本文整理汇总了C++中ctrl_outw函数的典型用法代码示例。如果您正苦于以下问题：C++ ctrl_outw函数的具体用法？C++ ctrl_outw怎么用？C++ ctrl_outw使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了ctrl_outw函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: sci_init_pins_scif
/* For SH7707, SH7709, SH7709A, SH7729, SH7300*/
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
{
unsigned int fcr_val = 0;
#if !defined(CONFIG_CPU_SUBTYPE_SH7300) /* SH7300 doesn't use RTS/CTS */
{
unsigned short data;
/* We need to set SCPCR to enable RTS/CTS */
data = ctrl_inw(SCPCR);
/* Clear out SCP7MD1,0, SCP6MD1,0, SCP4MD1,0*/
ctrl_outw(data&0x0fcf, SCPCR);
}
if (cflag & CRTSCTS)
fcr_val |= SCFCR_MCE;
else {
unsigned short data;
/* We need to set SCPCR to enable RTS/CTS */
data = ctrl_inw(SCPCR);
/* Clear out SCP7MD1,0, SCP4MD1,0,
Set SCP6MD1,0 = {01} (output) */
ctrl_outw((data&0x0fcf)|0x1000, SCPCR);
data = ctrl_inb(SCPDR);
/* Set /RTS2 (bit6) = 0 */
ctrl_outb(data&0xbf, SCPDR);
}
#endif
sci_out(port, SCFCR, fcr_val);
}
开发者ID:BackupTheBerlios，项目名称:tuxap，代码行数:31，代码来源:sh-sci.c
示例2: highlander_setup
/*
* Initialize the board
*/
static void __init highlander_setup(char **cmdline_p)
{
u16 ver = ctrl_inw(PA_VERREG);
int i;
printk(KERN_INFO "Renesas Solutions Highlander %s support.\n",
mach_is_r7780rp() ? "R7780RP-1" :
mach_is_r7780mp() ? "R7780MP" :
"R7785RP");
printk(KERN_INFO "Board version: %d (revision %d), "
"FPGA version: %d (revision %d)\n",
(ver >> 12) & 0xf, (ver >> 8) & 0xf,
(ver >> 4) & 0xf, ver & 0xf);
/*
* Enable the important clocks right away..
*/
for (i = 0; i < ARRAY_SIZE(r7780rp_clocks); i++) {
struct clk *clk = r7780rp_clocks[i];
clk_register(clk);
clk_enable(clk);
}
ctrl_outw(0x0000, PA_OBLED); /* Clear LED. */
if (mach_is_r7780rp())
ctrl_outw(0x0001, PA_SDPOW); /* SD Power ON */
ctrl_outw(ctrl_inw(PA_IVDRCTL) | 0x01, PA_IVDRCTL); /* Si13112 */
pm_power_off = r7780rp_power_off;
}
开发者ID:274914765，项目名称:C，代码行数:37，代码来源:setup.c
示例3: sh7750_perf_counter_stop
static void sh7750_perf_counter_stop(void)
{
ctrl_outw(ctrl_inw(PMCR1) & ~PMCR_PMEN, PMCR1);
ctrl_outw(ctrl_inw(PMCR2) & ~PMCR_PMEN, PMCR2);
unregister_profile_notifier(&sh7750_timer_notifier);
}
开发者ID:3sOx，项目名称:asuswrt-merlin，代码行数:7，代码来源:op_model_sh7750.c
示例4: sh7750_perf_counter_start
static int sh7750_perf_counter_start(void)
{
u16 pmcr;
/* Enable counter 1 */
if (ctr[0].enabled) {
pmcr = ctrl_inw(PMCR1);
WARN_ON(pmcr & PMCR_PMEN);
pmcr &= ~PMCR_PMM_MASK;
pmcr |= ctr[0].event;
ctrl_outw(pmcr | PMCR_ENABLE, PMCR1);
}
/* Enable counter 2 */
if (ctr[1].enabled) {
pmcr = ctrl_inw(PMCR2);
WARN_ON(pmcr & PMCR_PMEN);
pmcr &= ~PMCR_PMM_MASK;
pmcr |= ctr[1].event;
ctrl_outw(pmcr | PMCR_ENABLE, PMCR2);
}
return register_profile_notifier(&sh7750_timer_notifier);
}
开发者ID:3sOx，项目名称:asuswrt-merlin，代码行数:26，代码来源:op_model_sh7750.c
示例5: migor_setup
static void __init migor_setup(char **cmdline_p)
{
/* SMC91C111 - Enable IRQ0 */
ctrl_outw(ctrl_inw(PORT_PJCR) & ~0x0003, PORT_PJCR);
/* KEYSC */
ctrl_outw(ctrl_inw(PORT_PYCR) & ~0x0fff, PORT_PYCR);
ctrl_outw(ctrl_inw(PORT_PZCR) & ~0x0ff0, PORT_PZCR);
ctrl_outw(ctrl_inw(PORT_PSELA) & ~0x4100, PORT_PSELA);
ctrl_outw(ctrl_inw(PORT_HIZCRA) & ~0x4000, PORT_HIZCRA);
ctrl_outw(ctrl_inw(PORT_HIZCRC) & ~0xc000, PORT_HIZCRC);
ctrl_outl(ctrl_inl(MSTPCR2) & ~0x00004000, MSTPCR2);
/* NAND Flash */
ctrl_outw(ctrl_inw(PORT_PXCR) & 0x0fff, PORT_PXCR);
ctrl_outl((ctrl_inl(BSC_CS6ABCR) & ~0x00000600) | 0x00000200,
BSC_CS6ABCR);
/* I2C */
ctrl_outl(ctrl_inl(MSTPCR1) & ~0x00000200, MSTPCR1);
/* Touch Panel - Enable IRQ6 */
ctrl_outw(ctrl_inw(PORT_PZCR) & ~0xc, PORT_PZCR);
ctrl_outw((ctrl_inw(PORT_PSELA) | 0x8000), PORT_PSELA);
ctrl_outw((ctrl_inw(PORT_HIZCRC) & ~0x4000), PORT_HIZCRC);
}
开发者ID:274914765，项目名称:C，代码行数:26，代码来源:setup.c
示例6: init_se7722_IRQ
/*
* Initialize IRQ setting
*/
void __init init_se7722_IRQ(void)
{
int i, irq;
ctrl_outw(0, IRQ01_MASK); /* disable all irqs */
ctrl_outw(0x2000, 0xb03fffec); /* mrshpc irq enable */
for (i = 0; i < SE7722_FPGA_IRQ_NR; i++) {
irq = create_irq();
if (irq < 0)
return;
se7722_fpga_irq[i] = irq;
set_irq_chip_and_handler_name(se7722_fpga_irq[i],
&se7722_irq_chip,
handle_level_irq, "level");
set_irq_chip_data(se7722_fpga_irq[i], (void *)i);
}
set_irq_chained_handler(IRQ0_IRQ, se7722_irq_demux);
set_irq_type(IRQ0_IRQ, IRQ_TYPE_LEVEL_LOW);
set_irq_chained_handler(IRQ1_IRQ, se7722_irq_demux);
set_irq_type(IRQ1_IRQ, IRQ_TYPE_LEVEL_LOW);
}
开发者ID:AdrianHuang，项目名称:uclinux-robutest，代码行数:29，代码来源:irq.c
示例7: sci_init_pins_scif
/* For SH7707, SH7709, SH7709A, SH7729 */
static void sci_init_pins_scif(struct sci_port* port, unsigned int cflag)
{
unsigned int fcr_val = 0;
{
unsigned short data;
/* We need to set SCPCR to enable RTS/CTS */
data = ctrl_inw(SCPCR);
/* Clear out SCP7MD1,0, SCP6MD1,0, SCP4MD1,0*/
ctrl_outw(data&0x0fcf, SCPCR);
}
if (cflag & CRTSCTS)
fcr_val |= SCFCR_MCE;
else {
unsigned short data;
/* We need to set SCPCR to enable RTS/CTS */
data = ctrl_inw(SCPCR);
/* Clear out SCP7MD1,0, SCP4MD1,0,
Set SCP6MD1,0 = {01} (output) */
ctrl_outw((data&0x0fcf)|0x1000, SCPCR);
data = ctrl_inb(SCPDR);
/* Set /RTS2 (bit6) = 0 */
ctrl_outb(data&0xbf, SCPDR);
}
sci_out(port, SCFCR, fcr_val);
}
开发者ID:nhanh0，项目名称:hah，代码行数:30，代码来源:sh-sci.c
示例8: init_hs7751rvoip_IRQ
/*
* Initialize IRQ setting
*/
void __init init_hs7751rvoip_IRQ(void)
{
int i;
/* IRL0=ON HOOK1
* IRL1=OFF HOOK1
* IRL2=ON HOOK2
* IRL3=OFF HOOK2
* IRL4=Ringing Detection
* IRL5=CODEC
* IRL6=Ethernet
* IRL7=Ethernet Hub
* IRL8=USB Communication
* IRL9=USB Connection
* IRL10=USB DMA
* IRL11=CF Card
* IRL12=PCMCIA
* IRL13=PCI Slot
*/
ctrl_outw(0x9876, IRLCNTR1);
ctrl_outw(0xdcba, IRLCNTR2);
ctrl_outw(0x0050, IRLCNTR4);
ctrl_outw(0x4321, IRLCNTR5);
for (i=0; i<14; i++)
make_hs7751rvoip_irq(i);
}
开发者ID:1x23，项目名称:unifi-gpl，代码行数:30，代码来源:irq.c
示例9: se7721_setup
static void __init se7721_setup(char **cmdline_p)
{
/* for USB */
ctrl_outw(0x0000, 0xA405010C); /* PGCR */
ctrl_outw(0x0000, 0xA405010E); /* PHCR */
ctrl_outw(0x00AA, 0xA4050118); /* PPCR */
ctrl_outw(0x0000, 0xA4050124); /* PSELA */
}
开发者ID:janrinze，项目名称:loox7xxport，代码行数:8，代码来源:setup.c
示例10: landisk_outw
void landisk_outw(u16 value, unsigned long port)
{
if (PXSEG(port))
ctrl_outw(value, port);
else if (is_pci_ioaddr(port))
ctrl_outw(value, pci_ioaddr(port));
else
maybebadio(port);
}
开发者ID:420GrayFox，项目名称:dsl-n55u-bender，代码行数:9，代码来源:io.c
示例11: init_shmse_IRQ
void __init init_shmse_IRQ(void)
{
ctrl_outw(0x0028, 0xb0a00000); // mode set [active low].
ctrl_outw(0x000a, INTC_ICR1); // IRQ mode; IRQ0,1 enable.
/* PC_IRQ[0-3] -> IRQ0 (32) */
make_ipr_irq( IRQ0_IRQ, IRQ0_IPR_ADDR, IRQ0_IPR_POS, 0x0f-IRQ0_IRQ);
/* A_IRQ[0-3] -> IRQ1 (33) */
make_ipr_irq( IRQ1_IRQ, IRQ1_IPR_ADDR, IRQ1_IPR_POS, 0x0f-IRQ1_IRQ);
}
开发者ID:SimonKagstrom，项目名称:mci500h-linux-2.4.27，代码行数:9，代码来源:setup_shmse.c
示例12: hs7751rvoip_outw
void hs7751rvoip_outw(unsigned short value, unsigned long port)
{
if (PXSEG(port))
ctrl_outw(value, port);
else if (is_pci_ioaddr(port) || shifted_port(port))
ctrl_outw(value, pci_ioaddr(port));
else
maybebadio(port);
}
开发者ID:3sOx，项目名称:asuswrt-merlin，代码行数:9，代码来源:io.c
示例13: titan_outw
void titan_outw(u16 value, unsigned long port)
{
if (PXSEG(port))
ctrl_outw(value, port);
else if (port >= 0x2000)
ctrl_outw(value, port2adr(port));
else
maybebadio(port);
}
开发者ID:mikuhatsune001，项目名称:linux2.6.32，代码行数:9，代码来源:io.c
示例14: ap320_wvga_power_off
static void ap320_wvga_power_off(void *board_data)
{
/* backlight */
ctrl_outw(0, FPGA_BKLREG);
gpio_set_value(GPIO_PTS3, 1);
/* ASD AP-320/325 LCD OFF */
ctrl_outw(0, FPGA_LCDREG);
}
开发者ID:AdrianHuang，项目名称:uclinux-robutest，代码行数:9，代码来源:setup.c
示例15: ap320_wvga_power_on
static void ap320_wvga_power_on(void *board_data)
{
msleep(100);
/* ASD AP-320/325 LCD ON */
ctrl_outw(FPGA_LCDREG_VAL, FPGA_LCDREG);
/* backlight */
gpio_set_value(GPIO_PTS3, 0);
ctrl_outw(0x100, FPGA_BKLREG);
}
开发者ID:AdrianHuang，项目名称:uclinux-robutest，代码行数:11，代码来源:setup.c
示例16: titan_outb
void titan_outb(u8 value, unsigned long port)
{
if (PXSEG(port))
ctrl_outb(value, port);
else
ctrl_outw(value, port2adr(port));
}
开发者ID:mikuhatsune001，项目名称:linux2.6.32，代码行数:7，代码来源:io.c
示例17: disable_ipr_irq
static void disable_ipr_irq(unsigned int irq)
{
struct ipr_data *p = get_irq_chip_data(irq);
unsigned long addr = get_ipr_desc(irq)->ipr_offsets[p->ipr_idx];
/* Set the priority in IPR to 0 */
ctrl_outw(ctrl_inw(addr) & (0xffff ^ (0xf << p->shift)), addr);
}
开发者ID:LouZiffer，项目名称:m900_kernel_cupcake-SDX，代码行数:7，代码来源:ipr.c
示例18: enable_ipr_irq
static void enable_ipr_irq(unsigned int irq)
{
struct ipr_data *p = get_irq_chip_data(irq);
unsigned long addr = get_ipr_desc(irq)->ipr_offsets[p->ipr_idx];
/* Set priority in IPR back to original value */
ctrl_outw(ctrl_inw(addr) | (p->priority << p->shift), addr);
}
开发者ID:LouZiffer，项目名称:m900_kernel_cupcake-SDX，代码行数:7，代码来源:ipr.c
示例19: camera_power
static int camera_power(struct device *dev, int mode)
{
int ret;
if (mode) {
long rate;
camera_clk = clk_get(NULL, "video_clk");
if (IS_ERR(camera_clk))
return PTR_ERR(camera_clk);
rate = clk_round_rate(camera_clk, CEU_MCLK_FREQ);
ret = clk_set_rate(camera_clk, rate);
if (ret < 0)
goto eclkrate;
/* set DRVCRB
*
* use 1.8 V for VccQ_VIO
* use 2.85V for VccQ_SR
*/
ctrl_outw((ctrl_inw(DRVCRB) & ~0x0003) | 0x0001, DRVCRB);
/* reset clear */
ret = gpio_request(GPIO_PTB4, NULL);
if (ret < 0)
goto eptb4;
ret = gpio_request(GPIO_PTB7, NULL);
if (ret < 0)
goto eptb7;
ret = gpio_direction_output(GPIO_PTB4, 1);
if (!ret)
ret = gpio_direction_output(GPIO_PTB7, 1);
if (ret < 0)
goto egpioout;
msleep(1);
ret = clk_enable(camera_clk); /* start VIO_CKO */
if (ret < 0)
goto eclkon;
return 0;
}
ret = 0;
clk_disable(camera_clk);
eclkon:
gpio_set_value(GPIO_PTB7, 0);
egpioout:
gpio_set_value(GPIO_PTB4, 0);
gpio_free(GPIO_PTB7);
eptb7:
gpio_free(GPIO_PTB4);
eptb4:
eclkrate:
clk_put(camera_clk);
return ret;
}
开发者ID:AdrianHuang，项目名称:uclinux-robutest，代码行数:60，代码来源:setup.c
示例20: sh7760_ac97_init
static int __init sh7760_ac97_init(void)
{
int ret;
unsigned short ipsel;
/* enable both AC97 controllers in pinmux reg */
ipsel = ctrl_inw(IPSEL);
ctrl_outw(ipsel | (3 << 10), IPSEL);
ret = -ENOMEM;
sh7760_ac97_snd_device = platform_device_alloc("soc-audio", -1);
if (!sh7760_ac97_snd_device)
goto out;
platform_set_drvdata(sh7760_ac97_snd_device,
&sh7760_ac97_snd_devdata);
sh7760_ac97_snd_devdata.dev = &sh7760_ac97_snd_device->dev;
ret = platform_device_add(sh7760_ac97_snd_device);
if (ret)
platform_device_put(sh7760_ac97_snd_device);
out:
return ret;
}
开发者ID:274914765，项目名称:C，代码行数:25，代码来源:sh7760-ac97.c
注：本文中的ctrl_outw函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。 |
客服电话
APP下载
官方微信
请发表评论