C++ dev_add_bb_dev函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中dev_add_bb_dev函数的典型用法代码示例。如果您正苦于以下问题：C++ dev_add_bb_dev函数的具体用法？C++ dev_add_bb_dev怎么用？C++ dev_add_bb_dev使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了dev_add_bb_dev函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: cupid_devices_init

static int cupid_devices_init(void)
{
	uint32_t reg;

	gpio_direction_output(GPIO_LCD_ENABLE, 0);
	gpio_direction_output(GPIO_LCD_BACKLIGHT, 0);

	reg = readl(IMX_CCM_BASE + CCM_RCSR);
	/* some fuses provide us vital information about connected hardware */
	if (reg & 0x20000000)
		nand_info.width = 2;    /* 16 bit */
	else
		nand_info.width = 1;    /* 8 bit */

	imx35_add_fec(&fec_info);
	imx35_add_nand(&nand_info);

	devfs_add_partition("nand0", 0x00000, 0x40000, PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x40000, 0x80000, PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	imx35_add_fb(&ipu_fb_data);
	imx35_add_mmc0(NULL);

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_GUF_CUPID);

	return 0;
}

开发者ID:prpplague，项目名称:das_oszi_barebox，代码行数:30，代码来源:board.c

示例2: pcm049_devices_init

static int pcm049_devices_init(void)
{
	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
	add_generic_device("i2c-omap", -1, NULL, 0x48070000, 0x1000,
				IORESOURCE_MEM, NULL);

	add_generic_device("omap-hsmmc", -1, NULL, 0x4809C100, SZ_4K,
			   IORESOURCE_MEM, NULL);

	gpmc_generic_init(0x10);

	pcm049_network_init();

	gpmc_generic_nand_devices_init(0, 8, OMAP_ECC_BCH8_CODE_HW);

#ifdef CONFIG_PARTITION
	devfs_add_partition("nand0", 0x00000, SZ_128K, PARTITION_FIXED, "xload_raw");
	dev_add_bb_dev("xload_raw", "xload");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_128K + SZ_256K, SZ_128K, PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
#endif

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_PCM049);

	return 0;
}

开发者ID:cpdesign，项目名称:barebox，代码行数:29，代码来源:board.c

示例3: nhk8815_devices_init

static int nhk8815_devices_init(void)
{
	writel(0xC37800F0, NOMADIK_GPIO1_BASE + 0x20);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x24);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
	writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);

	/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
	writel(0x0000305b, FSMC_BCR(1));
	writel(0x00033f33, FSMC_BTR(1));

	add_generic_device("smc91c111", DEVICE_ID_DYNAMIC, NULL, 0x34000300, 16,
			   IORESOURCE_MEM, NULL);

	platform_device_register(&nhk8815_nand_device);

	armlinux_set_architecture(MACH_TYPE_NOMADIK);
	armlinux_set_bootparams((void *)(0x00000100));

	devfs_add_partition("nand0", 0x0000000, 0x040000, DEVFS_PARTITION_FIXED, "xloader_raw");
	devfs_add_partition("nand0", 0x0040000, 0x080000, DEVFS_PARTITION_FIXED, "meminit_raw");
	devfs_add_partition("nand0", 0x0080000, 0x200000, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x7FE0000, 0x020000, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	return 0;
}

开发者ID:Jokymon，项目名称:barebox，代码行数:28，代码来源:setup.c

示例4: at91sam9n12ek_devices_init

static int at91sam9n12ek_devices_init(void)
{
	ek_add_device_spi();
	ek_add_device_nand();
	ek_add_device_mci();
	ek_add_led();
	at91_add_device_udc(&ek_udc_data);
	ek_add_device_i2c();
	ek_add_device_ks8851();
	ek_add_device_buttons();
	ek_add_device_lcdc();

	armlinux_set_architecture(CONFIG_MACH_AT91SAM9N12EK);

	devfs_add_partition("nand0", 0x00000, SZ_256K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_256K, SZ_256K + SZ_128K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_512K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K + SZ_256K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	return 0;
}

开发者ID:cuijfboy，项目名称:barebox，代码行数:25，代码来源:init.c

示例5: tx25_devices_init

static int tx25_devices_init(void)
{
	gpio_fec_active();

	imx25_iim_register_fec_ethaddr();
	imx25_add_fec(&fec_info);

	if (readl(MX25_CCM_BASE_ADDR + MX25_CCM_RCSR) & (1 << 14))
		nand_info.width = 2;

	imx25_add_nand(&nand_info);

	devfs_add_partition("nand0", 0x00000, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");

	devfs_add_partition("nand0", SZ_512K, SZ_512K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	add_mem_device("sram0", 0x78000000, 128 * 1024,
				   IORESOURCE_MEM_WRITEABLE);

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_TX25);
	armlinux_set_serial(imx_uid());

	return 0;
}

开发者ID:AshishNamdev，项目名称:barebox，代码行数:27，代码来源:board.c

示例6: pcm049_devices_init

static int pcm049_devices_init(void)
{
	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
	omap44xx_add_i2c1(NULL);
	omap44xx_add_mmc1(NULL);

	gpmc_generic_init(0x10);

	pcm049_network_init();

	omap_add_gpmc_nand_device(&nand_plat);

#ifdef CONFIG_PARTITION
	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "xload_raw");
	dev_add_bb_dev("xload_raw", "xload");
	devfs_add_partition("nand0", SZ_128K, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_128K + SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
#endif

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_PCM049);

	return 0;
}

开发者ID:SayCV，项目名称:barebox-at91，代码行数:26，代码来源:board.c

示例7: usb_a9260_devices_init

static int usb_a9260_devices_init(void)
{
	usb_a9260_add_device_nand();
	usb_a9260_add_device_mci();
	usb_a9260_add_device_eth();
	usb_a9260_add_spi();
	usb_a9260_add_device_usb();
	ek_add_device_udc();
	ek_add_led();
	ek_add_device_button();
	usb_a9260_device_dab_mmx();

	usb_a9260_set_board_type();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	return 0;
}

开发者ID:cherojeong，项目名称:barebox，代码行数:25，代码来源:init.c

示例8: at91sam9x5ek_devices_init

static int at91sam9x5ek_devices_init(void)
{
	ek_add_device_w1();
	ek_add_device_nand();
	ek_add_device_eth();
	ek_add_device_spi();
	ek_add_device_mci();
	ek_add_device_usb();
	ek_add_led();
	ek_add_device_i2c();
	ek_add_device_lcdc();

	armlinux_set_architecture(CONFIG_MACH_AT91SAM9X5EK);

	devfs_add_partition("nand0", 0x00000, SZ_256K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_256K, SZ_256K + SZ_128K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_512K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K + SZ_256K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	if (IS_ENABLED(CONFIG_DEFAULT_ENVIRONMENT_GENERIC))
		defaultenv_append_directory(defaultenv_at91sam9x5ek);

	return 0;
}

开发者ID:Tractorfirmware，项目名称:barebox，代码行数:28，代码来源:init.c

示例9: at91sam9261ek_devices_init

static int at91sam9261ek_devices_init(void)
{

	ek_add_device_nand();
	ek_add_device_dm9000();
	ek_add_device_udc();
	ek_add_device_buttons();
	ek_device_add_leds();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
	if (machine_is_at91sam9g10ek())
		armlinux_set_architecture(MACH_TYPE_AT91SAM9G10EK);
	else
		armlinux_set_architecture(MACH_TYPE_AT91SAM9261EK);

	return 0;
}

开发者ID:cyox93，项目名称:barebox，代码行数:25，代码来源:init.c

示例10: imx25_3ds_devices_init

static int imx25_3ds_devices_init(void)
{
#ifdef CONFIG_USB
	/* USB does not work yet. Don't know why. Maybe
	 * the CPLD has to be initialized.
	 */
	imx25_usb_init();
	add_generic_usb_ehci_device(DEVICE_ID_DYNAMIC, MX25_USB_OTG_BASE_ADDR + 0x400, NULL);
#endif

	imx25_iim_register_fec_ethaddr();
	imx25_add_fec(&fec_info);

	add_mem_device("sram0", 0x78000000, 128 * 1024, IORESOURCE_MEM_WRITEABLE);

	if (readl(MX25_CCM_BASE_ADDR + MX25_CCM_RCSR) & (1 << 14))
		nand_info.width = 2;

	imx25_add_nand(&nand_info);

	devfs_add_partition("nand0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");

	devfs_add_partition("nand0", 0x40000, 0x20000, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
	imx25_add_i2c0(NULL);

	armlinux_set_architecture(MACH_TYPE_MX25_3DS);
	armlinux_set_serial(imx_uid());

	return 0;
}

开发者ID:AubrCool，项目名称:barebox，代码行数:34，代码来源:3stack.c

示例11: at91sam9m10g45ek_devices_init

static int at91sam9m10g45ek_devices_init(void)
{
	ek_add_device_nand();
	ek_add_device_spi();
	at91_add_device_eth(0, &macb_pdata);
	ek_add_device_mci();
	ek_add_device_usb();
	ek_device_add_leds();
	ek_device_add_keyboard();
	ek_add_device_lcdc();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_6 + 0x100));
	armlinux_set_architecture(MACH_TYPE_AT91SAM9M10G45EK);
	ek_set_board_revision();

	return 0;
}

开发者ID:SayCV，项目名称:barebox-at91，代码行数:26，代码来源:init.c

示例12: vincell_devices_init

static int vincell_devices_init(void)
{
	writel(0, MX53_M4IF_BASE_ADDR + 0xc);

	console_flush();
	imx53_init_lowlevel(1000);
	clk_set_rate(clk_lookup("nfc_podf"), 66666667);

	imx53_add_nand(&nand_info);
	imx51_iim_register_fec_ethaddr();
	imx53_add_fec(&fec_info);
	imx53_add_mmc0(NULL);
	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
	imx53_add_i2c0(NULL);

	vincell_fec_reset();

	armlinux_set_bootparams((void *)0x70000100);
	armlinux_set_architecture(3297);

	devfs_add_partition("nand0", SZ_1M, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_1M + SZ_512K, SZ_512K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	imx53_bbu_internal_nand_register_handler("nand",
		BBU_HANDLER_FLAG_DEFAULT, dcd_entry, sizeof(dcd_entry), 3 * SZ_128K, 0xf8020000);

	return 0;
}

开发者ID:Reggi3，项目名称:mini210s-barebox，代码行数:30，代码来源:board.c

示例13: at91sam9m10ihd_devices_init

static int at91sam9m10ihd_devices_init(void)
{
	ek_add_device_w1();
	ek_add_device_nand();
	ek_add_device_eth();
	ek_add_device_mci();
	ek_add_device_spi();
	ek_add_device_i2c();
	ek_add_device_usb();
	ek_add_device_lcd();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	/*
	 * The internal Atmel kernel use the SAM9M10G45EK machine id
	 * The mainline use DT
	 */
	armlinux_set_architecture(MACH_TYPE_AT91SAM9M10G45EK);

	return 0;
}

开发者ID:AubrCool，项目名称:barebox，代码行数:28，代码来源:init.c

示例14: nhk8815_devices_init

static int nhk8815_devices_init(void)
{
	st8815_add_device_sdram(64 * 1024 *1024);

	writel(0xC37800F0, NOMADIK_GPIO1_BASE + 0x20);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x24);
	writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
	writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);

	/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
	writel(0x0000305b, FSMC_BCR(1));
	writel(0x00033f33, FSMC_BTR(1));

	register_device(&nhk8815_network_dev);

	register_device(&nhk8815_nand_device);

	armlinux_set_architecture(MACH_TYPE_NOMADIK);
	armlinux_set_bootparams((void *)(0x00000100));

	devfs_add_partition("nand0", 0x0000000, 0x040000, PARTITION_FIXED, "xloader_raw");
	devfs_add_partition("nand0", 0x0040000, 0x080000, PARTITION_FIXED, "meminit_raw");
	devfs_add_partition("nand0", 0x0080000, 0x200000, PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x7FE0000, 0x020000, PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	return 0;
}

开发者ID:ray650128，项目名称:barebox-sh4-nextvod，代码行数:29，代码来源:setup.c

示例15: eukrea_cpuimx25_devices_init

static int eukrea_cpuimx25_devices_init(void)
{
	eukrea_cpuimx25_mmu_init();

	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx25_pads,
		ARRAY_SIZE(eukrea_cpuimx25_pads));
	register_device(&fec_dev);

	nand_info.width = 1;
	register_device(&nand_dev);

	devfs_add_partition("nand0", 0x00000, 0x40000,
		PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");

	devfs_add_partition("nand0", 0x40000, 0x20000,
		PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	register_device(&sdram0_dev);

	/* enable LCD */
	gpio_direction_output(26, 1);
	gpio_set_value(26, 1);

	register_device(&imxfb_dev);

	armlinux_add_dram(&sdram0_dev);
	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_EUKREA_CPUIMX25);

	return 0;
}

开发者ID:ray650128，项目名称:barebox-sh4-nextvod，代码行数:33，代码来源:eukrea_cpuimx25.c

示例16: at91sam9260ek_devices_init

static int at91sam9260ek_devices_init(void)
{
	ek_add_device_nand();
	at91sam9260ek_phy_reset();
	at91_add_device_eth(0, &macb_pdata);
	at91_add_device_usbh_ohci(&ek_usbh_data);
	at91_add_device_udc(&ek_udc_data);
	ek_usb_add_device_mci();
	ek_add_device_buttons();
	ek_add_led();

	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
	ek_set_board_type();

	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
	dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
	devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
	devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
	dev_add_bb_dev("env_raw1", "env1");

	return 0;
}

开发者ID:RobertCNelson，项目名称:barebox-boards，代码行数:25，代码来源:init.c

示例17: pcm049_devices_init

static int pcm049_devices_init(void)
{
	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
	omap44xx_add_i2c1(NULL);
	omap44xx_add_mmc1(NULL);

	gpmc_generic_init(0x10);

	if (IS_ENABLED(CONFIG_DRIVER_NET_SMC911X))
		pcm049_network_init();

	omap_add_gpmc_nand_device(&nand_plat);

#ifdef CONFIG_PARTITION
	devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "xload_raw");
	dev_add_bb_dev("xload_raw", "xload");
	devfs_add_partition("nand0", SZ_128K, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", SZ_128K + SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");
#endif

	armlinux_set_architecture(MACH_TYPE_PCM049);

	if (IS_ENABLED(CONFIG_DRIVER_VIDEO_OMAP))
		omap_add_display(&pcm049_fb_data);

	return 0;
}

开发者ID:RobertCNelson，项目名称:barebox，代码行数:29，代码来源:board.c

示例18: pcm043_devices_init

static int pcm043_devices_init(void)
{
	uint32_t reg;
	char *envstr;
	unsigned long bbu_nand_flags = 0;

	/* CS0: Nor Flash */
	imx35_setup_weimcs(5, 0x22C0CF00, 0x75000D01, 0x00000900);

	led_gpio_register(&led0);

	reg = readl(MX35_CCM_BASE_ADDR + MX35_CCM_RCSR);
	/* some fuses provide us vital information about connected hardware */
	if (reg & 0x20000000)
		nand_info.width = 2;    /* 16 bit */
	else
		nand_info.width = 1;    /* 8 bit */

	imx35_add_fec(&fec_info);
	/*
	 * This platform supports NOR and NAND
	 */
	imx35_add_nand(&nand_info);
	/*
	 * Up to 32MiB NOR type flash, connected to
	 * CS line 0, data width is 16 bit
	 */
	add_cfi_flash_device(DEVICE_ID_DYNAMIC, MX35_CS0_BASE_ADDR, 32 * 1024 * 1024, 0);

	switch (bootsource_get()) {
	case BOOTSOURCE_NAND:
		devfs_add_partition("nand0", 0x00000, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
		dev_add_bb_dev("self_raw", "self0");
		devfs_add_partition("nand0", SZ_512K, SZ_256K, DEVFS_PARTITION_FIXED, "env_raw");
		dev_add_bb_dev("env_raw", "env0");
		envstr = "NAND";
		bbu_nand_flags = BBU_HANDLER_FLAG_DEFAULT;
		break;
	case BOOTSOURCE_NOR:
	default:
		devfs_add_partition("nor0", 0x00000, SZ_512K, DEVFS_PARTITION_FIXED, "self0"); /* ourself */
		devfs_add_partition("nor0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env0");  /* environment */
		protect_file("/dev/env0", 1);
		envstr = "NOR";
		break;
	}

	pr_info("using environment from %s flash\n", envstr);

	imx35_add_fb(&ipu_fb_data);

	armlinux_set_architecture(MACH_TYPE_PCM043);

	imx_bbu_external_nand_register_handler("nand", "/dev/nand0.barebox",
			bbu_nand_flags);

	return 0;
}

开发者ID:AubrCool，项目名称:barebox，代码行数:58，代码来源:pcm043.c

示例19: tx51_part_init

static int tx51_part_init(void)
{
	devfs_add_partition("nand0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self_raw");
	dev_add_bb_dev("self_raw", "self0");
	devfs_add_partition("nand0", 0x40000, 0x80000, DEVFS_PARTITION_FIXED, "env_raw");
	dev_add_bb_dev("env_raw", "env0");

	return 0;
}

开发者ID:MinimumLaw，项目名称:ravion-barebox，代码行数:9，代码来源:tx51.c

示例20: f3s_devices_init

static int f3s_devices_init(void)
{
	uint32_t reg;

	/* CS0: Nor Flash */
	imx35_setup_weimcs(0, 0x0000cf03, 0x10000d03, 0x00720900);

	reg = readl(MX35_CCM_BASE_ADDR + MX35_CCM_RCSR);
	/* some fuses provide us vital information about connected hardware */
	if (reg & 0x20000000)
		nand_info.width = 2;	/* 16 bit */
	else
		nand_info.width = 1;	/* 8 bit */

	/*
	 * This platform supports NOR and NAND
	 */
	imx35_add_nand(&nand_info);
	add_cfi_flash_device(DEVICE_ID_DYNAMIC, MX35_CS0_BASE_ADDR, 64 * 1024 * 1024, 0);

	switch ((reg >> 25) & 0x3) {
	case 0x01:		/* NAND is the source */
		devfs_add_partition("nand0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self_raw");
		dev_add_bb_dev("self_raw", "self0");
		devfs_add_partition("nand0", 0x40000, 0x80000, DEVFS_PARTITION_FIXED, "env_raw");
		dev_add_bb_dev("env_raw", "env0");
		break;

	case 0x00:		/* NOR is the source */
		devfs_add_partition("nor0", 0x00000, 0x40000, DEVFS_PARTITION_FIXED, "self0");
		devfs_add_partition("nor0", 0x40000, 0x80000, DEVFS_PARTITION_FIXED, "env0");
		protect_file("/dev/env0", 1);
		break;
	}

	set_silicon_rev(imx_silicon_revision());

	i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
	imx35_add_i2c0(NULL);

	imx35_add_fec(&fec_info);
	add_generic_device("smc911x", DEVICE_ID_DYNAMIC, NULL,	MX35_CS5_BASE_ADDR, MX35_CS5_SIZE,
			IORESOURCE_MEM, NULL);

	imx35_add_mmc0(NULL);

	imx35_add_fb(&ipu_fb_data);

	armlinux_set_bootparams((void *)0x80000100);
	armlinux_set_architecture(MACH_TYPE_MX35_3DS);

	return 0;
}

开发者ID:RobertCNelson，项目名称:barebox-boards，代码行数:53，代码来源:3stack.c

注：本文中的dev_add_bb_dev函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ dev_add_pack函数代码示例发布时间：2022-05-30

C++ devToolsAgent函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19254|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：10006|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8335|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8703|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8650|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9676|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8635|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8008|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8671|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7542|2022-11-06

客服电话

电子邮件

C++ dev_add_bb_dev函数代码示例

示例1: cupid_devices_init

示例2: pcm049_devices_init

示例3: nhk8815_devices_init

示例4: at91sam9n12ek_devices_init

示例5: tx25_devices_init

示例6: pcm049_devices_init

示例7: usb_a9260_devices_init

示例8: at91sam9x5ek_devices_init

示例9: at91sam9261ek_devices_init

示例10: imx25_3ds_devices_init

示例11: at91sam9m10g45ek_devices_init

示例12: vincell_devices_init

示例13: at91sam9m10ihd_devices_init

示例14: nhk8815_devices_init

示例15: eukrea_cpuimx25_devices_init

示例16: at91sam9260ek_devices_init

示例17: pcm049_devices_init

示例18: pcm043_devices_init

示例19: tx51_part_init

示例20: f3s_devices_init

请发表评论

全部评论

上一篇：

下一篇：

PacktPublishing/Python-Machine-Learning-

armancodv/building-energy-model-matlab:

鲁东大学一米网:Win7系统USB驱动器RAM的操

每的笔顺,概括每的笔画,理会每的部首

FGRibreau/import-tweets-to-mastodon: How

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053