C++ IOMUX_MODE函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中IOMUX_MODE函数的典型用法代码示例。如果您正苦于以下问题：C++ IOMUX_MODE函数的具体用法？C++ IOMUX_MODE怎么用？C++ IOMUX_MODE使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了IOMUX_MODE函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: board_nand_setup

static void board_nand_setup(void)
{
	/* CS3: NAND 8-bit */
	static const struct mxc_weimcs cs3 = {
		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  1, 15, 0,  0,  0),
		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
		CSCR_L(2,  0,   0,   1,  3,  1,  3,  3,  0,  0,   0,   1),
		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
		CSCR_A(0,   0,  0,  2,  0,  0,  2,  0,  0,  0,  0,  0,  0,   0)
	};

	mxc_setup_weimcs(3, &cs3);

	mx31_set_gpr(MUX_SDCTL_CSD1_SEL, 1);

	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_WP, MUX_CTL_IN_GPIO));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_CE, MUX_CTL_IN_GPIO));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_RB, MUX_CTL_IN_GPIO));

	/* Make sure to reset the fpga else you cannot access NAND */
	qong_fpga_reset();

	/* Enable NAND flash */
	gpio_set_value(15, 1);
	gpio_set_value(14, 1);
	gpio_direction_output(15, 0);
	gpio_direction_input(16);
	gpio_direction_input(14);

}

开发者ID:Adrizcorp，项目名称:ARM_SOC_FPGA，代码行数:31，代码来源:qong.c

示例2: qong_init_nand_mtd

static void __init qong_init_nand_mtd(void)
{
	/* init CS */
	__raw_writel(0x00004f00, MX31_IO_ADDRESS(MX31_WEIM_CSCRxU(3)));
	__raw_writel(0x20013b31, MX31_IO_ADDRESS(MX31_WEIM_CSCRxL(3)));
	__raw_writel(0x00020800, MX31_IO_ADDRESS(MX31_WEIM_CSCRxA(3)));

	mxc_iomux_set_gpr(MUX_SDCTL_CSD1_SEL, true);

	/* enable pin */
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFCE_B, IOMUX_CONFIG_GPIO));
	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), "nand_enable"))
		gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_NFCE_B), 0);

	/* ready/busy pin */
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFRB, IOMUX_CONFIG_GPIO));
	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFRB), "nand_rdy"))
		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_NFRB));

	/* write protect pin */
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_NFWP_B, IOMUX_CONFIG_GPIO));
	if (!gpio_request(IOMUX_TO_GPIO(MX31_PIN_NFWP_B), "nand_wp"))
		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_NFWP_B));

	platform_device_register(&qong_nand_device);
}

开发者ID:Jackeagle，项目名称:android_kernel_sony_c2305，代码行数:26，代码来源:mach-qong.c

示例3: mxc_init_i2c

static void __init mxc_init_i2c(void)
{
	i2c_register_board_info(1, mx31ads_i2c1_devices,
				ARRAY_SIZE(mx31ads_i2c1_devices));

	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));

	imx31_add_imx_i2c1(NULL);
}

开发者ID:08opt，项目名称:linux，代码行数:10，代码来源:mach-mx31ads.c

示例4: mxc_init_i2c

static void __init mxc_init_i2c(void)
{
#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
	mx31ads_i2c1_devices[0].irq =
			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
#endif
	i2c_register_board_info(1, mx31ads_i2c1_devices,
				ARRAY_SIZE(mx31ads_i2c1_devices));

	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));

	imx31_add_imx_i2c1(NULL);
}

开发者ID:7L，项目名称:pi_plus，代码行数:14，代码来源:mach-mx31ads.c

示例5: board_late_init

int board_late_init(void)
{
#ifdef CONFIG_S6E63D6
	struct s6e63d6 data = {
		/*
		 * See comment in mxc_spi.c::decode_cs() for .cs field format.
		 * We use GPIO 57 as a chipselect for the S6E63D6 and chipselect
		 * 2 of the SPI controller #1, since it is unused.
		 */
		.cs = 2 | (57 << 8),
		.bus = 0,
		.id = 0,
	};
	int ret;

	/* SPI1 */
	mx31_gpio_mux(MUX_CSPI1_SCLK__CSPI1_CLK);
	mx31_gpio_mux(MUX_CSPI1_SPI_RDY__CSPI1_DATAREADY_B);
	mx31_gpio_mux(MUX_CSPI1_MOSI__CSPI1_MOSI);
	mx31_gpio_mux(MUX_CSPI1_MISO__CSPI1_MISO);
	mx31_gpio_mux(MUX_CSPI1_SS0__CSPI1_SS0_B);
	mx31_gpio_mux(MUX_CSPI1_SS1__CSPI1_SS1_B);
	mx31_gpio_mux(MUX_CSPI1_SS2__CSPI1_SS2_B);

	/* start SPI1 clock */
	__REG(CCM_CGR2) = __REG(CCM_CGR2) | (3 << 2);

	/* GPIO 57 */
	/* sw_mux_ctl_key_col4_key_col5_key_col6_key_col7 */
	mx31_gpio_mux(IOMUX_MODE(0x63, MUX_CTL_GPIO));

	/* SPI1 CS2 is free */
	ret = s6e63d6_init(&data);
	if (ret)
		return ret;

	/*
	 * This is a "magic" sequence to initialise a C0240QGLA / C0283QGLC
	 * OLED display connected to a S6E63D6 SPI display controller in the
	 * 18 bit RGB mode
	 */
	s6e63d6_index(&data, 2);
	s6e63d6_param(&data, 0x0182);
	s6e63d6_index(&data, 3);
	s6e63d6_param(&data, 0x8130);
	s6e63d6_index(&data, 0x10);
	s6e63d6_param(&data, 0x0000);
	s6e63d6_index(&data, 5);
	s6e63d6_param(&data, 0x0001);
	s6e63d6_index(&data, 0x22);
#endif
	return 0;
}
#endif

int checkboard (void)
{
	printf("Board: Phytec phyCore i.MX31\n");
	return 0;
}

开发者ID:OpenInkpot-archive，项目名称:uboot-n516，代码行数:60，代码来源:imx31_phycore.c

示例6: mx31ads_init_expio

static void __init mx31ads_init_expio(void)
{
	int irq_base;
	int i, irq;

	printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");

	/*
	 * Configure INT line as GPIO input
	 */
	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");

	/* disable the interrupt and clear the status */
	__raw_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
	__raw_writew(0xFFFF, PBC_INTSTATUS_REG);

	irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
	WARN_ON(irq_base < 0);

	domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
				       &irq_domain_simple_ops, NULL);
	WARN_ON(!domain);

	for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
		irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
		set_irq_flags(i, IRQF_VALID);
	}
	irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_4));
	irq_set_irq_type(irq, IRQ_TYPE_LEVEL_HIGH);
	irq_set_chained_handler(irq, mx31ads_expio_irq_handler);
}

开发者ID:7L，项目名称:pi_plus，代码行数:31，代码来源:mach-mx31ads.c

示例7: kzm_init_ext_uart

static int __init kzm_init_ext_uart(void)
{
	u8 tmp;

	/*
	 * GPIO 1-1: external UART interrupt line
	 */
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO));
	gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "ext-uart-int");
	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));

	/*
	 * Unmask UART interrupt
	 */
	tmp = __raw_readb(KZM_ARM11_IO_ADDRESS(KZM_ARM11_CTL1));
	tmp |= 0x2;
	__raw_writeb(tmp, KZM_ARM11_IO_ADDRESS(KZM_ARM11_CTL1));

	serial_platform_data[0].irq =
			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
	serial8250_resources[1].start =
			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
	serial8250_resources[1].end =
			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));

	return platform_device_register(&serial_device);
}

开发者ID:linux-next，项目名称:linux-next，代码行数:27，代码来源:mach-kzm_arm11_01.c

示例8: kzm_init_smsc9118

static int __init kzm_init_smsc9118(void)
{
	/*
	 * GPIO 1-2: SMSC9118 interrupt line
	 */
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_2, IOMUX_CONFIG_GPIO));
	gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2), "smsc9118-int");
	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));

	return platform_device_register(&kzm_smsc9118_device);
}

开发者ID:RhythmEngineering，项目名称:linux-arago-omap3，代码行数:11，代码来源:mach-kzm_arm11_01.c

示例9: kzm_init_smsc9118

static int __init kzm_init_smsc9118(void)
{
	/*
	 * GPIO 1-2: SMSC9118 interrupt line
	 */
	mxc_iomux_mode(IOMUX_MODE(MX31_PIN_GPIO1_2, IOMUX_CONFIG_GPIO));
	gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2), "smsc9118-int");
	gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));

	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));

	kzm_smsc9118_resources[1].start =
			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));
	kzm_smsc9118_resources[1].end =
			gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_2));

	return platform_device_register(&kzm_smsc9118_device);
}

开发者ID:linux-next，项目名称:linux-next，代码行数:18，代码来源:mach-kzm_arm11_01.c

示例10: usbotg_init

static int usbotg_init(struct platform_device *pdev)
{
	unsigned int pins[] = {
		MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
		MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
		MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
		MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
		MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
		MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
		MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
		MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
		MX31_PIN_USBOTG_CLK__USBOTG_CLK,
		MX31_PIN_USBOTG_DIR__USBOTG_DIR,
		MX31_PIN_USBOTG_NXT__USBOTG_NXT,
		MX31_PIN_USBOTG_STP__USBOTG_STP,
	};

	mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB OTG");

	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);

	mxc_iomux_set_gpr(MUX_PGP_USB_4WIRE, true);
	mxc_iomux_set_gpr(MUX_PGP_USB_COMMON, true);

	/* chip select */
	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE2, IOMUX_CONFIG_GPIO),
				"USBOTG_CS");
	gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE2), "USBH1 CS");
	gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE2), 0);

	return 0;
}

开发者ID:Medvedroid，项目名称:OT_903D-kernel-2.6.35.7，代码行数:43，代码来源:mach-mx31lilly.c

示例11: mx31ads_init_expio

static void __init mx31ads_init_expio(void)
{
	int i;

	printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");

	/*
	 * Configure INT line as GPIO input
	 */
	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");

	/* disable the interrupt and clear the status */
	__raw_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
	__raw_writew(0xFFFF, PBC_INTSTATUS_REG);
	for (i = MXC_EXP_IO_BASE; i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES);
	     i++) {
		irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
		set_irq_flags(i, IRQF_VALID);
	}
	irq_set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_HIGH);
	irq_set_chained_handler(EXPIO_PARENT_INT, mx31ads_expio_irq_handler);
}

开发者ID:08opt，项目名称:linux，代码行数:22，代码来源:mach-mx31ads.c

示例12: usbh2_init

static int usbh2_init(struct platform_device *pdev)
{
	int pins[] = {
		MX31_PIN_USBH2_DATA0__USBH2_DATA0,
		MX31_PIN_USBH2_DATA1__USBH2_DATA1,
		MX31_PIN_USBH2_CLK__USBH2_CLK,
		MX31_PIN_USBH2_DIR__USBH2_DIR,
		MX31_PIN_USBH2_NXT__USBH2_NXT,
		MX31_PIN_USBH2_STP__USBH2_STP,
	};

	mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2");

	mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
	mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);

	mxc_iomux_set_gpr(MUX_PGP_UH2, true);

	/* chip select */
	mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO),
				"USBH2_CS");
	gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS");
	gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0);

	mdelay(10);

	return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
}

开发者ID:GerardGarcia，项目名称:linux，代码行数:38，代码来源:mach-mx31lilly.c

示例13: IOMUX_MODE

#include <mach/common.h>
#include <mach/board-mx31lite.h>
#include <mach/iomux-mx3.h>
#include <mach/irqs.h>
#include <mach/ulpi.h>

#include "devices-imx31.h"
#include "devices.h"

/*
 * This file contains the module-specific initialization routines.
 */

static unsigned int mx31lite_pins[] = {
	/* LAN9117 IRQ pin */
	IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO),
	/* SPI 1 */
	MX31_PIN_CSPI2_SCLK__SCLK,
	MX31_PIN_CSPI2_MOSI__MOSI,
	MX31_PIN_CSPI2_MISO__MISO,
	MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
	MX31_PIN_CSPI2_SS0__SS0,
	MX31_PIN_CSPI2_SS1__SS1,
	MX31_PIN_CSPI2_SS2__SS2,
};

static const struct mxc_nand_platform_data
mx31lite_nand_board_info __initconst  = {
	.width = 1,
	.hw_ecc = 1,
};

开发者ID:15-712，项目名称:linux-2.6，代码行数:31，代码来源:mach-mx31lite.c

示例14: pcm037_usb_init

static void pcm037_usb_init(void)
{
	u32 tmp;

	/* enable clock */
	tmp = readl(0x53f80000);
	tmp |= (1 << 9);
	writel(tmp, 0x53f80000);

	/* Host 1 */
	tmp = readl(MX31_USB_OTG_BASE_ADDR + 0x600);
	tmp &= ~((3 << 21) | 1);
	tmp |= (1 << 5) | (1 << 16) | (1 << 19) | (1 << 11) | (1 << 20);
	writel(tmp, MX31_USB_OTG_BASE_ADDR + 0x600);

	tmp = readl(MX31_USB_OTG_BASE_ADDR + 0x184);
	tmp &= ~(3 << 30);
	tmp |= 2 << 30;
	writel(tmp, MX31_USB_OTG_BASE_ADDR + 0x184);

	imx_iomux_mode(MX31_PIN_USBOTG_DATA0__USBOTG_DATA0);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA1__USBOTG_DATA1);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA2__USBOTG_DATA2);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA3__USBOTG_DATA3);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA4__USBOTG_DATA4);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA5__USBOTG_DATA5);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA6__USBOTG_DATA6);
	imx_iomux_mode(MX31_PIN_USBOTG_DATA7__USBOTG_DATA7);
	imx_iomux_mode(MX31_PIN_USBOTG_CLK__USBOTG_CLK);
	imx_iomux_mode(MX31_PIN_USBOTG_DIR__USBOTG_DIR);
	imx_iomux_mode(MX31_PIN_USBOTG_NXT__USBOTG_NXT);
	imx_iomux_mode(MX31_PIN_USBOTG_STP__USBOTG_STP);

	mdelay(50);
	ulpi_setup((void *)(MX31_USB_OTG_BASE_ADDR + 0x170), 1);

	/* Host 2 */
	tmp = readl(MX31_IOMUXC_GPR);
	tmp |= 1 << 11;	/* IOMUX GPR: enable USBH2 signals */
	writel(tmp, MX31_IOMUXC_GPR);

	imx_iomux_mode(IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC));
	imx_iomux_mode(IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC));

#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
	imx_iomux_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
	imx_iomux_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
	imx_iomux_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
	imx_iomux_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
	imx_iomux_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
	imx_iomux_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
	imx_iomux_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG);	/* USBH2_DATA2 */
	imx_iomux_set_pad(MX31_PIN_STXD6, H2_PAD_CFG);	/* USBH2_DATA3 */
	imx_iomux_set_pad(MX31_PIN_SFS3, H2_PAD_CFG);	/* USBH2_DATA4 */
	imx_iomux_set_pad(MX31_PIN_SCK3, H2_PAD_CFG);	/* USBH2_DATA5 */
	imx_iomux_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG);	/* USBH2_DATA6 */
	imx_iomux_set_pad(MX31_PIN_STXD3, H2_PAD_CFG);	/* USBH2_DATA7 */

	tmp = readl(MX31_USB_OTG_BASE_ADDR + 0x600);
	tmp &= ~((3 << 21) | 1);
	tmp |= (1 << 5) | (1 << 16) | (1 << 19) | (1 << 20);
	writel(tmp, MX31_USB_OTG_BASE_ADDR + 0x600);

	tmp = readl(MX31_USB_OTG_BASE_ADDR + 0x584);
	tmp &= ~(3 << 30);
	tmp |= 2 << 30;
	writel(tmp, MX31_USB_OTG_BASE_ADDR + 0x584);

	mdelay(50);
	ulpi_setup((void *)(MX31_USB_OTG_BASE_ADDR + 0x570), 1);

	/* Set to Host mode */
	tmp = readl(MX31_USB_OTG_BASE_ADDR + 0x1a8);
	writel(tmp | 0x3, MX31_USB_OTG_BASE_ADDR + 0x1a8);

}

开发者ID:AshishNamdev，项目名称:barebox，代码行数:86，代码来源:pcm037.c

示例15: IOMUX_MODE

	MX31_PIN_TXD1__TXD1,
	MX31_PIN_CTS1__CTS1,
	MX31_PIN_RTS1__RTS1,
	/* I2C */
	MX31_PIN_CSPI2_MOSI__SCL,
	MX31_PIN_CSPI2_MISO__SDA,
	MX31_PIN_CSPI2_SS2__I2C3_SDA,
	MX31_PIN_CSPI2_SCLK__I2C3_SCL,
	/* SDHC1 */
	MX31_PIN_SD1_DATA3__SD1_DATA3,
	MX31_PIN_SD1_DATA2__SD1_DATA2,
	MX31_PIN_SD1_DATA1__SD1_DATA1,
	MX31_PIN_SD1_DATA0__SD1_DATA0,
	MX31_PIN_SD1_CLK__SD1_CLK,
	MX31_PIN_SD1_CMD__SD1_CMD,
	IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO), /* card detect */
	IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), /* write protect */
	/* SPI1 */
	MX31_PIN_CSPI1_MOSI__MOSI,
	MX31_PIN_CSPI1_MISO__MISO,
	MX31_PIN_CSPI1_SCLK__SCLK,
	MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
	MX31_PIN_CSPI1_SS0__SS0,
	MX31_PIN_CSPI1_SS1__SS1,
	MX31_PIN_CSPI1_SS2__SS2,
	/* UART2 */
	MX31_PIN_TXD2__TXD2,
	MX31_PIN_RXD2__RXD2,
	MX31_PIN_CTS2__CTS2,
	MX31_PIN_RTS2__RTS2,
	/* UART3 */

开发者ID:AshishNamdev，项目名称:barebox，代码行数:31，代码来源:pcm037.c

示例16: board_early_init_f

int board_early_init_f(void)
{
#ifdef CONFIG_QONG_FPGA
	/* CS1: FPGA/Network Controller/GPIO, 16-bit, no DTACK */
	static const struct mxc_weimcs cs1 = {
		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  0, 10, 0,  0,  1),
		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
		CSCR_L(2,  0,   0,   4,  0,  0,  5,  0,  0,  0,   0,   1),
		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
		CSCR_A(0,   4,  0,  2,  0,  0,  3,  0,  0,  0,  0,  0,   0,  0)
	};

	mxc_setup_weimcs(1, &cs1);

	/* setup pins for FPGA */
	mx31_gpio_mux(IOMUX_MODE(0x76, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x7e, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x91, MUX_CTL_OUT_FUNC | MUX_CTL_IN_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x92, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x93, MUX_CTL_GPIO));

	/* FPGA reset  Pin */
	/* rstn = 0 */
	gpio_direction_output(QONG_FPGA_RST_PIN, 0);

	/* set interrupt pin as input */
	gpio_direction_input(QONG_FPGA_IRQ_PIN);

	/* FPGA JTAG Interface */
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS6, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK6, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CAPTURE, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_COMPARE, MUX_CTL_GPIO));
	gpio_direction_output(QONG_FPGA_TCK_PIN, 0);
	gpio_direction_output(QONG_FPGA_TMS_PIN, 0);
	gpio_direction_output(QONG_FPGA_TDI_PIN, 0);
	gpio_direction_input(QONG_FPGA_TDO_PIN);
#endif

	/* setup pins for UART1 */
	mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
	mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
	mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
	mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);

	/* setup pins for SPI (pmic) */
	mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B);
	mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI);
	mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO);
	mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
	mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);

	/* Setup pins for USB2 Host */
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_CLK, MUX_CTL_FUNC));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DIR, MUX_CTL_FUNC));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_NXT, MUX_CTL_FUNC));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));

#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)

	mx31_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
	mx31_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
	mx31_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
	mx31_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
	mx31_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
	mx31_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
	mx31_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG);	/* USBH2_DATA2 */
	mx31_set_pad(MX31_PIN_STXD6, H2_PAD_CFG);	/* USBH2_DATA3 */
	mx31_set_pad(MX31_PIN_SFS3, H2_PAD_CFG);	/* USBH2_DATA4 */
	mx31_set_pad(MX31_PIN_SCK3, H2_PAD_CFG);	/* USBH2_DATA5 */
	mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG);	/* USBH2_DATA6 */
	mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG);	/* USBH2_DATA7 */

	mx31_set_gpr(MUX_PGP_UH2, 1);

	return 0;

}

开发者ID:Adrizcorp，项目名称:ARM_SOC_FPGA，代码行数:82，代码来源:qong.c

示例17: IOMUX_MODE

#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>

#include <mach/common.h>
#include <mach/iomux-mx3.h>

#include <asm/mach-types.h>

#include "pcm037.h"
#include "devices-imx31.h"

static unsigned int pcm037_eet_pins[] = {
	/*                                                        */
	IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO),
	/*           */
	IOMUX_MODE(MX31_PIN_GPIO1_0,	IOMUX_CONFIG_GPIO), /*   */
	IOMUX_MODE(MX31_PIN_GPIO1_1,	IOMUX_CONFIG_GPIO), /*   */
	IOMUX_MODE(MX31_PIN_GPIO1_2,	IOMUX_CONFIG_GPIO), /*   */
	IOMUX_MODE(MX31_PIN_GPIO1_3,	IOMUX_CONFIG_GPIO), /*   */
	IOMUX_MODE(MX31_PIN_SVEN0,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_STX0,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_SRX0,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_SIMPD0,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_RTS1,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_CTS1,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_KEY_ROW4,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_KEY_ROW5,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_KEY_ROW6,	IOMUX_CONFIG_GPIO), /*    */
	IOMUX_MODE(MX31_PIN_KEY_ROW7,	IOMUX_CONFIG_GPIO), /*    */

开发者ID:curbthepain，项目名称:android_kernel_us990_rev，代码行数:31，代码来源:mach-pcm037_eet.c

示例18: IOMUX_MODE

#include "devices.h"
#include "crm_regs.h"

static int armadillo5x0_pins[] = {
	/* UART1 */
	MX31_PIN_CTS1__CTS1,
	MX31_PIN_RTS1__RTS1,
	MX31_PIN_TXD1__TXD1,
	MX31_PIN_RXD1__RXD1,
	/* UART2 */
	MX31_PIN_CTS2__CTS2,
	MX31_PIN_RTS2__RTS2,
	MX31_PIN_TXD2__TXD2,
	MX31_PIN_RXD2__RXD2,
	/* LAN9118_IRQ */
	IOMUX_MODE(MX31_PIN_GPIO1_0, IOMUX_CONFIG_GPIO),
	/* SDHC1 */
	MX31_PIN_SD1_DATA3__SD1_DATA3,
	MX31_PIN_SD1_DATA2__SD1_DATA2,
	MX31_PIN_SD1_DATA1__SD1_DATA1,
	MX31_PIN_SD1_DATA0__SD1_DATA0,
	MX31_PIN_SD1_CLK__SD1_CLK,
	MX31_PIN_SD1_CMD__SD1_CMD,
	/* Framebuffer */
	MX31_PIN_LD0__LD0,
	MX31_PIN_LD1__LD1,
	MX31_PIN_LD2__LD2,
	MX31_PIN_LD3__LD3,
	MX31_PIN_LD4__LD4,
	MX31_PIN_LD5__LD5,
	MX31_PIN_LD6__LD6,

开发者ID:1plus4，项目名称:ev3sources，代码行数:31，代码来源:armadillo5x0.c

示例19: IOMUX_TO_IRQ

#include <mach/mx3fb.h>
#include <mach/mx3_camera.h>

#include "devices-imx31.h"
#include "devices.h"

/* CPLD IRQ line for external uart, external ethernet etc */
#define EXPIO_PARENT_INT	IOMUX_TO_IRQ(MX31_PIN_GPIO1_1)

static int mx31_3ds_pins[] = {
	/* UART1 */
	MX31_PIN_CTS1__CTS1,
	MX31_PIN_RTS1__RTS1,
	MX31_PIN_TXD1__TXD1,
	MX31_PIN_RXD1__RXD1,
	IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO),
	/*SPI0*/
	MX31_PIN_CSPI1_SCLK__SCLK,
	MX31_PIN_CSPI1_MOSI__MOSI,
	MX31_PIN_CSPI1_MISO__MISO,
	MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
	MX31_PIN_CSPI1_SS2__SS2, /* CS for LCD */
	/* SPI 1 */
	MX31_PIN_CSPI2_SCLK__SCLK,
	MX31_PIN_CSPI2_MOSI__MOSI,
	MX31_PIN_CSPI2_MISO__MISO,
	MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
	MX31_PIN_CSPI2_SS0__SS0,
	MX31_PIN_CSPI2_SS2__SS2, /*CS for MC13783 */
	/* MC13783 IRQ */
	IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO),

开发者ID:mesosexy，项目名称:linux-2.6，代码行数:31，代码来源:mach-mx31_3ds.c

示例20: board_init

int board_init (void)
{
	/* Chip selects */
	/* CS0: Nor Flash #0 - it must be init'ed when executing from DDR */
	/* Assumptions: HCLK = 133 MHz, tACC = 130ns */
	__REG(CSCR_U(0)) = ((0 << 31)	| /* SP */
						(0 << 30)	| /* WP */
						(0 << 28)	| /* BCD */
						(0 << 24)	| /* BCS */
						(0 << 22)	| /* PSZ */
						(0 << 21)	| /* PME */
						(0 << 20)	| /* SYNC */
						(0 << 16)	| /* DOL */
						(3 << 14)	| /* CNC */
						(21 << 8)	| /* WSC */
						(0 << 7)	| /* EW */
						(0 << 4)	| /* WWS */
						(6 << 0)	  /* EDC */
					   );

	__REG(CSCR_L(0)) = ((2 << 28)	| /* OEA */
						(1 << 24)	| /* OEN */
						(3 << 20)	| /* EBWA */
						(3 << 16)	| /* EBWN */
						(1 << 12)	| /* CSA */
						(1 << 11)	| /* EBC */
						(5 << 8)	| /* DSZ */
						(1 << 4)	| /* CSN */
						(0 << 3)	| /* PSR */
						(0 << 2)	| /* CRE */
						(0 << 1)	| /* WRAP */
						(1 << 0)	  /* CSEN */
					   );

	__REG(CSCR_A(0)) = ((2 << 28)	| /* EBRA */
						(1 << 24)	| /* EBRN */
						(2 << 20)	| /* RWA */
						(2 << 16)	| /* RWN */
						(0 << 15)	| /* MUM */
						(0 << 13)	| /* LAH */
						(2 << 10)	| /* LBN */
						(0 << 8)	| /* LBA */
						(0 << 6)	| /* DWW */
						(0 << 4)	| /* DCT */
						(0 << 3)	| /* WWU */
						(0 << 2)	| /* AGE */
						(0 << 1)	| /* CNC2 */
						(0 << 0)	  /* FCE */
					   );

#ifdef CONFIG_QONG_FPGA
	/* CS1: FPGA/Network Controller/GPIO */
	/* 16-bit, no DTACK */
	__REG(CSCR_U(1)) = 0x00000A01;
	__REG(CSCR_L(1)) = 0x20040501;
	__REG(CSCR_A(1)) = 0x04020C00;

	/* setup pins for FPGA */
	mx31_gpio_mux(IOMUX_MODE(0x76, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x7e, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x91, MUX_CTL_OUT_FUNC | MUX_CTL_IN_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x92, MUX_CTL_GPIO));
	mx31_gpio_mux(IOMUX_MODE(0x93, MUX_CTL_GPIO));
#endif

	/* setup pins for UART1 */
	mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
	mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
	mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
	mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);

	/* board id for linux */
	gd->bd->bi_arch_number = MACH_TYPE_QONG;
	gd->bd->bi_boot_params = (0x80000100);	/* adress of boot parameters */

	return 0;
}

开发者ID:12thmantec，项目名称:u-boot-novena-spl，代码行数:77，代码来源:qong.c

注：本文中的IOMUX_MODE函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ IOMUX_TO_GPIO函数代码示例发布时间：2022-05-30

C++ IOMEM函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19219|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9996|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8331|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8700|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8644|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9666|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8630|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8004|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8664|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7539|2022-11-06

客服电话

电子邮件

C++ IOMUX_MODE函数代码示例

示例1: board_nand_setup

示例2: qong_init_nand_mtd

示例3: mxc_init_i2c

示例4: mxc_init_i2c

示例5: board_late_init

示例6: mx31ads_init_expio

示例7: kzm_init_ext_uart

示例8: kzm_init_smsc9118

示例9: kzm_init_smsc9118

示例10: usbotg_init

示例11: mx31ads_init_expio

示例12: usbh2_init

示例13: IOMUX_MODE

示例14: pcm037_usb_init

示例15: IOMUX_MODE

示例16: board_early_init_f

示例17: IOMUX_MODE

示例18: IOMUX_MODE

示例19: IOMUX_TO_IRQ

示例20: board_init

请发表评论

全部评论

上一篇：

下一篇：

krishnaik06/Machine-Learning-in-90-days

elm/core: Elm&#39;s core libraries

armancodv/building-energy-model-matlab:

美元符号为什么是“$”

FGRibreau/import-tweets-to-mastodon: How

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053

elm/core: Elm's core libraries