C++ IO_TAG函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中IO_TAG函数的典型用法代码示例。如果您正苦于以下问题：C++ IO_TAG函数的具体用法？C++ IO_TAG怎么用？C++ IO_TAG使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了IO_TAG函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: RCC_ClockCmd

uartPort_t *serialUART5(uint32_t baudRate, portMode_t mode, portOptions_t options)
{
    uartPort_t *s;
    static volatile uint8_t rx5Buffer[UART5_RX_BUFFER_SIZE];
    static volatile uint8_t tx5Buffer[UART5_TX_BUFFER_SIZE];
    NVIC_InitTypeDef NVIC_InitStructure;

    s = &uartPort5;
    s->port.vTable = uartVTable;

    s->port.baudRate = baudRate;

    s->port.rxBufferSize = UART5_RX_BUFFER_SIZE;
    s->port.txBufferSize = UART5_TX_BUFFER_SIZE;
    s->port.rxBuffer = rx5Buffer;
    s->port.txBuffer = tx5Buffer;

    s->USARTx = UART5;

    RCC_ClockCmd(RCC_APB1(UART5), ENABLE);

    serialUARTInit(IOGetByTag(IO_TAG(UART5_TX_PIN)), IOGetByTag(IO_TAG(UART5_RX_PIN)), mode, options, GPIO_AF_5, 5);

    NVIC_InitStructure.NVIC_IRQChannel = UART5_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = NVIC_PRIORITY_BASE(NVIC_PRIO_SERIALUART5);
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = NVIC_PRIORITY_SUB(NVIC_PRIO_SERIALUART5);
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    return s;
}

开发者ID:rayone，项目名称:betaflight-1，代码行数:31，代码来源:serial_uart_stm32f30x.c

示例2: pgResetFn_adcConfig

void pgResetFn_adcConfig(adcConfig_t *adcConfig)
{
    adcConfig->device = ADC_DEV_TO_CFG(adcDeviceByInstance(ADC_INSTANCE));

#ifdef VBAT_ADC_PIN
    adcConfig->vbat.enabled = true;
    adcConfig->vbat.ioTag = IO_TAG(VBAT_ADC_PIN);
#endif

#ifdef EXTERNAL1_ADC_PIN
    adcConfig->external1.enabled = true;
    adcConfig->external1.ioTag = IO_TAG(EXTERNAL1_ADC_PIN);
#endif

#ifdef CURRENT_METER_ADC_PIN
    adcConfig->current.enabled = true;
    adcConfig->current.ioTag = IO_TAG(CURRENT_METER_ADC_PIN);
#endif

#ifdef RSSI_ADC_PIN
    adcConfig->rssi.enabled = true;
    adcConfig->rssi.ioTag = IO_TAG(RSSI_ADC_PIN);
#endif

}

开发者ID:4712，项目名称:cleanflight，代码行数:25，代码来源:adc.c

示例3: resetSonarConfig

void resetSonarConfig(sonarConfig_t *sonarConfig)
{
#if defined(SONAR_TRIGGER_PIN) && defined(SONAR_ECHO_PIN)
    sonarConfig->triggerTag = IO_TAG(SONAR_TRIGGER_PIN);
    sonarConfig->echoTag = IO_TAG(SONAR_ECHO_PIN);
#else
#error Sonar not defined for target
#endif
}

开发者ID:kc10kevin，项目名称:betaflight，代码行数:9，代码来源:config.c

示例4: IOInit

serialPort_t *usbVcpOpen(void)
{
    vcpPort_t *s;

    IOInit(IOGetByTag(IO_TAG(PA11)), OWNER_USB, 0);
    IOInit(IOGetByTag(IO_TAG(PA12)), OWNER_USB, 0);

#if defined(STM32F4)
    usbGenerateDisconnectPulse();

    switch (usbDevConfig()->type) {
#ifdef USE_USB_CDC_HID
    case COMPOSITE:
        USBD_Init(&USB_OTG_dev, USB_OTG_FS_CORE_ID, &USR_desc, &USBD_HID_CDC_cb, &USR_cb);
        break;
#endif
    default:
        USBD_Init(&USB_OTG_dev, USB_OTG_FS_CORE_ID, &USR_desc, &USBD_CDC_cb, &USR_cb);
        break;
    }
#elif defined(STM32F7)
    usbGenerateDisconnectPulse();

    /* Init Device Library */
    USBD_Init(&USBD_Device, &VCP_Desc, 0);

    /* Add Supported Class */
    switch (usbDevConfig()->type) {
#ifdef USE_USB_CDC_HID
    case COMPOSITE:
    	USBD_RegisterClass(&USBD_Device, USBD_HID_CDC_CLASS);
        break;
#endif
    default:
        USBD_RegisterClass(&USBD_Device, USBD_CDC_CLASS);
        break;
    }

    /* HID Interface doesn't have any callbacks... */
    /* Add CDC Interface Class */
    USBD_CDC_RegisterInterface(&USBD_Device, &USBD_CDC_fops);

    /* Start Device Process */
    USBD_Start(&USBD_Device);
#else
    Set_System();
    Set_USBClock();
    USB_Init();
    USB_Interrupts_Config();
#endif

    s = &vcpPort;
    s->port.vTable = usbVTable;

    return (serialPort_t *)s;
}

开发者ID:4712betaflight，项目名称:betaflight，代码行数:56，代码来源:serial_usb_vcp.c

示例5: i2cInit

void i2cInit(I2CDevice device)
{
    UNUSED(device);

    scl = IOGetByTag(IO_TAG(SOFT_I2C_SCL));
    sda = IOGetByTag(IO_TAG(SOFT_I2C_SDA));

    IOConfigGPIO(scl, IOCFG_OUT_OD);
    IOConfigGPIO(sda, IOCFG_OUT_OD);
}

开发者ID:NZFez，项目名称:betaflight，代码行数:10，代码来源:bus_i2c_soft.c

示例6: mma8451ConfigureInterrupt

static inline void mma8451ConfigureInterrupt(void)
{
#ifdef MMA8451_INT_PIN
    IOInit(IOGetByTag(IO_TAG(MMA8451_INT_PIN)), OWNER_MPU_EXTI, 0);
    // TODO - maybe pullup / pulldown ?
    IOConfigGPIO(IOGetByTag(IO_TAG(MMA8451_INT_PIN)), IOCFG_IN_FLOATING); 
#endif

    i2cWrite(MPU_I2C_INSTANCE, MMA8452_ADDRESS, MMA8452_CTRL_REG3, MMA8452_CTRL_REG3_IPOL); // Interrupt polarity (active HIGH)
    i2cWrite(MPU_I2C_INSTANCE, MMA8452_ADDRESS, MMA8452_CTRL_REG4, MMA8452_CTRL_REG4_INT_EN_DRDY); // Enable DRDY interrupt (unused by this driver)
    i2cWrite(MPU_I2C_INSTANCE, MMA8452_ADDRESS, MMA8452_CTRL_REG5, 0); // DRDY routed to INT2
}

开发者ID:basdelfos，项目名称:betaflight，代码行数:12，代码来源:accgyro_mma845x.c

示例7: updateHardwareRevision

void updateHardwareRevision(void)
{
    if (hardwareRevision != BJF4_REV2) {
        return;
    }
    
    /* 
        if flash exists on PB3 then Rev1
    */
    if (m25p16_init(IO_TAG(PB3))) {
        hardwareRevision = BJF4_REV1;
    } else {
        IOInit(IOGetByTag(IO_TAG(PB3)), OWNER_FREE, RESOURCE_NONE, 0);
    }
}

开发者ID:mmiers，项目名称:betaflight，代码行数:15，代码来源:hardware_revision.c

示例8: selectMPUIntExtiConfigByHardwareRevision

ioTag_t selectMPUIntExtiConfigByHardwareRevision(void)
{

#ifdef AFROMINI
    return IO_TAG(PC13);
#else
    if (hardwareRevision < NAZE32_REV5) {
        // MPU_INT output on rev4 PB13
        return IO_TAG(PB13);
    } else {
        // MPU_INT output on rev5 PC13
        return IO_TAG(PC13);
    }
#endif
}

开发者ID:basdelfos，项目名称:betaflight，代码行数:15，代码来源:hardware_revision.c

示例9: targetConfiguration

// alternative defaults settings for BlueJayF4 targets
void targetConfiguration(void)
{
    if (hardwareRevision == BJF4_REV1 || hardwareRevision == BJF4_REV2) {
        gyroDeviceConfigMutable(0)->align = CW180_DEG;
        beeperDevConfigMutable()->ioTag = IO_TAG(BEEPER_OPT);
    }

    if (hardwareRevision == BJF4_MINI_REV3A || hardwareRevision == BJF4_REV1) {
        blackboxConfigMutable()->device = BLACKBOX_DEVICE_NONE;
    }

    if (hardwareRevision == BJF4_MINI_REV3A) {
        adcConfigMutable()->vbat.ioTag = IO_TAG(PA4);
    }
}

开发者ID:4712betaflight，项目名称:betaflight，代码行数:16，代码来源:config.c

示例10: detectSpiDevice

uint8_t detectSpiDevice(void)
{
#ifdef NAZE_SPI_CS_PIN
    nazeSpiCsPin = IOGetByTag(IO_TAG(NAZE_SPI_CS_PIN));
#endif

    uint8_t out[] = { M25P16_INSTRUCTION_RDID, 0, 0, 0 };
    uint8_t in[4];
    uint32_t flash_id;

    // try autodetect flash chip
    delay(50); // short delay required after initialisation of SPI device instance.
    ENABLE_SPI_CS;
    spiTransfer(NAZE_SPI_INSTANCE, in, out, sizeof(out));
    DISABLE_SPI_CS;

    flash_id = in[1] << 16 | in[2] << 8 | in[3];
    if (flash_id == FLASH_M25P16_ID)
        return SPI_DEVICE_FLASH;


    // try autodetect MPU
    delay(50);
    ENABLE_SPI_CS;
    spiTransferByte(NAZE_SPI_INSTANCE, MPU_RA_WHO_AM_I | MPU6500_BIT_RESET);
    in[0] = spiTransferByte(NAZE_SPI_INSTANCE, 0xff);
    DISABLE_SPI_CS;

    if (in[0] == MPU6500_WHO_AM_I_CONST)
        return SPI_DEVICE_MPU;

    return SPI_DEVICE_NONE;
}

开发者ID:basdelfos，项目名称:betaflight，代码行数:33，代码来源:hardware_revision.c

示例11: max7456Init

void max7456Init(const vcdProfile_t *pVcdProfile)
{
#ifdef MAX7456_SPI_CS_PIN
    max7456CsPin = IOGetByTag(IO_TAG(MAX7456_SPI_CS_PIN));
#endif
    IOInit(max7456CsPin, OWNER_OSD_CS, 0);
    IOConfigGPIO(max7456CsPin, SPI_IO_CS_CFG);

    spiSetDivisor(MAX7456_SPI_INSTANCE, SPI_CLOCK_STANDARD);
    // force soft reset on Max7456
    ENABLE_MAX7456;
    max7456Send(MAX7456ADD_VM0, MAX7456_RESET);
    DISABLE_MAX7456;

    // Setup values to write to registers
    videoSignalCfg = pVcdProfile->video_system;
    hosRegValue = 32 - pVcdProfile->h_offset;
    vosRegValue = 16 - pVcdProfile->v_offset;

#ifdef MAX7456_DMA_CHANNEL_TX
    dmaSetHandler(MAX7456_DMA_IRQ_HANDLER_ID, max7456_dma_irq_handler, NVIC_PRIO_MAX7456_DMA, 0);
#endif

    // Real init will be made later when driver detect idle.
}

开发者ID:DTFUHF，项目名称:betaflight，代码行数:25，代码来源:max7456.c

示例12: m25p16_init

/**
 * Initialize the driver, must be called before any other routines.
 *
 * Attempts to detect a connected m25p16. If found, true is returned and device capacity can be fetched with
 * m25p16_getGeometry().
 */
bool m25p16_init(ioTag_t csTag)
{
    /*
        if we have already detected a flash device we can simply exit

        TODO: change the init param in favour of flash CFG when ParamGroups work is done
        then cs pin can be specified in hardware_revision.c or config.c (dependent on revision).
    */
    if (geometry.sectors) {
        return true;
    }

    if (csTag) {
        m25p16CsPin = IOGetByTag(csTag);
    } else {
#ifdef M25P16_CS_PIN
        m25p16CsPin = IOGetByTag(IO_TAG(M25P16_CS_PIN));
#else
        return false;
#endif
    }
    IOInit(m25p16CsPin, OWNER_FLASH_CS, 0);
    IOConfigGPIO(m25p16CsPin, SPI_IO_CS_CFG);

    DISABLE_M25P16;

#ifndef M25P16_SPI_SHARED
    //Maximum speed for standard READ command is 20mHz, other commands tolerate 25mHz
    spiSetDivisor(M25P16_SPI_INSTANCE, SPI_CLOCK_FAST);
#endif

    return m25p16_readIdentification();
}

开发者ID:AlienWiiBF，项目名称:betaflight，代码行数:39，代码来源:flash_m25p16.c

示例13: sdcardInsertionDetectDeinit

void sdcardInsertionDetectDeinit(void)
{
#ifdef SDCARD_DETECT_PIN
    sdCardDetectPin = IOGetByTag(IO_TAG(SDCARD_DETECT_PIN));
    IOInit(sdCardDetectPin, OWNER_FREE, RESOURCE_NONE, 0);
    IOConfigGPIO(sdCardDetectPin, IOCFG_IN_FLOATING); 
#endif
}

开发者ID:Liquidas，项目名称:betaflight，代码行数:8，代码来源:sdcard.c

示例14: targetConfiguration

// alternative defaults settings for BlueJayF4 targets
void targetConfiguration(master_t *config)
{
    if (hardwareRevision == BJF4_REV1 || hardwareRevision == BJF4_REV2) {
        config->sensorAlignmentConfig.gyro_align = CW180_DEG;
        config->sensorAlignmentConfig.acc_align  = CW180_DEG;
        config->beeperConfig.ioTag = IO_TAG(BEEPER_OPT);
    }
}

开发者ID:mmiers，项目名称:betaflight，代码行数:9，代码来源:config.c

示例15: sdcardInsertionDetectInit

void sdcardInsertionDetectInit(void)
{
#ifdef SDCARD_DETECT_PIN
    sdCardDetectPin = IOGetByTag(IO_TAG(SDCARD_DETECT_PIN));
    IOInit(sdCardDetectPin, OWNER_SDCARD, RESOURCE_INPUT, 0);
    IOConfigGPIO(sdCardDetectPin, IOCFG_IPU); 
#endif
}

开发者ID:Liquidas，项目名称:betaflight，代码行数:8，代码来源:sdcard.c

示例16: pgResetFn_flashConfig

void pgResetFn_flashConfig(flashConfig_t *flashConfig)
{
#ifdef M25P16_CS_PIN
    flashConfig->csTag = IO_TAG(M25P16_CS_PIN);
#else
    flashConfig->csTag = IO_TAG_NONE;
#endif
    flashConfig->spiDevice = SPI_DEV_TO_CFG(spiDeviceByInstance(M25P16_SPI_INSTANCE));
}

开发者ID:rotcehdnih，项目名称:betaflight，代码行数:9，代码来源:flash.c

示例17: usbCableDetectInit

void usbCableDetectInit(void)
{
#ifdef USB_DETECT_PIN
    usbDetectPin = IOGetByTag(IO_TAG(USB_DETECT_PIN));

    IOInit(usbDetectPin, OWNER_USB_DETECT, 0);
    IOConfigGPIO(usbDetectPin, IOCFG_OUT_PP);
#endif
}

开发者ID:AlienWiiBF，项目名称:betaflight，代码行数:9，代码来源:usb_detection.c

示例18: rxSpiDeviceInit

void rxSpiDeviceInit(rx_spi_type_e spiType)
{
    static bool hardwareInitialised = false;

    if (hardwareInitialised) {
        return;
    }

#ifdef USE_RX_SOFTSPI
    if (spiType == RX_SPI_SOFTSPI) {
        useSoftSPI = true;
        softSpiInit(&softSPIDevice);
    }
    const SPIDevice rxSPIDevice = SOFT_SPIDEV_1;
#else
    UNUSED(spiType);
    const SPIDevice rxSPIDevice = spiDeviceByInstance(RX_SPI_INSTANCE);
    IOInit(IOGetByTag(IO_TAG(RX_NSS_PIN)), OWNER_SPI, RESOURCE_SPI_CS, rxSPIDevice + 1);
#endif // USE_RX_SOFTSPI

#if defined(STM32F10X)
    RCC_AHBPeriphClockCmd(RX_NSS_GPIO_CLK_PERIPHERAL, ENABLE);
    RCC_AHBPeriphClockCmd(RX_CE_GPIO_CLK_PERIPHERAL, ENABLE);
#endif

#ifdef RX_CE_PIN
    // CE as OUTPUT
    IOInit(IOGetByTag(IO_TAG(RX_CE_PIN)), OWNER_RX_SPI, RESOURCE_RX_CE, rxSPIDevice + 1);
#if defined(STM32F10X)
    IOConfigGPIO(IOGetByTag(IO_TAG(RX_CE_PIN)), SPI_IO_CS_CFG);
#elif defined(STM32F3) || defined(STM32F4)
    IOConfigGPIOAF(IOGetByTag(IO_TAG(RX_CE_PIN)), SPI_IO_CS_CFG, 0);
#endif
    RX_CE_LO();
#endif // RX_CE_PIN
    DISABLE_RX();

#ifdef RX_SPI_INSTANCE
    spiSetDivisor(RX_SPI_INSTANCE, SPI_CLOCK_STANDARD);
#endif
    hardwareInitialised = true;
}

开发者ID:iforce2d，项目名称:cleanflight，代码行数:42，代码来源:rx_spi.c

示例19: IOInit

serialPort_t *usbVcpOpen(void)
{
    vcpPort_t *s;

#ifdef STM32F4
    IOInit(IOGetByTag(IO_TAG(PA11)), OWNER_USB, RESOURCE_INPUT, 0);
    IOInit(IOGetByTag(IO_TAG(PA12)), OWNER_USB, RESOURCE_OUTPUT, 0);
    USBD_Init(&USB_OTG_dev, USB_OTG_FS_CORE_ID, &USR_desc, &USBD_CDC_cb, &USR_cb);
#else
    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init();
#endif

    s = &vcpPort;
    s->port.vTable = usbVTable;

    return (serialPort_t *)s;
}

开发者ID:oleost，项目名称:inav，代码行数:20，代码来源:serial_usb_vcp.c

示例20: resetBeeperConfig

void resetBeeperConfig(beeperConfig_t *beeperConfig)
{
#ifdef BEEPER_INVERTED
    beeperConfig->isOD = false;
    beeperConfig->isInverted = true;
#else
    beeperConfig->isOD = true;
    beeperConfig->isInverted = false;
#endif
    beeperConfig->ioTag = IO_TAG(BEEPER);
}

开发者ID:kc10kevin，项目名称:betaflight，代码行数:11，代码来源:config.c

注：本文中的IO_TAG函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ IO_TO_VIRT函数代码示例发布时间：2022-05-30

C++ IO_STATE函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19220|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9996|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8331|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8700|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8644|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9666|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8630|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8004|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8664|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7539|2022-11-06

客服电话

电子邮件

C++ IO_TAG函数代码示例

示例1: RCC_ClockCmd

示例2: pgResetFn_adcConfig

示例3: resetSonarConfig

示例4: IOInit

示例5: i2cInit

示例6: mma8451ConfigureInterrupt

示例7: updateHardwareRevision

示例8: selectMPUIntExtiConfigByHardwareRevision

示例9: targetConfiguration

示例10: detectSpiDevice

示例11: max7456Init

示例12: m25p16_init

示例13: sdcardInsertionDetectDeinit

示例14: targetConfiguration

示例15: sdcardInsertionDetectInit

示例16: pgResetFn_flashConfig

示例17: usbCableDetectInit

示例18: rxSpiDeviceInit

示例19: IOInit

示例20: resetBeeperConfig

请发表评论

全部评论

上一篇：

下一篇：

krishnaik06/Machine-Learning-in-90-days

谈谈matlab中的uint8和double（转） - Rege

armancodv/building-energy-model-matlab:

美元符号为什么是“$”

FGRibreau/import-tweets-to-mastodon: How

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053