C++ REG_PORT函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中REG_PORT函数的典型用法代码示例。如果您正苦于以下问题：C++ REG_PORT函数的具体用法？C++ REG_PORT怎么用？C++ REG_PORT使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了REG_PORT函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: mv88e6xxx_set_port_state

static int mv88e6xxx_set_port_state(struct dsa_switch *ds, int port, u8 state)
{
	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
	int reg, ret;
	u8 oldstate;

	mutex_lock(&ps->smi_mutex);

	reg = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_CONTROL);
	if (reg < 0)
		goto abort;

	oldstate = reg & PORT_CONTROL_STATE_MASK;
	if (oldstate != state) {
		/* Flush forwarding database if we're moving a port
		 * from Learning or Forwarding state to Disabled or
		 * Blocking or Listening state.
		 */
		if (oldstate >= PORT_CONTROL_STATE_LEARNING &&
		    state <= PORT_CONTROL_STATE_BLOCKING) {
			ret = _mv88e6xxx_flush_fid(ds, ps->fid[port]);
			if (ret)
				goto abort;
		}
		reg = (reg & ~PORT_CONTROL_STATE_MASK) | state;
		ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), PORT_CONTROL,
					   reg);
	}

abort:
	mutex_unlock(&ps->smi_mutex);
	return ret;
}

开发者ID:RealJohnGalt，项目名称:linux，代码行数:33，代码来源:mv88e6xxx.c

示例2: mv88e6123_61_65_switch_reset

static int mv88e6123_61_65_switch_reset(struct dsa_switch *ds)
{
	int i;
	int ret;

	for (i = 0; i < 8; i++) {
		ret = REG_READ(REG_PORT(i), 0x04);
		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
	}

	msleep(2);

	REG_WRITE(REG_GLOBAL, 0x04, 0xc400);

	for (i = 0; i < 1000; i++) {
		ret = REG_READ(REG_GLOBAL, 0x00);
		if ((ret & 0xc800) == 0xc800)
			break;

		msleep(1);
	}
	if (i == 1000)
		return -ETIMEDOUT;

	return 0;
}

开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:26，代码来源:mv88e6123_61_65.c

示例3: mv88e6060_switch_reset

static int mv88e6060_switch_reset(struct dsa_switch *ds)
{
	int i;
	int ret;
	unsigned long timeout;

	/* Set all ports to the disabled state. */
	for (i = 0; i < 6; i++) {
		ret = REG_READ(REG_PORT(i), 0x04);
		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
	}

	/* Wait for transmit queues to drain. */
	usleep_range(2000, 4000);

	/* Reset the switch. */
	REG_WRITE(REG_GLOBAL, 0x0a, 0xa130);

	/* Wait up to one second for reset to complete. */
	timeout = jiffies + 1 * HZ;
	while (time_before(jiffies, timeout)) {
		ret = REG_READ(REG_GLOBAL, 0x00);
		if ((ret & 0x8000) == 0x0000)
			break;

		usleep_range(1000, 2000);
	}
	if (time_after(jiffies, timeout))
		return -ETIMEDOUT;

	return 0;
}

开发者ID:Ambrosia，项目名称:whatever，代码行数:32，代码来源:mv88e6060.c

示例4: dsa_host_dev_to_mii_bus

static char *mv88e6063_probe(struct mii_bus *bus, int sw_addr)
{
#else
static char *mv88e6063_probe(struct device *host_dev, int sw_addr)
{
	struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
#endif
	int ret;

	ret = mdiobus_read(bus, REG_PORT(0), 0x03);
	if (ret >= 0) {
		ret &= 0xfff0;
		if (ret == 0x1530)
			return "Marvell 88E6063";
	}

	return NULL;
}

static int mv88e6063_switch_reset(struct dsa_switch *ds)
{
	int i;
	int ret;

	/*
	 * Set all ports to the disabled state.
	 */
	for (i = 0; i < NUM_PORTS; i++) {
		ret = REG_READ(REG_PORT(i), 0x04);
		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
	}

	/*
	 * Wait for transmit queues to drain.
	 */
	msleep(2);

	/*
	 * Reset the switch.
	 */
	REG_WRITE(REG_GLOBAL, 0x0a, 0xa130);

	/*
	 * Wait up to one second for reset to complete.
	 */
	for (i = 0; i < 1000; i++) {
		ret = REG_READ(REG_GLOBAL, 0x00);
		if ((ret & 0x8000) == 0x0000)
			break;

		msleep(1);
	}
	if (i == 1000)
		return -ETIMEDOUT;

	return 0;
}

开发者ID:020gzh，项目名称:openwrt-mirror，代码行数:57，代码来源:mv88e6063.c

示例5: _Lcd_Write_Data

VOID _Lcd_Write_Data( UCHAR data_4bit )
{
	if( data_4bit & 1 ) {
		sbi( REG_PORT(D_LCD_D4_PORT_NAME), BIT_PORT(D_LCD_D4_PORT_NAME, D_LCD_D4_BIT) );
	}
	else {
		cbi( REG_PORT(D_LCD_D4_PORT_NAME), BIT_PORT(D_LCD_D4_PORT_NAME, D_LCD_D4_BIT) );
	}
	data_4bit >>= 1;

	if( data_4bit & 1 ) {
		sbi( REG_PORT(D_LCD_D5_PORT_NAME), BIT_PORT(D_LCD_D5_PORT_NAME, D_LCD_D5_BIT) );
	}
	else {
		cbi( REG_PORT(D_LCD_D5_PORT_NAME), BIT_PORT(D_LCD_D5_PORT_NAME, D_LCD_D5_BIT) );
	}
	data_4bit >>= 1;

	if( data_4bit & 1 ) {
		sbi( REG_PORT(D_LCD_D6_PORT_NAME), BIT_PORT(D_LCD_D6_PORT_NAME, D_LCD_D6_BIT) );
	}
	else {
		cbi( REG_PORT(D_LCD_D6_PORT_NAME), BIT_PORT(D_LCD_D6_PORT_NAME, D_LCD_D6_BIT) );
	}
	data_4bit >>= 1;

	if( data_4bit & 1 ) {
		sbi( REG_PORT(D_LCD_D7_PORT_NAME), BIT_PORT(D_LCD_D7_PORT_NAME, D_LCD_D7_BIT) );
	}
	else {
		cbi( REG_PORT(D_LCD_D7_PORT_NAME), BIT_PORT(D_LCD_D7_PORT_NAME, D_LCD_D7_BIT) );
	}
}

开发者ID:samy-gh，项目名称:avr_proj，代码行数:33，代码来源:lcd_write_data.c

示例6: _mv88e6xxx_get_ethtool_stats

static void _mv88e6xxx_get_ethtool_stats(struct dsa_switch *ds,
					 int nr_stats,
					 struct mv88e6xxx_hw_stat *stats,
					 int port, uint64_t *data)
{
	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
	int ret;
	int i;

	mutex_lock(&ps->stats_mutex);

	ret = mv88e6xxx_stats_snapshot(ds, port);
	if (ret < 0) {
		mutex_unlock(&ps->stats_mutex);
		return;
	}

	/* Read each of the counters. */
	for (i = 0; i < nr_stats; i++) {
		struct mv88e6xxx_hw_stat *s = stats + i;
		u32 low;
		u32 high = 0;

		if (s->reg >= 0x100) {
			int ret;

			ret = mv88e6xxx_reg_read(ds, REG_PORT(port),
						 s->reg - 0x100);
			if (ret < 0)
				goto error;
			low = ret;
			if (s->sizeof_stat == 4) {
				ret = mv88e6xxx_reg_read(ds, REG_PORT(port),
							 s->reg - 0x100 + 1);
				if (ret < 0)
					goto error;
				high = ret;
			}
			data[i] = (((u64)high) << 16) | low;
			continue;
		}
		mv88e6xxx_stats_read(ds, s->reg, &low);
		if (s->sizeof_stat == 8)
			mv88e6xxx_stats_read(ds, s->reg + 1, &high);

		data[i] = (((u64)high) << 32) | low;
	}
error:
	mutex_unlock(&ps->stats_mutex);
}

开发者ID:RealJohnGalt，项目名称:linux，代码行数:50，代码来源:mv88e6xxx.c

示例7: dsa_host_dev_to_mii_bus

static char *mv88e6123_61_65_probe(struct device *host_dev, int sw_addr)
{
	struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
	int ret;

	if (bus == NULL)
		return NULL;

	ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), PORT_SWITCH_ID);
	if (ret >= 0) {
		if (ret == PORT_SWITCH_ID_6123_A1)
			return "Marvell 88E6123 (A1)";
		if (ret == PORT_SWITCH_ID_6123_A2)
			return "Marvell 88E6123 (A2)";
		if ((ret & 0xfff0) == PORT_SWITCH_ID_6123)
			return "Marvell 88E6123";

		if (ret == PORT_SWITCH_ID_6161_A1)
			return "Marvell 88E6161 (A1)";
		if (ret == PORT_SWITCH_ID_6161_A2)
			return "Marvell 88E6161 (A2)";
		if ((ret & 0xfff0) == PORT_SWITCH_ID_6161)
			return "Marvell 88E6161";

		if (ret == PORT_SWITCH_ID_6165_A1)
			return "Marvell 88E6165 (A1)";
		if (ret == PORT_SWITCH_ID_6165_A2)
			return "Marvell 88e6165 (A2)";
		if ((ret & 0xfff0) == PORT_SWITCH_ID_6165)
			return "Marvell 88E6165";
	}

	return NULL;
}

开发者ID:19Dan01，项目名称:linux，代码行数:34，代码来源:mv88e6123_61_65.c

示例8: mv88e6xxx_poll_link

void mv88e6xxx_poll_link(struct dsa_switch *ds)
{
	int i;

	for (i = 0; i < DSA_MAX_PORTS; i++) {
		struct net_device *dev;
		int uninitialized_var(port_status);
		int link;
		int speed;
		int duplex;
		int fc;

		dev = ds->ports[i];
		if (dev == NULL)
			continue;

		link = 0;
		if (dev->flags & IFF_UP) {
			port_status = mv88e6xxx_reg_read(ds, REG_PORT(i), 0x00);
			if (port_status < 0)
				continue;

			link = !!(port_status & 0x0800);
		}

		if (!link) {
			if (netif_carrier_ok(dev)) {
				netdev_info(dev, "link down\n");
				netif_carrier_off(dev);
			}
			continue;
		}

		switch (port_status & 0x0300) {
		case 0x0000:
			speed = 10;
			break;
		case 0x0100:
			speed = 100;
			break;
		case 0x0200:
			speed = 1000;
			break;
		default:
			speed = -1;
			break;
		}
		duplex = (port_status & 0x0400) ? 1 : 0;
		fc = (port_status & 0x8000) ? 1 : 0;

		if (!netif_carrier_ok(dev)) {
			netdev_info(dev,
				    "link up, %d Mb/s, %s duplex, flow control %sabled\n",
				    speed,
				    duplex ? "full" : "half",
				    fc ? "en" : "dis");
			netif_carrier_on(dev);
		}
	}
}

开发者ID:3null，项目名称:linux，代码行数:60，代码来源:mv88e6xxx.c

示例9: Lcd_Control

/*--------------------------------------------------
 *  LCD & Cursor control (Blinking, ON/OFF,...)
 *--------------------------------------------------*/
VOID Lcd_Control( const UCHAR disonoff, const UCHAR curonoff, const UCHAR curblink )
{
	UCHAR	data;
	// DB=0000_1xxx, RS=0, RW=0

	if( !LCD_IS_OPEN() ) {
		return;
	}

	cbi( REG_PORT(D_LCD_RS_PORT_NAME), BIT_PORT(D_LCD_RS_PORT_NAME, D_LCD_RS_BIT) );
	// 1st
	_Lcd_Write_Data( 0 );	// Hi
	_Lcd_ToggleE();
	// 2nd
	data = 0x8;
	if( disonoff == 1 ) {
		data |= 0x04;	//	1:表示on     / 0:表示off
	}
	if( curonoff == 1 ) {
		data |= 0x02;	//	1:カーソルon / 0:カーソルoff
	}
	if( curblink == 1 ) {
		data |= 0x01;	//	1:ブリンクon / 0:ブリンクoff
	}
	_Lcd_Write_Data( data );
	_Lcd_ToggleE();
	_delay_us( LCD_WAIT_FACTOR(40) );	//wait 40us
}

开发者ID:samy-gh，项目名称:avr_proj，代码行数:31，代码来源:lcd_control.c

示例10: mv88e6131_setup

static int mv88e6131_setup(struct dsa_switch *ds)
{
	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
	int i;
	int ret;

	mutex_init(&ps->smi_mutex);
	mv88e6xxx_ppu_state_init(ds);
	mutex_init(&ps->stats_mutex);

	ps->id = REG_READ(REG_PORT(0), 0x03) & 0xfff0;

	ret = mv88e6131_switch_reset(ds);
	if (ret < 0)
		return ret;

	/* @@@ initialise vtu and atu */

	ret = mv88e6131_setup_global(ds);
	if (ret < 0)
		return ret;

	for (i = 0; i < 11; i++) {
		ret = mv88e6131_setup_port(ds, i);
		if (ret < 0)
			return ret;
	}

	return 0;
}

开发者ID:3null，项目名称:linux，代码行数:30，代码来源:mv88e6131.c

示例11: __mv88e6xxx_reg_read

static char *mv88e6123_61_65_probe(struct mii_bus *bus, int sw_addr)
{
	int ret;

	ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
	if (ret >= 0) {
		if (ret == 0x1212)
			return "Marvell 88E6123 (A1)";
		if (ret == 0x1213)
			return "Marvell 88E6123 (A2)";
		if ((ret & 0xfff0) == 0x1210)
			return "Marvell 88E6123";

		if (ret == 0x1612)
			return "Marvell 88E6161 (A1)";
		if (ret == 0x1613)
			return "Marvell 88E6161 (A2)";
		if ((ret & 0xfff0) == 0x1610)
			return "Marvell 88E6161";

		if (ret == 0x1652)
			return "Marvell 88E6165 (A1)";
		if (ret == 0x1653)
			return "Marvell 88e6165 (A2)";
		if ((ret & 0xfff0) == 0x1650)
			return "Marvell 88E6165";
	}

	return NULL;
}

开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:30，代码来源:mv88e6123_61_65.c

示例12: mv88e6060_setup_port

static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
{
	int addr = REG_PORT(p);

	/* Do not force flow control, disable Ingress and Egress
	 * Header tagging, disable VLAN tunneling, and set the port
	 * state to Forwarding.  Additionally, if this is the CPU
	 * port, enable Ingress and Egress Trailer tagging mode.
	 */
	REG_WRITE(addr, 0x04, dsa_is_cpu_port(ds, p) ?  0x4103 : 0x0003);

	/* Port based VLAN map: give each port its own address
	 * database, allow the CPU port to talk to each of the 'real'
	 * ports, and allow each of the 'real' ports to only talk to
	 * the CPU port.
	 */
	REG_WRITE(addr, 0x06,
			((p & 0xf) << 12) |
			 (dsa_is_cpu_port(ds, p) ?
				ds->phys_port_mask :
				(1 << ds->dst->cpu_port)));

	/* Port Association Vector: when learning source addresses
	 * of packets, add the address to the address database using
	 * a port bitmap that has only the bit for this port set and
	 * the other bits clear.
	 */
	REG_WRITE(addr, 0x0b, 1 << p);

	return 0;
}

开发者ID:Ambrosia，项目名称:whatever，代码行数:31，代码来源:mv88e6060.c

示例13: mv88e6xxx_get_eee

int mv88e6xxx_get_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e)
{
	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
	int reg;

	mutex_lock(&ps->phy_mutex);

	reg = _mv88e6xxx_phy_read_indirect(ds, port, 16);
	if (reg < 0)
		goto out;

	e->eee_enabled = !!(reg & 0x0200);
	e->tx_lpi_enabled = !!(reg & 0x0100);

	reg = mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_STATUS);
	if (reg < 0)
		goto out;

	e->eee_active = !!(reg & PORT_STATUS_EEE);
	reg = 0;

out:
	mutex_unlock(&ps->phy_mutex);
	return reg;
}

开发者ID:RealJohnGalt，项目名称:linux，代码行数:25，代码来源:mv88e6xxx.c

示例14: mv88e6060_setup_port

static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
{
	int addr = REG_PORT(p);

	/* Do not force flow control, disable Ingress and Egress
	 * Header tagging, disable VLAN tunneling, and set the port
	 * state to Forwarding.  Additionally, if this is the CPU
	 * port, enable Ingress and Egress Trailer tagging mode.
	 */
	REG_WRITE(addr, PORT_CONTROL,
		  dsa_is_cpu_port(ds, p) ?
			PORT_CONTROL_TRAILER |
			PORT_CONTROL_INGRESS_MODE |
			PORT_CONTROL_STATE_FORWARDING :
			PORT_CONTROL_STATE_FORWARDING);

	/* Port based VLAN map: give each port its own address
	 * database, allow the CPU port to talk to each of the 'real'
	 * ports, and allow each of the 'real' ports to only talk to
	 * the CPU port.
	 */
	REG_WRITE(addr, PORT_VLAN_MAP,
		  ((p & 0xf) << PORT_VLAN_MAP_DBNUM_SHIFT) |
		   (dsa_is_cpu_port(ds, p) ? dsa_user_ports(ds) :
		    BIT(dsa_to_port(ds, p)->cpu_dp->index)));

	/* Port Association Vector: when learning source addresses
	 * of packets, add the address to the address database using
	 * a port bitmap that has only the bit for this port set and
	 * the other bits clear.
	 */
	REG_WRITE(addr, PORT_ASSOC_VECTOR, BIT(p));

	return 0;
}

开发者ID:Lyude，项目名称:linux，代码行数:35，代码来源:mv88e6060.c

示例15: mv88e6131_setup_port

static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
{
	struct mv88e6xxx_priv_state *ps = (void *)(ds + 1);
	int addr = REG_PORT(p);
	u16 val;

	if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
		if (ps->id == ID_6085)
			REG_WRITE(addr, 0x01, 0x003d); 
		else
			REG_WRITE(addr, 0x01, 0x003e); 
	else
		REG_WRITE(addr, 0x01, 0x0003);

	val = 0x0433;
	if (p == dsa_upstream_port(ds)) {
		val |= 0x0104;
		if (ps->id == ID_6085)
			val |= 0x0008;
	}
	if (ds->dsa_port_mask & (1 << p))
		val |= 0x0100;
	REG_WRITE(addr, 0x04, val);

	REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000);

	val = (p & 0xf) << 12;
	if (dsa_is_cpu_port(ds, p))
		val |= ds->phys_port_mask;
	else
		val |= 1 << dsa_upstream_port(ds);
	REG_WRITE(addr, 0x06, val);

	REG_WRITE(addr, 0x07, 0x0000);

	if (ps->id == ID_6085)
		REG_WRITE(addr, 0x08, 0x0080);
	else {
		val = 0x0080 | dsa_upstream_port(ds);
		if (p == dsa_upstream_port(ds))
			val |= 0x0040;
		REG_WRITE(addr, 0x08, val);
	}

	REG_WRITE(addr, 0x09, 0x0000);

	REG_WRITE(addr, 0x0a, 0x0000);

	REG_WRITE(addr, 0x0b, 1 << p);

	REG_WRITE(addr, 0x18, 0x3210);

	REG_WRITE(addr, 0x19, 0x7654);

	return 0;
}

开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:56，代码来源:mv88e6131.c

示例16: mv88e6123_61_65_setup_port

static int mv88e6123_61_65_setup_port(struct dsa_switch *ds, int p)
{
	int addr = REG_PORT(p);
	u16 val;

	if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
		REG_WRITE(addr, 0x01, 0x003e);
	else
		REG_WRITE(addr, 0x01, 0x0003);

	REG_WRITE(addr, 0x02, 0x0000);

	val = 0x0433;
	if (dsa_is_cpu_port(ds, p)) {
		if (ds->dst->tag_protocol == htons(ETH_P_EDSA))
			val |= 0x3300;
		else
			val |= 0x0100;
	}
	if (ds->dsa_port_mask & (1 << p))
		val |= 0x0100;
	if (p == dsa_upstream_port(ds))
		val |= 0x000c;
	REG_WRITE(addr, 0x04, val);

	REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000);

	val = (p & 0xf) << 12;
	if (dsa_is_cpu_port(ds, p))
		val |= ds->phys_port_mask;
	else
		val |= 1 << dsa_upstream_port(ds);
	REG_WRITE(addr, 0x06, val);

	REG_WRITE(addr, 0x07, 0x0000);

	REG_WRITE(addr, 0x08, 0x2080);

	REG_WRITE(addr, 0x09, 0x0001);

	REG_WRITE(addr, 0x0a, 0x0000);

	REG_WRITE(addr, 0x0b, 1 << p);

	REG_WRITE(addr, 0x0c, 0x0000);

	REG_WRITE(addr, 0x0d, 0x0000);

	REG_WRITE(addr, 0x0f, ETH_P_EDSA);

	REG_WRITE(addr, 0x18, 0x3210);

	REG_WRITE(addr, 0x19, 0x7654);

	return 0;
}

开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:56，代码来源:mv88e6123_61_65.c

示例17: mv88e6020_switch_reset

/* Cleared for 6020 */
static int mv88e6020_switch_reset(struct dsa_switch *ds)
{
	int i;
	int ret;

	/*
	 * Set all ports to the disabled state.
	 */
	for (i = 0; i < 7; i++) {
		ret = REG_READ(REG_PORT(i), 0x04);
		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
	}

	/*
	 * Wait for transmit queues to drain.
	 */
	msleep(2);

	/*
	 * Reset the switch.
	 */
	//Set per the original mv88e6060 code
	REG_WRITE(REG_GLOBAL1, 0x0a, 0x2130);
	//Sets reset, this also disables all interrupts, might not be wise
	REG_WRITE(REG_GLOBAL1, 0x04, 0x8400);

	/*
	 * Wait up to one second for reset to complete.
	 */
	for (i = 0; i < 1000; i++) {
		ret = REG_READ(REG_GLOBAL1, 0x00);
		//The code originally checked bit15, but the 6060 manual calls this reserved
		//Using bit 11 is a best guess
		if (ret & 0x800)
			break;

		msleep(1);
	}
	if (i == 1000)
		return -ETIMEDOUT;

	return 0;
}

开发者ID:Jonathan727，项目名称:linux-2.6.35.3-imx28，代码行数:44，代码来源:mv88e6020.c

示例18: mdiobus_read

static char *mv88e6060_probe(struct mii_bus *bus, int sw_addr)
{
	int ret;

	ret = mdiobus_read(bus, sw_addr + REG_PORT(0), 0x03);
	if (ret >= 0) {
		ret &= 0xfff0;
		if (ret == 0x0600)
			return "Marvell 88E6060";
	}

	return NULL;
}

开发者ID:CSCLOG，项目名称:beaglebone，代码行数:13，代码来源:mv88e6060.c

示例19: mv88e6xxx_switch_reset

int mv88e6xxx_switch_reset(struct dsa_switch *ds, bool ppu_active)
{
	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
	u16 is_reset = (ppu_active ? 0x8800 : 0xc800);
	unsigned long timeout;
	int ret;
	int i;

	/* Set all ports to the disabled state. */
	for (i = 0; i < ps->num_ports; i++) {
		ret = REG_READ(REG_PORT(i), PORT_CONTROL);
		REG_WRITE(REG_PORT(i), PORT_CONTROL, ret & 0xfffc);
	}

	/* Wait for transmit queues to drain. */
	usleep_range(2000, 4000);

	/* Reset the switch. Keep the PPU active if requested. The PPU
	 * needs to be active to support indirect phy register access
	 * through global registers 0x18 and 0x19.
	 */
	if (ppu_active)
		REG_WRITE(REG_GLOBAL, 0x04, 0xc000);
	else
		REG_WRITE(REG_GLOBAL, 0x04, 0xc400);

	/* Wait up to one second for reset to complete. */
	timeout = jiffies + 1 * HZ;
	while (time_before(jiffies, timeout)) {
		ret = REG_READ(REG_GLOBAL, 0x00);
		if ((ret & is_reset) == is_reset)
			break;
		usleep_range(1000, 2000);
	}
	if (time_after(jiffies, timeout))
		return -ETIMEDOUT;

	return 0;
}

开发者ID:RealJohnGalt，项目名称:linux，代码行数:39，代码来源:mv88e6xxx.c

示例20: mv88e6xxx_setup_port_common

int mv88e6xxx_setup_port_common(struct dsa_switch *ds, int port)
{
	struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
	int ret, fid;

	mutex_lock(&ps->smi_mutex);

	/* Port Control 1: disable trunking, disable sending
	 * learning messages to this port.
	 */
	ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), PORT_DEFAULT_VLAN,
				   0x0000);
	if (ret)
		goto abort;

	/* Port based VLAN map: give each port its own address
	 * database, allow the CPU port to talk to each of the 'real'
	 * ports, and allow each of the 'real' ports to only talk to
	 * the upstream port.
	 */
	fid = __ffs(ps->fid_mask);
	ps->fid[port] = fid;
	ps->fid_mask &= ~(1 << fid);

	if (!dsa_is_cpu_port(ds, port))
		ps->bridge_mask[fid] = 1 << port;

	ret = _mv88e6xxx_update_port_config(ds, port);
	if (ret)
		goto abort;

	/* Default VLAN ID and priority: don't set a default VLAN
	 * ID, and set the default packet priority to zero.
	 */
	ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), 0x07, 0x0000);
abort:
	mutex_unlock(&ps->smi_mutex);
	return ret;
}

开发者ID:RealJohnGalt，项目名称:linux，代码行数:39，代码来源:mv88e6xxx.c

注：本文中的REG_PORT函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ REG_RD函数代码示例发布时间：2022-05-30

C++ REG_P函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19286|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：10021|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8344|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8713|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8658|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9688|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8647|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8014|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8683|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7550|2022-11-06

客服电话

电子邮件

C++ REG_PORT函数代码示例

示例1: mv88e6xxx_set_port_state

示例2: mv88e6123_61_65_switch_reset

示例3: mv88e6060_switch_reset

示例4: dsa_host_dev_to_mii_bus

示例5: _Lcd_Write_Data

示例6: _mv88e6xxx_get_ethtool_stats

示例7: dsa_host_dev_to_mii_bus

示例8: mv88e6xxx_poll_link

示例9: Lcd_Control

示例10: mv88e6131_setup

示例11: __mv88e6xxx_reg_read

示例12: mv88e6060_setup_port

示例13: mv88e6xxx_get_eee

示例14: mv88e6060_setup_port

示例15: mv88e6131_setup_port

示例16: mv88e6123_61_65_setup_port

示例17: mv88e6020_switch_reset

示例18: mdiobus_read

示例19: mv88e6xxx_switch_reset

示例20: mv88e6xxx_setup_port_common

请发表评论

全部评论

上一篇：

下一篇：

配置Delphi工具菜单转

krishnaik06/Machine-Learning-in-90-days

armancodv/building-energy-model-matlab:

美元符号为什么是“$”

FGRibreau/import-tweets-to-mastodon: How

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053