C++ RCC_AHBPeriphClockCmd函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中RCC_AHBPeriphClockCmd函数的典型用法代码示例。如果您正苦于以下问题：C++ RCC_AHBPeriphClockCmd函数的具体用法？C++ RCC_AHBPeriphClockCmd怎么用？C++ RCC_AHBPeriphClockCmd使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了RCC_AHBPeriphClockCmd函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: ADC_Config

/**
  * @brief  ADC1 channel configuration
  * @param  None
  * @retval None
  */
static void ADC_Config(void)
{
  ADC_InitTypeDef     ADC_InitStructure;
  GPIO_InitTypeDef    GPIO_InitStructure;
  NVIC_InitTypeDef    NVIC_InitStructure;
    
  /* GPIOC Periph clock enable */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC, ENABLE);
  
  /* ADC1 Periph clock enable */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
  
  /* Configure ADC Channel11 as analog input */
#ifdef USE_STM320518_EVAL
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 ;
#elif defined (USE_STM32072B_EVAL)
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 ;
#endif /* USE_STM320518_EVAL */
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
  GPIO_Init(GPIOC, &GPIO_InitStructure);
  
  /* ADC1 DeInit */  
  ADC_DeInit(ADC1);
  
  /* Initialize ADC structure */
  ADC_StructInit(&ADC_InitStructure);
  
  /* Configure the ADC1 in continuous mode withe a resolution equal to 12 bits  */
  ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE; 
  ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_ScanDirection = ADC_ScanDirection_Upward;
  ADC_Init(ADC1, &ADC_InitStructure);
  
  /* Convert the ADC1 Channel11 and channel10 with 239.5 Cycles as sampling time */ 
#ifdef USE_STM320518_EVAL
  ADC_ChannelConfig(ADC1, ADC_Channel_11 , ADC_SampleTime_239_5Cycles);
#elif defined (USE_STM32072B_EVAL)
  ADC_ChannelConfig(ADC1, ADC_Channel_10 , ADC_SampleTime_239_5Cycles);
#endif /* USE_STM320518_EVAL */
  
  /* Analog watchdog config ******************************************/
  /* Configure the ADC Thresholds between 1.5V and 2.5V (1861, 3102) */
  ADC_AnalogWatchdogThresholdsConfig(ADC1, 3102, 1861);

  /* Enable the ADC1 single channel  */
  ADC_AnalogWatchdogSingleChannelCmd(ADC1, ENABLE);
  
  ADC_OverrunModeCmd(ADC1, ENABLE);
  /* Enable the ADC1 analog watchdog */
  ADC_AnalogWatchdogCmd(ADC1,ENABLE);
  
      /* Select a single ADC1 channel 11 */
#ifdef USE_STM320518_EVAL
  ADC_AnalogWatchdogSingleChannelConfig(ADC1, ADC_AnalogWatchdog_Channel_11);
#elif defined (USE_STM32072B_EVAL)
  ADC_AnalogWatchdogSingleChannelConfig(ADC1, ADC_AnalogWatchdog_Channel_10);
#endif /* USE_STM320518_EVAL */
   
  /* Enable AWD interrupt */
  ADC_ITConfig(ADC1, ADC_IT_AWD, ENABLE);
  
  /* Configure and enable ADC1 interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = ADC1_COMP_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
  
  /* Enable the ADC1 Calibration */
  ADC_GetCalibrationFactor(ADC1);
  
  /* Enable the ADC peripheral */
  ADC_Cmd(ADC1, ENABLE);     
  
  /* Wait the ADRDY flag */
  while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_ADRDY)); 
  
  /* ADC1 regular Software Start Conv */ 
  ADC_StartOfConversion(ADC1);
}

开发者ID:Azizou，项目名称:stm32f0_devel，代码行数:87，代码来源:main.c

示例2: TIM_Config

/**
  * @brief  Configure the TIM3 pins.
  * @param  None
  * @retval None
  */
static void TIM_Config(void)
{
  TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
  TIM_OCInitTypeDef  TIM_OCInitStructure;
  GPIO_InitTypeDef GPIO_InitStructure;

  /* TIM3 clock enable */
  RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);

  /* GPIOC clock enable */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB, ENABLE);
   
  /* GPIOA Configuration: TIM3 CH1 (PA6) and TIM3 CH2 (PA7) */
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
  GPIO_Init(GPIOA, &GPIO_InitStructure); 

  /* GPIOB Configuration: TIM3 CH3 (PB0) and TIM3 CH4 (PB1) */
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1;
  GPIO_Init(GPIOB, &GPIO_InitStructure);
    
  /* Connect TIM Channels to AF2 */
  GPIO_PinAFConfig(GPIOA, GPIO_PinSource6, GPIO_AF_1);
  GPIO_PinAFConfig(GPIOA, GPIO_PinSource7, GPIO_AF_1); 
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource0, GPIO_AF_1);
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource1, GPIO_AF_1);

  /* Initialize Leds mounted on STM320518-EVAL board */
  STM_EVAL_LEDInit(LED1);  
  
  TIM_TimeBaseStructInit(&TIM_TimeBaseStructure);

  TIM_OCStructInit(&TIM_OCInitStructure);

  /* ---------------------------------------------------------------------------
    TIM3 Configuration: Output Compare Active Mode:
    In this example TIM3 input clock (TIM3CLK) is set to APB1 clock (PCLK1)    
      TIM3CLK = PCLK1  
      PCLK1 = HCLK 
      => TIM3CLK = HCLK = SystemCoreClock 
          
    To get TIM3 counter clock at 1 KHz, the prescaler is computed as follows:
       Prescaler = (TIM3CLK / TIM3 counter clock) - 1
       Prescaler = (SystemCoreClock /1 KHz) - 1
       
    Generate 4 signals with 4 different delays:
    TIM3_CH1 delay = CCR1_Val/TIM3 counter clock = 1000 ms
    TIM3_CH2 delay = CCR2_Val/TIM3 counter clock = 500 ms
    TIM3_CH3 delay = CCR3_Val/TIM3 counter clock = 250 ms
    TIM3_CH4 delay = CCR4_Val/TIM3 counter clock = 125 ms

    Note: 
     SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f0xx.c file.
     Each time the core clock (HCLK) changes, user had to call SystemCoreClockUpdate()
     function to update SystemCoreClock variable value. Otherwise, any configuration
     based on this variable will be incorrect. 
     
  --------------------------------------------------------------------------- */
  
  /*Compute the prescaler value */
  PrescalerValue = (uint16_t) (SystemCoreClock / 1000) - 1;

  /* Time base configuration */
  TIM_TimeBaseStructure.TIM_Period = 65535;
  TIM_TimeBaseStructure.TIM_Prescaler = PrescalerValue;
  TIM_TimeBaseStructure.TIM_ClockDivision = 0;
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;

  TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);

  /* Output Compare Active Mode configuration: Channel1 */
  TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_Active;
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
  TIM_OCInitStructure.TIM_Pulse = CCR1_Val;
  TIM_OC1Init(TIM3, &TIM_OCInitStructure);

  TIM_OC1PreloadConfig(TIM3, TIM_OCPreload_Disable);
  TIM_ARRPreloadConfig(TIM3, DISABLE); 
  /* Output Compare Active Mode configuration: Channel2 */
  TIM_OCInitStructure.TIM_Pulse = CCR2_Val;
  TIM_OC2Init(TIM3, &TIM_OCInitStructure);

  TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Disable);

  /* Output Compare Active Mode configuration: Channel3 */
  TIM_OCInitStructure.TIM_Pulse = CCR3_Val;
  TIM_OC3Init(TIM3, &TIM_OCInitStructure);

  TIM_OC3PreloadConfig(TIM3, TIM_OCPreload_Disable);

  /* Output Compare Active Mode configuration: Channel4 */
//.........这里部分代码省略.........

开发者ID:Lee-Kevin，项目名称:MotorBridgeCapeFirmwareSourceCode，代码行数:101，代码来源:main.c

示例3: adcInit

void adcInit(drv_adc_config_t *init)
{
    ADC_InitTypeDef ADC_InitStructure;
    DMA_InitTypeDef DMA_InitStructure;
    GPIO_InitTypeDef GPIO_InitStructure;

    uint8_t i;
    uint8_t adcChannelCount = 0;

    memset(&adcConfig, 0, sizeof(adcConfig));

    GPIO_StructInit(&GPIO_InitStructure);
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_0 | GPIO_Pin_3;
    GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_AN;
    GPIO_InitStructure.GPIO_PuPd  = GPIO_PuPd_NOPULL ;

    adcConfig[ADC_BATTERY].adcChannel = ADC_Channel_6;
    adcConfig[ADC_BATTERY].dmaIndex = adcChannelCount;
    adcConfig[ADC_BATTERY].sampleTime = ADC_SampleTime_601Cycles5;
    adcConfig[ADC_BATTERY].enabled = true;
    adcChannelCount++;

    if (init->enableCurrentMeter) {
        GPIO_InitStructure.GPIO_Pin |= GPIO_Pin_1;

        adcConfig[ADC_CURRENT].adcChannel = ADC_Channel_7;
        adcConfig[ADC_CURRENT].dmaIndex = adcChannelCount;
        adcConfig[ADC_CURRENT].sampleTime = ADC_SampleTime_601Cycles5;
        adcConfig[ADC_CURRENT].enabled = true;
        adcChannelCount++;

    }

    if (init->enableRSSI) {
        GPIO_InitStructure.GPIO_Pin |= GPIO_Pin_2;

		adcConfig[ADC_RSSI].adcChannel = ADC_Channel_8;
		adcConfig[ADC_RSSI].dmaIndex = adcChannelCount;
		adcConfig[ADC_RSSI].sampleTime = ADC_SampleTime_601Cycles5;
		adcConfig[ADC_RSSI].enabled = true;
		adcChannelCount++;
    }

    adcConfig[ADC_EXTERNAL1].adcChannel = ADC_Channel_9;
    adcConfig[ADC_EXTERNAL1].dmaIndex = adcChannelCount;
    adcConfig[ADC_EXTERNAL1].sampleTime = ADC_SampleTime_601Cycles5;
    adcConfig[ADC_EXTERNAL1].enabled = true;
    adcChannelCount++;

    RCC_ADCCLKConfig(RCC_ADC12PLLCLK_Div256);  // 72 MHz divided by 256 = 281.25 kHz
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1 | RCC_AHBPeriph_ADC12, ENABLE);

    DMA_DeInit(DMA1_Channel1);

    DMA_StructInit(&DMA_InitStructure);
    DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)&ADC1->DR;
    DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)adcValues;
    DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
    DMA_InitStructure.DMA_BufferSize = adcChannelCount;
    DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
    DMA_InitStructure.DMA_MemoryInc = adcChannelCount > 1 ? DMA_MemoryInc_Enable : DMA_MemoryInc_Disable;
    DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
    DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
    DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
    DMA_InitStructure.DMA_Priority = DMA_Priority_High;
    DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;

    DMA_Init(DMA1_Channel1, &DMA_InitStructure);

    DMA_Cmd(DMA1_Channel1, ENABLE);

    GPIO_Init(GPIOC, &GPIO_InitStructure);

    // calibrate

    ADC_VoltageRegulatorCmd(ADC1, ENABLE);
    delay(10);
    ADC_SelectCalibrationMode(ADC1, ADC_CalibrationMode_Single);
    ADC_StartCalibration(ADC1);
    while(ADC_GetCalibrationStatus(ADC1) != RESET);
    ADC_VoltageRegulatorCmd(ADC1, DISABLE);


    ADC_CommonInitTypeDef ADC_CommonInitStructure;

    ADC_CommonStructInit(&ADC_CommonInitStructure);
    ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStructure.ADC_Clock = ADC_Clock_SynClkModeDiv4;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_1;
    ADC_CommonInitStructure.ADC_DMAMode = ADC_DMAMode_Circular;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = 0;
    ADC_CommonInit(ADC1, &ADC_CommonInitStructure);

    ADC_StructInit(&ADC_InitStructure);

    ADC_InitStructure.ADC_ContinuousConvMode    = ADC_ContinuousConvMode_Enable;
    ADC_InitStructure.ADC_Resolution            = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ExternalTrigConvEvent = ADC_ExternalTrigConvEvent_0;
    ADC_InitStructure.ADC_ExternalTrigEventEdge = ADC_ExternalTrigEventEdge_None;
    ADC_InitStructure.ADC_DataAlign             = ADC_DataAlign_Right;
//.........这里部分代码省略.........

开发者ID:AhLeeYong，项目名称:cleanflight，代码行数:101，代码来源:adc_stm32f30x.c

示例4: TIM_Config

/**
  * @brief  Configure the TIM3 Pins.
  * @param  None
  * @retval None
  */
static void TIM_Config(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;
    TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
    TIM_OCInitTypeDef  TIM_OCInitStructure;
    uint16_t PrescalerValue = 0;

    /* TIM3 clock enable */
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);

    /* GPIOA and GPIOB clock enable */
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB, ENABLE);

    /* GPIOA Configuration: TIM3 CH1 (PA6) and TIM3 CH2 (PA7) */
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP ;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    /* GPIOB Configuration: TIM3 CH2 (PB0) and TIM3 CH4 (PB7) */
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_7;
    GPIO_Init(GPIOB, &GPIO_InitStructure);

    /* Connect TIM Channels to AF */
    GPIO_PinAFConfig(GPIOA, GPIO_PinSource6, GPIO_AF_2);
    GPIO_PinAFConfig(GPIOA, GPIO_PinSource7, GPIO_AF_2);
    GPIO_PinAFConfig(GPIOB, GPIO_PinSource0, GPIO_AF_2);
    GPIO_PinAFConfig(GPIOB, GPIO_PinSource7, GPIO_AF_10);

    /* Enable the TIM3 global Interrupt */
    NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    /* ---------------------------------------------------------------------------
    TIM3 Configuration: Output Compare Toggle Mode:

    In this example TIM3 input clock (TIM3CLK) is set to 2 * APB1 clock (PCLK1),
    since APB1 prescaler is different from 1.
      TIM3CLK = 2 * PCLK1
      PCLK1 = HCLK / 2
      => TIM3CLK = HCLK = SystemCoreClock

     CC1 update rate = TIM3 counter clock / CCR1_Val = 1757.7 Hz
       ==> So the TIM3 Channel 1 generates a periodic signal with a
           frequency equal to 878.8 Hz.

     CC2 update rate = TIM3 counter clock / CCR2_Val = 3515.6 Hz
       ==> So the TIM3 Channel 2 generates a periodic signal with a
           frequency equal to 1757.7 Hz.

     CC3 update rate = TIM3 counter clock / CCR3_Val = 7031.25 Hz
       ==> So the TIM3 Channel 3 generates a periodic signal with a
           frequency equal to 3515.6 Hz.

     CC4 update rate = TIM3 counter clock / CCR4_Val = 14062.5 Hz
       ==> So the TIM3 Channel 4 generates a periodic signal with a
           frequency equal to 7031.25 Hz.

    Note:
     SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f30x.c file.
     Each time the core clock (HCLK) changes, user had to call SystemCoreClockUpdate()
     function to update SystemCoreClock variable value. Otherwise, any configuration
     based on this variable will be incorrect.
    --------------------------------------------------------------------------- */

    /* Time base configuration */
    TIM_TimeBaseStructure.TIM_Period = 65535;
    TIM_TimeBaseStructure.TIM_Prescaler = PrescalerValue;
    TIM_TimeBaseStructure.TIM_ClockDivision = 0;
    TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;

    TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);

    /* Init TIM_OCInitStructure */
    TIM_OCStructInit(&TIM_OCInitStructure);

    /* Output Compare Toggle Mode configuration: Channel1 */
    TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_Toggle;
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = CCR1_Val;
    TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;
    TIM_OC1Init(TIM3, &TIM_OCInitStructure);

    TIM_OC1PreloadConfig(TIM3, TIM_OCPreload_Disable);

    /* Output Compare Toggle Mode configuration: Channel2 */
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = CCR2_Val;

//.........这里部分代码省略.........

开发者ID:coocox，项目名称:Mplib，代码行数:101，代码来源:TIM_OCToggle_Example.c

示例5: init_prog_canal

void init_prog_canal(void)
{
	USART_InitTypeDef USART_InitStructure;
	GPIO_InitTypeDef GPIO_InitStructure;
	NVIC_InitTypeDef NVIC_InitStructure;
	TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;


	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOC, ENABLE);
	RCC_APB1PeriphClockCmd( RCC_APB1Periph_TIM5, ENABLE );
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);

	TIM_DeInit( TIM5 );
	TIM_TimeBaseStructInit( &TIM_TimeBaseStructure );
	TIM_TimeBaseStructure.TIM_Prescaler = 0xFFF;
	TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
	TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
	TIM_TimeBaseStructure.TIM_Period = (unsigned short)0xFFFF;
	TIM_TimeBaseInit( TIM5, &TIM_TimeBaseStructure );
	TIM_ARRPreloadConfig( TIM5, ENABLE );
	TIM_Cmd( TIM5, ENABLE );

	RCC_APB1PeriphClockCmd(RCC_APB1Periph_UART4, ENABLE);
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE);

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_Init(GPIOC, &GPIO_InitStructure);

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
	GPIO_Init(GPIOC, &GPIO_InitStructure);

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
	GPIO_Init(GPIOD, &GPIO_InitStructure);

	switch(_Sys.Can2_Baudrate)
	{
		case 0:USART_InitStructure.USART_BaudRate = 4800;break;
		case 1:USART_InitStructure.USART_BaudRate = 9600;break;
		case 2:USART_InitStructure.USART_BaudRate = 19200;break;
		case 3:USART_InitStructure.USART_BaudRate = 38400;break;
		case 4:USART_InitStructure.USART_BaudRate = 57600;break;
		case 5:USART_InitStructure.USART_BaudRate = 115200;break;
		case 6:USART_InitStructure.USART_BaudRate = 230400;break;
		case 7:USART_InitStructure.USART_BaudRate = 460800;break;
		case 8:USART_InitStructure.USART_BaudRate = 921600;break;
	}
	USART_InitStructure.USART_StopBits = USART_StopBits_1;
	USART_InitStructure.USART_WordLength = USART_WordLength_8b;
	USART_InitStructure.USART_Parity = USART_Parity_No;
	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
	USART_InitStructure.USART_Mode = USART_Mode_Tx | USART_Mode_Rx;
	USART_Init(UART4, &USART_InitStructure);

	NVIC_InitStructure.NVIC_IRQChannel = UART4_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);

	NVIC_InitStructure.NVIC_IRQChannel = DMA2_Channel5_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);

	USART_ITConfig(UART4, USART_IT_RXNE , ENABLE);
	USART_DMACmd(UART4, USART_DMAReq_Tx, ENABLE);
	USART_Cmd(UART4, ENABLE);

	GPIO_WriteBit(GPIOD, GPIO_Pin_7, Bit_RESET);
}

开发者ID:atikbif，项目名称:Relkon6，代码行数:76，代码来源:hcanal.c

示例6: systemInit

void systemInit(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;
#if 0
        gpio_config_t gpio_cfg[] = {
        { LED0_GPIO, LED0_PIN, GPIO_Mode_Out_PP },
        { LED1_GPIO, LED1_PIN, GPIO_Mode_Out_PP },
#ifdef BUZZER
        { BEEP_GPIO, BEEP_PIN, GPIO_Mode_Out_OD },
#endif
    };
    uint8_t gpio_count = sizeof(gpio_cfg) / sizeof(gpio_cfg[0]);
#endif

    // This is needed because some shit inside Keil startup fucks with SystemCoreClock, setting it back to 72MHz even on HSI.
    SystemCoreClockUpdate();

    // Turn on clocks for stuff we use
    RCC_ADCCLKConfig(RCC_PCLK2_Div4);

    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2 | RCC_APB1Periph_TIM3 | RCC_APB1Periph_TIM4 | RCC_APB1Periph_I2C2, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO | RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC | RCC_APB2Periph_TIM1 | RCC_APB2Periph_ADC1 | RCC_APB2Periph_USART1 | RCC_APB2Periph_ADC1 | RCC_APB2Periph_ADC2, ENABLE);
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
    RCC_ClearFlag();

    // Make all GPIO in by default to save power and reduce noise
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
    GPIO_Init(GPIOB, &GPIO_InitStructure);
    GPIO_Init(GPIOC, &GPIO_InitStructure);

    // Turn off JTAG port 'cause we're using the GPIO for leds
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);

#if 0
    // Configure gpio
    for (uint32_t i = 0; i < gpio_count; i++) {
        GPIO_InitStructure.GPIO_Pin = gpio_cfg[i].pin;
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
        GPIO_InitStructure.GPIO_Mode = gpio_cfg[i].mode;
        GPIO_Init(gpio_cfg[i].gpio, &GPIO_InitStructure);
    }

    LED0_OFF;
    LED1_OFF;
    BEEP_OFF;
#endif
    // Init cycle counter
    cycleCounterInit();

    // SysTick
    SysTick_Config(SystemCoreClock / 1000);

    // Configure the rest of the stuff
#if 0
    i2cInit(I2C2);
#endif

    // sleep for 100ms
    delay(100);
}

开发者ID:kh4，项目名称:poweranalyser，代码行数:62，代码来源:drv_system.c

示例7: AdcInit34

static void AdcInit34()
{
	RCC_ADCCLKConfig(RCC_ADC34PLLCLK_Div1);

	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE);
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ADC34, ENABLE);

	NVIC_Configuration34();

	GPIO_InitTypeDef GPIO_InitStructure;
	GPIO_StructInit(&GPIO_InitStructure);

	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 ;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
	GPIO_Init(GPIOB, &GPIO_InitStructure);

	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOE, ENABLE);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_14 ;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
	GPIO_Init(GPIOE, &GPIO_InitStructure);

	ADC_VoltageRegulatorCmd(ADC3, ENABLE);
	ADC_VoltageRegulatorCmd(ADC4, ENABLE);
	delay_us(20);

	ADC_SelectCalibrationMode(ADC3, ADC_CalibrationMode_Single);
	ADC_StartCalibration(ADC3);
	while(ADC_GetCalibrationStatus(ADC3) != RESET );

	ADC_SelectCalibrationMode(ADC4, ADC_CalibrationMode_Single);
	ADC_StartCalibration(ADC4);
	while(ADC_GetCalibrationStatus(ADC4) != RESET );

	ADC_CommonInitTypeDef ADC_CommonInitStructure;
	ADC_CommonInitStructure.ADC_Mode = ADC_Mode_RegSimul;
	//ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
	ADC_CommonInitStructure.ADC_Clock = ADC_Clock_SynClkModeDiv1;
	//ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_1;
	ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
	//ADC_CommonInitStructure.ADC_DMAMode = ADC_DMAMode_OneShot;
	ADC_CommonInitStructure.ADC_DMAMode = ADC_DMAMode_Circular;
	ADC_CommonInitStructure.ADC_TwoSamplingDelay = 0;          
	ADC_CommonInit(ADC3, &ADC_CommonInitStructure);

	ADC_InitTypeDef ADC_InitStructure;

	ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
	if(1)
	{
		ADC_InitStructure.ADC_ContinuousConvMode = ADC_ContinuousConvMode_Disable;
		ADC_InitStructure.ADC_ExternalTrigConvEvent = ADC_ExternalTrigConvEvent_1;
		ADC_InitStructure.ADC_ExternalTrigEventEdge = ADC_ExternalTrigEventEdge_RisingEdge;
	} else
	{
		ADC_InitStructure.ADC_ContinuousConvMode = ADC_ContinuousConvMode_Enable;
		ADC_InitStructure.ADC_ExternalTrigConvEvent = ADC_ExternalTrigConvEvent_0;
		ADC_InitStructure.ADC_ExternalTrigEventEdge = ADC_ExternalTrigEventEdge_None;
	}

	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_OverrunMode = ADC_OverrunMode_Disable;
	//ADC_InitStructure.ADC_OverrunMode = ADC_OverrunMode_Enable;
	ADC_InitStructure.ADC_AutoInjMode = ADC_AutoInjec_Disable;
	ADC_InitStructure.ADC_NbrOfRegChannel = 1;
	ADC_Init(ADC3, &ADC_InitStructure);

	ADC_InitStructure.ADC_ExternalTrigEventEdge = ADC_ExternalTrigEventEdge_None;

	ADC_Init(ADC4, &ADC_InitStructure);

	ADC_DMAConfig(ADC3, ADC_DMAMode_Circular);
	ADC_DMAConfig(ADC4, ADC_DMAMode_Circular);
}

开发者ID:balmerdx，项目名称:rlc-meter-balmer，代码行数:76，代码来源:adc.c

示例8: ADC1_RCC

void ADC1_RCC(void)
{
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
	RCC_ADCCLKConfig(RCC_PCLK2_Div6);
}

开发者ID:andyzhao365，项目名称:GuodianBeijingGuangyuACIntoDCDetectionDevice，代码行数:6，代码来源:adc.c

示例9: RC5_Init

/**
  * @brief  Initialize the RC5 decoder module ( Time range)
  * @param  None
  * @retval None
  */
void RC5_Init(void)
{ 
  GPIO_InitTypeDef GPIO_InitStructure;
  NVIC_InitTypeDef NVIC_InitStructure;
  TIM_ICInitTypeDef TIM_ICInitStructure;
  
  /*  Clock Configuration for TIMER */
  RCC_APB1PeriphClockCmd(IR_TIM_CLK , ENABLE);

  /* Enable Button GPIO clock */
  RCC_AHBPeriphClockCmd(IR_GPIO_PORT_CLK , ENABLE);
 
  /* Pin configuration: input floating */
  GPIO_InitStructure.GPIO_Pin = IR_GPIO_PIN;
  GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStructure.GPIO_PuPd  = GPIO_PuPd_NOPULL;
  GPIO_Init(IR_GPIO_PORT, &GPIO_InitStructure);
  
  GPIO_PinAFConfig( IR_GPIO_PORT,IR_GPIO_SOURCE,GPIO_AF_2);
  
  /* Enable the TIM global Interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = IR_TIM_IRQn ;
  NVIC_InitStructure.NVIC_IRQChannelPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
    
  /* TIMER frequency input */
  TIM_PrescalerConfig(IR_TIM, TIM_PRESCALER, TIM_PSCReloadMode_Immediate);
  
  TIM_ICStructInit(&TIM_ICInitStructure);
  
  /* TIM configuration */
  TIM_ICInitStructure.TIM_Channel = IR_TIM_Channel;
  TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Falling;
  TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;
  TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;
  TIM_ICInitStructure.TIM_ICFilter = 0x0;
  
  TIM_PWMIConfig(IR_TIM, &TIM_ICInitStructure); 

  /* Timer Clock */
  TIMCLKValueKHz = TIM_GetCounterCLKValue()/1000; 

  /* Select the TIM Input Trigger: TI2FP2 */
  TIM_SelectInputTrigger(IR_TIM, TIM_TS_TI2FP2);

  /* Select the slave Mode: Reset Mode */
  TIM_SelectSlaveMode(IR_TIM, TIM_SlaveMode_Reset);

  /* Enable the Master/Slave Mode */
  TIM_SelectMasterSlaveMode(IR_TIM, TIM_MasterSlaveMode_Enable);

  /* Configures the TIM Update Request Interrupt source: counter overflow */
  TIM_UpdateRequestConfig(IR_TIM,  TIM_UpdateSource_Regular);
   
  RC5TimeOut = TIMCLKValueKHz * RC5_TIME_OUT_US/1000;

  /* Set the TIM auto-reload register for each IR protocol */
  IR_TIM->ARR = RC5TimeOut;
  
  /* Clear update flag */
  TIM_ClearFlag(IR_TIM, TIM_FLAG_Update);

  /* Enable TIM Update Event Interrupt Request */
  TIM_ITConfig(IR_TIM, TIM_IT_Update, ENABLE);
    
  /* Enable the CC2/CC1 Interrupt Request */
  TIM_ITConfig(IR_TIM, TIM_IT_CC2, ENABLE);
    /* Enable the CC2/CC1 Interrupt Request */
  TIM_ITConfig(IR_TIM, TIM_IT_CC1, ENABLE);

  /* Enable the timer */
  TIM_Cmd(IR_TIM, ENABLE);  
  
  if (CECDemoStatus == 0)
  {
    /* Set the LCD Back Color */
    LCD_SetBackColor(LCD_COLOR_RED);
    
    /* Set the LCD Text Color */
    LCD_SetTextColor(LCD_COLOR_GREEN);    
    LCD_DisplayStringLine(LCD_LINE_0, "   STM320518-EVAL   ");
    LCD_DisplayStringLine(LCD_LINE_1, " RC5 InfraRed Demo  ");
    LCD_SetBackColor(LCD_COLOR_BLUE);
    
    /* Set the LCD Text Color */
    LCD_SetTextColor(LCD_COLOR_WHITE);  
  }
  
  /* Bit time range */
  RC5MinT = (RC5_T_US - RC5_T_TOLERANCE_US) * TIMCLKValueKHz / 1000;
  RC5MaxT = (RC5_T_US + RC5_T_TOLERANCE_US) * TIMCLKValueKHz / 1000;
  RC5Min2T = (2 * RC5_T_US - RC5_T_TOLERANCE_US) * TIMCLKValueKHz / 1000;
//.........这里部分代码省略.........

开发者ID:Montanari9，项目名称:InfraRED，代码行数:101，代码来源:rc5_decode.c

示例10: main

int main(void)
{
	//Enable clocks
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);

	//Configure PA0, PA1 and PA2 as analog inputs
	G.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2;
	G.GPIO_Mode = GPIO_Mode_AN;
	G.GPIO_OType = GPIO_OType_PP;
	G.GPIO_PuPd = GPIO_PuPd_NOPULL;
	G.GPIO_Speed = GPIO_Speed_2MHz;
	GPIO_Init(GPIOA, &G);

	//Configure ADC for DMA
	A.ADC_ContinuousConvMode = DISABLE;
	A.ADC_DataAlign = ADC_DataAlign_Right;
	A.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
	A.ADC_Resolution = ADC_Resolution_12b;
	A.ADC_ScanDirection = ADC_ScanDirection_Upward;
	ADC_Init(ADC1, &A);
	ADC_Cmd(ADC1, ENABLE);
	ADC_DMACmd(ADC1, ENABLE);

	//Configure the corresponding DMA stream for the ADC
	D.DMA_BufferSize = 3;										//Three variables
	D.DMA_DIR = DMA_DIR_PeripheralSRC;							//ADC peripheral is the data source
	D.DMA_M2M = DMA_M2M_Disable;								//Disable memory to memory mode
	D.DMA_MemoryBaseAddr = (uint32_t) &Conversions[0];			//Pointer to variables array
	D.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;			//'Conversions' is 16bits large (HWord)
	D.DMA_MemoryInc = DMA_MemoryInc_Enable;						//Enable memory increment
	D.DMA_Mode = DMA_Mode_Normal;								//Non circular DMA mode
	D.DMA_PeripheralBaseAddr = (uint32_t) &ADC1->DR;			//Pointer to ADC data register!
	D.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;	//ADC1->DR is 16bits!
	D.DMA_PeripheralInc = DMA_PeripheralInc_Disable;			//Disable peripheral increment
	D.DMA_Priority = DMA_Priority_Low;							//A low priority DMA stream, not a big deal here!
	DMA_Init(DMA1_Channel1, &D);
	DMA_Cmd(DMA1_Channel1, ENABLE);

	//Enable transfer complete interrupt for DMA1 channel 1
	DMA_ClearITPendingBit(DMA1_IT_TC1);
	DMA_ITConfig(DMA1_Channel1, DMA_IT_TC, ENABLE);

	N.NVIC_IRQChannel = DMA1_Channel1_IRQn;
	N.NVIC_IRQChannelPriority = 1;
	N.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&N);

	//Configure channels to be converted
	ADC_ChannelConfig(ADC1, ADC_Channel_0, ADC_SampleTime_239_5Cycles);
	ADC_ChannelConfig(ADC1, ADC_Channel_1, ADC_SampleTime_239_5Cycles);
	ADC_ChannelConfig(ADC1, ADC_Channel_2, ADC_SampleTime_239_5Cycles);

	//Wait for ADC to be ready!
	while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_ADRDY));

	while(1)
	{
		//Disable the DMA channel
		DMA_Cmd(DMA1_Channel1, DISABLE);

		//Re-initialize channel
		DMA_Init(DMA1_Channel1, &D);

		//Enable the DMA channel
		DMA_Cmd(DMA1_Channel1, ENABLE);

		//Kick off the first conversion!
		ADC_StartOfConversion(ADC1);

		//Wait for converted data
		while(!Converted);

		//Reset conversion flag (Breakpoint to read data here!)
		Converted = 0;
	}
}

开发者ID:pyrohaz，项目名称:STM32F0-ADCModes，代码行数:78，代码来源:main.c

示例11: init_i2c

//initialize the i2c periperal
void init_i2c(void){
    //RCC_APBPeriphClockCmd(RCC_APBPeriph_SYSCFG, ENABLE); //enable for i2c fast mode
    //SYSCFG_I2CFastModePlusConfig(SYSCFG_CFGR1_I2C_FMP_PB6|SYSCFG_CFGR1_I2C_FMP_PB7, ENABLE);
        
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);
    RCC_I2CCLKConfig(RCC_I2C1CLK_SYSCLK);
    GPIO_PinAFConfig(GPIOB, GPIO_PinSource6, GPIO_AF_1);
    GPIO_PinAFConfig(GPIOB, GPIO_PinSource7, GPIO_AF_1);

    GPIO_InitTypeDef GPIOB_InitStruct = {
        .GPIO_Pin = GPIO_Pin_6|GPIO_Pin_7,
        .GPIO_Speed = GPIO_Speed_50MHz,
        .GPIO_Mode = GPIO_Mode_AF,
        .GPIO_OType = GPIO_OType_OD,
        .GPIO_PuPd = GPIO_PuPd_UP
    };
    GPIO_Init(GPIOB, &GPIOB_InitStruct);
    GPIO_PinLockConfig(GPIOB, GPIO_PinSource6);
    GPIO_PinLockConfig(GPIOB, GPIO_PinSource7);
    
    I2C_InitTypeDef I2C_InitStructure = {
        //.I2C_Timing = 0x20310A0D,
        .I2C_Timing = 0x0010020A,
        .I2C_AnalogFilter = I2C_AnalogFilter_Enable,
        .I2C_DigitalFilter = 0x00,
        .I2C_Mode = I2C_Mode_I2C,
        .I2C_OwnAddress1 = 0x00,
        .I2C_Ack = I2C_Ack_Enable,
        .I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit
    };
    I2C_Init(I2C1, &I2C_InitStructure);
    //I2C_ITConfig(USART1, I2C_IT_NACKI, ENABLE);
    //NVIC_EnableIRQ(I2C1_IRQn);
    I2C_Cmd(I2C1, ENABLE);
}

void I2C_WrReg(uint8_t Reg, uint8_t Val){
    //Wait until I2C isn't busy
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY) == SET);

	//"Handle" a transfer - The STM32F0 series has a shocking I2C interface...
	//...Regardless! Send the address of the HMC sensor down the I2C Bus and generate
	//a start saying we're going to write one byte. I'll be completely honest,
	//the I2C peripheral doesn't make too much sense to me and a lot of the code is
	//from the Std peripheral library
	I2C_TransferHandling(I2C1, 0x78, 1, I2C_Reload_Mode, I2C_Generate_Start_Write);

	//Ensure the transmit interrupted flag is set
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_TXIS) == RESET);

	//Send the address of the register we wish to write to
	I2C_SendData(I2C1, Reg);

	//Ensure that the transfer complete reload flag is Set, essentially a standard
	//TC flag
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_TCR) == RESET);

	//Now that the HMC5883L knows which register we want to write to, send the address
	//again and ensure the I2C peripheral doesn't add any start or stop conditions
	I2C_TransferHandling(I2C1, 0x78, 1, I2C_AutoEnd_Mode, I2C_No_StartStop);

	//Again, wait until the transmit interrupted flag is set
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_TXIS) == RESET);

	//Send the value you wish you write to the register
	I2C_SendData(I2C1, Val);

	//Wait for the stop flag to be set indicating a stop condition has been sent
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_STOPF) == RESET);

	//Clear the stop flag for the next potential transfer
	I2C_ClearFlag(I2C1, I2C_FLAG_STOPF);
}

void i2c_out(uint8_t val){
    //Wait until I2C isn't busy
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY) == SET);

	//"Handle" a transfer - The STM32F0 series has a shocking I2C interface...
	//...Regardless! Send the address of the HMC sensor down the I2C Bus and generate
	//a start saying we're going to write one byte. I'll be completely honest,
	//the I2C peripheral doesn't make too much sense to me and a lot of the code is
	//from the Std peripheral library
	I2C_TransferHandling(I2C1, 0x78, 1, I2C_Reload_Mode, I2C_Generate_Start_Write);

	//Ensure the transmit interrupted flag is set
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_TXIS) == RESET);

	//Send the address of the register we wish to write to
	I2C_SendData(I2C1, val);

	//Ensure that the transfer complete reload flag is Set, essentially a standard
	//TC flag
	while(I2C_GetFlagStatus(I2C1, I2C_FLAG_TCR) == RESET);

	//Clear the stop flag for the next potential transfer
	I2C_ClearFlag(I2C1, I2C_FLAG_STOPF);
}
//.........这里部分代码省略.........

开发者ID:peterfillmore，项目名称:RuxconBadge2015，代码行数:101，代码来源:i2c_func.c

示例12: EXT_SRAM_Configuration

void EXT_SRAM_Configuration(void)
{
    FSMC_NORSRAMInitTypeDef  FSMC_NORSRAMInitStructure;
    FSMC_NORSRAMTimingInitTypeDef  p;

    /* FSMC GPIO configure */
    {
        GPIO_InitTypeDef GPIO_InitStructure;
        RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOE | RCC_APB2Periph_GPIOF
                               | RCC_APB2Periph_GPIOG, ENABLE);
        RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);

        GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_AF_PP;
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

        /*
        FSMC_D0 ~ FSMC_D3
        PD14 FSMC_D0   PD15 FSMC_D1   PD0  FSMC_D2   PD1  FSMC_D3
        */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_14 | GPIO_Pin_15;
        GPIO_Init(GPIOD,&GPIO_InitStructure);

        /*
        FSMC_D4 ~ FSMC_D12
        PE7 ~ PE15  FSMC_D4 ~ FSMC_D12
        */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7 | GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10
                                      | GPIO_Pin_11 | GPIO_Pin_12 | GPIO_Pin_13 | GPIO_Pin_14 | GPIO_Pin_15;
        GPIO_Init(GPIOE,&GPIO_InitStructure);

        /* FSMC_D13 ~ FSMC_D15   PD8 ~ PD10 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10;
        GPIO_Init(GPIOD,&GPIO_InitStructure);

        /*
        FSMC_A0 ~ FSMC_A5   FSMC_A6 ~ FSMC_A9
        PF0     ~ PF5       PF12    ~ PF15
        */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3
                                      | GPIO_Pin_4 | GPIO_Pin_5 | GPIO_Pin_12 | GPIO_Pin_13 | GPIO_Pin_14 | GPIO_Pin_15;
        GPIO_Init(GPIOF,&GPIO_InitStructure);

        /* FSMC_A10 ~ FSMC_A15  PG0 ~ PG5 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3 | GPIO_Pin_4 | GPIO_Pin_5;
        GPIO_Init(GPIOG,&GPIO_InitStructure);

        /* FSMC_A16 ~ FSMC_A18  PD11 ~ PD13 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 | GPIO_Pin_12 | GPIO_Pin_13;
        GPIO_Init(GPIOD,&GPIO_InitStructure);

        /* RD-PD4 WR-PD5 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4 | GPIO_Pin_5;
        GPIO_Init(GPIOD,&GPIO_InitStructure);

        /* NBL0-PE0 NBL1-PE1 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1;
        GPIO_Init(GPIOE,&GPIO_InitStructure);

        /* NE1/NCE2 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;
        GPIO_Init(GPIOD,&GPIO_InitStructure);
        /* NE2 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
        GPIO_Init(GPIOG,&GPIO_InitStructure);
        /* NE3 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
        GPIO_Init(GPIOG,&GPIO_InitStructure);
        /* NE4 */
        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
        GPIO_Init(GPIOG,&GPIO_InitStructure);
    }
    /* FSMC GPIO configure */

    /*-- FSMC Configuration ------------------------------------------------------*/
    p.FSMC_AddressSetupTime = 0;
    p.FSMC_AddressHoldTime = 0;
    p.FSMC_DataSetupTime = 2;
    p.FSMC_BusTurnAroundDuration = 0;
    p.FSMC_CLKDivision = 0;
    p.FSMC_DataLatency = 0;
    p.FSMC_AccessMode = FSMC_AccessMode_A;

    FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM3;
    FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable;
    FSMC_NORSRAMInitStructure.FSMC_MemoryType = FSMC_MemoryType_SRAM;
    FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;
    FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode = FSMC_BurstAccessMode_Disable;
    FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait = FSMC_AsynchronousWait_Disable;
    FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;
    FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;
    FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;
    FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable;
    FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;
    FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Disable;
    FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable;
    FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &p;
    FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &p;
 
    FSMC_NORSRAMInit(&FSMC_NORSRAMInitStructure);

//.........这里部分代码省略.........

开发者ID:malooei，项目名称:malooei-workspace，代码行数:101，代码来源:board.c

示例13: UART1_DMA_init

void UART1_DMA_init(u32 baud)
{
	
  GPIO_InitTypeDef GPIO_InitStructure;
	DMA_InitTypeDef DMA_InitStructure;
	USART_InitTypeDef USART_InitStructure;
	NVIC_InitTypeDef NVIC_InitStructure;
	 
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1|RCC_APB2Periph_GPIOA|RCC_APB2Periph_AFIO, ENABLE);
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);

	 //USART1_TX   PA.9
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_Init(GPIOA, &GPIO_InitStructure);
 
	//USART1_RX	  PA.10
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
	GPIO_Init(GPIOA, &GPIO_InitStructure); 
	
	NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel5_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);

	//Usart1 DMA 配置
	/* USARTy RX DMA1 Channel --DMA1_Channel5(triggered by USART1 Rx event) Config */
	DMA_DeInit(DMA1_Channel5); 												// 
	DMA_InitStructure.DMA_PeripheralBaseAddr = USART1_DR_Address;			//DMA通道1的地址
	DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)USART1_RxBuffer;		//DMA传送地址
	DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;						//传送方向 USART是外设
	DMA_InitStructure.DMA_BufferSize = 8;						//传送内存大小 ,注意内存大小为DMA传送地址的数组大小
	DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;		//传送源地址不递增
	DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;					//传送内存地址递增
	DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;	//源地址的数据长度是8位
	DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;			//传送的目的地址是8位宽度
	DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;							//传送模式循环
	DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh;					//优先级设置
	DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;							//DMA通道没有设置为内存到内存传送 
	DMA_Init(DMA1_Channel5, &DMA_InitStructure);							//
	
		//USART 初始化设置

	USART_InitStructure.USART_BaudRate = baud;//一般设置为9600;
	USART_InitStructure.USART_WordLength = USART_WordLength_8b;
	USART_InitStructure.USART_StopBits = USART_StopBits_1;
	USART_InitStructure.USART_Parity = USART_Parity_No;
	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
	USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
	USART_Init(USART1, &USART_InitStructure);
	
	/* Enable USARTy DMA Rx request */
	USART_DMACmd(USART1, USART_DMAReq_Rx, ENABLE);
	/* 允许DMA1通道1传输结束中断 */
	DMA_ITConfig(DMA1_Channel5,DMA_IT_TC, ENABLE);
	/* Enable USARTy RX DMA1 Channel */
	DMA_Cmd(DMA1_Channel5, ENABLE);

  USART_Cmd(USART1, ENABLE);                    //使能串口 

}

开发者ID:EasternRise，项目名称:AGV，代码行数:64，代码来源:compass.c

示例14: Sensor1_6_Configration

void Sensor1_6_Configration(void)
{
	NVIC_InitTypeDef NVIC_InitStructure;
	DMA_InitTypeDef DMA_InitStructure;
	USART_InitTypeDef USART_InitStructure;
	//---------------------串口功能配置---------------------
	//打开串口对应的外设时钟  
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2 , ENABLE); 
	//串口发DMA配置  
	//启动DMA时钟
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
	//DMA发送中断设置
	NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel4_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 3;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);
	//DMA1通道4配置
	DMA_DeInit(DMA1_Channel4);
	//外设地址
	DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)(&USART1->DR);
	//内存地址
	DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)Uart_Send_Buffer;
	//dma传输方向单向
	DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
	//设置DMA在传输时缓冲区的长度
	DMA_InitStructure.DMA_BufferSize = 100;
	//设置DMA的外设递增模式，一个外设
	DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
	//设置DMA的内存递增模式
	DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
	//外设数据字长
	DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
	//内存数据字长
	DMA_InitStructure.DMA_MemoryDataSize = DMA_PeripheralDataSize_Byte;
	//设置DMA的传输模式
	DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
	//设置DMA的优先级别
	DMA_InitStructure.DMA_Priority = DMA_Priority_High;
	//设置DMA的2个memory中的变量互相访问
	DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
	DMA_Init(DMA1_Channel4,&DMA_InitStructure);
	DMA_ITConfig(DMA1_Channel4,DMA_IT_TC,ENABLE);
	
	//使能通道4
	//DMA_Cmd(DMA1_Channel4, ENABLE);

	//串口收DMA配置  
	//启动DMA时钟
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
	//DMA1通道5配置
	DMA_DeInit(DMA1_Channel5);
	//外设地址
	DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)(&USART1->DR);
	//内存地址
	DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)Uart_Rx2;
	//dma传输方向单向
	DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
	//设置DMA在传输时缓冲区的长度
	DMA_InitStructure.DMA_BufferSize = UART_RX_LEN;
	//设置DMA的外设递增模式，一个外设
	DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
	//设置DMA的内存递增模式
	DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
	//外设数据字长
	DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
	//内存数据字长
	DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
	//设置DMA的传输模式
	DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
	//设置DMA的优先级别
	DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh;
	//设置DMA的2个memory中的变量互相访问
	DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
	DMA_Init(DMA1_Channel5,&DMA_InitStructure);

	//使能通道5
	DMA_Cmd(DMA1_Channel5,ENABLE);
	
	  
    //初始化参数  
    //USART_InitStructure.USART_BaudRate = DEFAULT_BAUD;  
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;  
    USART_InitStructure.USART_StopBits = USART_StopBits_1;  
    USART_InitStructure.USART_Parity = USART_Parity_No;  
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;  
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;    
    USART_InitStructure.USART_BaudRate = DEFAULT_BAUD; 
	//初始化串口 
    USART_Init(USART1,&USART_InitStructure);  
    //TXE发送中断,TC传输完成中断,RXNE接收中断,PE奇偶错误中断,可以是多个   
    //USART_ITConfig(USART1,USART_IT_RXNE,ENABLE);
	
	//中断配置
	USART_ITConfig(USART1,USART_IT_TC,DISABLE);
	USART_ITConfig(USART1,USART_IT_RXNE,DISABLE);
	USART_ITConfig(USART1,USART_IT_IDLE,ENABLE);

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ RCC_APB1PeriphResetCmd函数代码示例发布时间：2022-05-30

C++ RCC_AHB1PeriphClockCmd函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19287|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：10021|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8344|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8714|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8658|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9688|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8647|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8014|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8683|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7550|2022-11-06

客服电话

电子邮件

C++ RCC_AHBPeriphClockCmd函数代码示例

示例1: ADC_Config

示例2: TIM_Config

示例3: adcInit

示例4: TIM_Config

示例5: init_prog_canal

示例6: systemInit

示例7: AdcInit34

示例8: ADC1_RCC

示例9: RC5_Init

示例10: main

示例11: init_i2c

示例12: EXT_SRAM_Configuration

示例13: UART1_DMA_init

示例14: Sensor1_6_Configration

请发表评论

全部评论

上一篇：

下一篇：

CVE-2022-2115

dustinvtran/ml-videos: A collection of v

ravikumar001/maven

更的笔顺,体会更的笔画,理会更的部首

ceejbot/LOUDBOT: AUTOMATED SHOUTING FOR

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053