C++ QIXIS_READ函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中QIXIS_READ函数的典型用法代码示例。如果您正苦于以下问题：C++ QIXIS_READ函数的具体用法？C++ QIXIS_READ怎么用？C++ QIXIS_READ使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了QIXIS_READ函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: get_board_ddr_clk

unsigned long get_board_ddr_clk(void)
{
	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
	/* use accurate clock measurement */
	int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]);
	int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
	u32 val;

	val =  freq * base;
	if (val) {
		debug("DDR Clock measurement is: %d\n", val);
		return val;
	} else {
		printf("Warning: DDR clock measurement is invalid, ");
		printf("using value from brdcfg1.\n");
	}
#endif

	switch ((ddrclk_conf & 0x30) >> 4) {
	case QIXIS_DDRCLK_100:
		return 100000000;
	case QIXIS_DDRCLK_125:
		return 125000000;
	case QIXIS_DDRCLK_133:
		return 133333333;
	}
	return 66666666;
}

开发者ID:01hyang，项目名称:u-boot，代码行数:29，代码来源:t208xqds.c

示例2: platform_diu_init

int platform_diu_init(unsigned int xres, unsigned int yres, const char *port)
{
	u32 pixel_format;
	u8 sw;

	/*Route I2C4 to DIU system as HSYNC/VSYNC*/
	sw = QIXIS_READ(brdcfg[5]);
	QIXIS_WRITE(brdcfg[5],
		    ((sw & ~(BRDCFG5_IMX_MASK)) | (BRDCFG5_IMX_DIU)));

	/*Configure Display ouput port as HDMI*/
	sw = QIXIS_READ(brdcfg[15]);
	QIXIS_WRITE(brdcfg[15],
		    ((sw & ~(BRDCFG15_LCDPD_MASK | BRDCFG15_DIUSEL_MASK))
		      | (BRDCFG15_LCDPD_ENABLED | BRDCFG15_DIUSEL_HDMI)));

	pixel_format = cpu_to_le32(AD_BYTE_F | (3 << AD_ALPHA_C_SHIFT) |
		(0 << AD_BLUE_C_SHIFT) | (1 << AD_GREEN_C_SHIFT) |
		(2 << AD_RED_C_SHIFT) | (8 << AD_COMP_3_SHIFT) |
		(8 << AD_COMP_2_SHIFT) | (8 << AD_COMP_1_SHIFT) |
		(8 << AD_COMP_0_SHIFT) | (3 << AD_PIXEL_S_SHIFT));

	printf("DIU:   Switching to monitor @ %ux%u\n",  xres, yres);


	return fsl_diu_init(xres, yres, pixel_format, 0);
}

开发者ID:01hyang，项目名称:u-boot，代码行数:27，代码来源:diu.c

示例3: checkboard

int checkboard(void)
{
	u8 sw;

	sw = QIXIS_READ(arch);
	printf("Board: %s, ", CONFIG_IDENT_STRING);
	printf("Board Arch: V%d, ", sw >> 4);
	printf("Board version: %c, boot from ", (sw & 0xf) + 'A' - 1);

	sw = QIXIS_READ(brdcfg[0]);
	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

	if (sw < 0x8)
		printf("vBank: %d\n", sw);
	else if (sw == 0x9)
		puts("NAND\n");
	else
		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);

	printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));

	puts("SERDES1 Reference : ");
	printf("Clock1 = 156.25MHz ");
	printf("Clock2 = 156.25MHz");

	puts("\nSERDES2 Reference : ");
	printf("Clock1 = 100MHz ");
	printf("Clock2 = 100MHz\n");

	return 0;
}

开发者ID:CZ-NIC，项目名称:u-boot-turris，代码行数:31，代码来源:ls2085ardb.c

示例4: qixis_dump_switch

void qixis_dump_switch(void)
{
	int i, nr_of_cfgsw;

	QIXIS_WRITE(cms[0], 0x00);
	nr_of_cfgsw = QIXIS_READ(cms[1]);

	puts("DIP switch settings dump:\n");
	for (i = 1; i <= nr_of_cfgsw; i++) {
		QIXIS_WRITE(cms[0], i);
		printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
	}
}

开发者ID:CZ-NIC，项目名称:u-boot-turris，代码行数:13，代码来源:ls2085ardb.c

示例5: checkboard

int checkboard(void)
{
#ifdef CONFIG_TFABOOT
	enum boot_src src = get_boot_src();
#endif
	char buf[64];
#ifndef CONFIG_SD_BOOT
	u8 sw;
#endif

	puts("Board: LS1043AQDS, boot from ");

#ifdef CONFIG_TFABOOT
	if (src == BOOT_SOURCE_SD_MMC)
		puts("SD\n");
	else {
#endif

#ifdef CONFIG_SD_BOOT
	puts("SD\n");
#else
	sw = QIXIS_READ(brdcfg[0]);
	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

	if (sw < 0x8)
		printf("vBank: %d\n", sw);
	else if (sw == 0x8)
		puts("PromJet\n");
	else if (sw == 0x9)
		puts("NAND\n");
	else if (sw == 0xF)
		printf("QSPI\n");
	else
		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
#endif

#ifdef CONFIG_TFABOOT
	}
#endif
	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n",
	       QIXIS_READ(id), QIXIS_READ(arch));

	printf("FPGA:  v%d (%s), build %d\n",
	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
	       (int)qixis_read_minor());

	return 0;
}

开发者ID:CogSystems，项目名称:u-boot，代码行数:48，代码来源:ls1043aqds.c

示例6: esdhc_status_fixup

int esdhc_status_fixup(void *blob, const char *compat)
{
	char esdhc0_path[] = "/soc/[email protected]";
	char esdhc1_path[] = "/soc/[email protected]";
	u8 card_id;

	do_fixup_by_path(blob, esdhc0_path, "status", "okay",
			 sizeof("okay"), 1);

	/*
	 * The Presence Detect 2 register detects the installation
	 * of cards in various PCI Express or SGMII slots.
	 *
	 * STAT_PRS2[7:5]: Specifies the type of card installed in the
	 * SDHC2 Adapter slot. 0b111 indicates no adapter is installed.
	 */
	card_id = (QIXIS_READ(present2) & 0xe0) >> 5;

	/* If no adapter is installed in SDHC2, disable SDHC2 */
	if (card_id == 0x7)
		do_fixup_by_path(blob, esdhc1_path, "status", "disabled",
				 sizeof("disabled"), 1);
	else
		do_fixup_by_path(blob, esdhc1_path, "status", "okay",
				 sizeof("okay"), 1);
	return 0;
}

开发者ID:danielschwierzeck，项目名称:u-boot-lantiq，代码行数:27，代码来源:ls1012aqds.c

示例7: board_early_init_f

int board_early_init_f(void)
{
#ifdef CONFIG_HAS_FSL_XHCI_USB
	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
	u32 usb_pwrfault;
#endif
#ifdef CONFIG_LPUART
	u8 uart;
#endif

#ifdef CONFIG_SYS_I2C_EARLY_INIT
	i2c_early_init_f();
#endif
	fsl_lsch2_early_init_f();

#ifdef CONFIG_HAS_FSL_XHCI_USB
	out_be32(&scfg->rcwpmuxcr0, 0x3333);
	out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
	usb_pwrfault =
		(SCFG_USBPWRFAULT_DEDICATED << SCFG_USBPWRFAULT_USB3_SHIFT) |
		(SCFG_USBPWRFAULT_DEDICATED << SCFG_USBPWRFAULT_USB2_SHIFT) |
		(SCFG_USBPWRFAULT_SHARED << SCFG_USBPWRFAULT_USB1_SHIFT);
	out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
#endif

#ifdef CONFIG_LPUART
	/* We use lpuart0 as system console */
	uart = QIXIS_READ(brdcfg[14]);
	uart &= ~CFG_UART_MUX_MASK;
	uart |= CFG_LPUART_EN << CFG_UART_MUX_SHIFT;
	QIXIS_WRITE(brdcfg[14], uart);
#endif

	return 0;
}

开发者ID:CogSystems，项目名称:u-boot，代码行数:35，代码来源:ls1043aqds.c

示例8: ls1021a_mux_mdio

static void ls1021a_mux_mdio(int addr)
{
	u8 brdcfg4;

	brdcfg4 = QIXIS_READ(brdcfg[4]);
	brdcfg4 &= EMI1_MASK;

	switch (addr) {
	case EMI1_RGMII0:
		brdcfg4 |= 0;
		break;
	case EMI1_RGMII1:
		brdcfg4 |= 0x20;
		break;
	case EMI1_RGMII2:
		brdcfg4 |= 0x40;
		break;
	case EMI1_SGMII1:
		brdcfg4 |= 0x60;
		break;
	case EMI1_SGMII2:
		brdcfg4 |= 0x80;
		break;
	default:
		brdcfg4 |= 0xa0;
		break;
	}

	QIXIS_WRITE(brdcfg[4], brdcfg4);
}

开发者ID:13xiaobang，项目名称:mini2440-uboot_2016.01，代码行数:30，代码来源:eth.c

示例9: ft_board_setup

int ft_board_setup(void *blob, bd_t *bd)
{
	u64 base[CONFIG_NR_DRAM_BANKS];
	u64 size[CONFIG_NR_DRAM_BANKS];
	u8 reg;

	/* fixup DT for the two DDR banks */
	base[0] = gd->bd->bi_dram[0].start;
	size[0] = gd->bd->bi_dram[0].size;
	base[1] = gd->bd->bi_dram[1].start;
	size[1] = gd->bd->bi_dram[1].size;

	fdt_fixup_memory_banks(blob, base, size, 2);
	ft_cpu_setup(blob, bd);

#ifdef CONFIG_SYS_DPAA_FMAN
	fdt_fixup_fman_ethernet(blob);
	fdt_fixup_board_enet(blob);
#endif

	reg = QIXIS_READ(brdcfg[0]);
	reg = (reg & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

	/* Disable IFC if QSPI is enabled */
	if (reg == 0xF)
		do_fixup_by_compat(blob, "fsl,ifc",
				   "status", "disabled", 8 + 1, 1);

	return 0;
}

开发者ID:eballetbo，项目名称:u-boot，代码行数:30，代码来源:ls1046aqds.c

示例10: get_board_sys_clk

unsigned long get_board_sys_clk(void)
{
	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);

	switch (sysclk_conf & 0x0f) {
	case QIXIS_SYSCLK_64:
		return 64000000;
	case QIXIS_SYSCLK_83:
		return 83333333;
	case QIXIS_SYSCLK_100:
		return 100000000;
	case QIXIS_SYSCLK_125:
		return 125000000;
	case QIXIS_SYSCLK_133:
		return 133333333;
	case QIXIS_SYSCLK_150:
		return 150000000;
	case QIXIS_SYSCLK_160:
		return 160000000;
	case QIXIS_SYSCLK_166:
		return 166666666;
	}

	return 66666666;
}

开发者ID:eballetbo，项目名称:u-boot，代码行数:25，代码来源:ls1046aqds.c

示例11: board_early_init_r

int board_early_init_r(void)
{
	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);

	/*
	 * Remap Boot flash + PROMJET region to caching-inhibited
	 * so that flash can be erased properly.
	 */

	/* Flush d-cache and invalidate i-cache of any FLASH data */
	flush_dcache();
	invalidate_icache();

	/* invalidate existing TLB entry for flash + promjet */
	disable_tlb(flash_esel);

	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
		0, flash_esel, BOOKE_PAGESZ_256M, 1);

	set_liodns();
#ifdef CONFIG_SYS_DPAA_QBMAN
	setup_portals();
#endif

	/* Disable remote I2C connection to qixis fpga */
	QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE);

	brd_mux_lane_to_slot();
	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);

	return 0;
}

开发者ID:Android4SAM，项目名称:u-boot-at91，代码行数:34，代码来源:t208xqds.c

示例12: set_brdcfg9_for_gtx_clk

static void set_brdcfg9_for_gtx_clk(void)
{
	u8 brdcfg9;
	brdcfg9 = QIXIS_READ(brdcfg[9]);
	brdcfg9 |= (1 << 5);
	QIXIS_WRITE(brdcfg[9], brdcfg9);
}

开发者ID:AhmadQasim，项目名称:GPU-Virtualization，代码行数:7，代码来源:eth.c

示例13: config_board_mux

int config_board_mux(int ctrl_type)
{
	u8 reg12, reg14;

	reg12 = QIXIS_READ(brdcfg[12]);
	reg14 = QIXIS_READ(brdcfg[14]);

	switch (ctrl_type) {
	case MUX_TYPE_CAN:
		config_etseccm_source(GE2_CLK125);
		reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_CAN);
		break;
	case MUX_TYPE_IIC2:
		reg14 = SET_SDHC_MUX_SEL(reg14, PIN_MUX_SEL_IIC2);
		break;
	case MUX_TYPE_RGMII:
		reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_RGMII);
		break;
	case MUX_TYPE_SAI:
		config_etseccm_source(GE2_CLK125);
		reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_SAI);
		break;
	case MUX_TYPE_SDHC:
		reg14 = SET_SDHC_MUX_SEL(reg14, PIN_MUX_SEL_SDHC);
		break;
	case MUX_TYPE_SD_PCI4:
		reg12 = 0x38;
		break;
	case MUX_TYPE_SD_PC_SA_SG_SG:
		reg12 = 0x01;
		break;
	case MUX_TYPE_SD_PC_SA_PC_SG:
		reg12 = 0x01;
		break;
	case MUX_TYPE_SD_PC_SG_SG:
		reg12 = 0x21;
		break;
	default:
		printf("Wrong mux interface type\n");
		return -1;
	}

	QIXIS_WRITE(brdcfg[12], reg12);
	QIXIS_WRITE(brdcfg[14], reg14);

	return 0;
}

开发者ID:eballetbo，项目名称:u-boot，代码行数:47，代码来源:ls1021aqds.c

示例14: checkboard

int checkboard(void)
{
	char buf[64];
	u8 sw;
	struct cpu_type *cpu = gd->arch.cpu;
	static const char *freq[4] = {
		"100.00MHZ(from 8T49N222A)", "125.00MHz",
		"156.25MHZ", "100.00MHz"
	};

	printf("Board: %sQDS, ", cpu->name);
	sw = QIXIS_READ(arch);
	printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
	printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);

#ifdef CONFIG_SDCARD
	puts("SD/MMC\n");
#elif CONFIG_SPIFLASH
	puts("SPI\n");
#else
	sw = QIXIS_READ(brdcfg[0]);
	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

	if (sw < 0x8)
		printf("vBank%d\n", sw);
	else if (sw == 0x8)
		puts("Promjet\n");
	else if (sw == 0x9)
		puts("NAND\n");
	else
		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
#endif

	printf("FPGA: v%d (%s), build %d", (int)QIXIS_READ(scver),
	       qixis_read_tag(buf), (int)qixis_read_minor());
	/* the timestamp string contains "\n" at the end */
	printf(" on %s", qixis_read_time(buf));

	puts("SERDES Reference Clocks:\n");
	sw = QIXIS_READ(brdcfg[2]);
	printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[sw >> 6],
	       freq[(sw >> 4) & 0x3]);
	printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[(sw & 0xf) >> 2],
	       freq[sw & 0x3]);

	return 0;
}

开发者ID:01hyang，项目名称:u-boot，代码行数:47，代码来源:t208xqds.c

示例15: set_altbank

/* Set the boot bank to the alternate bank */
void set_altbank(void)
{
	u8 reg;

	reg = QIXIS_READ(brdcfg[0]);
	reg = (reg & ~QIXIS_LBMAP_MASK) | QIXIS_LBMAP_ALTBANK;
	QIXIS_WRITE(brdcfg[0], reg);
}

开发者ID:AeroGirl，项目名称:u-boot-kern3.2，代码行数:9，代码来源:qixis.c

示例16: ls2080a_qds_enable_SFP_TX

static void ls2080a_qds_enable_SFP_TX(u8 muxval)
{
	u8 brdcfg9;

	brdcfg9 = QIXIS_READ(brdcfg[9]);
	brdcfg9 &= ~BRDCFG9_SFPTX_MASK;
	brdcfg9 |= (muxval << BRDCFG9_SFPTX_SHIFT);
	QIXIS_WRITE(brdcfg[9], brdcfg9);
}

开发者ID:96boards-bubblegum，项目名称:u-boot，代码行数:9，代码来源:eth.c

示例17: set_brdcfg9_for_gtx_clk

static void set_brdcfg9_for_gtx_clk(void)
{
	u8 brdcfg9;
	brdcfg9 = QIXIS_READ(brdcfg[9]);
/* Initializing EPHY2 clock to RGMII mode */
	brdcfg9 &= ~(BRDCFG9_EPHY2_MASK);
	brdcfg9 |= (BRDCFG9_EPHY2_VAL);
	QIXIS_WRITE(brdcfg[9], brdcfg9);
}

开发者ID:13xiaobang，项目名称:mini2440-uboot_2016.01，代码行数:9，代码来源:eth.c

示例18: t1040_qds_mux_mdio

static void t1040_qds_mux_mdio(u8 muxval)
{
	u8 brdcfg4;
	if (muxval <= 7) {
		brdcfg4 = QIXIS_READ(brdcfg[4]);
		brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
		brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
		QIXIS_WRITE(brdcfg[4], brdcfg4);
	}
}

开发者ID:13xiaobang，项目名称:mini2440-uboot_2016.01，代码行数:10，代码来源:eth.c

示例19: checkboard

int checkboard(void)
{
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
	char buf[64];
#endif
#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
	u8 sw;
#endif

	puts("Board: LS1021AQDS\n");

#ifdef CONFIG_SD_BOOT
	puts("SD\n");
#elif CONFIG_QSPI_BOOT
	puts("QSPI\n");
#else
	sw = QIXIS_READ(brdcfg[0]);
	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;

	if (sw < 0x8)
		printf("vBank: %d\n", sw);
	else if (sw == 0x8)
		puts("PromJet\n");
	else if (sw == 0x9)
		puts("NAND\n");
	else if (sw == 0x15)
		printf("IFCCard\n");
	else
		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
#endif

#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
	printf("Sys ID:0x%02x, Sys Ver: 0x%02x\n",
	       QIXIS_READ(id), QIXIS_READ(arch));

	printf("FPGA:  v%d (%s), build %d\n",
	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
	       (int)qixis_read_minor());
#endif

	return 0;
}

开发者ID:eballetbo，项目名称:u-boot，代码行数:42，代码来源:ls1021aqds.c

示例20: get_board_ddr_clk

unsigned long get_board_ddr_clk(void)
{
	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);

	switch ((ddrclk_conf & 0x30) >> 4) {
	case QIXIS_DDRCLK_100:
		return 100000000;
	case QIXIS_DDRCLK_125:
		return 125000000;
	case QIXIS_DDRCLK_133:
		return 133333333;
	}
	return 66666666;
}

开发者ID:eballetbo，项目名称:u-boot，代码行数:14，代码来源:ls1021aqds.c

注：本文中的QIXIS_READ函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ QIconSet函数代码示例发布时间：2022-05-30

C++ QIO_CHANNEL函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19283|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：10018|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8343|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8712|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8657|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9686|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8646|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8014|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8683|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7550|2022-11-06

客服电话

电子邮件

C++ QIXIS_READ函数代码示例

示例1: get_board_ddr_clk

示例2: platform_diu_init

示例3: checkboard

示例4: qixis_dump_switch

示例5: checkboard

示例6: esdhc_status_fixup

示例7: board_early_init_f

示例8: ls1021a_mux_mdio

示例9: ft_board_setup

示例10: get_board_sys_clk

示例11: board_early_init_r

示例12: set_brdcfg9_for_gtx_clk

示例13: config_board_mux

示例14: checkboard

示例15: set_altbank

示例16: ls2080a_qds_enable_SFP_TX

示例17: set_brdcfg9_for_gtx_clk

示例18: t1040_qds_mux_mdio

示例19: checkboard

示例20: get_board_ddr_clk

请发表评论

全部评论

上一篇：

下一篇：

delphi学习笔记的例子

librespeed/speedtest: Self-hosted Speedt

CVE-2022-1948

avehtari/BDA_m_demos: Bayesian Data Anal

四维彩超怎么看性别？四维看男孩女孩诀窍

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053