本文整理汇总了C++中RTC_SetAlarm函数的典型用法代码示例。如果您正苦于以下问题：C++ RTC_SetAlarm函数的具体用法？C++ RTC_SetAlarm怎么用？C++ RTC_SetAlarm使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了RTC_SetAlarm函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: RTC_AlarmConfig
/**
* @brief Configures the RTC Alarm.
* @param None
* @retval None
*/
void RTC_AlarmConfig(void)
{
EXTI_InitTypeDef EXTI_InitStructure;
RTC_AlarmTypeDef RTC_AlarmStructure;
NVIC_InitTypeDef NVIC_InitStructure;
/* EXTI configuration */
EXTI_ClearITPendingBit(EXTI_Line17);
EXTI_InitStructure.EXTI_Line = EXTI_Line17;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable the RTC Alarm Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_Alarm_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
/* Set the alarmA Masks */
RTC_AlarmStructure.RTC_AlarmMask = RTC_AlarmMask_All;
RTC_SetAlarm(RTC_Format_BIN, RTC_Alarm_A, &RTC_AlarmStructure);
/* Set AlarmA subseconds and enable SubSec Alarm : generate 8 interripts per Second */
RTC_AlarmSubSecondConfig(RTC_Alarm_A, 0xFF, RTC_AlarmSubSecondMask_SS14_5);
/* Enable AlarmA interrupt */
RTC_ITConfig(RTC_IT_ALRA, ENABLE);
/* Enable the alarmA */
RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
}
开发者ID:jongtao，项目名称:stm32l-dev-chain，代码行数:40，代码来源:main.c
示例2: RTC_Alarm_Set
//初始化闹钟
//以1970年1月1日为基准
//1970~2099年为合法年份
//syear,smon,sday,hour,min,sec：闹钟的年月日时分秒
//返回值:0,成功;其他:错误代码.
u8 RTC_Alarm_Set(u16 syear,u8 smon,u8 sday,u8 hour,u8 min,u8 sec)
{
u16 t;
u32 seccount=0;
if(syear<1970||syear>2099)return 1;
for(t=1970;t<syear;t++) //把所有年份的秒钟相加
{
if(Is_Leap_Year(t))seccount+=31622400;//闰年的秒钟数
else seccount+=31536000; //平年的秒钟数
}
smon-=1;
for(t=0;t<smon;t++) //把前面月份的秒钟数相加
{
seccount+=(u32)mon_table[t]*86400;//月份秒钟数相加
if(Is_Leap_Year(syear)&&t==1)seccount+=86400;//闰年2月份增加一天的秒钟数
}
seccount+=(u32)(sday-1)*86400;//把前面日期的秒钟数相加
seccount+=(u32)hour*3600;//小时秒钟数
seccount+=(u32)min*60; //分钟秒钟数
seccount+=sec;//最后的秒钟加上去
//设置时钟
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE); //使能PWR和BKP外设时钟
PWR_BackupAccessCmd(ENABLE); //使能后备寄存器访问
//上面三步是必须的!
RTC_SetAlarm(seccount);
RTC_WaitForLastTask(); //等待最近一次对RTC寄存器的写操作完成
return 0;
}
开发者ID:wangdie1，项目名称:ElectronicDesignContest，代码行数:36，代码来源:rtc.c
示例3: EnterSTANDBYMode
/**
* @brief Enters STANDBY mode, RTC Alarm within 3 second or an external RESET
* will wake-up the system from STANDBY
* @param None
* @retval None
*/
static void EnterSTANDBYMode(void)
{
RTC_AlarmTypeDef RTC_AlarmStructure;
RTC_TimeTypeDef RTC_TimeStructure;
/* Disable the Alarm A */
RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
/* Get the current time */
RTC_GetTime(RTC_Format_BIN, &RTC_TimeStructure);
/* Set the alarm to current time + 3s */
RTC_AlarmStructure.RTC_AlarmTime.RTC_H12 = RTC_TimeStructure.RTC_H12;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Hours = RTC_TimeStructure.RTC_Hours;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Minutes = RTC_TimeStructure.RTC_Minutes;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Seconds = (RTC_TimeStructure.RTC_Seconds + 0x3) % 60;
RTC_AlarmStructure.RTC_AlarmDateWeekDay = 31;
RTC_AlarmStructure.RTC_AlarmDateWeekDaySel = RTC_AlarmDateWeekDaySel_Date;
RTC_AlarmStructure.RTC_AlarmMask = RTC_AlarmMask_DateWeekDay | RTC_AlarmMask_Hours | RTC_AlarmMask_Minutes;
RTC_SetAlarm(RTC_Format_BIN, RTC_Alarm_A, &RTC_AlarmStructure);
/* Enable RTC Alarm A Interrupt: this Interrupt will wake-up the system from
STANDBY mode (RTC Alarm IT not enabled in NVIC) */
RTC_ITConfig(RTC_IT_ALRA, ENABLE);
/* Enable the Alarm A */
RTC_AlarmCmd(RTC_Alarm_A, ENABLE);
/* Clear RTC Alarm Flag */
RTC_ClearFlag(RTC_FLAG_ALRAF);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
}
开发者ID:yogiyi，项目名称:BP_STM32F030，代码行数:40，代码来源:main.c
示例4: sleep
/***************************************************************************
Declaration : void sleep(char wdt_prescaler)
Description : Sleep until WDT interrupt controlled by wdt_prescaler
***************************************************************************/
void sleep(int data_ms, char mode)
{
/* Enable the RTC Alarm interrupt */
RTC_ITConfig(RTC_IT_ALR, ENABLE);
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
/* Alarm in data_ms */
// RTC_SetAlarm(RTC_GetCounter()+ data_ms<<5);
RTC_SetAlarm(RTC_GetCounter()+ data_ms);
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
/* Request to enter STOP mode with regulator ON */
PWR_EnterSTOPMode(PWR_Regulator_ON, PWR_STOPEntry_WFI);
/* At this stage the system has resumed from STOP mode -------------------*/
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select PLL
as system clock source (HSE and PLL are disabled in STOP mode) */
/* Enable the RTC Alarm interrupt */
SYSCLKConfig_STOP();
RTC_ITConfig(RTC_IT_ALR, DISABLE);
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
}
开发者ID:QXED，项目名称:MutiNodesBy2.4GWireless，代码行数:36，代码来源:mcu.c
示例5: RtcSetAlarmConfig
static void RtcSetAlarmConfig( void )
{
EXTI_InitTypeDef EXTI_InitStructure;
RTC_AlarmTypeDef RTC_AlarmStructure;
NVIC_InitTypeDef NVIC_InitStructure;
/* EXTI configuration */
EXTI_ClearITPendingBit( EXTI_Line17 );
EXTI_InitStructure.EXTI_Line = EXTI_Line17;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init( &EXTI_InitStructure );
/* Enable the RTC Alarm Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = RTC_Alarm_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
//NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init( &NVIC_InitStructure );
/* Set the alarmA Masks */
RTC_AlarmStructure.RTC_AlarmMask = RTC_AlarmMask_DateWeekDay;
RTC_SetAlarm( RTC_Format_BIN, RTC_Alarm_A, &RTC_AlarmStructure );
/* Enable AlarmA interrupt */
RTC_ITConfig( RTC_IT_ALRA, DISABLE );
/* Enable the alarmA */
RTC_AlarmCmd( RTC_Alarm_A, DISABLE );
}
开发者ID:davincicloud-kr，项目名称:im-l200，代码行数:32，代码来源:rtc-board.c
示例6: RTCAlarm_IRQHandler
void RTCAlarm_IRQHandler(void)
{
uint32_t RTC_counter;
RTC->CRL &= (uint16_t)RTC_FLAG_ALR;
EXTI->PR = EXTI_Line17;
RTC_counter = RTC_GetCounter();
if(RTC_counter >= (sysCfg.sleepTime + sleepTimeOld))
{
sleepTimeOld = RTC_counter;
sysEventFlag |= MCU_WAKEUP_FLAG;
InitTimeout(&MCU_WakeupTimeout,TIME_SEC(60));
}
if(GET_ACC_PIN == ACC_ON)
{
POWER_EN_SET_OUTPUT;
POWER_EN_PIN_SET;
timepowerOffDelay = RTC_counter;
}
else if(RTC_counter >= (sysCfg.powerOffDelayTime + timepowerOffDelay))
{
POWER_EN_SET_INPUT;
timepowerOffDelay = RTC_counter;
}
RTC_SetAlarm((RTC_counter + ALARM_TIME));
sysEventFlag |= RTC_ALARM_FLAG;
}
开发者ID:PascalSI，项目名称:ampm_car_tracker，代码行数:28，代码来源:rtc.c
示例7: HAL_RTC_Set_UnixAlarm
void HAL_RTC_Set_UnixAlarm(time_t value)
{
RTC_AlarmTypeDef RTC_AlarmStructure;
time_t alarm_time = HAL_RTC_Get_UnixTime() + value;
struct tm *alarm_time_tm;
alarm_time_tm = localtime(&alarm_time);
/* Disable the Alarm A */
RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
RTC_AlarmStructure.RTC_AlarmTime.RTC_Hours = alarm_time_tm->tm_hour;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Minutes = alarm_time_tm->tm_min;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Seconds = alarm_time_tm->tm_sec;
RTC_AlarmStructure.RTC_AlarmDateWeekDay = alarm_time_tm->tm_mday;
RTC_AlarmStructure.RTC_AlarmDateWeekDaySel = RTC_AlarmDateWeekDaySel_Date;
RTC_AlarmStructure.RTC_AlarmMask = RTC_AlarmMask_None;
/* Configure the RTC Alarm A register */
RTC_SetAlarm(RTC_Format_BIN, RTC_Alarm_A, &RTC_AlarmStructure);
/* Enable the RTC Alarm A Interrupt */
RTC_ITConfig(RTC_IT_ALRA, ENABLE);
/* Enable the Alarm A */
RTC_AlarmCmd(RTC_Alarm_A, ENABLE);
/* Clear RTC Alarm Flag */
RTC_ClearFlag(RTC_FLAG_ALRAF);
}
开发者ID:RobertNewkirk，项目名称:particle，代码行数:31，代码来源:rtc_hal.c
示例8: main
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* Setup the microcontroller system. Initialize the Embedded Flash Interface,
initialize the PLL and update the SystemFrequency variable. */
SystemInit();
/* Initialize LEDs and Key Button mounted on STM3210X-EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_PBInit(Button_KEY, Mode_EXTI);
/* Enable PWR and BKP clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE);
/* Configure EXTI Line to generate an interrupt on falling edge */
EXTI_Configuration();
/* Configure RTC clock source and prescaler */
RTC_Configuration();
/* NVIC configuration */
NVIC_Configuration();
/* Configure the SysTick to generate an interrupt each 1 millisecond */
SysTick_Configuration();
/* Turn on LED1 */
STM_EVAL_LEDOn(LED1);
while (1)
{
/* Insert 1.5 second delay */
Delay(1500);
/* Wait till RTC Second event occurs */
RTC_ClearFlag(RTC_FLAG_SEC);
while(RTC_GetFlagStatus(RTC_FLAG_SEC) == RESET);
/* Alarm in 3 second */
RTC_SetAlarm(RTC_GetCounter()+ 3);
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
/* Turn off LED1 */
STM_EVAL_LEDOff(LED1);
/* Request to enter STOP mode with regulator in low power mode*/
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
/* At this stage the system has resumed from STOP mode -------------------*/
/* Turn on LED1 */
STM_EVAL_LEDOn(LED1);
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SYSCLKConfig_STOP();
}
}
开发者ID:DerekTan，项目名称:STM32F107_ucosIII，代码行数:64，代码来源:main.c
示例9: main
/*******************************************************************************
* Function Name : main
* Description : Main program.
* Input : None
* Output : None
* Return : None
*******************************************************************************/
int main(void)
{
#ifdef DEBUG
debug();
#endif
/* Clock configuration */
RCC_Configuration();
/* Enable PWR and BKP clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE);
/* GPIO configuration */
GPIO_Configuration();
/* Configure EXTI Line to generate an interrupt on falling edge */
EXTI_Configuration();
/* Configure RTC clock source and prescaler */
RTC_Configuration();
/* NVIC configuration */
NVIC_Configuration();
/* Configure the SysTick to generate an interrupt each 1 millisecond */
SysTick_Configuration();
/* Turn on led connected to GPIO_LED Pin6 */
GPIO_SetBits(GPIO_LED, GPIO_Pin_6);
while (1)
{
/* Insert 1.5 second delay */
Delay(1500);
/* Wait till RTC Second event occurs */
RTC_ClearFlag(RTC_FLAG_SEC);
while(RTC_GetFlagStatus(RTC_FLAG_SEC) == RESET);
/* Alarm in 3 second */
RTC_SetAlarm(RTC_GetCounter()+ 3);
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
/* Turn off led connected to GPIO_LED Pin6 */
GPIO_ResetBits(GPIO_LED, GPIO_Pin_6);
/* Request to enter STOP mode with regulator in low power mode*/
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
/* At this stage the system has resumed from STOP mode -------------------*/
/* Turn on led connected to GPIO_LED Pin6 */
GPIO_SetBits(GPIO_LED, GPIO_Pin_6);
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SYSCLKConfig_STOP();
}
}
开发者ID:timmy00274672，项目名称:STM32-Learning，代码行数:66，代码来源:main.c
示例10: rtc_timer_start
void rtc_timer_start(u32 alarmValue)
{
//enable BKP and PWR, Clock
RCC_APB1PeriphClockCmd(RCC_APB1Periph_BKP|RCC_APB1Periph_PWR , ENABLE);
// RTC clock source configuration
PWR_BackupAccessCmd(ENABLE); //Allow access to BKP Domain
RCC_LSEConfig(RCC_LSE_ON); //Enable LSE OSC
while(RCC_GetFlagStatus(RCC_FLAG_LSERDY)==RESET); //Wait till LSE is ready
RCC_RTCCLKConfig(RCC_RTCCLKSource_LSE); //Select the RTC Clock Source
RCC_RTCCLKCmd(ENABLE); //enable RTC
// RTC configuration
// Wait for RTC APB registers synchronisation
RTC_WaitForSynchro();
RTC_SetPrescaler(0); //Set the RTC time base to 30.5us
RTC_WaitForLastTask(); //Wait until last write operation on RTC registers has finished
//Set the RTC time counter to 0
RTC_SetCounter(0);
RTC_WaitForLastTask();
// Set the RTC time alarm(the length of slot)
RTC_SetAlarm(alarmValue);
RTC_WaitForLastTask();
//interrupt when reach alarm value
RTC_ClearFlag(RTC_IT_ALR);
RTC_ITConfig(RTC_IT_ALR, ENABLE);
//Configures EXTI line 17 to generate an interrupt on rising edge(alarm interrupt to wakeup board)
EXTI_ClearITPendingBit(EXTI_Line17);
EXTI_InitTypeDef EXTI_InitStructure;
EXTI_InitStructure.EXTI_Line = EXTI_Line17;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
//Configure RTC global interrupt:
//Configure NVIC: Preemption Priority = 1 and Sub Priority = 1
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_InitStructure.NVIC_IRQChannel = RTC_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
//Configure RTC Alarm interrupt:
//Configure NVIC: Preemption Priority = 0 and Sub Priority = 1
NVIC_InitStructure.NVIC_IRQChannel = RTCAlarm_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
开发者ID:Babody，项目名称:openwsn-fw，代码行数:57，代码来源:rtc_timer.c
示例11: RTC_AlarmSet
/*
************************************************************
* 函数名称： RTC_AlarmSet
*
* 函数功能： RTC闹钟初始化
*
* 入口参数： sec：秒值
*
* 返回参数： 无
*
* 说明： 写入一个32bit的秒数，来代表时间。当与RTC_CNT相等时产生闹钟中断
************************************************************
*/
void RTC_AlarmSet(unsigned int sec)
{
RTC_WaitForLastTask();
RTC_SetAlarm(sec);
RTC_WaitForLastTask();
RTC_WaitForSynchro(); //等待RTC寄存器同步
}
开发者ID:yzfcer，项目名称:wind-os，代码行数:22，代码来源:rtc.c
示例12: main
/*******************************************************************************
* @brief main routine
******************************************************************************/
int main (void)
{
SIM_Init (SIM_MODULE_FRDM_RTC_WATCH_CONFIG);
MCG_LITE_Init (MCG_LITE_HIRC_48MHZ);
// OSC module initialization
OSC_Init(OSC_MODULE_OSCERCLK_ON_STOPMODE_ON_CONFIG(OSC_SC16P));
MCG_ExtClkType(OSC_REQST);
MCG_CrystalMode(LOW_POWER_OSC);
MCG_CrystalFreqRangeSel(LOW_FREQ_RANGE);
MCG_WaitOscInit();
// LEDs initialization
PORT_Init (PORTD, PORT_MODULE_ALT1_MODE, PIN_5, 0, NULL);
GPIO_Init (GPIOD, GPIO_PIN_OUTPUT, PIN_5);
GPIO_Set (GPIOD, PIN_5);
PORT_Init (PORTE, PORT_MODULE_ALT1_MODE, PIN_31, 0, NULL);
GPIO_Init (GPIOE, GPIO_PIN_OUTPUT, PIN_31);
GPIO_Set (GPIOE, PIN_31);
// VLLx, VCAPx pins disable
PORT_Init(PORTC, PORT_MODULE_DISABLED_MODE, PIN_20|PIN_21|PIN_22|PIN_23, 0, NULL);
// SLCD pin configuration
PORT_Init(PORTE, PORT_MODULE_ALT0_MODE, PIN_20|PIN_21, 0, NULL);
PORT_Init(PORTB, PORT_MODULE_ALT0_MODE, PIN_18|PIN_19, 0, NULL);
PORT_Init(PORTC, PORT_MODULE_ALT0_MODE, PIN_0|PIN_4|PIN_6|PIN_7, 0, NULL);
PORT_Init(PORTD, PORT_MODULE_ALT0_MODE, PIN_0|PIN_2|PIN_3|PIN_4, 0, NULL);
// SLCD initialization
LCD_Init (LCD_FRDM_CONFIG, \
LCD_FRONT_PLANE_PINS_FRDM_KL43, \
LCD_BACK_PLANE_PINS_FRDM_KL43, \
LCD_ASSIGN_BACK_PLANES_FRDM_KL43);
LCD_Delete_Char(0);
LCD_Delete_Char(1);
LCD_Delete_Char(2);
LCD_Delete_Char(3);
// Set the time according to system clock
BUILD_DATE_TIME(time);
// RTC initialization
RTC_Init (RTC_MODULE_FRDM_RTC_WATCH_CONFIG, RTC_MkTime (&time), 3, rtc_callback);
RTC_SetAlarm (RTC_GetTime ()+alarm_interval);
// Write time to the LCD
lcd_settime(&time);
__enable_irq();
while (1)
{
}
}
开发者ID:Capstone46，项目名称:Freescale，代码行数:55，代码来源:frdm_rtc_watch_test.c
示例13: radiotimer_schedule
void radiotimer_schedule(uint16_t offset) {
RTC_ITConfig(RTC_IT_ALR, DISABLE);
//need to disable radio also in case that a radio interrupt is happening
// Set the RTC alarm(RTC timer will alarm at next state of slot)
RTC_SetAlarm(offset);
RTC_WaitForLastTask();
//set radiotimer irpstatus
radiotimer_vars.overflowORcompare = RADIOTIMER_COMPARE;
RTC_ClearFlag(RTC_IT_ALR);
RTC_ITConfig(RTC_IT_ALR, ENABLE);
}
开发者ID:Babody，项目名称:openwsn-fw，代码行数:13，代码来源:radiotimer.c
示例14: DecrementAlarmMinutes
void DecrementAlarmMinutes()
{
int currentAlarmHour = AlarmAStruct.RTC_AlarmTime.RTC_Hours;
int currentAlarmMinute = AlarmAStruct.RTC_AlarmTime.RTC_Minutes;
currentAlarmHour--;
if(currentAlarmHour <= -1) {
currentAlarmHour = 23;
}
AlarmAStruct.RTC_AlarmTime.RTC_Hours = currentAlarmHour;
AlarmAStruct.RTC_AlarmTime.RTC_Minutes = currentAlarmMinute;
AlarmAStruct.RTC_AlarmTime.RTC_Seconds = 0x00;
AlarmAStruct.RTC_AlarmMask = RTC_AlarmMask_DateWeekDay;
RTC_SetAlarm(RTC_Format_BIN,RTC_Alarm_A,&AlarmAStruct);
}
开发者ID:jordantday，项目名称:Elec299AlarmClock，代码行数:14，代码来源:main.c
示例15: rtc_callback
/***************************************************************************//*!
* @brief RTC Callback function (second interrupt, alarm interrupt).
******************************************************************************/
void rtc_callback (RTC_CALLBACK_TYPE type)
{
if (type == TAF_CALLBACK)
{
RTC_SetAlarm (RTC_GetTime()+alarm_interval);
GPIO_Tgl (GPIOE, PIN_31);
}
if (type == TSF_CALLBACK)
{
RTC_GmTime (RTC_GetTime(),&time);
lcd_settime(&time);
GPIO_Tgl (GPIOD, PIN_5);
}
}
开发者ID:Capstone46，项目名称:Freescale，代码行数:17，代码来源:frdm_rtc_watch_test.c
示例16: radiotimer_cancel
void radiotimer_cancel() {
RTC_ITConfig(RTC_IT_ALR, DISABLE);
//need to disable radio also in case that a radio interrupt is happening
// set RTC alarm (slotlength)
RTC_SetAlarm(radiotimer_vars.currentSlotPeriod);
RTC_WaitForLastTask();
//set radiotimer irpstatus
radiotimer_vars.overflowORcompare = RADIOTIMER_OVERFLOW;
RTC_ClearFlag(RTC_IT_ALR);
RTC_ITConfig(RTC_IT_ALR, ENABLE);
}
开发者ID:Babody，项目名称:openwsn-fw，代码行数:14，代码来源:radiotimer.c
示例17: TIM2_IRQHandler
void TIM2_IRQHandler(void)
{
if ( TIM_GetITStatus(TIM2 , TIM_IT_Update) != RESET )
{
TIM_ClearITPendingBit(TIM2 , TIM_FLAG_Update);
/////////////////////////////////////////////////////////////////
// Power OFF GPS and GSM before go into standby mode
/////////////////////////////////////////////////////////////////
GSM_TurnOnOff_delay();
#ifdef USE_STM32_GPS_BOARD_VB
GPSPowerOff();
GSM_PowerOff();
#endif
/* Wait till RTC Second event occurs */
RTC_ClearFlag(RTC_FLAG_SEC);
while(RTC_GetFlagStatus(RTC_FLAG_SEC) == RESET);
// normal working state
if(BKP_TRUE == BKP_ReadBackupRegister(BKP_DR1))
{
/* Set the RTC Alarm after xx s */
DEBUG("in timer2 bkptrue %d\n", (BKP_ReadBackupRegister(BKP_DR4) + BKP_ReadBackupRegister(BKP_DR4) <<16));
RTC_SetAlarm(RTC_GetCounter()+ ((BKP_ReadBackupRegister(BKP_DR4) + BKP_ReadBackupRegister(BKP_DR4) <<16)/SLEEP_TIM2_RATIO));
}
else
{
DEBUG("in timer2 bkpfalse\n");
RTC_SetAlarm(RTC_GetCounter()+ (SLEEP_NORMAL_SEC/SLEEP_TIM2_RATIO));
}
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
}
}
开发者ID:fidiaslothes，项目名称:stm32gps，代码行数:37，代码来源:stm32f10x_it.c
示例18: SetAlarm
/**
* @brief Sets the RTC Alarm Register Value
* @param Hours, Minutes and Seconds data
* @retval : None
*/
void SetAlarm(uint8_t Hour,uint8_t Minute, uint8_t Seconds)
{
uint32_t CounterValue;
CounterValue=((Hour * 3600)+ (Minute * 60)+Seconds);
if(CounterValue == 0)
{
CounterValue = SECONDS_IN_DAY;
}
RTC_WaitForLastTask();
RTC_SetAlarm(CounterValue);
RTC_WaitForLastTask();
}
开发者ID:namnguyendsn，项目名称:jupiter_packet，代码行数:20，代码来源:clock_calendar.c
示例19: SetAlarm
/*******************************************************************************
* Function Name : SetAlarm
* Description : Sets the RTC Alarm Register Value
* Input : Hours, Minutes and Seconds data
* Output : None
* Return : None
*******************************************************************************/
void SetAlarm(u8 u8_Hour,u8 u8_Minute, u8 u8_Seconds)
{
u32 u32_CounterValue;
u32_CounterValue=((u8_Hour * 3600)+ (u8_Minute * 60)+u8_Seconds);
if(u32_CounterValue == 0)
{
u32_CounterValue = SECONDS_IN_DAY;
}
RTC_WaitForLastTask();
RTC_SetAlarm(u32_CounterValue);
RTC_WaitForLastTask();
}
开发者ID:FlameN，项目名称:STM32RUNO，代码行数:22，代码来源:clock_calendar.c
示例20: cancelAlarm
void cancelAlarm(void)
{
#ifndef PRECISION_IN_MS
RTC_WaitForLastTask();
RTC_SetAlarm(0);
RTC_WaitForLastTask();
RTC_ITConfig(RTC_IT_ALR, DISABLE);
RTC_WaitForLastTask();
RTC_ClearITPendingBit(RTC_IT_ALR);
RTC_WaitForLastTask();
#else
alarm = 0;
#endif
alarmProc = NULL;
}
开发者ID:running1919，项目名称:qianlab，代码行数:15，代码来源:clock.c
注：本文中的RTC_SetAlarm函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。 |
客服电话
APP下载
官方微信
请发表评论