C++ MX6_IO_ADDRESS函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中MX6_IO_ADDRESS函数的典型用法代码示例。如果您正苦于以下问题：C++ MX6_IO_ADDRESS函数的具体用法？C++ MX6_IO_ADDRESS怎么用？C++ MX6_IO_ADDRESS使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了MX6_IO_ADDRESS函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: mx6q_setup_weimcs

static void mx6q_setup_weimcs(void)
{
	unsigned int reg;
	void __iomem *nor_reg = MX6_IO_ADDRESS(WEIM_BASE_ADDR);
	void __iomem *ccm_reg = MX6_IO_ADDRESS(CCM_BASE_ADDR);

	/*CCM_BASE_ADDR + CLKCTL_CCGR6*/
	reg = readl(ccm_reg + 0x80);
	reg |= 0x00000C00;
	writel(reg, ccm_reg + 0x80);

	__raw_writel(0x00620081, nor_reg);
	__raw_writel(0x1C022000, nor_reg + 0x00000008);
	__raw_writel(0x0804a240, nor_reg + 0x00000010);
}

开发者ID:rogrady，项目名称:lin_imx6，代码行数:15，代码来源:board-mx6q_sabreauto.c

示例2: imx6q_sabreauto_init_usb

static void __init imx6q_sabreauto_init_usb(void)
{
	int ret = 0;
	imx_otg_base = MX6_IO_ADDRESS(MX6Q_USB_OTG_BASE_ADDR);

	ret = gpio_request(SABREAUTO_USB_OTG_OC, "otg-oc");
	if (ret) {
		printk(KERN_ERR"failed to get GPIO SABREAUTO_USB_OTG_OC:"
			" %d\n", ret);
		return;
	}
	gpio_direction_input(SABREAUTO_USB_OTG_OC);

	ret = gpio_request(SABREAUTO_USB_HOST1_OC, "usbh1-oc");
	if (ret) {
		printk(KERN_ERR"failed to get SABREAUTO_USB_HOST1_OC:"
			" %d\n", ret);
		return;
	}
	gpio_direction_input(SABREAUTO_USB_HOST1_OC);

	mxc_iomux_set_gpr_register(1, 13, 1, 0);
	mx6_set_otghost_vbus_func(imx6q_sabreauto_usbotg_vbus);
	mx6_usb_dr_init();
	mx6_set_host1_vbus_func(imx6q_sabreauto_usbhost1_vbus);
#ifdef CONFIG_USB_EHCI_ARC_HSIC
	mx6_usb_h2_init();
	mx6_usb_h3_init();
#endif
}

开发者ID:rogrady，项目名称:lin_imx6，代码行数:30，代码来源:board-mx6q_sabreauto.c

示例3: mx6_get_srev

static int mx6_get_srev(void)
{
	void __iomem *anatop = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
	u32 rev;
	if (cpu_is_mx6sl())
		rev = __raw_readl(anatop + MX6SL_USB_ANALOG_DIGPROG);
	else
		rev = __raw_readl(anatop + MX6_USB_ANALOG_DIGPROG);

	rev &= 0xff;

	if (rev == 0)
		return IMX_CHIP_REVISION_1_0;
	else if (rev == 1)
		return IMX_CHIP_REVISION_1_1;
	else if (rev == 2)
		return IMX_CHIP_REVISION_1_2;
	else if (rev == 3)
		return IMX_CHIP_REVISION_1_3;
	else if (rev == 4)
		return IMX_CHIP_REVISION_1_4;
	else if (rev == 5)
		return IMX_CHIP_REVISION_1_5;

	return IMX_CHIP_REVISION_UNKNOWN;
}

开发者ID:PDi-Communication-Systems-Inc，项目名称:kernel-imx，代码行数:26，代码来源:cpu.c

示例4: mx6_usb_h2_init

void __init mx6_usb_h2_init(void)
{
	struct platform_device *pdev, *pdev_wakeup;
	static void __iomem *anatop_base_addr = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
	usbh2_config.wakeup_pdata = &usbh2_wakeup_config;

	hsic_strobe_start_pad = cpu_is_mx6q() ? MX6Q_PAD_RGMII_TX_CTL__USBOH3_H2_STROBE_START :
			(cpu_is_mx6dl() ? MX6DL_PAD_RGMII_TX_CTL__USBOH3_H2_STROBE_START :
			(cpu_is_mx6sl() ? MX6SL_PAD_HSIC_STROBE__USB_H_STROBE_START : 0));

	if (cpu_is_mx6sl())
		pdev = imx6sl_add_fsl_ehci_hs(2, &usbh2_config);
	else
		pdev = imx6q_add_fsl_ehci_hs(2, &usbh2_config);

	usbh2_wakeup_config.usb_pdata[0] = pdev->dev.platform_data;
	if (cpu_is_mx6sl())
		pdev_wakeup = imx6sl_add_fsl_usb2_hs_wakeup(2, &usbh2_wakeup_config);
	else
		pdev_wakeup = imx6q_add_fsl_usb2_hs_wakeup(2, &usbh2_wakeup_config);
	platform_device_add(pdev);
	((struct fsl_usb2_platform_data *)(pdev->dev.platform_data))->wakeup_pdata =
		pdev_wakeup->dev.platform_data;
	/* Some phy and power's special controls for host2
	 * 1. Its 480M is from OTG's 480M
	 * 2. EN_USB_CLKS should always be opened
	 */
	__raw_writel(BM_ANADIG_USB1_PLL_480_CTRL_EN_USB_CLKS,
			anatop_base_addr + HW_ANADIG_USB1_PLL_480_CTRL_SET);
	/* must change the clkgate delay to 2 or 3 to avoid
	 * 24M OSCI clock not stable issue */
	__raw_writel(BF_ANADIG_ANA_MISC0_CLKGATE_DELAY(3),
			anatop_base_addr + HW_ANADIG_ANA_MISC0);
}

开发者ID:videologyincengineering，项目名称:TFMIPI_Kernel，代码行数:34，代码来源:usb_h2.c

示例5: imx6q_hdmidongle_init_usb

static void __init imx6q_hdmidongle_init_usb(void)
{
    int ret = 0;

    imx_otg_base = MX6_IO_ADDRESS(MX6Q_USB_OTG_BASE_ADDR);
    /* disable external charger detect,
     * or it will affect signal quality at dp .
     */
    ret = gpio_request(HDMIDONGLE_USB_OTG_PWR, "usb-pwr");
    if (ret) {
        pr_err("failed to get GPIO HDMIDONGLE_USB_OTG_PWR: %d\n",
               ret);
        return;
    }
    gpio_direction_output(HDMIDONGLE_USB_OTG_PWR, 0);
    /* keep USB host1 VBUS always on */
    if (board_is_mx6_reva()) {
        ret = gpio_request(HDMIDONGLE_USB_H1_PWR, "usb-h1-pwr");
        if (ret) {
            pr_err("failed to get GPIO HDMIDONGLE_USB_H1_PWR: %d\n",
                   ret);
            return;
        }
        gpio_direction_output(HDMIDONGLE_USB_H1_PWR, 1);
    }
    mxc_iomux_set_gpr_register(1, 13, 1, 1);

    mx6_set_otghost_vbus_func(imx6q_hdmidongle_usbotg_vbus);
}

开发者ID:RealDigitalMedia，项目名称:linux-shuttle，代码行数:29，代码来源:board-mx6q_hdmidongle.c

示例6: _wake_up_enable

static void _wake_up_enable(struct fsl_usb2_platform_data *pdata, bool enable)
{
    void __iomem *phy_reg = MX6_IO_ADDRESS(USB_PHY1_BASE_ADDR);

    pr_debug("host1, %s, enable is %d\n", __func__, enable);
    if (enable) {
        __raw_writel(BM_USBPHY_CTRL_ENIDCHG_WKUP | BM_USBPHY_CTRL_ENVBUSCHG_WKUP
                     | BM_USBPHY_CTRL_ENDPDMCHG_WKUP
                     | BM_USBPHY_CTRL_ENAUTOSET_USBCLKS
                     | BM_USBPHY_CTRL_ENAUTOCLR_PHY_PWD
                     | BM_USBPHY_CTRL_ENAUTOCLR_CLKGATE
                     | BM_USBPHY_CTRL_ENAUTOCLR_USBCLKGATE
                     | BM_USBPHY_CTRL_ENAUTO_PWRON_PLL , phy_reg + HW_USBPHY_CTRL_SET);
        USB_H1_CTRL |= (UCTRL_OWIE);
    } else {
        __raw_writel(BM_USBPHY_CTRL_ENIDCHG_WKUP | BM_USBPHY_CTRL_ENVBUSCHG_WKUP
                     | BM_USBPHY_CTRL_ENDPDMCHG_WKUP
                     | BM_USBPHY_CTRL_ENAUTOSET_USBCLKS
                     | BM_USBPHY_CTRL_ENAUTOCLR_PHY_PWD
                     | BM_USBPHY_CTRL_ENAUTOCLR_CLKGATE
                     | BM_USBPHY_CTRL_ENAUTOCLR_USBCLKGATE
                     | BM_USBPHY_CTRL_ENAUTO_PWRON_PLL , phy_reg + HW_USBPHY_CTRL_CLR);
        USB_H1_CTRL &= ~(UCTRL_OWIE);
        /* The interrupt must be disabled for at least 3
        * cycles of the standby clock(32k Hz) , that is 0.094 ms*/
        udelay(100);
    }
}

开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:28，代码来源:usb_h1.c

示例7: mx6_arm2_init_usb

static void __init mx6_arm2_init_usb(void)
{
	int ret = 0;

	imx_otg_base = MX6_IO_ADDRESS(MX6Q_USB_OTG_BASE_ADDR);

	/* disable external charger detect,
	 * or it will affect signal quality at dp.
	 */

	ret = gpio_request(MX6_BRD_USBOTG1_PWR, "usbotg-pwr");
	if (ret) {
		pr_err("failed to get GPIO MX6_BRD_USBOTG1_PWR:%d\n", ret);
		return;
	}
	gpio_direction_output(MX6_BRD_USBOTG1_PWR, 0);

	ret = gpio_request(MX6_BRD_USBOTG2_PWR, "usbh1-pwr");
	if (ret) {
		pr_err("failed to get GPIO MX6_BRD_USBOTG2_PWR:%d\n", ret);
		return;
	}
	gpio_direction_output(MX6_BRD_USBOTG2_PWR, 1);

	mx6_set_otghost_vbus_func(imx6_arm2_usbotg_vbus);
#ifdef CONFIG_USB_EHCI_ARC_HSIC
	mxc_iomux_set_specialbits_register(MX6SL_PAD_HSIC_DAT,
		PAD_CTL_DDR_SEL_DDR3, PAD_CTL_DDR_SEL_MASK);
	mxc_iomux_set_specialbits_register(MX6SL_PAD_HSIC_STROBE,
		PAD_CTL_DDR_SEL_DDR3, PAD_CTL_DDR_SEL_MASK);

	mx6_usb_h2_init();
#endif
}

开发者ID:develersrl，项目名称:winmate-kernel，代码行数:34，代码来源:board-mx6sl_arm2.c

示例8: mx6_evk_init_usb

static void __init mx6_evk_init_usb(void)
{
	int ret = 0;

	imx_otg_base = MX6_IO_ADDRESS(MX6Q_USB_OTG_BASE_ADDR);

	/* disable external charger detect,
	 * or it will affect signal quality at dp.
	 */

	ret = gpio_request(MX6_BRD_USBOTG1_PWR, "usbotg-pwr");
	if (ret) {
		pr_err("failed to get GPIO MX6_BRD_USBOTG1_PWR:%d\n", ret);
		return;
	}
	gpio_direction_output(MX6_BRD_USBOTG1_PWR, 0);

	ret = gpio_request(MX6_BRD_USBOTG2_PWR, "usbh1-pwr");
	if (ret) {
		pr_err("failed to get GPIO MX6_BRD_USBOTG2_PWR:%d\n", ret);
		return;
	}
	gpio_direction_output(MX6_BRD_USBOTG2_PWR, 1);

	mx6_set_otghost_vbus_func(imx6_evk_usbotg_vbus);
	mx6_usb_dr_init();
#ifdef CONFIG_USB_EHCI_ARC_HSIC
	mx6_usb_h2_init();
#endif
}

开发者ID:rogrady，项目名称:lin_imx6，代码行数:30，代码来源:board-mx6sl_evk.c

示例9: fsl_usb_host_init_ext

static int fsl_usb_host_init_ext(struct platform_device *pdev)
{
	static void __iomem *anatop_base_addr = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
	int ret;
	struct clk *usb_clk;

	/* The PLL's power and output to usb for host 1
	 * is totally controlled by IC, so the Software only needs
	 * to enable them at initializtion. */
	__raw_writel(BM_ANADIG_USB2_PLL_480_CTRL_BYPASS,
			anatop_base_addr + HW_ANADIG_USB2_PLL_480_CTRL_CLR);
	__raw_writel(BM_ANADIG_USB2_PLL_480_CTRL_ENABLE  \
			| BM_ANADIG_USB2_PLL_480_CTRL_POWER \
			| BM_ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS, \
			anatop_base_addr + HW_ANADIG_USB2_PLL_480_CTRL_SET);

	usb_clk = clk_get(NULL, "usboh3_clk");
	clk_enable(usb_clk);
	usb_oh3_clk = usb_clk;

	ret = fsl_usb_host_init(pdev);
	if (ret) {
		printk(KERN_ERR "host1 init fails......\n");
                clk_disable(usb_oh3_clk);
                clk_put(usb_oh3_clk);
		return ret;
	}
	usbh1_internal_phy_clock_gate(true);
	usb_phy_enable(pdev->dev.platform_data);

	return 0;
}

开发者ID:geekmaster，项目名称:kindle-pw3-kernel，代码行数:32，代码来源:usb_h1.c

示例10: post_cpu_init

static int __init post_cpu_init(void)
{
	unsigned int reg;
	void __iomem *base;

	iram_init(MX6Q_IRAM_BASE_ADDR, MX6Q_IRAM_SIZE);

	base = ioremap(AIPS1_ON_BASE_ADDR, PAGE_SIZE);
	__raw_writel(0x0, base + 0x40);
	__raw_writel(0x0, base + 0x44);
	__raw_writel(0x0, base + 0x48);
	__raw_writel(0x0, base + 0x4C);
	reg = __raw_readl(base + 0x50) & 0x00FFFFFF;
	__raw_writel(reg, base + 0x50);
	iounmap(base);

	base = ioremap(AIPS2_ON_BASE_ADDR, PAGE_SIZE);
	__raw_writel(0x0, base + 0x40);
	__raw_writel(0x0, base + 0x44);
	__raw_writel(0x0, base + 0x48);
	__raw_writel(0x0, base + 0x4C);
	reg = __raw_readl(base + 0x50) & 0x00FFFFFF;
	__raw_writel(reg, base + 0x50);
	iounmap(base);

	if (enable_wait_mode) {
		/* Allow SCU_CLK to be disabled when all cores are in WFI*/
		base = IO_ADDRESS(SCU_BASE_ADDR);
		reg = __raw_readl(base);
		reg |= 0x20;
		__raw_writel(reg, base);
	}

	/* Disable SRC warm reset to work aound system reboot issue */
	base = IO_ADDRESS(SRC_BASE_ADDR);
	reg = __raw_readl(base);
	reg &= ~0x1;
	__raw_writel(reg, base);

	gpc_base = MX6_IO_ADDRESS(GPC_BASE_ADDR);
	ccm_base = MX6_IO_ADDRESS(CCM_BASE_ADDR);

	num_cpu_idle_lock = 0x0;

	init_mmdc_settings();
	return 0;
}

开发者ID:boseji，项目名称:kernel_imx，代码行数:47，代码来源:cpu.c

示例11: mx6_usb_h1_init

static int  __init mx6_usb_h1_init(void)
{
    static void __iomem *anatop_base_addr = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
    struct imx_fsl_usb2_wakeup_data imx6q_fsl_hs_wakeup_data[] = {
        imx_fsl_usb2_wakeup_data_entry_single(MX6Q, 1, HS1)
    };
    struct imx_fsl_usb2_wakeup_data  imx6sl_fsl_hs_wakeup_data[] = {
        imx_fsl_usb2_wakeup_data_entry_single(MX6SL, 1, HS1)
    };
    struct imx_mxc_ehci_data imx6q_mxc_ehci_hs_data[] = {
        imx_mxc_ehci_data_entry_single(MX6Q, 1, HS1)
    };
    struct imx_mxc_ehci_data imx6sl_mxc_ehci_hs_data[] = {
        imx_mxc_ehci_data_entry_single(MX6SL, 1, HS1)
    };

    mx6_get_host1_vbus_func(&mx6_set_usb_host1_vbus);
    if (mx6_set_usb_host1_vbus)
        mx6_set_usb_host1_vbus(true);

    /* Some phy and power's special controls for host1
     * 1. The external charger detector needs to be disabled
     * or the signal at DP will be poor
     * 2. The PLL's power and output to usb for host 1
     * is totally controlled by IC, so the Software only needs
     * to enable them at initializtion.
     */
    __raw_writel(BM_ANADIG_USB2_CHRG_DETECT_EN_B  \
                 | BM_ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B, \
                 anatop_base_addr + HW_ANADIG_USB2_CHRG_DETECT);
    __raw_writel(BM_ANADIG_USB2_PLL_480_CTRL_BYPASS,
                 anatop_base_addr + HW_ANADIG_USB2_PLL_480_CTRL_CLR);
    __raw_writel(BM_ANADIG_USB2_PLL_480_CTRL_ENABLE  \
                 | BM_ANADIG_USB2_PLL_480_CTRL_POWER \
                 | BM_ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS, \
                 anatop_base_addr + HW_ANADIG_USB2_PLL_480_CTRL_SET);

    usbh1_config.wakeup_pdata = &usbh1_wakeup_config;
    if (usb_icbug_swfix_need()) {
        usbh1_config.platform_rh_suspend = usbh1_platform_rh_suspend_swfix;
        usbh1_config.platform_rh_resume  = usbh1_platform_rh_resume_swfix;
    } else {
        usbh1_config.platform_rh_suspend = usbh1_platform_rh_suspend;
        usbh1_config.platform_rh_resume  = usbh1_platform_rh_resume;
    }
    if (cpu_is_mx6sl())
        pdev = imx6sl_add_fsl_ehci_hs(1, &usbh1_config);
    else
        pdev = imx6q_add_fsl_ehci_hs(1, &usbh1_config);
    usbh1_wakeup_config.usb_pdata[0] = pdev->dev.platform_data;
    if (cpu_is_mx6sl())
        pdev_wakeup = imx6sl_add_fsl_usb2_hs_wakeup(1, &usbh1_wakeup_config);
    else
        pdev_wakeup = imx6q_add_fsl_usb2_hs_wakeup(1, &usbh1_wakeup_config);
    platform_device_add(pdev);
    ((struct fsl_usb2_platform_data *)(pdev->dev.platform_data))->wakeup_pdata =
        (struct fsl_usb2_wakeup_platform_data *)(pdev_wakeup->dev.platform_data);
    return 0;
}

开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:59，代码来源:usb_h1.c

示例12: usbh1_internal_phy_clock_gate

static void usbh1_internal_phy_clock_gate(bool on)
{
    void __iomem *phy_reg = MX6_IO_ADDRESS(USB_PHY1_BASE_ADDR);
    if (on) {
        __raw_writel(BM_USBPHY_CTRL_CLKGATE, phy_reg + HW_USBPHY_CTRL_CLR);
    } else {
        __raw_writel(BM_USBPHY_CTRL_CLKGATE, phy_reg + HW_USBPHY_CTRL_SET);
    }
}

开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:9，代码来源:usb_h1.c

示例13: mx6_snvs_poweroff

static void mx6_snvs_poweroff(void)
{
	u32 value;
	void __iomem *mx6_snvs_base = MX6_IO_ADDRESS(MX6Q_SNVS_BASE_ADDR);

	value = readl(mx6_snvs_base + SNVS_LPCR);
	/* set TOP and DP_EN bit */
	writel(value | 0x60, mx6_snvs_base + SNVS_LPCR);
}

开发者ID:rogrady，项目名称:lin_imx6，代码行数:9，代码来源:board-mx6sl_evk.c

示例14: usbh1_platform_rh_suspend

static void usbh1_platform_rh_suspend(struct fsl_usb2_platform_data *pdata)
{
    /*for mx6sl ,we do not need any sw fix*/
    if (cpu_is_mx6sl())
        return ;
    __raw_writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
                 MX6_IO_ADDRESS(pdata->phy_regs)
                 + HW_USBPHY_CTRL_CLR);
}

开发者ID:brunotl，项目名称:kernel-kobo-mx6sl-ntx，代码行数:9，代码来源:usb_h1.c

示例15: usbh1_wakeup_event_clear

static void usbh1_wakeup_event_clear(void)
{
	void __iomem *phy_reg = MX6_IO_ADDRESS(USB_PHY1_BASE_ADDR);
	u32 wakeup_irq_bits;

	wakeup_irq_bits = BM_USBPHY_CTRL_RESUME_IRQ | BM_USBPHY_CTRL_WAKEUP_IRQ;
	if (__raw_readl(phy_reg + HW_USBPHY_CTRL) && wakeup_irq_bits) {
		/* clear the wakeup interrupt status */
		__raw_writel(wakeup_irq_bits, phy_reg + HW_USBPHY_CTRL_CLR);
	}
}

开发者ID:panfudonmx6q，项目名称:imx6q_fsl，代码行数:11，代码来源:usb_h1.c

示例16: imx6q_seco_UDOO_init_usb

static void __init imx6q_seco_UDOO_init_usb(void) {

	imx_otg_base = MX6_IO_ADDRESS(MX6Q_USB_OTG_BASE_ADDR);
	/* disable external charger detect,
	 * or it will affect signal quality at dp .
	 */
	mxc_iomux_set_gpr_register(1, 13, 1, 1);

	mx6_set_otghost_vbus_func(imx6q_seco_UDOO_usbotg_vbus);
//	mx6_usb_dr_init();
//	mx6_usb_h1_init();
}

开发者ID:jaketesler，项目名称:UDOO_Kernel，代码行数:12，代码来源:board-mx6_seco_UDOO.c

示例17: fsl_usb_host_uninit_ext

static void fsl_usb_host_uninit_ext(struct platform_device *pdev)
{
	struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
	void __iomem *anatop_base_addr = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
	fsl_usb_host_uninit(pdata);

	clk_disable(usb_oh3_clk);
	clk_put(usb_oh3_clk);
	usb_stop_mode_lock();
	if (usb_stop_mode_refcount(false) == 0)
		__raw_writel(BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG, anatop_base_addr + HW_ANADIG_ANA_MISC0_CLR);
	usb_stop_mode_unlock();
}

开发者ID:panfudonmx6q，项目名称:imx6q_fsl，代码行数:13，代码来源:usb_h1.c

示例18: mx6_usb_h1_init

static int  __init mx6_usb_h1_init(void)
{
	static void __iomem *anatop_base_addr = MX6_IO_ADDRESS(ANATOP_BASE_ADDR);
	struct imx_fsl_usb2_wakeup_data imx6q_fsl_hs_wakeup_data[] = {
		imx_fsl_usb2_wakeup_data_entry_single(MX6Q, 1, HS1)};
	struct imx_fsl_usb2_wakeup_data  imx6sl_fsl_hs_wakeup_data[] = {
		imx_fsl_usb2_wakeup_data_entry_single(MX6SL, 1, HS1)};
	struct imx_mxc_ehci_data imx6q_mxc_ehci_hs_data[] = {
		imx_mxc_ehci_data_entry_single(MX6Q, 1, HS1)};
	struct imx_mxc_ehci_data imx6sl_mxc_ehci_hs_data[] = {
		imx_mxc_ehci_data_entry_single(MX6SL, 1, HS1)};

	mx6_get_host1_vbus_func(&mx6_set_usb_host1_vbus);
	usbh1_config.platform_driver_vbus = mx6_set_usb_host1_vbus;

	/* The external charger detector needs to be disabled
	 * or the signal at DP will be poor
	 */
	__raw_writel(BM_ANADIG_USB2_CHRG_DETECT_EN_B  \
			| BM_ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B, \
			anatop_base_addr + HW_ANADIG_USB2_CHRG_DETECT);
	/* Turn off PHY PLL until USB host driver is loaded */
	__raw_writel(BM_ANADIG_USB2_PLL_480_CTRL_BYPASS,
			anatop_base_addr + HW_ANADIG_USB2_PLL_480_CTRL_SET);
	__raw_writel(BM_ANADIG_USB2_PLL_480_CTRL_ENABLE  \
			| BM_ANADIG_USB2_PLL_480_CTRL_POWER \
			| BM_ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS, \
			anatop_base_addr + HW_ANADIG_USB2_PLL_480_CTRL_CLR);

	usbh1_config.wakeup_pdata = &usbh1_wakeup_config;
	if (usb_icbug_swfix_need()) {
		usbh1_config.platform_rh_suspend = usbh1_platform_rh_suspend_swfix;
		usbh1_config.platform_rh_resume  = usbh1_platform_rh_resume_swfix;
	} else {
		usbh1_config.platform_rh_suspend = usbh1_platform_rh_suspend;
		usbh1_config.platform_rh_resume  = usbh1_platform_rh_resume;
	}
	if (cpu_is_mx6sl())
		pdev = imx6sl_add_fsl_ehci_hs(1, &usbh1_config);
	else
		pdev = imx6q_add_fsl_ehci_hs(1, &usbh1_config);
	usbh1_wakeup_config.usb_pdata[0] = pdev->dev.platform_data;
	if (cpu_is_mx6sl())
		pdev_wakeup = imx6sl_add_fsl_usb2_hs_wakeup(1, &usbh1_wakeup_config);
	else
		pdev_wakeup = imx6q_add_fsl_usb2_hs_wakeup(1, &usbh1_wakeup_config);
	platform_device_add(pdev);
	((struct fsl_usb2_platform_data *)(pdev->dev.platform_data))->wakeup_pdata =
		(struct fsl_usb2_wakeup_platform_data *)(pdev_wakeup->dev.platform_data);
	return 0;
}

开发者ID:geekmaster，项目名称:kindle-pw3-kernel，代码行数:51，代码来源:usb_h1.c

示例19: usb_phy_enable

static int usb_phy_enable(struct fsl_usb2_platform_data *pdata)
{
	u32 tmp;
	void __iomem *phy_reg = MX6_IO_ADDRESS(USB_PHY1_BASE_ADDR);
	void __iomem *phy_ctrl;

	/* Stop then Reset */
	UH1_USBCMD &= ~UCMD_RUN_STOP;
	while (UH1_USBCMD & UCMD_RUN_STOP)
		;

	UH1_USBCMD |= UCMD_RESET;
	while ((UH1_USBCMD) & (UCMD_RESET))
		;

	/*
	 * If the controller reset does not put the PHY be out of
	 * low power mode, do it manually.
	 */
	if (UH1_PORTSC1 & PORTSC_PHCD) {
		UH1_PORTSC1 &= ~PORTSC_PHCD;
		mdelay(1);
	}

	/* Reset USBPHY module */
	phy_ctrl = phy_reg + HW_USBPHY_CTRL;
	tmp = __raw_readl(phy_ctrl);
	tmp |= BM_USBPHY_CTRL_SFTRST;
	__raw_writel(tmp, phy_ctrl);
	udelay(10);

	/* Remove CLKGATE and SFTRST */
	tmp = __raw_readl(phy_ctrl);
	tmp &= ~(BM_USBPHY_CTRL_CLKGATE | BM_USBPHY_CTRL_SFTRST);
	__raw_writel(tmp, phy_ctrl);
	udelay(10);

	/* Power up the PHY */
	__raw_writel(0, phy_reg + HW_USBPHY_PWD);
	/* enable FS/LS device */
	tmp = __raw_readl(phy_reg + HW_USBPHY_CTRL);
	tmp |= (BM_USBPHY_CTRL_ENUTMILEVEL2 | BM_USBPHY_CTRL_ENUTMILEVEL3);
	__raw_writel(tmp, phy_reg + HW_USBPHY_CTRL);

	if (!usb_icbug_swfix_need())
		__raw_writel((1 << 17), phy_reg + HW_USBPHY_IP_SET);
	if (cpu_is_mx6sl())
		__raw_writel((1 << 18), phy_reg + HW_USBPHY_IP_SET);
	return 0;
}

开发者ID:geekmaster，项目名称:kindle-pw3-kernel，代码行数:50，代码来源:usb_h1.c

示例20: fsl_platform_set_usb_phy_dis

/* enable/disable high-speed disconnect detector of phy ctrl */
void fsl_platform_set_usb_phy_dis(struct fsl_usb2_platform_data *pdata,
				  bool enable)
{
	u32 usb_phy_ctrl_dcdt = 0;
	/* for HSIC, we do not need to enable disconnect detection */
	if (pdata->phy_mode == FSL_USB2_PHY_HSIC)
		return;
	usb_phy_ctrl_dcdt = __raw_readl(
			MX6_IO_ADDRESS(pdata->phy_regs) + HW_USBPHY_CTRL) &
			BM_USBPHY_CTRL_ENHOSTDISCONDETECT;
	if (enable) {
		if (usb_phy_ctrl_dcdt == 0)
			__raw_writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
				MX6_IO_ADDRESS(pdata->phy_regs)
				+ HW_USBPHY_CTRL_SET);
	} else {
		if (usb_phy_ctrl_dcdt
				== BM_USBPHY_CTRL_ENHOSTDISCONDETECT)
			__raw_writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
				MX6_IO_ADDRESS(pdata->phy_regs)
				+ HW_USBPHY_CTRL_CLR);
	}
}

开发者ID:alinlazar，项目名称:utilite，代码行数:24，代码来源:usb_common.c

注：本文中的MX6_IO_ADDRESS函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ MX_BIN函数代码示例发布时间：2022-05-30

C++ MV_REG_WRITE函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19245|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：10003|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8333|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8702|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8648|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9674|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8634|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8007|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8670|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7541|2022-11-06

客服电话

电子邮件

C++ MX6_IO_ADDRESS函数代码示例

示例1: mx6q_setup_weimcs

示例2: imx6q_sabreauto_init_usb

示例3: mx6_get_srev

示例4: mx6_usb_h2_init

示例5: imx6q_hdmidongle_init_usb

示例6: _wake_up_enable

示例7: mx6_arm2_init_usb

示例8: mx6_evk_init_usb

示例9: fsl_usb_host_init_ext

示例10: post_cpu_init

示例11: mx6_usb_h1_init

示例12: usbh1_internal_phy_clock_gate

示例13: mx6_snvs_poweroff

示例14: usbh1_platform_rh_suspend

示例15: usbh1_wakeup_event_clear

示例16: imx6q_seco_UDOO_init_usb

示例17: fsl_usb_host_uninit_ext

示例18: mx6_usb_h1_init

示例19: usb_phy_enable

示例20: fsl_platform_set_usb_phy_dis

请发表评论

全部评论

上一篇：

下一篇：

CVE-2022-23003

小程序-跳转页面的方法及坑

krishnaik06/Machine-Learning-in-90-days

armancodv/building-energy-model-matlab:

美元符号为什么是“$”

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053