static uint8_t MS_Host_SendCommand(USB_ClassInfo_MS_Host_t* const MSInterfaceInfo,
                                   MS_CommandBlockWrapper_t* const SCSICommandBlock,
                                   const void* const BufferPtr)
{
	uint8_t ErrorCode = PIPE_RWSTREAM_NoError;

	SCSICommandBlock->Signature = MS_CBW_SIGNATURE;
	SCSICommandBlock->Tag       = ++MSInterfaceInfo->State.TransactionTag;

	if (MSInterfaceInfo->State.TransactionTag == 0xFFFFFFFF)
	  MSInterfaceInfo->State.TransactionTag = 1;

	Pipe_SelectPipe(MSInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(SCSICommandBlock, sizeof(MS_CommandBlockWrapper_t),
	                                      NULL)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	Pipe_ClearOUT();
	Pipe_WaitUntilReady();

	Pipe_Freeze();

	if ((BufferPtr != NULL) &&
	    ((ErrorCode = MS_Host_SendReceiveData(MSInterfaceInfo, SCSICommandBlock, (void*)BufferPtr)) != PIPE_RWSTREAM_NoError))
	{
		Pipe_Freeze();
		return ErrorCode;
	}

	return ErrorCode;
}

uint8_t MIDI_Host_Flush(USB_ClassInfo_MIDI_Host_t* const MIDIInterfaceInfo)
{
	if ((USB_HostState != HOST_STATE_Configured) || !(MIDIInterfaceInfo->State.IsActive))
	  return PIPE_RWSTREAM_DeviceDisconnected;

	uint8_t ErrorCode;

	Pipe_SelectPipe(MIDIInterfaceInfo->Config.DataOUTPipe.Address);
	Pipe_Unfreeze();

	if (Pipe_BytesInPipe())
	{
		Pipe_ClearOUT();

		if ((ErrorCode = Pipe_WaitUntilReady()) != PIPE_READYWAIT_NoError)
		{
			Pipe_Freeze();
			return ErrorCode;
		}
	}

	Pipe_Freeze();

	return PIPE_READYWAIT_NoError;
}

/** Routine to send the current CBW to the device, and increment the Tag value as needed.
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
static uint8_t MassStore_SendCommand(void)
{
	uint8_t ErrorCode = PIPE_RWSTREAM_NoError;

	/* Each transmission should have a unique tag value, excluding values 0 and 0xFFFFFFFF */
	if (++MassStore_Tag == 0xFFFFFFFF)
	  MassStore_Tag = 1;

	/* Select the OUT data pipe for CBW transmission */
	Pipe_SelectPipe(MASS_STORE_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	/* Write the CBW command to the OUT pipe */
	if ((ErrorCode = Pipe_Write_Stream_LE(&SCSICommandBlock, sizeof(CommandBlockWrapper_t))) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	/* Send the data in the OUT pipe to the attached device */
	Pipe_ClearOUT();
	
	while(!(Pipe_IsOUTReady()));

	/* Freeze pipe after use */
	Pipe_Freeze();
	
	return PIPE_RWSTREAM_NoError;
}

uint8_t SI_Host_SendBlockHeader(USB_ClassInfo_SI_Host_t* const SIInterfaceInfo,
                                PIMA_Container_t* const PIMAHeader)
{
	uint8_t ErrorCode;

	if ((USB_HostState != HOST_STATE_Configured) || !(SIInterfaceInfo->State.IsActive))
	  return PIPE_RWSTREAM_DeviceDisconnected;

	if (SIInterfaceInfo->State.IsSessionOpen)
	  PIMAHeader->TransactionID = SIInterfaceInfo->State.TransactionID++;

	Pipe_SelectPipe(SIInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(PIMAHeader, PIMA_COMMAND_SIZE(0), NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	uint8_t ParamBytes = (PIMAHeader->DataLength - PIMA_COMMAND_SIZE(0));

	if (ParamBytes)
	{
		if ((ErrorCode = Pipe_Write_Stream_LE(&PIMAHeader->Params, ParamBytes, NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;
	}

	Pipe_ClearOUT();
	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}

static uint8_t SImage_Host_SendBlockHeader(USB_ClassInfo_SI_Host_t* const SIInterfaceInfo, SI_PIMA_Container_t* const PIMAHeader)
{
	uint8_t ErrorCode;
	
	PIMAHeader->TransactionID = SIInterfaceInfo->State.TransactionID++;

	Pipe_SelectPipe(SIInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(PIMAHeader, PIMA_COMMAND_SIZE(0), NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;
	
	uint8_t ParamBytes = (PIMAHeader->DataLength - PIMA_COMMAND_SIZE(0));

	if (ParamBytes)
	{
		if ((ErrorCode = Pipe_Write_Stream_LE(&PIMAHeader->Params, ParamBytes, NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;
	}
	
	Pipe_ClearOUT();	
	Pipe_Freeze();
	
	return PIPE_RWSTREAM_NoError;
}

/** Function to send the PIMA command container to the attached still image device. */
void SImage_SendBlockHeader(void)
{
	/* Unfreeze the data OUT pipe ready for data transmission */
	Pipe_SelectPipe(SIMAGE_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	/* Write the PIMA block to the data OUT pipe */
	Pipe_Write_Stream_LE(&PIMA_SendBlock, PIMA_COMMAND_SIZE(0), NULL);

	/* If the block type is a command, send its parameters (if any) */
	if (PIMA_SendBlock.Type == PIMA_CONTAINER_CommandBlock)
	{
		/* Determine the size of the parameters in the block via the data length attribute */
		uint8_t ParamBytes = (PIMA_SendBlock.DataLength - PIMA_COMMAND_SIZE(0));

		/* Check if any parameters in the command block */
		if (ParamBytes)
		{
			/* Write the PIMA parameters to the data OUT pipe */
			Pipe_Write_Stream_LE(&PIMA_SendBlock.Params, ParamBytes, NULL);
		}

		/* Send the PIMA command block to the attached device */
		Pipe_ClearOUT();
	}

	/* Freeze pipe after use */
	Pipe_Freeze();
}

/** Writes a report to the attached device.
 *
 *  \param[in] ReportOUTData  Buffer containing the report to send to the device
 *  \param[in] ReportLength  Length of the report to send
 */
void WriteNextReport(uint8_t* const ReportOUTData,
                     const uint16_t ReportLength)
{
	if (USB_HostState != HOST_STATE_Configured)
	  return;

	/* Select and unfreeze HID data OUT pipe */
	Pipe_SelectPipe(HID_DATA_OUT_PIPE);

	/* Not all HID devices have an OUT endpoint (some require OUT reports to be sent over the
	 * control endpoint instead) - check to see if the OUT endpoint has been initialized */
	if (Pipe_IsConfigured())
	{
		Pipe_Unfreeze();

		/* Ensure pipe is ready to be written to before continuing */
		if (!(Pipe_IsOUTReady()))
		{
			/* Refreeze the data OUT pipe */
			Pipe_Freeze();

			return;
		}

		/* Write out HID report data */
		Pipe_Write_Stream_LE(ReportOUTData, ReportLength, NULL);

		/* Clear the OUT endpoint, send last data packet */
		Pipe_ClearOUT();

		/* Refreeze the data OUT pipe */
		Pipe_Freeze();
	}
	else
	{
		/* Class specific request to send a HID report to the device */
		USB_ControlRequest = (USB_Request_Header_t)
			{
				.bmRequestType = (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE),
				.bRequest      = HID_REQ_SetReport,
				.wValue        = 0x02,
				.wIndex        = 0x01,
				.wLength       = ReportLength,
			};

		/* Select the control pipe for the request transfer */
		Pipe_SelectPipe(PIPE_CONTROLPIPE);

		/* Send the request to the device */
		USB_Host_SendControlRequest(ReportOUTData);
	}
}

uint8_t SImage_Host_SendData(USB_ClassInfo_SI_Host_t* const SIInterfaceInfo, void* Buffer, const uint16_t Bytes)
{
	uint8_t ErrorCode;

	Pipe_SelectPipe(SIInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();
	
	ErrorCode = Pipe_Write_Stream_LE(Buffer, Bytes, NO_STREAM_CALLBACK);

	Pipe_ClearOUT();
	Pipe_Freeze();
	
	return ErrorCode;
}

/** Sends or receives the transaction's data stage to or from the attached device, reading or
 *  writing to the nominated buffer.
 *
 *  \param[in] SCSICommandBlock  Pointer to a SCSI command block structure being sent to the attached device
 *  \param[in,out]  BufferPtr    Pointer to the data buffer to read from or write to
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
static uint8_t MassStore_SendReceiveData(CommandBlockWrapper_t* const SCSICommandBlock,
                                         void* BufferPtr)
{
	uint8_t  ErrorCode = PIPE_RWSTREAM_NoError;
	uint16_t BytesRem  = SCSICommandBlock->DataTransferLength;

	/* Check the direction of the SCSI command data stage */
	if (SCSICommandBlock->Flags & COMMAND_DIRECTION_DATA_IN)
	{
		/* Wait until the device has replied with some data */
		if ((ErrorCode = MassStore_WaitForDataReceived()) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Select the IN data pipe for data reception */
		Pipe_SelectPipe(MASS_STORE_DATA_IN_PIPE);
		Pipe_Unfreeze();

		/* Read in the block data from the pipe */
		if ((ErrorCode = Pipe_Read_Stream_LE(BufferPtr, BytesRem)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Acknowledge the packet */
		Pipe_ClearIN();
	}
	else
	{
		/* Select the OUT data pipe for data transmission */
		Pipe_SelectPipe(MASS_STORE_DATA_OUT_PIPE);
		Pipe_Unfreeze();

		/* Write the block data to the pipe */
		if ((ErrorCode = Pipe_Write_Stream_LE(BufferPtr, BytesRem)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Acknowledge the packet */
		Pipe_ClearOUT();

		while (!(Pipe_IsOUTReady()))
		{
			if (USB_HostState == HOST_STATE_Unattached)
			  return PIPE_RWSTREAM_DeviceDisconnected;
		}
	}

	/* Freeze used pipe after use */
	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}

uint8_t MIDI_Host_SendEventPacket(USB_ClassInfo_MIDI_Host_t* const MIDIInterfaceInfo,
                                  MIDI_EventPacket_t* const Event)
{
	if ((USB_HostState != HOST_STATE_Configured) || !(MIDIInterfaceInfo->State.IsActive))
	  return HOST_SENDCONTROL_DeviceDisconnected;

	uint8_t ErrorCode;

	Pipe_SelectPipe(MIDIInterfaceInfo->Config.DataOUTPipeNumber);

	if ((ErrorCode = Pipe_Write_Stream_LE(Event, sizeof(MIDI_EventPacket_t), NULL)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	if (!(Pipe_IsReadWriteAllowed()))
	  Pipe_ClearOUT();

	return PIPE_RWSTREAM_NoError;
}

static uint8_t MS_Host_SendReceiveData(USB_ClassInfo_MS_Host_t* const MSInterfaceInfo,
                                       MS_CommandBlockWrapper_t* const SCSICommandBlock,
                                       void* BufferPtr)
{
	uint8_t  ErrorCode = PIPE_RWSTREAM_NoError;
	uint16_t BytesRem  = SCSICommandBlock->DataTransferLength;

	if (SCSICommandBlock->Flags & MS_COMMAND_DIR_DATA_IN)
	{
		if ((ErrorCode = MS_Host_WaitForDataReceived(MSInterfaceInfo)) != PIPE_RWSTREAM_NoError)
		{
			Pipe_Freeze();
			return ErrorCode;
		}

		Pipe_SelectPipe(MSInterfaceInfo->Config.DataINPipeNumber);
		Pipe_Unfreeze();

		if ((ErrorCode = Pipe_Read_Stream_LE(BufferPtr, BytesRem, NULL)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		Pipe_ClearIN();
	}
	else
	{
		Pipe_SelectPipe(MSInterfaceInfo->Config.DataOUTPipeNumber);
		Pipe_Unfreeze();

		if ((ErrorCode = Pipe_Write_Stream_LE(BufferPtr, BytesRem, NULL)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		Pipe_ClearOUT();

		while (!(Pipe_IsOUTReady()))
		{
			if (USB_HostState == HOST_STATE_Unattached)
			  return PIPE_RWSTREAM_DeviceDisconnected;
		}
	}

	Pipe_Freeze();

	return ErrorCode;
}

/** Sends a packet to the remote device on the specified channel.
 *
 * \param[in] Data        Pointer to a buffer where the data is to be sourced from
 * \param[in] DataLen     Length of the data to send
 * \param[in] ACLChannel  ACL channel information structure containing the destination channel's information, NULL
 *                        to send to the remote device's signaling channel
 *
 * \return A value from the \ref BT_SendPacket_ErrorCodes_t enum
 */
uint8_t Bluetooth_SendPacket(void* Data,
                             const uint16_t DataLen,
                             Bluetooth_Channel_t* const ACLChannel)
{
	BT_ACL_Header_t        ACLPacketHeader;
	BT_DataPacket_Header_t DataHeader;

	/* A remote device must be connected before a packet transmission is attempted */
	if (!(Bluetooth_Connection.IsConnected))
	  return BT_SENDPACKET_NotConnected;

	/* If the destination channel is not the signaling channel and it is not currently fully open, abort */
	if ((ACLChannel != NULL) && (ACLChannel->State != BT_Channel_Open))
	  return BT_SENDPACKET_ChannelNotOpen;

	/* Fill out the packet's header from the remote device connection information structure */
	ACLPacketHeader.ConnectionHandle      = (Bluetooth_Connection.ConnectionHandle | BT_ACL_FIRST_AUTOFLUSH);
	ACLPacketHeader.DataLength            = sizeof(DataHeader) + DataLen;
	DataHeader.PayloadLength              = DataLen;
	DataHeader.DestinationChannel         = (ACLChannel == NULL) ? BT_CHANNEL_SIGNALING : ACLChannel->RemoteNumber;

	Pipe_SelectPipe(BLUETOOTH_DATA_OUT_PIPE);

	Pipe_WaitUntilReady();
	Pipe_Unfreeze();

	/* Write the packet contents to the pipe so that it can be sent to the remote device */
	Pipe_Write_Stream_LE(&ACLPacketHeader, sizeof(ACLPacketHeader));
	Pipe_Write_Stream_LE(&DataHeader, sizeof(DataHeader));
	Pipe_Write_Stream_LE(Data, DataLen);
	Pipe_ClearOUT();

	Pipe_Freeze();

	BT_ACL_DEBUG(2, "");
	BT_ACL_DEBUG(2, "Packet Sent");
	BT_ACL_DEBUG(2, "-- Connection Handle: 0x%04X", (ACLPacketHeader.ConnectionHandle & 0x0FFF));
	BT_ACL_DEBUG(2, "-- Data Length: 0x%04X", ACLPacketHeader.DataLength);
	BT_ACL_DEBUG(2, "-- Destination Channel: 0x%04X", DataHeader.DestinationChannel);
	BT_ACL_DEBUG(2, "-- Payload Length: 0x%04X", DataHeader.PayloadLength);

	return BT_SENDPACKET_NoError;
}

uint8_t MIDI_Host_Flush(USB_ClassInfo_MIDI_Host_t* const MIDIInterfaceInfo)
{
	uint8_t portnum = MIDIInterfaceInfo->Config.PortNumber;
	uint8_t ErrorCode;
	if ((USB_HostState[portnum] != HOST_STATE_Configured) || !(MIDIInterfaceInfo->State.IsActive))
	  return PIPE_RWSTREAM_DeviceDisconnected;

	Pipe_SelectPipe(portnum,MIDIInterfaceInfo->Config.DataOUTPipeNumber);

	if (Pipe_BytesInPipe(portnum))
	{
		Pipe_ClearOUT(portnum);

		if ((ErrorCode = Pipe_WaitUntilReady(portnum)) != PIPE_READYWAIT_NoError)
		  return ErrorCode;
	}

	return PIPE_READYWAIT_NoError;
}

uint8_t MIDI_Host_Flush(USB_ClassInfo_MIDI_Host_t* const MIDIInterfaceInfo)
{
	if (USB_HostState != HOST_STATE_Configured)
	  return PIPE_RWSTREAM_DeviceDisconnected;
	
	uint8_t ErrorCode;

	Pipe_SelectPipe(MIDIInterfaceInfo->Config.DataOUTPipeNumber);

	if (Pipe_BytesInPipe())
	{
		Pipe_ClearOUT();

		if ((ErrorCode = Pipe_WaitUntilReady()) != PIPE_READYWAIT_NoError)
		  return ErrorCode;
	}

	return PIPE_READYWAIT_NoError;
}

uint8_t SI_Host_SendData(USB_ClassInfo_SI_Host_t* const SIInterfaceInfo,
                         void* Buffer,
                         const uint16_t Bytes)
{
	uint8_t ErrorCode;

	if ((USB_HostState != HOST_STATE_Configured) || !(SIInterfaceInfo->State.IsActive))
	  return PIPE_RWSTREAM_DeviceDisconnected;

	Pipe_SelectPipe(SIInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	ErrorCode = Pipe_Write_Stream_LE(Buffer, Bytes, NO_STREAM_CALLBACK);

	Pipe_ClearOUT();
	Pipe_Freeze();

	return ErrorCode;
}

/** Sends the given data directly to the printer via the data endpoints, for the sending of print commands in printer
 *  languages accepted by the attached printer (e.g. PCL).
 *
 *  \param[in] PrinterCommands  Pointer to the data to send to the attached printer
 *  \param[in] CommandSize  Size of the data to send to the attached printer
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
uint8_t Printer_SendData(const void* const PrinterCommands,
                         const uint16_t CommandSize)
{
	uint8_t ErrorCode;

	Pipe_SelectPipe(PRINTER_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(PrinterCommands, CommandSize, NULL)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	Pipe_ClearOUT();

	Pipe_WaitUntilReady();

	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}

/** ISR to handle the reloading of the endpoint with the next sample. */
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
{
	uint8_t PrevPipe = Pipe_GetCurrentPipe();

	Pipe_SelectPipe(AUDIO_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	/* Check if the current pipe can be written to (device ready for more data) */
	if (Pipe_IsOUTReady())
	{
		int16_t AudioSample;

		#if defined(USE_TEST_TONE)
			static uint8_t SquareWaveSampleCount;
			static int16_t CurrentWaveValue;

			/* In test tone mode, generate a square wave at 1/256 of the sample rate */
			if (SquareWaveSampleCount++ == 0xFF)
			  CurrentWaveValue ^= 0x8000;

			/* Only generate audio if the board button is being pressed */
			AudioSample = (Buttons_GetStatus() & BUTTONS_BUTTON1) ? CurrentWaveValue : 0;
		#else
			/* Audio sample is ADC value scaled to fit the entire range */
			AudioSample = ((SAMPLE_MAX_RANGE / ADC_MAX_RANGE) * ADC_GetResult());

			#if defined(MICROPHONE_BIASED_TO_HALF_RAIL)
			/* Microphone is biased to half rail voltage, subtract the bias from the sample value */
			AudioSample -= (SAMPLE_MAX_RANGE / 2);
			#endif
		#endif

		Pipe_Write_16_LE(AudioSample);
		Pipe_Write_16_LE(AudioSample);

		if (!(Pipe_IsReadWriteAllowed()))
		  Pipe_ClearOUT();
	}

	Pipe_Freeze();
	Pipe_SelectPipe(PrevPipe);
}

/** Function to send the given data to the device, after a command block has been issued.
 *
 *  \param[in] Buffer  Source data buffer to send to the device
 *  \param[in] Bytes   Number of bytes to send
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
uint8_t SImage_SendData(void* const Buffer,
                        const uint16_t Bytes)
{
	uint8_t ErrorCode;

	/* Unfreeze the data OUT pipe */
	Pipe_SelectPipe(SIMAGE_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	/* Write the data contents to the pipe */
	ErrorCode = Pipe_Write_Stream_LE(Buffer, Bytes, NULL);

	/* Send the last packet to the attached device */
	Pipe_ClearOUT();

	/* Freeze the pipe again after use */
	Pipe_Freeze();

	return ErrorCode;
}

/** Sends the given data directly to the printer via the data endpoints, for the sending of print commands in printer
 *  languages accepted by the attached printer (e.g. PCL).
 *
 *  \param[in] PrinterCommands  Pointer to the data to send to the attached printer
 *  \param[in] CommandSize  Size of the data to send to the attached printer
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
uint8_t Printer_SendData(const void* const PrinterCommands, const uint16_t CommandSize)
{
	uint8_t ErrorCode;

	Pipe_SelectPipe(PRINTER_DATA_OUT_PIPE);
	Pipe_Unfreeze();
	
	if ((ErrorCode = Pipe_Write_Stream_LE(PrinterCommands, CommandSize)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	Pipe_ClearOUT();
	while (!(Pipe_IsOUTReady()))
	{
		if (USB_HostState == HOST_STATE_Unattached)
		  return PIPE_RWSTREAM_DeviceDisconnected;
	}
	
	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}

/** Sends or receives the transaction's data stage to or from the attached device, reading or
 *  writing to the nominated buffer.
 *
 *  \param  BufferPtr  Pointer to the data buffer to read from or write to
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
static uint8_t MassStore_SendReceiveData(void* BufferPtr)
{
	uint8_t  ErrorCode = PIPE_RWSTREAM_NoError;
	uint16_t BytesRem  = SCSICommandBlock.Header.DataTransferLength;

	/* Check the direction of the SCSI command data stage */
	if (SCSICommandBlock.Header.Flags & COMMAND_DIRECTION_DATA_IN)
	{
		/* Select the IN data pipe for data reception */
		Pipe_SelectPipe(MASS_STORE_DATA_IN_PIPE);
		Pipe_Unfreeze();
		
		/* Read in the block data from the pipe */
		if ((ErrorCode = Pipe_Read_Stream_LE(BufferPtr, BytesRem)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Acknowledge the packet */
		Pipe_ClearIN();
	}
	else
	{
		/* Select the OUT data pipe for data transmission */
		Pipe_SelectPipe(MASS_STORE_DATA_OUT_PIPE);
		Pipe_Unfreeze();

		/* Write the block data to the pipe */
		if ((ErrorCode = Pipe_Write_Stream_LE(BufferPtr, BytesRem)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Acknowledge the packet */
		Pipe_ClearOUT();
		
		while (!(Pipe_IsOUTReady()));
	}
	
	/* Freeze used pipe after use */
	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}