ops,
	},
};
module_platform_driver(pmic8xxx_kp_driver);

MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("PMIC8XXX keypad driver");
MODULE_VERSION("1.0");
MODULE_ALIAS("platform:pmic8xxx_keypad");
MODULE_AUTHOR("Trilok Soni <[email protected]>");

static int serial_omap_probe(struct platform_device *pdev)
{
	struct uart_omap_port	*up = NULL;
	struct resource		*mem, *irq, *dma_tx, *dma_rx;
	struct omap_uart_port_info *omap_up_info = pdev->dev.platform_data;
	struct omap_device *od;
	int ret = -ENOSPC;

	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!mem) {
		dev_err(&pdev->dev, "no mem resource?\n");
		return -ENODEV;
	}

	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
	if (!irq) {
		dev_err(&pdev->dev, "no irq resource?\n");
		return -ENODEV;
	}

	if (!request_mem_region(mem->start, (mem->end - mem->start) + 1,
				     pdev->dev.driver->name)) {
		dev_err(&pdev->dev, "memory region already claimed\n");
		return -EBUSY;
	}

	dma_rx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
	if (!dma_rx) {
		ret = -EINVAL;
		goto err;
	}

	dma_tx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
	if (!dma_tx) {
		ret = -EINVAL;
		goto err;
	}

	up = kzalloc(sizeof(*up), GFP_KERNEL);
	if (up == NULL) {
		ret = -ENOMEM;
		goto do_release_region;
	}
	sprintf(up->name, "OMAP UART%d", pdev->id);
	up->pdev = pdev;
	up->port.dev = &pdev->dev;
	up->port.type = PORT_OMAP;
	up->port.iotype = UPIO_MEM;
	up->port.irq = irq->start;

	up->port.regshift = 2;
	up->port.fifosize = 64;
	up->port.ops = &serial_omap_pops;
	up->port.line = pdev->id;

	up->port.mapbase = mem->start;
	up->port.membase = ioremap(mem->start, mem->end - mem->start);

	if (!up->port.membase) {
		dev_err(&pdev->dev, "can't ioremap UART\n");
		ret = -ENOMEM;
		goto err1;
	}

	up->port.flags = omap_up_info->flags;
	up->port.uartclk = omap_up_info->uartclk;
	up->uart_dma.uart_base = mem->start;
	up->errata = omap_up_info->errata;
	up->enable_wakeup = omap_up_info->enable_wakeup;
	up->wer = omap_up_info->wer;
	up->chk_wakeup = omap_up_info->chk_wakeup;
	up->wake_peer = omap_up_info->wake_peer;
	up->rts_mux_driver_control = omap_up_info->rts_mux_driver_control;
	up->rts_pullup_in_suspend = 0;
	up->wer_restore = 0;

	if (omap_up_info->use_dma) {
		up->uart_dma.uart_dma_tx = dma_tx->start;
		up->uart_dma.uart_dma_rx = dma_rx->start;
		up->use_dma = 1;
		up->uart_dma.rx_buf_size = omap_up_info->dma_rx_buf_size;
		up->uart_dma.rx_timeout = omap_up_info->dma_rx_timeout;
		up->uart_dma.rx_poll_rate = omap_up_info->dma_rx_poll_rate;
		spin_lock_init(&(up->uart_dma.tx_lock));
		spin_lock_init(&(up->uart_dma.rx_lock));
		up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
		up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
	}

	pm_runtime_use_autosuspend(&pdev->dev);
	pm_runtime_set_autosuspend_delay(&pdev->dev,
			omap_up_info->auto_sus_timeout);

	if (device_may_wakeup(&pdev->dev))
		pm_runtime_enable(&pdev->dev);

	pm_runtime_irq_safe(&pdev->dev);
	if (omap_up_info->console_uart) {
		od = to_omap_device(up->pdev);
		omap_hwmod_idle(od->hwmods[0]);
//.........这里部分代码省略.........

/**
 * acpi_dev_pm_get_state - Get preferred power state of ACPI device.
 * @dev: Device whose preferred target power state to return.
 * @adev: ACPI device node corresponding to @dev.
 * @target_state: System state to match the resultant device state.
 * @d_min_p: Location to store the highest power state available to the device.
 * @d_max_p: Location to store the lowest power state available to the device.
 *
 * Find the lowest power (highest number) and highest power (lowest number) ACPI
 * device power states that the device can be in while the system is in the
 * state represented by @target_state.  Store the integer numbers representing
 * those stats in the memory locations pointed to by @d_max_p and @d_min_p,
 * respectively.
 *
 * Callers must ensure that @dev and @adev are valid pointers and that @adev
 * actually corresponds to @dev before using this function.
 *
 * Returns 0 on success or -ENODATA when one of the ACPI methods fails or
 * returns a value that doesn't make sense.  The memory locations pointed to by
 * @d_max_p and @d_min_p are only modified on success.
 */
static int acpi_dev_pm_get_state(struct device *dev, struct acpi_device *adev,
				 u32 target_state, int *d_min_p, int *d_max_p)
{
	char method[] = { '_', 'S', '0' + target_state, 'D', '\0' };
	acpi_handle handle = adev->handle;
	unsigned long long ret;
	int d_min, d_max;
	bool wakeup = false;
	acpi_status status;

	/*
	 * If the system state is S0, the lowest power state the device can be
	 * in is D3cold, unless the device has _S0W and is supposed to signal
	 * wakeup, in which case the return value of _S0W has to be used as the
	 * lowest power state available to the device.
	 */
	d_min = ACPI_STATE_D0;
	d_max = ACPI_STATE_D3_COLD;

	/*
	 * If present, _SxD methods return the minimum D-state (highest power
	 * state) we can use for the corresponding S-states.  Otherwise, the
	 * minimum D-state is D0 (ACPI 3.x).
	 */
	if (target_state > ACPI_STATE_S0) {
		/*
		 * We rely on acpi_evaluate_integer() not clobbering the integer
		 * provided if AE_NOT_FOUND is returned.
		 */
		ret = d_min;
		status = acpi_evaluate_integer(handle, method, NULL, &ret);
		if ((ACPI_FAILURE(status) && status != AE_NOT_FOUND)
		    || ret > ACPI_STATE_D3_COLD)
			return -ENODATA;

		/*
		 * We need to handle legacy systems where D3hot and D3cold are
		 * the same and 3 is returned in both cases, so fall back to
		 * D3cold if D3hot is not a valid state.
		 */
		if (!adev->power.states[ret].flags.valid) {
			if (ret == ACPI_STATE_D3_HOT)
				ret = ACPI_STATE_D3_COLD;
			else
				return -ENODATA;
		}
		d_min = ret;
		wakeup = device_may_wakeup(dev) && adev->wakeup.flags.valid
			&& adev->wakeup.sleep_state >= target_state;
	} else if (dev_pm_qos_flags(dev, PM_QOS_FLAG_REMOTE_WAKEUP) !=
			PM_QOS_FLAGS_NONE) {
		wakeup = adev->wakeup.flags.valid;
	}

	/*
	 * If _PRW says we can wake up the system from the target sleep state,
	 * the D-state returned by _SxD is sufficient for that (we assume a
	 * wakeup-aware driver if wake is set).  Still, if _SxW exists
	 * (ACPI 3.x), it should return the maximum (lowest power) D-state that
	 * can wake the system.  _S0W may be valid, too.
	 */
	if (wakeup) {
		method[3] = 'W';
		status = acpi_evaluate_integer(handle, method, NULL, &ret);
		if (status == AE_NOT_FOUND) {
			if (target_state > ACPI_STATE_S0)
				d_max = d_min;
		} else if (ACPI_SUCCESS(status) && ret <= ACPI_STATE_D3_COLD) {
			/* Fall back to D3cold if ret is not a valid state. */
			if (!adev->power.states[ret].flags.valid)
				ret = ACPI_STATE_D3_COLD;

			d_max = ret > d_min ? ret : d_min;
		} else {
			return -ENODATA;
		}
	}

	if (d_min_p)
//.........这里部分代码省略.........

//.........这里部分代码省略.........
			if (temp & PORT_CONNECT) {
				status |= 1 << USB_PORT_FEAT_CONNECTION;
				// status may be from integrated TT
				status |= ehci_port_speed(ehci, temp);
			}
			if (temp & PORT_PE)
				status |= 1 << USB_PORT_FEAT_ENABLE;
			if (temp & (PORT_SUSPEND|PORT_RESUME))
				status |= 1 << USB_PORT_FEAT_SUSPEND;
			if (temp & PORT_OC)
				status |= 1 << USB_PORT_FEAT_OVER_CURRENT;
			if (temp & PORT_RESET)
				status |= 1 << USB_PORT_FEAT_RESET;
			if (temp & PORT_POWER)
				status |= 1 << USB_PORT_FEAT_POWER;
		}

#ifndef	EHCI_VERBOSE_DEBUG
	if (status & ~0xffff)	/* only if wPortChange is interesting */
#endif
		dbg_port (ehci, "GetStatus", wIndex + 1, temp);
		// we "know" this alignment is good, caller used kmalloc()...
		*((__le32 *) buf) = cpu_to_le32 (status);
		break;
	case SetHubFeature:
		switch (wValue) {
		case C_HUB_LOCAL_POWER:
		case C_HUB_OVER_CURRENT:
			/* no hub-wide feature/status flags */
			break;
		default:
			goto error;
		}
		break;
	case SetPortFeature:
		if (!wIndex || wIndex > ports)
			goto error;
		wIndex--;
		temp = readl (&ehci->regs->port_status [wIndex]);
		if (temp & PORT_OWNER)
			break;

		temp &= ~PORT_RWC_BITS;
		switch (wValue) {
		case USB_PORT_FEAT_SUSPEND:
			if ((temp & PORT_PE) == 0
					|| (temp & PORT_RESET) != 0)
				goto error;
			if (device_may_wakeup(&hcd->self.root_hub->dev))
				temp |= PORT_WAKE_BITS;
			writel (temp | PORT_SUSPEND,
				&ehci->regs->port_status [wIndex]);
			break;
		case USB_PORT_FEAT_POWER:
			if (HCS_PPC (ehci->hcs_params))
				writel (temp | PORT_POWER,
					&ehci->regs->port_status [wIndex]);
			break;
		case USB_PORT_FEAT_RESET:
			if (temp & PORT_RESUME)
				goto error;
			/* line status bits may report this as low speed,
			 * which can be fine if this root hub has a
			 * transaction translator built in.
			 */
			if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
					&& !ehci_is_TDI(ehci)
					&& PORT_USB11 (temp)) {
				ehci_dbg (ehci,
					"port %d low speed --> companion\n",
					wIndex + 1);
				temp |= PORT_OWNER;
			} else {
				ehci_vdbg (ehci, "port %d reset\n", wIndex + 1);
				temp |= PORT_RESET;
				temp &= ~PORT_PE;

				/*
				 * caller must wait, then call GetPortStatus
				 * usb 2.0 spec says 50 ms resets on root
				 */
				ehci->reset_done [wIndex] = jiffies
						+ msecs_to_jiffies (50);
			}
			writel (temp, &ehci->regs->port_status [wIndex]);
			break;
		default:
			goto error;
		}
		readl (&ehci->regs->command);	/* unblock posted writes */
		break;

	default:
error:
		/* "stall" on error */
		retval = -EPIPE;
	}
	spin_unlock_irqrestore (&ehci->lock, flags);
	return retval;
}

static struct adapter *rtw_usb_if1_init(struct dvobj_priv *dvobj,
                                        struct usb_interface *pusb_intf, const struct usb_device_id *pdid)
{
    struct adapter *padapter = NULL;
    struct net_device *pnetdev = NULL;
    int status = _FAIL;

    padapter = (struct adapter *)vzalloc(sizeof(*padapter));
    if (padapter == NULL)
        goto exit;
    padapter->dvobj = dvobj;
    dvobj->if1 = padapter;

    padapter->bDriverStopped = true;
    mutex_init(&padapter->hw_init_mutex);
    padapter->chip_type = RTL8188E;

    pnetdev = rtw_init_netdev(padapter);
    if (pnetdev == NULL)
        goto free_adapter;
    SET_NETDEV_DEV(pnetdev, dvobj_to_dev(dvobj));
    padapter = rtw_netdev_priv(pnetdev);

    /* step 2. hook HalFunc, allocate HalData */
    hal_set_hal_ops(padapter);

    padapter->intf_start = &usb_intf_start;
    padapter->intf_stop = &usb_intf_stop;

    /* step read_chip_version */
    rtw_hal_read_chip_version(padapter);

    /* step usb endpoint mapping */
    rtw_hal_chip_configure(padapter);

    /* step read efuse/eeprom data and get mac_addr */
    rtw_hal_read_chip_info(padapter);

    /* step 5. */
    if (rtw_init_drv_sw(padapter) == _FAIL) {
        RT_TRACE(_module_hci_intfs_c_, _drv_err_,
                 ("Initialize driver software resource Failed!\n"));
        goto free_hal_data;
    }

#ifdef CONFIG_PM
    if (padapter->pwrctrlpriv.bSupportRemoteWakeup) {
        dvobj->pusbdev->do_remote_wakeup = 1;
        pusb_intf->needs_remote_wakeup = 1;
        device_init_wakeup(&pusb_intf->dev, 1);
        DBG_88E("\n  padapter->pwrctrlpriv.bSupportRemoteWakeup~~~~~~\n");
        DBG_88E("\n  padapter->pwrctrlpriv.bSupportRemoteWakeup~~~[%d]~~~\n",
                device_may_wakeup(&pusb_intf->dev));
    }
#endif

    /* 2012-07-11 Move here to prevent the 8723AS-VAU BT auto
     * suspend influence */
    if (usb_autopm_get_interface(pusb_intf) < 0)
        DBG_88E("can't get autopm:\n");

    /*  alloc dev name after read efuse. */
    rtw_init_netdev_name(pnetdev, padapter->registrypriv.ifname);
    rtw_macaddr_cfg(padapter->eeprompriv.mac_addr);
    memcpy(pnetdev->dev_addr, padapter->eeprompriv.mac_addr, ETH_ALEN);
    DBG_88E("MAC Address from pnetdev->dev_addr =  %pM\n",
            pnetdev->dev_addr);

    /* step 6. Tell the network stack we exist */
    if (register_netdev(pnetdev) != 0) {
        RT_TRACE(_module_hci_intfs_c_, _drv_err_, ("register_netdev() failed\n"));
        goto free_hal_data;
    }

    DBG_88E("bDriverStopped:%d, bSurpriseRemoved:%d, bup:%d, hw_init_completed:%d\n"
            , padapter->bDriverStopped
            , padapter->bSurpriseRemoved
            , padapter->bup
            , padapter->hw_init_completed
           );

    status = _SUCCESS;

free_hal_data:
    if (status != _SUCCESS)
        kfree(padapter->HalData);
free_adapter:
    if (status != _SUCCESS) {
        if (pnetdev)
            rtw_free_netdev(pnetdev);
        else if (padapter)
            vfree(padapter);
        padapter = NULL;
    }
exit:
    return padapter;
}

//.........这里部分代码省略.........
	if (IS_ERR(priv->rtc))
		return PTR_ERR(priv->rtc);

	priv->rtc->nvram_old_abi = true;
	priv->rtc->ops = &ds1343_rtc_ops;

	res = rtc_register_device(priv->rtc);
	if (res)
		return res;

	nvmem_cfg.priv = priv;
	rtc_nvmem_register(priv->rtc, &nvmem_cfg);

	priv->irq = spi->irq;

	if (priv->irq >= 0) {
		res = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
						ds1343_thread, IRQF_ONESHOT,
						"ds1343", priv);
		if (res) {
			priv->irq = -1;
			dev_err(&spi->dev,
				"unable to request irq for rtc ds1343\n");
		} else {
			device_init_wakeup(&spi->dev, true);
			dev_pm_set_wake_irq(&spi->dev, spi->irq);
		}
	}

	res = ds1343_sysfs_register(&spi->dev);
	if (res)
		dev_err(&spi->dev,
			"unable to create sysfs entries for rtc ds1343\n");

	return 0;
}

static int ds1343_remove(struct spi_device *spi)
{
	struct ds1343_priv *priv = spi_get_drvdata(spi);

	if (spi->irq) {
		mutex_lock(&priv->mutex);
		priv->irqen &= ~RTC_AF;
		mutex_unlock(&priv->mutex);

		dev_pm_clear_wake_irq(&spi->dev);
		device_init_wakeup(&spi->dev, false);
		devm_free_irq(&spi->dev, spi->irq, priv);
	}

	spi_set_drvdata(spi, NULL);

	ds1343_sysfs_unregister(&spi->dev);

	return 0;
}

#ifdef CONFIG_PM_SLEEP

static int ds1343_suspend(struct device *dev)
{
	struct spi_device *spi = to_spi_device(dev);

	if (spi->irq >= 0 && device_may_wakeup(dev))
		enable_irq_wake(spi->irq);

	return 0;
}

static int ds1343_resume(struct device *dev)
{
	struct spi_device *spi = to_spi_device(dev);

	if (spi->irq >= 0 && device_may_wakeup(dev))
		disable_irq_wake(spi->irq);

	return 0;
}

#endif

static SIMPLE_DEV_PM_OPS(ds1343_pm, ds1343_suspend, ds1343_resume);

static struct spi_driver ds1343_driver = {
	.driver = {
		.name = "ds1343",
		.pm = &ds1343_pm,
	},
	.probe = ds1343_probe,
	.remove = ds1343_remove,
	.id_table = ds1343_id,
};

module_spi_driver(ds1343_driver);

MODULE_DESCRIPTION("DS1343 RTC SPI Driver");
MODULE_AUTHOR("Raghavendra Chandra Ganiga <[email protected]>,"
		"Ankur Srivastava <[email protected]>");
MODULE_LICENSE("GPL v2");

/*
 * drv_init() - a device potentially for us
 *
 * notes: drv_init() is called when the bus driver has located a card
 * for us to support.
 *        We accept the new device by returning 0.
 */
static struct rtw_adapter *rtw_usb_if1_init(struct dvobj_priv *dvobj,
					    struct usb_interface *pusb_intf,
					    const struct usb_device_id *pdid)
{
	struct rtw_adapter *padapter = NULL;
	struct net_device *pnetdev = NULL;
	int status = _FAIL;

	pnetdev = rtw_init_netdev23a(padapter);
	if (!pnetdev)
		goto free_adapter;
	padapter = netdev_priv(pnetdev);

	padapter->dvobj = dvobj;
	padapter->bDriverStopped = true;
	dvobj->if1 = padapter;
	dvobj->padapters[dvobj->iface_nums++] = padapter;
	padapter->iface_id = IFACE_ID0;

	rtl8723au_set_hw_type(padapter);

	SET_NETDEV_DEV(pnetdev, dvobj_to_dev(dvobj));

	if (rtw_wdev_alloc(padapter, dvobj_to_dev(dvobj)))
		goto free_adapter;

	/* step 2. allocate HalData */
	padapter->HalData = kzalloc(sizeof(struct hal_data_8723a), GFP_KERNEL);
	if (!padapter->HalData)
		goto free_wdev;

	/* step read_chip_version */
	rtl8723a_read_chip_version(padapter);

	/* step usb endpoint mapping */
	if (!rtl8723au_chip_configure(padapter))
		goto free_hal_data;

	/* step read efuse/eeprom data and get mac_addr */
	rtl8723a_read_adapter_info(padapter);

	/* step 5. */
	if (rtw_init_drv_sw23a(padapter) == _FAIL) {
		RT_TRACE(_module_hci_intfs_c_, _drv_err_,
			 ("Initialize driver software resource Failed!\n"));
		goto free_hal_data;
	}

#ifdef CONFIG_PM
	if (padapter->pwrctrlpriv.bSupportRemoteWakeup) {
		dvobj->pusbdev->do_remote_wakeup = 1;
		pusb_intf->needs_remote_wakeup = 1;
		device_init_wakeup(&pusb_intf->dev, 1);
		DBG_8723A("\n  padapter->pwrctrlpriv.bSupportRemoteWakeup~~~~~~\n");
		DBG_8723A("\n  padapter->pwrctrlpriv.bSupportRemoteWakeup~~~[%d]~~~\n",
			  device_may_wakeup(&pusb_intf->dev));
	}
#endif
	/* 2012-07-11 Move here to prevent the 8723AS-VAU BT
	 * auto suspend influence
	 */
	if (usb_autopm_get_interface(pusb_intf) < 0)
		DBG_8723A("can't get autopm:\n");
#ifdef	CONFIG_8723AU_BT_COEXIST
	padapter->pwrctrlpriv.autopm_cnt = 1;
#endif

	/* If the eeprom mac address is corrupted, assign a random address */
	if (is_broadcast_ether_addr(padapter->eeprompriv.mac_addr) ||
	    is_zero_ether_addr(padapter->eeprompriv.mac_addr))
		eth_random_addr(padapter->eeprompriv.mac_addr);

	DBG_8723A("bDriverStopped:%d, bSurpriseRemoved:%d, bup:%d, hw_init_completed:%d\n",
		  padapter->bDriverStopped, padapter->bSurpriseRemoved,
		  padapter->bup, padapter->hw_init_completed
	);
	status = _SUCCESS;

free_hal_data:
	if (status != _SUCCESS)
		kfree(padapter->HalData);
free_wdev:
	if (status != _SUCCESS) {
		rtw_wdev_unregister(padapter->rtw_wdev);
		rtw_wdev_free(padapter->rtw_wdev);
	}
free_adapter:
	if (status != _SUCCESS) {
		if (pnetdev)
			free_netdev(pnetdev);
		padapter = NULL;
	}
	return padapter;
//.........这里部分代码省略.........

static int __devinit
ohci_pci_start (struct usb_hcd *hcd)
{
	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
	int		ret;

	/* REVISIT this whole block should move to reset(), which handles
	 * all the other one-time init.
	 */
	if (hcd->self.controller) {
		struct pci_dev *pdev = to_pci_dev(hcd->self.controller);

		/* AMD 756, for most chips (early revs), corrupts register
		 * values on read ... so enable the vendor workaround.
		 */
		if (pdev->vendor == PCI_VENDOR_ID_AMD
				&& pdev->device == 0x740c) {
			ohci->flags = OHCI_QUIRK_AMD756;
			ohci_dbg (ohci, "AMD756 erratum 4 workaround\n");
			/* also erratum 10 (suspend/resume issues) */
			device_init_wakeup(&hcd->self.root_hub->dev, 0);
		}

		/* FIXME for some of the early AMD 760 southbridges, OHCI
		 * won't work at all.  blacklist them.
		 */

		/* Apple's OHCI driver has a lot of bizarre workarounds
		 * for this chip.  Evidently control and bulk lists
		 * can get confused.  (B&W G3 models, and ...)
		 */
		else if (pdev->vendor == PCI_VENDOR_ID_OPTI
				&& pdev->device == 0xc861) {
			ohci_dbg (ohci,
				"WARNING: OPTi workarounds unavailable\n");
		}

		/* Check for NSC87560. We have to look at the bridge (fn1) to
		 * identify the USB (fn2). This quirk might apply to more or
		 * even all NSC stuff.
		 */
		else if (pdev->vendor == PCI_VENDOR_ID_NS) {
			struct pci_dev	*b;

			b  = pci_get_slot (pdev->bus,
					PCI_DEVFN (PCI_SLOT (pdev->devfn), 1));
			if (b && b->device == PCI_DEVICE_ID_NS_87560_LIO
					&& b->vendor == PCI_VENDOR_ID_NS) {
				ohci->flags |= OHCI_QUIRK_SUPERIO;
				ohci_dbg (ohci, "Using NSC SuperIO setup\n");
			}
			pci_dev_put(b);
		}

		/* Check for Compaq's ZFMicro chipset, which needs short
		 * delays before control or bulk queues get re-activated
		 * in finish_unlinks()
		 */
		else if (pdev->vendor == PCI_VENDOR_ID_COMPAQ
				&& pdev->device  == 0xa0f8) {
			ohci->flags |= OHCI_QUIRK_ZFMICRO;
			ohci_dbg (ohci,
				"enabled Compaq ZFMicro chipset quirk\n");
		}

		/* RWC may not be set for add-in PCI cards, since boot
		 * firmware probably ignored them.  This transfers PCI
		 * PM wakeup capabilities (once the PCI layer is fixed).
		 */
		if (device_may_wakeup(&pdev->dev))
			ohci->hc_control |= OHCI_CTRL_RWC;
	}

	/* NOTE: there may have already been a first reset, to
	 * keep bios/smm irqs from making trouble
	 */
	if ((ret = ohci_run (ohci)) < 0) {
		ohci_err (ohci, "can't start\n");
		ohci_stop (hcd);
		return ret;
	}
	return 0;
}

static bool tegra_pd_active_wakeup(struct device *dev)
{
	return device_may_wakeup(dev);
}

static void
wbcir_shutdown(struct pnp_dev *device)
{
	struct device *dev = &device->dev;
	struct wbcir_data *data = pnp_get_drvdata(device);
	bool do_wake = true;
	u8 match[11];
	u8 mask[11];
	u8 rc6_csl = 0;
	int i;

	memset(match, 0, sizeof(match));
	memset(mask, 0, sizeof(mask));

	if (wake_sc == INVALID_SCANCODE || !device_may_wakeup(dev)) {
		do_wake = false;
		goto finish;
	}

	switch (protocol) {
	case IR_PROTOCOL_RC5:
		if (wake_sc > 0xFFF) {
			do_wake = false;
			dev_err(dev, "RC5 - Invalid wake scancode\n");
			break;
		}

		/* Mask = 13 bits, ex toggle */
		mask[0] = 0xFF;
		mask[1] = 0x17;

		match[0]  = (wake_sc & 0x003F);      /* 6 command bits */
		match[0] |= (wake_sc & 0x0180) >> 1; /* 2 address bits */
		match[1]  = (wake_sc & 0x0E00) >> 9; /* 3 address bits */
		if (!(wake_sc & 0x0040))             /* 2nd start bit  */
			match[1] |= 0x10;

		break;

	case IR_PROTOCOL_NEC:
		if (wake_sc > 0xFFFFFF) {
			do_wake = false;
			dev_err(dev, "NEC - Invalid wake scancode\n");
			break;
		}

		mask[0] = mask[1] = mask[2] = mask[3] = 0xFF;

		match[1] = bitrev8((wake_sc & 0xFF));
		match[0] = ~match[1];

		match[3] = bitrev8((wake_sc & 0xFF00) >> 8);
		if (wake_sc > 0xFFFF)
			match[2] = bitrev8((wake_sc & 0xFF0000) >> 16);
		else
			match[2] = ~match[3];

		break;

	case IR_PROTOCOL_RC6:

		if (wake_rc6mode == 0) {
			if (wake_sc > 0xFFFF) {
				do_wake = false;
				dev_err(dev, "RC6 - Invalid wake scancode\n");
				break;
			}

			/* Command */
			match[0] = wbcir_to_rc6cells(wake_sc >>  0);
			mask[0]  = 0xFF;
			match[1] = wbcir_to_rc6cells(wake_sc >>  4);
			mask[1]  = 0xFF;

			/* Address */
			match[2] = wbcir_to_rc6cells(wake_sc >>  8);
			mask[2]  = 0xFF;
			match[3] = wbcir_to_rc6cells(wake_sc >> 12);
			mask[3]  = 0xFF;

			/* Header */
			match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */
			mask[4]  = 0xF0;
			match[5] = 0x09; /* start bit = 1, mode2 = 0 */
			mask[5]  = 0x0F;

			rc6_csl = 44;

		} else if (wake_rc6mode == 6) {