• 设为首页
  • 点击收藏
  • 手机版
    手机扫一扫访问
    迪恩网络手机版
  • 关注官方公众号
    微信扫一扫关注
    公众号

C++ HAL_GetTick函数代码示例

原作者: [db:作者] 来自: [db:来源] 收藏 邀请

本文整理汇总了C++中HAL_GetTick函数的典型用法代码示例。如果您正苦于以下问题:C++ HAL_GetTick函数的具体用法?C++ HAL_GetTick怎么用?C++ HAL_GetTick使用的例子?那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。



在下文中一共展示了HAL_GetTick函数的20个代码示例,这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞,您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: HAL_DMA_PollForTransfer

/**
  * @brief  Polling for transfer complete.
  * @param  hdma:          pointer to a DMA_HandleTypeDef structure that contains
  *                        the configuration information for the specified DMA Stream.
  * @param  CompleteLevel: Specifies the DMA level complete.  
  * @param  Timeout:       Timeout duration.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout)
{
  uint32_t temp, tmp, tmp1, tmp2;
  uint32_t tickstart = 0; 

  /* Get the level transfer complete flag */
  if(CompleteLevel == HAL_DMA_FULL_TRANSFER)
  {
    /* Transfer Complete flag */
    temp = __HAL_DMA_GET_TC_FLAG_INDEX(hdma);
  }
  else
  {
    /* Half Transfer Complete flag */
    temp = __HAL_DMA_GET_HT_FLAG_INDEX(hdma);
  }

  /* Get tick */
  tickstart = HAL_GetTick();

  while(__HAL_DMA_GET_FLAG(hdma, temp) == RESET)
  {
    tmp  = __HAL_DMA_GET_FLAG(hdma, __HAL_DMA_GET_TE_FLAG_INDEX(hdma));
    tmp1 = __HAL_DMA_GET_FLAG(hdma, __HAL_DMA_GET_FE_FLAG_INDEX(hdma));
    tmp2 = __HAL_DMA_GET_FLAG(hdma, __HAL_DMA_GET_DME_FLAG_INDEX(hdma));
    if((tmp != RESET) || (tmp1 != RESET) || (tmp2 != RESET))
    {
      if(tmp != RESET)
      {
        /* Update error code */
        hdma->ErrorCode |= HAL_DMA_ERROR_TE;

        /* Clear the transfer error flag */
        __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_TE_FLAG_INDEX(hdma));
      }
      if(tmp1 != RESET)
      {
        /* Update error code */
        hdma->ErrorCode |= HAL_DMA_ERROR_FE;
 
        /* Clear the FIFO error flag */
        __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_FE_FLAG_INDEX(hdma));
      }
      if(tmp2 != RESET)
      {
        /* Update error code */
        hdma->ErrorCode |= HAL_DMA_ERROR_DME;

        /* Clear the Direct Mode error flag */
        __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_DME_FLAG_INDEX(hdma));
      }
      /* Change the DMA state */
      hdma->State= HAL_DMA_STATE_ERROR;
      
      /* Process Unlocked */
      __HAL_UNLOCK(hdma);

      return HAL_ERROR;
    }  
    /* Check for the Timeout */
    if(Timeout != HAL_MAX_DELAY)
    {
      if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
      {
        /* Update error code */
        hdma->ErrorCode |= HAL_DMA_ERROR_TIMEOUT;

        /* Change the DMA state */
        hdma->State = HAL_DMA_STATE_TIMEOUT;

        /* Process Unlocked */
        __HAL_UNLOCK(hdma);
        
        return HAL_TIMEOUT;
      }
    }
  }

  if(CompleteLevel == HAL_DMA_FULL_TRANSFER)
  {
    /* Multi_Buffering mode enabled */
    if(((hdma->Instance->CR) & (uint32_t)(DMA_SxCR_DBM)) != 0)
    {
      /* Clear the half transfer complete flag */
      __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_HT_FLAG_INDEX(hdma));
      /* Clear the transfer complete flag */
      __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_TC_FLAG_INDEX(hdma));

      /* Current memory buffer used is Memory 0 */
      if((hdma->Instance->CR & DMA_SxCR_CT) == 0)
      {
        /* Change DMA peripheral state */
//.........这里部分代码省略.........
开发者ID:196510921,项目名称:Balance_Car_STM32,代码行数:101,代码来源:stm32f4xx_hal_dma.c


示例2: HAL_GPIO_EXTI_Callback

/**
  * @brief  EXTI line detection callbacks.
  * @param  GPIO_Pin: Specifies the pins connected EXTI line
  * @retval None
  */
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
{
  static JOYState_TypeDef JoyState = JOY_NONE;
  static uint32_t debounce_time = 0;
  
  if(GPIO_Pin == GPIO_PIN_2)
  {    
    /* Get the Joystick State */
    JoyState = BSP_JOY_GetState();
    
    /* Clear joystick interrupt pending bits */
    BSP_IO_ITClear(JOY_ALL_PINS);
    
    if(audio_select_mode == AUDIO_SELECT_MENU)
    {  
      AUDIO_MenuProbeKey(JoyState); 
      
      switch(JoyState)
      {
      case JOY_LEFT:
        LCD_LOG_ScrollBack();
        break;
        
      case JOY_RIGHT:
        LCD_LOG_ScrollForward();
        break;          
        
      default:
        break;           
      }
    }
    else if(audio_select_mode == AUDIO_PLAYBACK_CONTROL)
    {
      AUDIO_PlaybackProbeKey(JoyState);
    }
  }
  
  if(audio_demo.state == AUDIO_DEMO_PLAYBACK)
  {
    if(GPIO_Pin == KEY_BUTTON_PIN)
    { 
      /* Prevent debounce effect for user key */
      if((HAL_GetTick() - debounce_time) > 50)
      {
        debounce_time = HAL_GetTick();
      }
      else
      {
        return;
      }
      
      /* Change the selection type */
      if(audio_select_mode == AUDIO_SELECT_MENU)
      {
        Audio_ChangeSelectMode(AUDIO_PLAYBACK_CONTROL); 
      }
      else if(audio_select_mode == AUDIO_PLAYBACK_CONTROL)
      {       
        Audio_ChangeSelectMode(AUDIO_SELECT_MENU);
      }
    }
  }
}
开发者ID:pierreroth64,项目名称:STM32Cube_FW_F4,代码行数:68,代码来源:menu.c


示例3: HAL_CAN_Transmit

/**
  * @brief  Initiates and transmits a CAN frame message.
  * @param  hcan: pointer to a CAN_HandleTypeDef structure that contains
  *         the configuration information for the specified CAN.  
  * @param  Timeout: Specify Timeout value   
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef* hcan, uint32_t Timeout)
{
  uint32_t  transmitmailbox = 5U;
  uint32_t tickstart = 0U;

  /* Check the parameters */
  assert_param(IS_CAN_IDTYPE(hcan->pTxMsg->IDE));
  assert_param(IS_CAN_RTR(hcan->pTxMsg->RTR));
  assert_param(IS_CAN_DLC(hcan->pTxMsg->DLC));

  if(((hcan->Instance->TSR&CAN_TSR_TME0) == CAN_TSR_TME0) || \
     ((hcan->Instance->TSR&CAN_TSR_TME1) == CAN_TSR_TME1) || \
     ((hcan->Instance->TSR&CAN_TSR_TME2) == CAN_TSR_TME2))
  {  
    /* Process locked */
    __HAL_LOCK(hcan);
  
    if(hcan->State == HAL_CAN_STATE_BUSY_RX) 
    {
      /* Change CAN state */
      hcan->State = HAL_CAN_STATE_BUSY_TX_RX;
    }
    else
    {
      /* Change CAN state */
      hcan->State = HAL_CAN_STATE_BUSY_TX;
    }
  
    /* Select one empty transmit mailbox */
    if ((hcan->Instance->TSR&CAN_TSR_TME0) == CAN_TSR_TME0)
    {
      transmitmailbox = 0U;
    }
    else if ((hcan->Instance->TSR&CAN_TSR_TME1) == CAN_TSR_TME1)
    {
      transmitmailbox = 1U;
    }
    else
    {
      transmitmailbox = 2U;
    }

    /* Set up the Id */
    hcan->Instance->sTxMailBox[transmitmailbox].TIR &= CAN_TI0R_TXRQ;
    if (hcan->pTxMsg->IDE == CAN_ID_STD)
    {
      assert_param(IS_CAN_STDID(hcan->pTxMsg->StdId));  
      hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->StdId << 21U) | \
                                                  hcan->pTxMsg->RTR);
    }
    else
    {
      assert_param(IS_CAN_EXTID(hcan->pTxMsg->ExtId));
      hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->ExtId << 3U) | \
                                                  hcan->pTxMsg->IDE | \
                                                  hcan->pTxMsg->RTR);
    }
    
    /* Set up the DLC */
    hcan->pTxMsg->DLC &= (uint8_t)0x0000000FU;
    hcan->Instance->sTxMailBox[transmitmailbox].TDTR &= (uint32_t)0xFFFFFFF0U;
    hcan->Instance->sTxMailBox[transmitmailbox].TDTR |= hcan->pTxMsg->DLC;

    /* Set up the data field */
    hcan->Instance->sTxMailBox[transmitmailbox].TDLR = (((uint32_t)hcan->pTxMsg->Data[3U] << 24U) | 
                                             ((uint32_t)hcan->pTxMsg->Data[2U] << 16U) |
                                             ((uint32_t)hcan->pTxMsg->Data[1U] << 8U) | 
                                             ((uint32_t)hcan->pTxMsg->Data[0U]));
    hcan->Instance->sTxMailBox[transmitmailbox].TDHR = (((uint32_t)hcan->pTxMsg->Data[7U] << 24U) | 
                                             ((uint32_t)hcan->pTxMsg->Data[6U] << 16U) |
                                             ((uint32_t)hcan->pTxMsg->Data[5U] << 8U) |
                                             ((uint32_t)hcan->pTxMsg->Data[4U]));
    /* Request transmission */
    hcan->Instance->sTxMailBox[transmitmailbox].TIR |= CAN_TI0R_TXRQ;
  
    /* Get tick */ 
    tickstart = HAL_GetTick();
  
    /* Check End of transmission flag */
    while(!(__HAL_CAN_TRANSMIT_STATUS(hcan, transmitmailbox)))
    {
      /* Check for the Timeout */
      if(Timeout != HAL_MAX_DELAY)
      {
       if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout))
       {
         hcan->State = HAL_CAN_STATE_TIMEOUT;
         /* Process unlocked */
         __HAL_UNLOCK(hcan);
         return HAL_TIMEOUT;
        }
      }
    }
//.........这里部分代码省略.........
开发者ID:kqzca,项目名称:prj,代码行数:101,代码来源:stm32f4xx_hal_can.c


示例4: HAL_NAND_Write_SpareArea

/**
  * @brief  Write Spare area(s) to NAND memory 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to source buffer to write  
  * @param  NumSpareAreaTowrite  : number of spare areas to write to block
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_SpareArea(NAND_HandleTypeDef *hnand, NAND_AddressTypedef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaTowrite)
{
  __IO uint32_t index = 0;
  uint32_t tickstart = 0;
  uint32_t deviceAddress = 0, numSpareAreaWritten = 0, nandAddress = 0, addressStatus = NAND_VALID_ADDRESS;

  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FMC_NAND_BANK2)
  {
    deviceAddress = NAND_DEVICE1;
  }
  else
  {
    deviceAddress = NAND_DEVICE2;
  }
  
  /* Update the FMC_NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* Spare area(s) write loop */
  while((NumSpareAreaTowrite != 0) && (addressStatus == NAND_VALID_ADDRESS))
  {  
    /* NAND raw address calculation */
    nandAddress = __ARRAY_ADDRESS(pAddress, hnand);
    
    /* Send write Spare area command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceAddress | CMD_AREA)) = NAND_CMD_AREA_C;
    *(__IO uint8_t *)((uint32_t)(deviceAddress | CMD_AREA)) = NAND_CMD_WRITE0;

    *(__IO uint8_t *)((uint32_t)(deviceAddress | ADDR_AREA)) = 0x00;  
    *(__IO uint8_t *)((uint32_t)(deviceAddress | ADDR_AREA)) = __ADDR_1st_CYCLE(nandAddress);  
    *(__IO uint8_t *)((uint32_t)(deviceAddress | ADDR_AREA)) = __ADDR_2nd_CYCLE(nandAddress);  
    *(__IO uint8_t *)((uint32_t)(deviceAddress | ADDR_AREA)) = __ADDR_3rd_CYCLE(nandAddress); 
  
    /* for 512 and 1 GB devices, 4th cycle is required */     
    if(hnand->Info.BlockNbr >= 1024)
    {
      *(__IO uint8_t *)((uint32_t)(deviceAddress | ADDR_AREA)) = __ADDR_4th_CYCLE(nandAddress);
    }
  
    /* Write data to memory */
    for(index = 0 ; index < hnand->Info.SpareAreaSize; index++)
    {
      *(__IO uint8_t *)deviceAddress = *(uint8_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceAddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
    
   
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
    
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      }   
    }

    /* Increment written spare areas number */
    numSpareAreaWritten++;
    
    /* Decrement spare areas to write */
    NumSpareAreaTowrite--;
    
    /* Increment the NAND address */
    HAL_NAND_Address_Inc(hnand, pAddress); 
      
  }

  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;

  /* Process unlocked */
  __HAL_UNLOCK(hnand);
    
  return HAL_OK;  
}
开发者ID:milspect18,项目名称:STM32F401_Code,代码行数:98,代码来源:stm32f4xx_hal_nand.c


示例5: HAL_SPDIFRX_ReceiveControlFlow_IT

/**
  * @brief Receive an amount of data (Control Flow) with Interrupt
  * @param hspdif: SPDIFRX handle
  * @param pData: a 32-bit pointer to the Receive data buffer.
  * @param Size: number of data sample (Control Flow) to be received :
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SPDIFRX_ReceiveControlFlow_IT(SPDIFRX_HandleTypeDef *hspdif, uint32_t *pData, uint16_t Size)
{
  uint32_t tickstart = 0U;
  
  if((hspdif->State == HAL_SPDIFRX_STATE_READY) || (hspdif->State == HAL_SPDIFRX_STATE_BUSY_RX))
  {
    if((pData == NULL ) || (Size == 0U)) 
    {
      return HAL_ERROR;
    }
    
    /* Process Locked */
    __HAL_LOCK(hspdif);
    
    hspdif->pCsBuffPtr = pData;
    hspdif->CsXferSize = Size;
    hspdif->CsXferCount = Size;
    
    hspdif->ErrorCode = HAL_SPDIFRX_ERROR_NONE;
    
    /* Check if a receive process is ongoing or not */
    hspdif->State = HAL_SPDIFRX_STATE_BUSY_CX;
    
    
    /* Enable the SPDIFRX PE Error Interrupt */
    __HAL_SPDIFRX_ENABLE_IT(hspdif, SPDIFRX_IT_PERRIE);
    
    /* Enable the SPDIFRX OVR Error Interrupt */
    __HAL_SPDIFRX_ENABLE_IT(hspdif, SPDIFRX_IT_OVRIE);
    
    /* Process Unlocked */
    __HAL_UNLOCK(hspdif);
    
    /* Enable the SPDIFRX CSRNE interrupt */
    __HAL_SPDIFRX_ENABLE_IT(hspdif, SPDIFRX_IT_CSRNE);
    
    if (((SPDIFRX->CR & SPDIFRX_CR_SPDIFEN) != SPDIFRX_STATE_SYNC) || ((SPDIFRX->CR & SPDIFRX_CR_SPDIFEN) != 0x00U)) 
    {
      /* Start synchronization */
      __HAL_SPDIFRX_SYNC(hspdif);
      
      /* Get tick */ 
      tickstart = HAL_GetTick();
      
      /* Wait until SYNCD flag is set */
      if(SPDIFRX_WaitOnFlagUntilTimeout(hspdif, SPDIFRX_FLAG_SYNCD, RESET, SPDIFRX_TIMEOUT_VALUE, tickstart) != HAL_OK)
      { 
        return HAL_TIMEOUT;
      }  
      
      /* Start reception */    
      __HAL_SPDIFRX_RCV(hspdif);
    }
    
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY; 
  }
}
开发者ID:DTFUHF,项目名称:betaflight,代码行数:68,代码来源:stm32f7xx_hal_spdifrx.c


示例6: HAL_PCDEx_BCD_VBUSDetect

/**
  * @brief  Handle BatteryCharging Process.
  * @param  hpcd: PCD handle
  * @retval HAL status
  */
void HAL_PCDEx_BCD_VBUSDetect(PCD_HandleTypeDef *hpcd)
{
  USB_OTG_GlobalTypeDef *USBx = hpcd->Instance;  
  uint32_t tickstart = HAL_GetTick();
  
  /* Start BCD When device is connected */
  if (USBx_DEVICE->DCTL & USB_OTG_DCTL_SDIS)
  { 
    /* Enable DCD : Data Contact Detect */
    USBx->GCCFG |= USB_OTG_GCCFG_DCDEN;
    
    /* Wait Detect flag or a timeout is happen*/
    while ((USBx->GCCFG & USB_OTG_GCCFG_DCDET) == 0)
    {
      /* Check for the Timeout */
      if((HAL_GetTick() - tickstart ) > 1000)
      {
        HAL_PCDEx_BCD_Callback(hpcd, PCD_BCD_ERROR);
        return;
      }
    }
    
    /* Right response got */
    HAL_Delay(100); 
    
    /* Check Detect flag*/
    if (USBx->GCCFG & USB_OTG_GCCFG_DCDET)
    {
      HAL_PCDEx_BCD_Callback(hpcd, PCD_BCD_CONTACT_DETECTION);
    }
    
    /*Primary detection: checks if connected to Standard Downstream Port  
    (without charging capability) */
    USBx->GCCFG &=~ USB_OTG_GCCFG_DCDEN;
    USBx->GCCFG |=  USB_OTG_GCCFG_PDEN;
    HAL_Delay(100); 
    
    if (!(USBx->GCCFG & USB_OTG_GCCFG_PDET))
    {
      /* Case of Standard Downstream Port */
      HAL_PCDEx_BCD_Callback(hpcd, PCD_BCD_STD_DOWNSTREAM_PORT);
    }
    else  
    {
      /* start secondary detection to check connection to Charging Downstream 
      Port or Dedicated Charging Port */
      USBx->GCCFG &=~ USB_OTG_GCCFG_PDEN;
      USBx->GCCFG |=  USB_OTG_GCCFG_SDEN;
      HAL_Delay(100); 
      
      if ((USBx->GCCFG) & USB_OTG_GCCFG_SDET)
      { 
        /* case Dedicated Charging Port  */
        HAL_PCDEx_BCD_Callback(hpcd, PCD_BCD_DEDICATED_CHARGING_PORT);
      }
      else
      {
        /* case Charging Downstream Port  */
        HAL_PCDEx_BCD_Callback(hpcd, PCD_BCD_CHARGING_DOWNSTREAM_PORT);
      }
    }
    /* Battery Charging capability discovery finished */
    HAL_PCDEx_BCD_Callback(hpcd, PCD_BCD_DISCOVERY_COMPLETED);
  }
}
开发者ID:Archcady,项目名称:mbed-os,代码行数:70,代码来源:stm32l4xx_hal_pcd_ex.c


示例7: HAL_DMA_PollForTransfer

/**
  * @brief  Polling for transfer complete.
  * @param  hdma:          pointer to a DMA_HandleTypeDef structure that contains
  *                        the configuration information for the specified DMA Stream.
  * @param  CompleteLevel: Specifies the DMA level complete.
  * @note   The polling mode is kept in this version for legacy. it is recommanded to use the IT model instead.
  *         This model could be used for debug purpose.
  * @note   The HAL_DMA_PollForTransfer API cannot be used in circular and double buffering mode (automatic circular mode). 
  * @param  Timeout:       Timeout duration.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, HAL_DMA_LevelCompleteTypeDef CompleteLevel, uint32_t Timeout)
{
  HAL_StatusTypeDef status = HAL_OK; 
  uint32_t temp;
  uint32_t tickstart = HAL_GetTick(); 
  uint32_t tmpisr;
  
  /* calculate DMA base and stream number */
  DMA_Base_Registers *regs;
  
  /* Polling mode not supported in circular mode and double buffering mode */
  if ((hdma->Instance->CR & DMA_SxCR_CIRC) != RESET)
  {
    hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED;
    return HAL_ERROR;
  }
  
  /* Get the level transfer complete flag */
  if(CompleteLevel == HAL_DMA_FULL_TRANSFER)
  {
    /* Transfer Complete flag */
    temp = DMA_FLAG_TCIF0_4 << hdma->StreamIndex;
  }
  else
  {
    /* Half Transfer Complete flag */
    temp = DMA_FLAG_HTIF0_4 << hdma->StreamIndex;
  }
  
  regs = (DMA_Base_Registers *)hdma->StreamBaseAddress;
  tmpisr = regs->ISR;
  
  while((tmpisr & temp) == RESET )
  {
    /* Check for the Timeout (Not applicable in circular mode)*/
    if(Timeout != HAL_MAX_DELAY)
    {
      if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
      {
        /* Update error code */
        hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT;

        /* Process Unlocked */
        __HAL_UNLOCK(hdma);
        
        /* Change the DMA state */
        hdma->State = HAL_DMA_STATE_READY;
        
        return HAL_TIMEOUT;
      }
    }
    
    if((tmpisr & (DMA_FLAG_TEIF0_4 << hdma->StreamIndex)) != RESET)
    {
      /* Update error code */
      hdma->ErrorCode |= HAL_DMA_ERROR_TE;
      
      /* Clear the transfer error flag */
      regs->IFCR = DMA_FLAG_TEIF0_4 << hdma->StreamIndex;
    }
    
    if((tmpisr & (DMA_FLAG_FEIF0_4 << hdma->StreamIndex)) != RESET)
    {
      /* Update error code */
      hdma->ErrorCode |= HAL_DMA_ERROR_FE;
      
      /* Clear the FIFO error flag */
      regs->IFCR = DMA_FLAG_FEIF0_4 << hdma->StreamIndex;
    }
    
    if((tmpisr & (DMA_FLAG_DMEIF0_4 << hdma->StreamIndex)) != RESET)
    {
      /* Update error code */
      hdma->ErrorCode |= HAL_DMA_ERROR_DME;
      
      /* Clear the Direct Mode error flag */
      regs->IFCR = DMA_FLAG_DMEIF0_4 << hdma->StreamIndex;
    }
  }
  
  if(hdma->ErrorCode != HAL_DMA_ERROR_NONE)
  {
    if((hdma->ErrorCode & HAL_DMA_ERROR_TE) != RESET)
    {
      HAL_DMA_Abort(hdma);
    
      /* Clear the half transfer and transfer complete flags */
      regs->IFCR = (DMA_FLAG_HTIF0_4 | DMA_FLAG_TCIF0_4) << hdma->StreamIndex;
    
//.........这里部分代码省略.........
开发者ID:ryankurte,项目名称:stm32f4-base,代码行数:101,代码来源:stm32f7xx_hal_dma.c


示例8: HAL_NAND_Erase_Block

/**
  * @brief  NAND memory Block erase 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress: pointer to NAND address structure
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Erase_Block(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress)
{
  uint32_t deviceaddress = 0;
  uint32_t tickstart = 0;
  
  /* Process Locked */
  __HAL_LOCK(hnand);
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* Send Erase block command sequence */
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE0;

  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  
  /* for 512 and 1 GB devices, 4th cycle is required */     
  if(hnand->Info.BlockNbr >= 1024)
  {
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_4TH_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  }  
		
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE1; 
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Get tick */
  tickstart = HAL_GetTick();
  
  /* Read status until NAND is ready */
  while(HAL_NAND_Read_Status(hnand) != NAND_READY)
  {
    if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
    {
  /* Process unlocked */
  __HAL_UNLOCK(hnand);    
  
      return HAL_TIMEOUT; 
    } 
}

  /* Process unlocked */
  __HAL_UNLOCK(hnand);    
  
  return HAL_OK;  
}
开发者ID:AlessandroA,项目名称:mbed,代码行数:72,代码来源:stm32f3xx_hal_nand.c


示例9: HAL_DMA_PollForTransfer

/**
  * @brief  Polling for transfer complete.
  * @param  hdma:    pointer to a DMA_HandleTypeDef structure that contains
  *                  the configuration information for the specified DMA Channel.
  * @param  CompleteLevel: Specifies the DMA level complete.  
  * @param  Timeout:       Timeout duration.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout)
{
  uint32_t temp;
  uint32_t tickstart = 0x00;
  
  /* Get the level transfer complete flag */
  if(CompleteLevel == HAL_DMA_FULL_TRANSFER)
  {
    /* Transfer Complete flag */
    temp = __HAL_DMA_GET_TC_FLAG_INDEX(hdma);
  }
  else
  {
    /* Half Transfer Complete flag */
    temp = __HAL_DMA_GET_HT_FLAG_INDEX(hdma);
  }

  /* Get tick */
  tickstart = HAL_GetTick();

  while(__HAL_DMA_GET_FLAG(hdma, temp) == RESET)
  {
    if((__HAL_DMA_GET_FLAG(hdma, __HAL_DMA_GET_TE_FLAG_INDEX(hdma)) != RESET))
    {      
      /* Clear the transfer error flags */
      __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_TE_FLAG_INDEX(hdma));
      
      /* Update error code */
      SET_BIT(hdma->ErrorCode, HAL_DMA_ERROR_TE);

      /* Change the DMA state */
      hdma->State= HAL_DMA_STATE_ERROR;
      
      /* Process Unlocked */
      __HAL_UNLOCK(hdma);
      
      return HAL_ERROR;
    }
    /* Check for the Timeout */
    if(Timeout != HAL_MAX_DELAY)
    {
      if((Timeout == 0) || ((HAL_GetTick() - tickstart) > Timeout))
      {
        /* Update error code */
        SET_BIT(hdma->ErrorCode, HAL_DMA_ERROR_TIMEOUT);
        
        /* Change the DMA state */
        hdma->State = HAL_DMA_STATE_TIMEOUT;

        /* Process Unlocked */
        __HAL_UNLOCK(hdma);
        
        return HAL_TIMEOUT;
      }
    }
  }

  if(CompleteLevel == HAL_DMA_FULL_TRANSFER)
  {
    /* Clear the transfer complete flag */
    __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_TC_FLAG_INDEX(hdma));

    /* The selected Channelx EN bit is cleared (DMA is disabled and 
    all transfers are complete) */
    hdma->State = HAL_DMA_STATE_READY;

  }
  else
  { 
    /* Clear the half transfer complete flag */
    __HAL_DMA_CLEAR_FLAG(hdma, __HAL_DMA_GET_HT_FLAG_INDEX(hdma));
  
    /* The selected Channelx EN bit is cleared (DMA is disabled and 
    all transfers of half buffer are complete) */
    hdma->State = HAL_DMA_STATE_READY_HALF;
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hdma);

  return HAL_OK;
}
开发者ID:Bluebear233,项目名称:rt-thread-stm32f103,代码行数:90,代码来源:stm32f1xx_hal_dma.c


示例10: HAL_DMA_PollForTransfer

/**
  * @brief  Polling for transfer complete.
  * @param  hdma:    pointer to a DMA_HandleTypeDef structure that contains
  *                  the configuration information for the specified DMA Channel.
  * @param  CompleteLevel: Specifies the DMA level complete.
  * @param  Timeout:       Timeout duration.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout)
{
  uint32_t temp;
  uint32_t tickstart = 0;

  if(HAL_DMA_STATE_BUSY != hdma->State)
  {
    /* no transfer ongoing */
    hdma->ErrorCode = HAL_DMA_ERROR_NO_XFER;

    return HAL_ERROR;
  }

  /* Polling mode not supported in circular mode */
  if (RESET != (hdma->Instance->CCR & DMA_CCR_CIRC))
  {
    hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED;
    return HAL_ERROR;
  }
  
  /* Get the level transfer complete flag */
  if (HAL_DMA_FULL_TRANSFER == CompleteLevel)
  {
    /* Transfer Complete flag */
    temp = DMA_FLAG_TC1 << hdma->ChannelIndex;
  }
  else
  {
    /* Half Transfer Complete flag */
    temp = DMA_FLAG_HT1 << hdma->ChannelIndex;
  }

  /* Get tick */
  tickstart = HAL_GetTick();

  while(RESET == (hdma->DmaBaseAddress->ISR & temp))     
  {
    if((RESET != (hdma->DmaBaseAddress->ISR & (DMA_FLAG_TE1 << hdma->ChannelIndex))))    
    {
      /* When a DMA transfer error occurs */
      /* A hardware clear of its EN bits is performed */
      /* Clear all flags */
      hdma->DmaBaseAddress->IFCR = (DMA_ISR_GIF1 << hdma->ChannelIndex);

      /* Update error code */
      hdma->ErrorCode = HAL_DMA_ERROR_TE;

      /* Change the DMA state */
      hdma->State= HAL_DMA_STATE_READY;

      /* Process Unlocked */
      __HAL_UNLOCK(hdma);

      return HAL_ERROR;
    }
    /* Check for the Timeout */
    if(Timeout != HAL_MAX_DELAY)
    {
      if((Timeout == 0) || ((HAL_GetTick() - tickstart) > Timeout))
      {
        /* Update error code */
        hdma->ErrorCode = HAL_DMA_ERROR_TIMEOUT;

        /* Change the DMA state */
        hdma->State = HAL_DMA_STATE_READY;
        
        /* Process Unlocked */
        __HAL_UNLOCK(hdma);

        return HAL_ERROR;
      }
    }
  }

  if(HAL_DMA_FULL_TRANSFER == CompleteLevel)
  {
    /* Clear the transfer complete flag */
    hdma->DmaBaseAddress->IFCR = (DMA_FLAG_TC1 << hdma->ChannelIndex);

    /* The selected Channelx EN bit is cleared (DMA is disabled and
    all transfers are complete) */
    hdma->State = HAL_DMA_STATE_READY;
  }
  else
  {
    /* Clear the half transfer complete flag */
    hdma->DmaBaseAddress->IFCR = (DMA_FLAG_HT1 << hdma->ChannelIndex);
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hdma);  

//.........这里部分代码省略.........
开发者ID:sunkaizhu,项目名称:zephyr,代码行数:101,代码来源:stm32l4xx_hal_dma.c


示例11: HAL_NAND_Write_SpareArea

/**
  * @brief  Write Spare area(s) to NAND memory 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress: pointer to NAND address structure
  * @param  pBuffer: pointer to source buffer to write  
  * @param  NumSpareAreaTowrite: number of spare areas to write to block
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_SpareArea(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaTowrite)
{
  __IO uint32_t index = 0;
  uint32_t tickstart = 0;
  uint32_t deviceaddress = 0, size = 0, num_spare_area_written = 0, addressstatus = NAND_VALID_ADDRESS;
  NAND_AddressTypeDef nandaddress;
  uint32_t addressoffset = 0;

  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the FMC_NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;

  /* Save the content of pAddress as it will be modified */
  nandaddress.Block     = pAddress->Block;
  nandaddress.Page      = pAddress->Page;
  nandaddress.Zone      = pAddress->Zone;
  
  /* Spare area(s) write loop */
  while((NumSpareAreaTowrite != 0) && (addressstatus == NAND_VALID_ADDRESS))
  {  
    /* update the buffer size */
    size = (hnand->Info.SpareAreaSize) + ((hnand->Info.SpareAreaSize) * num_spare_area_written);

    /* Get the address offset */
    addressoffset = ARRAY_ADDRESS(&nandaddress, hnand);

    /* Send write Spare area command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;

    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;  
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(addressoffset);  
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(addressoffset);  
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(addressoffset); 
  
    /* for 512 and 1 GB devices, 4th cycle is required */     
    if(hnand->Info.BlockNbr >= 1024)
    {
      *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_4TH_CYCLE(addressoffset);
    }
  
    /* Write data to memory */
    for(; index < size; index++)
    {
      *(__IO uint8_t *)deviceaddress = *(uint8_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
    
    /* Get tick */
    tickstart = HAL_GetTick();
   
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      } 
    }

    /* Increment written spare areas number */
    num_spare_area_written++;
    
    /* Decrement spare areas to write */
    NumSpareAreaTowrite--;
    
    /* Increment the NAND address */
    addressstatus = NAND_AddressIncrement(hnand, &nandaddress);
  }

  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
//.........这里部分代码省略.........
开发者ID:AlessandroA,项目名称:mbed,代码行数:101,代码来源:stm32f3xx_hal_nand.c


示例12: HAL_DAC_ConfigChannel

/**
  * @brief  Configures the selected DAC channel.
  * @param  hdac: pointer to a DAC_HandleTypeDef structure that contains
  *         the configuration information for the specified DAC.
  * @param  sConfig: DAC configuration structure.
  * @param  Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_CHANNEL_1: DAC Channel1 selected
  *            @arg DAC_CHANNEL_2: DAC Channel2 selected
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DAC_ConfigChannel(DAC_HandleTypeDef* hdac, DAC_ChannelConfTypeDef* sConfig, uint32_t Channel)
{
  uint32_t tmpreg1 = 0, tmpreg2 = 0;
  uint32_t tickstart = 0;
   
  /* Check the DAC parameters */
  assert_param(IS_DAC_TRIGGER(sConfig->DAC_Trigger));
  assert_param(IS_DAC_OUTPUT_BUFFER_STATE(sConfig->DAC_OutputBuffer));
  assert_param(IS_DAC_CHIP_CONNECTION(sConfig->DAC_ConnectOnChipPeripheral));
  assert_param(IS_DAC_TRIMMING(sConfig->DAC_UserTrimming));
  if ((sConfig->DAC_UserTrimming) == DAC_TRIMMING_USER)
  {
    assert_param(IS_DAC_TRIMMINGVALUE(sConfig->DAC_TrimmingValue));               
  }
  assert_param(IS_DAC_SAMPLEANDHOLD(sConfig->DAC_SampleAndHold));
  if ((sConfig->DAC_SampleAndHold) == DAC_SAMPLEANDHOLD_ENABLE)
  {
    assert_param(IS_DAC_SAMPLETIME(sConfig->DAC_SampleAndHoldConfig.DAC_SampleTime));
    assert_param(IS_DAC_HOLDTIME(sConfig->DAC_SampleAndHoldConfig.DAC_HoldTime));
    assert_param(IS_DAC_REFRESHTIME(sConfig->DAC_SampleAndHoldConfig.DAC_RefreshTime)); 
  }
  assert_param(IS_DAC_CHANNEL(Channel));
 
  /* Process locked */
  __HAL_LOCK(hdac);
  
  /* Change DAC state */
  hdac->State = HAL_DAC_STATE_BUSY;
  
  if(sConfig->DAC_SampleAndHold == DAC_SAMPLEANDHOLD_ENABLE)
  /* Sample on old configuration */ 
  {
    /* SampleTime */
    if (Channel == DAC_CHANNEL_1)
    {
      /* Get timeout */
      tickstart = HAL_GetTick();
      
      /* SHSR1 can be written when BWST1  equals RESET */
      while (((hdac->Instance->SR) & DAC_SR_BWST1)!= RESET)
      {
        /* Check for the Timeout */
        if((HAL_GetTick() - tickstart) > TIMEOUT_DAC_CALIBCONFIG)
        {
          /* Update error code */
          SET_BIT(hdac->ErrorCode, HAL_DAC_ERROR_TIMEOUT);

          /* Change the DMA state */
          hdac->State = HAL_DAC_STATE_TIMEOUT;

          return HAL_TIMEOUT;
        }
      }
      HAL_Delay(1);
      hdac->Instance->SHSR1 = sConfig->DAC_SampleAndHoldConfig.DAC_SampleTime;
    }
    else /* Channel 2 */
    {
      /* SHSR2 can be written when BWST2 equals RESET */

      while (((hdac->Instance->SR) & DAC_SR_BWST2)!= RESET)
      {
        /* Check for the Timeout */
        if((HAL_GetTick() - tickstart) > TIMEOUT_DAC_CALIBCONFIG)
        {
          /* Update error code */
          SET_BIT(hdac->ErrorCode, HAL_DAC_ERROR_TIMEOUT);

          /* Change the DMA state */
          hdac->State = HAL_DAC_STATE_TIMEOUT;

          return HAL_TIMEOUT;
        }
      }
      HAL_Delay(1);
      hdac->Instance->SHSR2 = sConfig->DAC_SampleAndHoldConfig.DAC_SampleTime;
    }
    /* HoldTime */
    hdac->Instance->SHHR = (sConfig->DAC_SampleAndHoldConfig.DAC_HoldTime)<<Channel;
    /* RefreshTime */
    hdac->Instance->SHRR = (sConfig->DAC_SampleAndHoldConfig.DAC_RefreshTime)<<Channel;
  }
    
  if(sConfig->DAC_UserTrimming == DAC_TRIMMING_USER)
  /* USER TRIMMING */
  {
  /* Get the DAC CCR value */
  tmpreg1 = hdac->Instance->CCR;
  /* Clear trimming value */
//.........这里部分代码省略.........
开发者ID:zbrozek,项目名称:mc-logic_1-0,代码行数:101,代码来源:stm32l4xx_hal_dac.c


示例13: HAL_ADCEx_InjectedPollForConversion

/**
  * @brief  Wait for injected group conversion to be completed.
  * @param  hadc: ADC handle
  * @param  Timeout: Timeout value in millisecond.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ADCEx_InjectedPollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout)
{
  uint32_t tickstart;

  /* Variables for polling in case of scan mode enabled and polling for each  */
  /* conversion.                                                              */
  __IO uint32_t Conversion_Timeout_CPU_cycles = 0;
  uint32_t Conversion_Timeout_CPU_cycles_max = 0;
  
  /* Check the parameters */
  assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));

  /* Get timeout */
  tickstart = HAL_GetTick();  
     
  /* Polling for end of conversion: differentiation if single/sequence        */
  /* conversion.                                                              */
  /* For injected group, flag JEOC is set only at the end of the sequence,    */
  /* not for each conversion within the sequence.                             */
  /*  - If single conversion for injected group (scan mode disabled or        */
  /*    InjectedNbrOfConversion ==1), flag jEOC is used to determine the      */
  /*    conversion completion.                                                */
  /*  - If sequence conversion for injected group (scan mode enabled and      */
  /*    InjectedNbrOfConversion >=2), flag JEOC is set only at the end of the */
  /*    sequence.                                                             */
  /*    To poll for each conversion, the maximum conversion time is computed  */
  /*    from ADC conversion time (selected sampling time + conversion time of */
  /*    12.5 ADC clock cycles) and APB2/ADC clock prescalers (depending on    */
  /*    settings, conversion time range can be from 28 to 32256 CPU cycles).  */
  if ((hadc->Instance->JSQR & ADC_JSQR_JL) == RESET)
  {
    /* Wait until End of Conversion flag is raised */
    while(HAL_IS_BIT_CLR(hadc->Instance->SR, ADC_FLAG_JEOC))
    {
      /* Check if timeout is disabled (set to infinite wait) */
      if(Timeout != HAL_MAX_DELAY)
      {
        if((Timeout == 0) || ((HAL_GetTick() - tickstart ) > Timeout))
        {
          /* Update ADC state machine to timeout */
          hadc->State = HAL_ADC_STATE_TIMEOUT;
          
          /* Process unlocked */
          __HAL_UNLOCK(hadc);
          
          return HAL_ERROR;
        }
      }
    }
  }
  else
  {
    /* Poll with maximum conversion time */
    /*  - Computation of CPU clock cycles corresponding to ADC clock cycles   */
    /*    and ADC maximum conversion cycles on all channels.                  */
    /*  - Wait for the expected ADC clock cycles delay                        */
    Conversion_Timeout_CPU_cycles_max = ((SystemCoreClock
                                          / HAL_RCCEx_GetPeriphCLKFreq(RCC_PERIPHCLK_ADC))
                                         * ADC_CONVCYCLES_MAX_RANGE(hadc)                 );

    while(Conversion_Timeout_CPU_cycles < Conversion_Timeout_CPU_cycles_max)
    {
      /* Check if timeout is disabled (set to infinite wait) */
      if(Timeout != HAL_MAX_DELAY)
      {
        if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
        {
          /* Update ADC state machine to timeout */
          hadc->State = HAL_ADC_STATE_TIMEOUT;

          /* Process unlocked */
          __HAL_UNLOCK(hadc);
          
          return HAL_ERROR;
        }
      }
      Conversion_Timeout_CPU_cycles ++;
    }
  }

  /* Clear injected group conversion flag (and regular conversion flag raised */
  /* simultaneously)                                                          */
  __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_JSTRT | ADC_FLAG_JEOC | ADC_FLAG_EOC);
  
  /* Update state machine on conversion status if not in error state */
  if(hadc->State != HAL_ADC_STATE_ERROR)
  {
    /* Update ADC state machine */
    if(hadc->State != HAL_ADC_STATE_EOC_INJ_REG)
    {

      if(hadc->State == HAL_ADC_STATE_EOC_REG)
      {
        /* Change ADC state */
//.........这里部分代码省略.........
开发者ID:12019,项目名称:USB_Photoframe,代码行数:101,代码来源:stm32f1xx_hal_adc_ex.c


示例14: HAL_ADCEx_Calibration_Start

/**
  * @brief  Perform an ADC automatic self-calibration
  *         Calibration prerequisite: ADC must be disabled (execute this
  *         function before HAL_ADC_Start() or after HAL_ADC_Stop() ).
  *         During calibration process, ADC is enabled. ADC is let enabled at
  *         the completion of this function.
  * @param  hadc: ADC handle
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ADCEx_Calibration_Start(ADC_HandleTypeDef* hadc)
{
  HAL_StatusTypeDef tmp_hal_status = HAL_OK;
  uint32_t tickstart;
  __IO uint32_t wait_loop_index = 0;
  
  /* Check the parameters */
  assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));

  /* Process locked */
  __HAL_LOCK(hadc);
    
  /* 1. Calibration prerequisite:                                             */
  /*    - ADC must be disabled for at least two ADC clock cycles in disable   */
  /*      mode before ADC enable                                              */
  /* Stop potential conversion on going, on regular and injected groups       */
  /* Disable ADC peripheral */
  tmp_hal_status = ADC_ConversionStop_Disable(hadc);
  
  /* Check if ADC is effectively disabled */
  if (tmp_hal_status != HAL_ERROR)
  {
    /* Hardware prerequisite: delay before starting the calibration.          */
    /*  - Computation of CPU clock cycles corresponding to ADC clock cycles.  */
    /*  - Wait for the expected ADC clock cycles delay */
    wait_loop_index = ((SystemCoreClock
                        / HAL_RCCEx_GetPeriphCLKFreq(RCC_PERIPHCLK_ADC))
                       * ADC_PRECALIBRATION_DELAY_ADCCLOCKCYCLES        );

    while(wait_loop_index != 0)
    {
      wait_loop_index--;
    }
    
    /* 2. Enable the ADC peripheral */
    ADC_Enable(hadc);
    

    /* 3. Resets ADC calibration registers */  
    SET_BIT(hadc->Instance->CR2, ADC_CR2_RSTCAL);
    
    tickstart = HAL_GetTick();  

    /* Wait for calibration reset completion */
    while(HAL_IS_BIT_SET(hadc->Instance->CR2, ADC_CR2_RSTCAL))
    {
      if((HAL_GetTick() - tickstart) > ADC_CALIBRATION_TIMEOUT)
      {
        /* Update ADC state machine to error */
        hadc->State = HAL_ADC_STATE_ERROR;
        
        /* Process unlocked */
        __HAL_UNLOCK(hadc);
        
        return HAL_ERROR;
      }
    }
    
    
    /* 4. Start ADC calibration */
    SET_BIT(hadc->Instance->CR2, ADC_CR2_CAL);
    
    tickstart = HAL_GetTick();  

    /* Wait for calibration completion */
    while(HAL_IS_BIT_SET(hadc->Instance->CR2, ADC_CR2_CAL))
    {
      if((HAL_GetTick() - tickstart) > ADC_CALIBRATION_TIMEOUT)
      {
        /* Update ADC state machine to error */
        hadc->State = HAL_ADC_STATE_ERROR;
        
        /* Process unlocked */
        __HAL_UNLOCK(hadc);
        
        return HAL_ERROR;
      }
    }
    
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hadc);
  
  /* Return function status */
  return tmp_hal_status;
}
开发者ID:12019,项目名称:USB_Photoframe,代码行数:96,代码来源:stm32f1xx_hal_adc_ex.c


示例15: HAL_CEC_Receive

/**
  * @brief Receive data in blocking mode. 
  * @param hcec: CEC handle
  * @param pData: pointer to received data buffer.
  * @param Timeout: Timeout duration.
  * @note  The received data size is not known beforehand, the latter is known
  *        when the reception is complete and is stored in hcec->RxXferSize.  
  *        hcec->RxXferSize is the sum of opcodes + operands (0 to 14 operands max).
  *        If only a header is received, hcec->RxXferSize = 0    
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_CEC_Receive(CEC_HandleTypeDef *hcec, uint8_t *pData, uint32_t Timeout)
{
  uint32_t temp = 0;
  uint32_t tickstart = 0;   

  if(hcec->State == HAL_CEC_STATE_READY)
  {
    if(pData == NULL) 
    {
      return HAL_ERROR;
    }
    
    /* When a ping is received, RxXferSize is 0*/
    /* When a message is received, RxXferSize contains the number of received bytes */
    hcec->RxXferSize = CEC_RXXFERSIZE_INITIALIZE; 
    
    /* Process Locked */
    __HAL_LOCK(hcec);

    hcec->ErrorCode = HAL_CEC_ERROR_NONE;
    
    /* Continue the reception until the End Of Message is received (CEC_FLAG_REOM) */
    do
    {
      /* Timeout handling */
      tickstart = HAL_GetTick();
      
      /* Wait for next byte to be received */
      while (HAL_IS_BIT_CLR(hcec->Instance->CSR, CEC_FLAG_RBTF))
      {
        /* Timeout handling */
        if(Timeout != HAL_MAX_DELAY)
        {
          if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout))
          {
            hcec->State = HAL_CEC_STATE_READY;
            __HAL_UNLOCK(hcec);    
            return HAL_TIMEOUT;
          }
        }
        
        /* Check if an error occured during the reception */
        if(HAL_IS_BIT_SET(hcec->Instance->CSR, CEC_FLAG_RERR))
        {
          /* Copy ESR for error handling purposes */
          hcec->ErrorCode = READ_BIT(hcec->Instance->ESR, CEC_ESR_ALL_ERROR);
          
          /* Acknowledgement of the error */
          __HAL_CEC_CLEAR_FLAG(hcec, CEC_FLAG_RERR);
          
          hcec->State = HAL_CEC_STATE_READY;
          __HAL_UNLOCK(hcec);
          return  HAL_ERROR;
        }
      }
      
      /* Keep the value of CSR register as the register is cleared during reception process */
      temp = hcec->Instance->CSR;
      
      /* Read received data */
      *pData++ = hcec->Instance->RXD;
      
      /* Acknowledge received byte by writing 0x00 */
      CLEAR_BIT(hcec->Instance->CSR, CEC_FLAG_RECEIVE_MASK);
      
       

鲜花

握手

雷人

路过

鸡蛋
该文章已有0人参与评论

请发表评论

全部评论

专题导读
上一篇:
C++ HAL_HCD_GetCurrentFrame函数代码示例发布时间:2022-05-30
下一篇:
C++ HAL_GetREVID函数代码示例发布时间:2022-05-30
热门推荐
阅读排行榜

扫描微信二维码

查看手机版网站

随时了解更新最新资讯

139-2527-9053

在线客服(服务时间 9:00~18:00)

在线QQ客服
地址:深圳市南山区西丽大学城创智工业园
电邮:jeky_zhao#qq.com
移动电话:139-2527-9053

Powered by 互联科技 X3.4© 2001-2213 极客世界.|Sitemap