• 设为首页
  • 点击收藏
  • 手机版
    手机扫一扫访问
    迪恩网络手机版
  • 关注官方公众号
    微信扫一扫关注
    公众号

C++ I2CMasterBaseValid函数代码示例

原作者: [db:作者] 来自: [db:来源] 收藏 邀请

本文整理汇总了C++中I2CMasterBaseValid函数的典型用法代码示例。如果您正苦于以下问题:C++ I2CMasterBaseValid函数的具体用法?C++ I2CMasterBaseValid怎么用?C++ I2CMasterBaseValid使用的例子?那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。



在下文中一共展示了I2CMasterBaseValid函数的20个代码示例,这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞,您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: I2CMasterControl

//*****************************************************************************
//
//! Controls the state of the I2C Master module.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ulCmd command to be issued to the I2C Master module.
//!
//! This function is used to control the state of the Master module send and
//! receive operations.  The \e ucCmd parameter can be one of the following
//! values:
//!
//! - \b I2C_MASTER_CMD_SINGLE_SEND
//! - \b I2C_MASTER_CMD_SINGLE_RECEIVE
//! - \b I2C_MASTER_CMD_BURST_SEND_START
//! - \b I2C_MASTER_CMD_BURST_SEND_CONT
//! - \b I2C_MASTER_CMD_BURST_SEND_FINISH
//! - \b I2C_MASTER_CMD_BURST_SEND_ERROR_STOP
//! - \b I2C_MASTER_CMD_BURST_RECEIVE_START
//! - \b I2C_MASTER_CMD_BURST_RECEIVE_CONT
//! - \b I2C_MASTER_CMD_BURST_RECEIVE_FINISH
//! - \b I2C_MASTER_CMD_BURST_RECEIVE_ERROR_STOP
//! - \b I2C_MASTER_CMD_QUICK_COMMAND
//! - \b I2C_MASTER_CMD_HS_MASTER_CODE_SEND
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterControl(unsigned long ulBase, unsigned long ulCmd)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));
    ASSERT((ulCmd == I2C_MASTER_CMD_SINGLE_SEND) ||
           (ulCmd == I2C_MASTER_CMD_SINGLE_RECEIVE) ||
           (ulCmd == I2C_MASTER_CMD_BURST_SEND_START) ||
           (ulCmd == I2C_MASTER_CMD_BURST_SEND_CONT) ||
           (ulCmd == I2C_MASTER_CMD_BURST_SEND_FINISH) ||
           (ulCmd == I2C_MASTER_CMD_BURST_SEND_ERROR_STOP) ||
           (ulCmd == I2C_MASTER_CMD_BURST_RECEIVE_START) ||
           (ulCmd == I2C_MASTER_CMD_BURST_RECEIVE_CONT) ||
           (ulCmd == I2C_MASTER_CMD_BURST_RECEIVE_FINISH) ||
           (ulCmd == I2C_MASTER_CMD_BURST_RECEIVE_ERROR_STOP) ||
           (ulCmd == I2C_MASTER_CMD_QUICK_COMMAND) ||
           (ulCmd == I2C_MASTER_CMD_HS_MASTER_CODE_SEND));

    //
    // Send the command.
    //
    HWREG(ulBase + I2C_O_MCS) = ulCmd;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:52,代码来源:i2c.c


示例2: I2CIntRegister

//*****************************************************************************
//
//! Registers an interrupt handler for the I2C module.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param pfnHandler is a pointer to the function to be called when the
//! I2C interrupt occurs.
//!
//! This function sets the handler to be called when an I2C interrupt occurs.
//! This function enables the global interrupt in the interrupt controller;
//! specific I2C interrupts must be enabled via I2CMasterIntEnable() and
//! I2CSlaveIntEnable().  If necessary, it is the interrupt handler's
//! responsibility to clear the interrupt source via I2CMasterIntClear() and
//! I2CSlaveIntClear().
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
I2CIntRegister(unsigned long ulBase, void (*pfnHandler)(void))
{
    unsigned long ulInt;

    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Determine the interrupt number based on the I2C port.
    //
    ulInt = I2CIntNumberGet(ulBase);

    //
    // Register the interrupt handler, returning an error if an error occurs.
    //
    IntRegister(ulInt, pfnHandler);

    //
    // Enable the I2C interrupt.
    //
    IntEnable(ulInt);
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:46,代码来源:i2c.c


示例3: I2CIntUnregister

//*****************************************************************************
//
//! Unregisters an interrupt handler for the I2C module.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function clears the handler to be called when an I2C interrupt
//! occurs.  This function also masks off the interrupt in the interrupt r
//! controlle so that the interrupt handler no longer is called.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
I2CIntUnregister(unsigned long ulBase)
{
    unsigned long ulInt;

    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Determine the interrupt number based on the I2C port.
    //
    ulInt = I2CIntNumberGet(ulBase);

    //
    // Disable the interrupt.
    //
    IntDisable(ulInt);

    //
    // Unregister the interrupt handler.
    //
    IntUnregister(ulInt);
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:41,代码来源:i2c.c


示例4: I2CMasterTimeoutSet

//*****************************************************************************
//
//! Sets the Master clock timeout value.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ulValue is the number of I2C clocks before the timeout is asserted.
//!
//! This function enables and configures the clock low timeout feature in the
//! I2C peripheral.  This feature is implemented as a 12-bit counter, with the
//! upper 8-bits being programmable.  For example, to program a timeout of 20ms
//! with a 100kHz SCL frequency, \e ulValue would be 0x7d.
//!
//! \note Not all Stellaris devices support this function.  Please consult the
//! device data sheet to determine if this feature is supported.
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterTimeoutSet(unsigned long ulBase, unsigned long ulValue)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Write the timeout value.
    //
    HWREG(ulBase + I2C_O_MCLKOCNT) = ulValue;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:31,代码来源:i2c.c


示例5: I2CMasterDataGet

//*****************************************************************************
//
//! Receives a byte that has been sent to the I2C Master.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function reads a byte of data from the I2C Master Data Register.
//!
//! \return Returns the byte received from by the I2C Master, cast as an
//! unsigned long.
//
//*****************************************************************************
unsigned long
I2CMasterDataGet(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Read a byte.
    //
    return(HWREG(ulBase + I2C_O_MDR));
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:25,代码来源:i2c.c


示例6: I2CMasterDisable

//*****************************************************************************
//
//! Disables the I2C master block.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function disables operation of the I2C master block.
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterDisable(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Disable the master block.
    //
    HWREG(ulBase + I2C_O_MCR) &= ~(I2C_MCR_MFE);
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:24,代码来源:i2c.c


示例7: I2CMasterLineStateGet

//*****************************************************************************
//
//! Reads the state of the SDA and SCL pins.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function returns the state of the I2C bus by providing the real time
//! values of the SDA and SCL pins.
//!
//! \note Not all Stellaris devices support this function.  Please consult the
//! device data sheet to determine if this feature is supported.
//!
//! \return Returns the state of the bus with SDA in bit position 1 and SCL in
//! bit position 0.
//
//*****************************************************************************
unsigned long
I2CMasterLineStateGet(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Return the line state.
    //
    return(HWREG(ulBase + I2C_O_MBMON));
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:29,代码来源:i2c.c


示例8: I2CMasterIntClearEx

//*****************************************************************************
//
//! Clears I2C Master interrupt sources.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ulIntFlags is a bit mask of the interrupt sources to be cleared.
//!
//! The specified I2C Master interrupt sources are cleared, so that they no
//! longer assert.  This function must be called in the interrupt handler to
//! keep the interrupt from being triggered again immediately upon exit.
//!
//! The \e ulIntFlags parameter has the same definition as the \e ulIntFlags
//! parameter to I2CMasterIntEnableEx().
//!
//! \note Because there is a write buffer in the Cortex-M processor, it may
//! take several clock cycles before the interrupt source is actually cleared.
//! Therefore, it is recommended that the interrupt source be cleared early in
//! the interrupt handler (as opposed to the very last action) to avoid
//! returning from the interrupt handler before the interrupt source is
//! actually cleared.  Failure to do so may result in the interrupt handler
//! being immediately reentered (because the interrupt controller still sees
//! the interrupt source asserted).
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterIntClearEx(unsigned long ulBase, unsigned long ulIntFlags)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Clear the I2C master interrupt source.
    //
    HWREG(ulBase + I2C_O_MICR) = ulIntFlags;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:39,代码来源:i2c.c


示例9: I2CMasterIntEnable

//*****************************************************************************
//
//! Enables the I2C Master interrupt.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function enables the I2C Master interrupt source.
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterIntEnable(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Enable the master interrupt.
    //
    HWREG(ulBase + I2C_O_MIMR) = 1;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:24,代码来源:i2c.c


示例10: I2CMasterIntDisableEx

//*****************************************************************************
//
//! Disables individual I2C Master interrupt sources.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ulIntFlags is the bit mask of the interrupt sources to be disabled.
//!
//! This function disables the indicated I2C Master interrupt sources.  Only
//! the sources that are enabled can be reflected to the processor interrupt;
//! disabled sources have no effect on the processor.
//!
//! The \e ulIntFlags parameter has the same definition as the \e ulIntFlags
//! parameter to I2CMasterIntEnableEx().
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterIntDisableEx(unsigned long ulBase, unsigned long ulIntFlags)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Disable the master interrupt.
    //
    HWREG(ulBase + I2C_O_MIMR) &= ~ulIntFlags;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:30,代码来源:i2c.c


示例11: I2CMasterDataPut

//*****************************************************************************
//
//! Transmits a byte from the I2C Master.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ucData data to be transmitted from the I2C Master.
//!
//! This function places the supplied data into I2C Master Data Register.
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterDataPut(unsigned long ulBase, unsigned char ucData)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Write the byte.
    //
    HWREG(ulBase + I2C_O_MDR) = ucData;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:25,代码来源:i2c.c


示例12: I2CMasterInitExpClk

//*****************************************************************************
//
//! Initializes the I2C Master block.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ulI2CClk is the rate of the clock supplied to the I2C module.
//! \param bFast set up for fast data transfers.
//!
//! This function initializes operation of the I2C Master block by configuring
//! the bus speed for the master and enabling the I2C Master block.
//!
//! If the parameter \e bFast is \b true, then the master block is set up to
//! transfer data at 400 Kbps; otherwise, it is set up to transfer data at
//! 100 Kbps.  If Fast Mode Plus (1 Mbps) is desired, software should manually
//! write the I2CMTPR after calling this function.  For High Speed (3.4 Mbps)
//! mode, a specific command is used to switch to the faster clocks after the
//! initial communication with the slave is done at either 100 Kbps or
//! 400 Kbps.
//!
//! The peripheral clock is the same as the processor clock.  This value is
//! returned by SysCtlClockGet(), or it can be explicitly hard coded if it is
//! constant and known (to save the code/execution overhead of a call to
//! SysCtlClockGet()).
//!
//! This function replaces the original I2CMasterInit() API and performs the
//! same actions.  A macro is provided in <tt>i2c.h</tt> to map the original
//! API to this API.
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterInitExpClk(unsigned long ulBase, unsigned long ulI2CClk,
                    tBoolean bFast)
{
    unsigned long ulSCLFreq;
    unsigned long ulTPR;

    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Must enable the device before doing anything else.
    //
    I2CMasterEnable(ulBase);

    //
    // Get the desired SCL speed.
    //
    if(bFast == true)
    {
        ulSCLFreq = 400000;
    }
    else
    {
        ulSCLFreq = 100000;
    }

    //
    // Compute the clock divider that achieves the fastest speed less than or
    // equal to the desired speed.  The numerator is biased to favor a larger
    // clock divider so that the resulting clock is always less than or equal
    // to the desired clock, never greater.
    //
    ulTPR = ((ulI2CClk + (2 * 10 * ulSCLFreq) - 1) / (2 * 10 * ulSCLFreq)) - 1;
    HWREG(ulBase + I2C_O_MTPR) = ulTPR;

    //
    // Check to see if this I2C peripheral is High-Speed enabled.  If yes, also
    // choose the fastest speed that is less than or equal to 3.4 Mbps.
    //
    if(HWREG(ulBase + I2C_O_PP) & I2C_PP_HS)
    {
        ulTPR = ((ulI2CClk + (2 * 3 * 3400000) - 1) /
                (2 * 3 * 3400000)) - 1;
        HWREG(ulBase + I2C_O_MTPR) = I2C_MTPR_HS | ulTPR;
    }
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:80,代码来源:i2c.c


示例13: I2CMasterSlaveAddrSet

//*****************************************************************************
//
//! Sets the address that the I2C Master places on the bus.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param ucSlaveAddr 7-bit slave address
//! \param bReceive flag indicating the type of communication with the slave
//!
//! This function configures the address that the I2C Master places on the
//! bus when initiating a transaction.  When the \e bReceive parameter is set
//! to \b true, the address indicates that the I2C Master is initiating a
//! read from the slave; otherwise the address indicates that the I2C
//! Master is initiating a write to the slave.
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterSlaveAddrSet(unsigned long ulBase, unsigned char ucSlaveAddr,
                      tBoolean bReceive)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));
    ASSERT(!(ucSlaveAddr & 0x80));

    //
    // Set the address of the slave with which the master will communicate.
    //
    HWREG(ulBase + I2C_O_MSA) = (ucSlaveAddr << 1) | bReceive;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:32,代码来源:i2c.c


示例14: I2CMasterBusBusy

//*****************************************************************************
//
//! Indicates whether or not the I2C bus is busy.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function returns an indication of whether or not the I2C bus is busy.
//! This function can be used in a multi-master environment to determine if
//! another master is currently using the bus.
//!
//! \return Returns \b true if the I2C bus is busy; otherwise, returns
//! \b false.
//
//*****************************************************************************
tBoolean
I2CMasterBusBusy(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Return the bus busy status.
    //
    if(HWREG(ulBase + I2C_O_MCS) & I2C_MCS_BUSBSY)
    {
        return(true);
    }
    else
    {
        return(false);
    }
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:34,代码来源:i2c.c


示例15: I2CMasterIntClear

//*****************************************************************************
//
//! Clears I2C Master interrupt sources.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! The I2C Master interrupt source is cleared, so that it no longer asserts.
//! This function must be called in the interrupt handler to keep the interrupt
//! from being triggered again immediately upon exit.
//!
//! \note Because there is a write buffer in the Cortex-M processor, it may
//! take several clock cycles before the interrupt source is actually cleared.
//! Therefore, it is recommended that the interrupt source be cleared early in
//! the interrupt handler (as opposed to the very last action) to avoid
//! returning from the interrupt handler before the interrupt source is
//! actually cleared.  Failure to do so may result in the interrupt handler
//! being immediately reentered (because the interrupt controller still sees
//! the interrupt source asserted).
//!
//! \return None.
//
//*****************************************************************************
void
I2CMasterIntClear(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Clear the I2C master interrupt source.
    //
    HWREG(ulBase + I2C_O_MICR) = I2C_MICR_IC;

    //
    // Workaround for I2C master interrupt clear errata for rev B Stellaris
    // devices.  For later devices, this write is ignored and therefore
    // harmless (other than the slight performance hit).
    //
    HWREG(ulBase + I2C_O_MMIS) = I2C_MICR_IC;
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:42,代码来源:i2c.c


示例16: I2CMasterIntStatusEx

//*****************************************************************************
//
//! Gets the current I2C Master interrupt status.
//!
//! \param ulBase is the base address of the I2C Master module.
//! \param bMasked is false if the raw interrupt status is requested and
//! true if the masked interrupt status is requested.
//!
//! This function returns the interrupt status for the I2C Master module.
//! Either the raw interrupt status or the status of interrupts that are
//! allowed to reflect to the processor can be returned.
//!
//! \return Returns the current interrupt status, enumerated as a bit field of
//! values described in I2CMasterIntEnableEx().
//
//*****************************************************************************
unsigned long
I2CMasterIntStatusEx(unsigned long ulBase, tBoolean bMasked)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Return either the interrupt status or the raw interrupt status as
    // requested.
    //
    if(bMasked)
    {
        return(HWREG(ulBase + I2C_O_MMIS));
    }
    else
    {
        return(HWREG(ulBase + I2C_O_MRIS));
    }
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:37,代码来源:i2c.c


示例17: I2CMasterErr

//*****************************************************************************
//
//! Gets the error status of the I2C Master module.
//!
//! \param ulBase is the base address of the I2C Master module.
//!
//! This function is used to obtain the error status of the Master module send
//! and receive operations.
//!
//! \return Returns the error status, as one of \b I2C_MASTER_ERR_NONE,
//! \b I2C_MASTER_ERR_ADDR_ACK, \b I2C_MASTER_ERR_DATA_ACK, or
//! \b I2C_MASTER_ERR_ARB_LOST.
//
//*****************************************************************************
unsigned long
I2CMasterErr(unsigned long ulBase)
{
    unsigned long ulErr;

    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulBase));

    //
    // Get the raw error state
    //
    ulErr = HWREG(ulBase + I2C_O_MCS);

    //
    // If the I2C master is busy, then all the other bit are invalid, and
    // don't have an error to report.
    //
    if(ulErr & I2C_MCS_BUSY)
    {
        return(I2C_MASTER_ERR_NONE);
    }

    //
    // Check for errors.
    //
    if(ulErr & (I2C_MCS_ERROR | I2C_MCS_ARBLST))
    {
        return(ulErr & (I2C_MCS_ARBLST | I2C_MCS_DATACK | I2C_MCS_ADRACK));
    }
    else
    {
        return(I2C_MASTER_ERR_NONE);
    }
}
开发者ID:tbraunP,项目名称:StellarisDriverLib,代码行数:50,代码来源:i2c.c


示例18: I2CRegRead

//*****************************************************************************
//
//! Reads the I2C slave register.
//!
//! \param ulI2CBase is the base for the I2C module.
//! \param ucSlaveAdress is the 7-bit address of the slave to be addressed.
//! \param ucReg is the register to read from.
//!
//! This function initiates a read from the slave device.
//! The ulI2CBase parameter is the I2C modules master base address.
//! \e ulI2CBase parameter can be one of the following values:
//!
//! - \b I2C0_MASTER_BASE
//! - \b I2C1_MASTER_BASE
//! - \b I2C2_MASTER_BASE
//! - \b I2C3_MASTER_BASE
//!
//! \return Register value in an unsigned long format.  Note that 0 will be
//! returned if there is ever an error, 1 if there was not.
//
//*****************************************************************************
unsigned long
I2CRegRead(unsigned long ulI2CBase, unsigned char ucSlaveAdress, unsigned char ucReg)
{
unsigned long ulRegValue = 0;

	//
	// Check the arguments.
	//
	ASSERT(I2CMasterBaseValid(ulI2CBase));

	//
	// Wait until master module is done transferring.
	//
	while(I2CMasterBusy(ulI2CBase))
	{
	};

    //
    // Tell the master module what address it will place on the bus when
    // writing to the slave.
    //
    I2CMasterSlaveAddrSet(ulI2CBase, ucSlaveAdress, 0);

    //
    // Place the command to be sent in the data register.
    //
    I2CMasterDataPut(ulI2CBase, ucReg);

    //
    // Initiate send of data from the master.
    //
    I2CMasterControl(ulI2CBase, I2C_MASTER_CMD_SINGLE_SEND);

    //
    // Wait until master module is done transferring.
    //
    while(I2CMasterBusy(ulI2CBase))
    {
    };

    //
    // Check for errors.
    //
    if(I2CMasterErr(ulI2CBase) != I2C_MASTER_ERR_NONE)
    {
        return 0;
    }

    //
    // Tell the master module what address it will place on the bus when
    // reading from the slave.
    //
    I2CMasterSlaveAddrSet(ulI2CBase, ucSlaveAdress, 1);

    //
    // Tell the master to read data.
    //
    I2CMasterControl(ulI2CBase, I2C_MASTER_CMD_SINGLE_RECEIVE);

    //
    // Wait until master module is done receiving.
    //
    while(I2CMasterBusy(ulI2CBase))
    {
    };

    //
    // Check for errors.
    //
    if(I2CMasterErr(ulI2CBase) != I2C_MASTER_ERR_NONE)
    {
        return 0;
    }

    //
    // Read the data from the master.
    //
    ulRegValue = I2CMasterDataGet(ulI2CBase);

//.........这里部分代码省略.........
开发者ID:cwardcode,项目名称:HydroH20,代码行数:101,代码来源:I2C_Stellaris_API.c


示例19: I2CBusScan

//*****************************************************************************
//
//! Probes the selected I2C bus for available slave devices
//!
//! \param ulI2CBase is the base for the I2C module.
//!
//! This function scans the selected I2C bus for available I2C slave device.
//! The ulI2CBase parameter is the I2C modules master base address.
//! \e ulI2CBase parameter can be one of the following values:
//!
//! - \b I2C0_MASTER_BASE
//! - \b I2C1_MASTER_BASE
//! - \b I2C2_MASTER_BASE
//! - \b I2C3_MASTER_BASE
//!
//! \return 0 if there was an error or 1 if there was not.
//
//*****************************************************************************
unsigned long
I2CBusScan(unsigned long ulI2CBase)
{
	unsigned char ucProbeAdress;
	unsigned long ucerrorstate;

	//
	// Check the arguments.
	//
	ASSERT(I2CMasterBaseValid(ulI2CBase));

	//
	// Wait until master module is done transferring.
	//
	while(I2CMasterBusy(ulI2CBase))
	{
	};

	//
	// I2C Addresses are 7-bit values
	// probe the address range of 0 to 127 to find I2C slave devices on the bus
	//
	for (ucProbeAdress = 0; ucProbeAdress < 127; ucProbeAdress++)
	{
	    //
	    // Tell the master module what address it will place on the bus when
	    // writing to the slave.
	    //
		I2CMasterSlaveAddrSet(ulI2CBase, ucProbeAdress, false);
	    SysCtlDelay(50000);

	    //
	    // Place the command to be sent in the data register.
	    //
	    I2CMasterDataPut(ulI2CBase, 0x00);

	    //
	    // Initiate send of data from the master.
	    //
	    I2CMasterControl(ulI2CBase, I2C_MASTER_CMD_BURST_SEND_START);

	    //
	    // Make some delay
	    //
	    SysCtlDelay(500000);

	    //
	    // Read the I2C Master Control/Status (I2CMCS) Register to a local
	    // variable
	    //
	    ucerrorstate = I2CMasterErr(ulI2CBase);

	    //
	    // Examining the content I2C Master Control/Status (I2CMCS) Register
	    // to see if the ADRACK-Bit (Acknowledge Address) is TRUE (1)
	    // ( 1: The transmitted address was not acknowledged by the slave)
	    //
	    if(ucerrorstate & I2C_MASTER_ERR_ADDR_ACK)
	    {
	    	//
	    	// device at selected address did not acknowledge --> there's no device
	    	// with this address present on the I2C bus
	    	//
	        //
	        // Print a message to Stdio
	        //
	    	//UARTprintf("Address not found: 0x%2x - %3d\n",ucProbeAdress,ucProbeAdress);
		    //
		    // Make some delay
		    //
	    	//ROM_SysCtlDelay(1500000);
	    }

	    //
	    // ( 0: The transmitted address was acknowledged by the slave)
	    //
	    else
	    {
	    	//
	    	// device at selected address acknowledged --> there is a device
	    	// with this address present on the I2C bus
	    	//
//.........这里部分代码省略.........
开发者ID:cwardcode,项目名称:HydroH20,代码行数:101,代码来源:I2C_Stellaris_API.c


示例20: I2CRegWrite

unsigned long
I2CRegWrite(unsigned long ulI2CBase, unsigned char ucSlaveAdress,
         unsigned char ucReg, unsigned char ucValue)
{
    //
    // Check the arguments.
    //
    ASSERT(I2CMasterBaseValid(ulI2CBase));

    //
    // Wait until master module is done transferring.
    //
    while(ROM_I2CMasterBusy(ulI2CBase))
    {
    };

    //
    // Tell the master module what address it will place on the bus when
    // writing to the slave.
    //
    ROM_I2CMasterSlaveAddrSet(ulI2CBase, ucSlaveAdress, 0);

    //
    // Place the command to be sent in the data register.
    //
    ROM_I2CMasterDataPut(ulI2CBase, ucReg);

    //
    // Initiate send of data from the master.
    //
    ROM_I2CMasterControl(ulI2CBase, I2C_MASTER_CMD_BURST_SEND_START);

    //
    // Wait until master module is done transferring.
    //
    while(ROM_I2CMasterBusy(ulI2CBase))
    {
    };

    //
    // Check for errors.
    //
    if(ROM_I2CMasterErr(ulI2CBase) != I2C_MASTER_ERR_NONE)
    {
        return 0;
    }

    //
    // Place the value to be sent in the data register.
    //
    ROM_I2CMasterDataPut(ulI2CBase, ucValue);

    //
    // Initiate send of data from the master.
    //
    ROM_I2CMasterControl(ulI2CBase, I2C_MASTER_CMD_BURST_SEND_CONT);

    //
    // Wait until master module is done transferring.
    //
    while(ROM_I2CMasterBusy(ulI2CBase))
    {
    };

    //
    // Check for errors.
    //
    if(ROM_I2CMasterErr(ulI2CBase) != I2C_MASTER_ERR_NONE)
    {
        return 0;
    }

    //
    // Initiate send of data from the master.
    //
    ROM_I2CMasterControl(ulI2CBase, I2C_MASTER_CMD_BURST_SEND_FINISH);

    //
    // Wait until master module is done transferring.
    //
    while(ROM_I2CMasterBusy(ulI2CBase))
    {
    };

    //
    // Check for errors.
    //
    if(ROM_I2CMasterErr(ulI2CBase) != I2C_MASTER_ERR_NONE)
    {
        return 0;
    }

    //
    // Return 1 if there is no error.
    //
    return 1;
}
开发者ID:aatanvardoo,项目名称:StacjaPogodowaDSP,代码行数:97,代码来源:myI2C.c



注:本文中的I2CMasterBaseValid函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台,相关代码片段筛选自各路编程大神贡献的开源项目,源码版权归原作者所有,传播和使用请参考对应项目的License;未经允许,请勿转载。


鲜花

握手

雷人

路过

鸡蛋
该文章已有0人参与评论

请发表评论

全部评论

专题导读
上一篇:
C++ I2CMasterControl函数代码示例发布时间:2022-05-30
下一篇:
C++ I2A函数代码示例发布时间:2022-05-30
热门推荐
阅读排行榜

扫描微信二维码

查看手机版网站

随时了解更新最新资讯

139-2527-9053

在线客服(服务时间 9:00~18:00)

在线QQ客服
地址:深圳市南山区西丽大学城创智工业园
电邮:jeky_zhao#qq.com
移动电话:139-2527-9053

Powered by 互联科技 X3.4© 2001-2213 极客世界.|Sitemap