/***************************************************************************//**
 * @brief
 *   Sets the drive mode for a GPIO port.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] mode
 *   Drive mode to use for port.
 ******************************************************************************/
void GPIO_DriveModeSet(GPIO_Port_TypeDef port, GPIO_DriveMode_TypeDef mode)
{
  EFM_ASSERT(GPIO_PORT_VALID(port) && GPIO_DRIVEMODE_VALID(mode));

  GPIO->P[port].CTRL = (GPIO->P[port].CTRL & ~(_GPIO_P_CTRL_DRIVEMODE_MASK))
                       | (mode << _GPIO_P_CTRL_DRIVEMODE_SHIFT);
}

/***************************************************************************//**
 * @brief
 *   Sets the drive strength for a GPIO port.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] strength
 *   Drive strength to use for port.
 ******************************************************************************/
void GPIO_DriveStrengthSet(GPIO_Port_TypeDef port,
                           GPIO_DriveStrength_TypeDef strength)
{
  EFM_ASSERT(GPIO_PORT_VALID(port) && GPIO_STRENGHT_VALID(strength));
  BUS_RegMaskedWrite(&GPIO->P[port].CTRL,
                     _GPIO_P_CTRL_DRIVESTRENGTH_MASK | _GPIO_P_CTRL_DRIVESTRENGTHALT_MASK,
                     strength);
}

/***************************************************************************//**
 * @brief
 *   Set the mode for a GPIO pin.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] pin
 *   The pin number in the port.
 *
 * @param[in] mode
 *   The desired pin mode.
 *
 * @param[in] out
 *   Value to set for pin in DOUT register. The DOUT setting is important for
 *   even some input mode configurations, determining pull-up/down direction.
 ******************************************************************************/
void GPIO_PinModeSet(GPIO_Port_TypeDef port,
                     unsigned int pin,
                     GPIO_Mode_TypeDef mode,
                     unsigned int out)
{
  EFM_ASSERT(GPIO_PORT_VALID(port) && GPIO_PIN_VALID(pin));

  /* If disabling pin, do not modify DOUT in order to reduce chance for */
  /* glitch/spike (may not be sufficient precaution in all use cases) */
  if (mode != gpioModeDisabled)
  {
    if (out)
    {
      GPIO->P[port].DOUTSET = 1 << pin;
    }
    else
    {
      GPIO->P[port].DOUTCLR = 1 << pin;
    }
  }

  /* There are two registers controlling the pins for each port. The MODEL
   * register controls pins 0-7 and MODEH controls pins 8-15. */
  if (pin < 8)
  {
    GPIO->P[port].MODEL = (GPIO->P[port].MODEL & ~(0xF << (pin * 4))) |
                          (mode << (pin * 4));
  }
  else
  {
    GPIO->P[port].MODEH = (GPIO->P[port].MODEH & ~(0xF << ((pin - 8) * 4))) |
                          (mode << ((pin - 8) * 4));
  }

  if (mode == gpioModeDisabled)
  {
    if (out)
    {
      GPIO->P[port].DOUTSET = 1 << pin;
    }
    else
    {
      GPIO->P[port].DOUTCLR = 1 << pin;
    }
  }
}

/***************************************************************************//**
 * @brief
 *   Configure GPIO interrupt.
 *
 * @details
 *   If reconfiguring a GPIO interrupt that is already enabled, it is generally
 *   recommended to disable it first, see GPIO_Disable().
 *
 *   The actual GPIO interrupt handler must be in place before enabling the
 *   interrupt.
 *
 *   Notice that any pending interrupt for the selected pin is cleared by this
 *   function.
 *
 * @note
 *   A certain pin number can only be associated with one port. Ie, if GPIO
 *   interrupt 1 is assigned to port A/pin 1, then it is not possibly to use
 *   pin 1 from any other ports for interrupts. Please refer to the reference
 *   manual.
 *
 * @param[in] port
 *   The port to associate with @p pin.
 *
 * @param[in] pin
 *   The GPIO interrupt number (= port pin).
 *
 * @param[in] risingEdge
 *   Set to true if interrupts shall be enabled on rising edge, otherwise false.
 *
 * @param[in] fallingEdge
 *   Set to true if interrupts shall be enabled on falling edge, otherwise false.
 *
 * @param[in] enable
 *   Set to true if interrupt shall be enabled after configuration completed,
 *   false to leave disabled. See GPIO_IntDisable() and GPIO_IntEnable().
 ******************************************************************************/
void GPIO_IntConfig(GPIO_Port_TypeDef port,
                    unsigned int pin,
                    bool risingEdge,
                    bool fallingEdge,
                    bool enable)
{
  uint32_t tmp;

  EFM_ASSERT(GPIO_PORT_VALID(port) && GPIO_PIN_VALID(pin));

  /* There are two registers controlling the interrupt configuration:
   * The EXTIPSELL register controls pins 0-7 and EXTIPSELH controls
   * pins 8-15. */
  if (pin < 8)
  {
    GPIO->EXTIPSELL = (GPIO->EXTIPSELL & ~(0xF << (4 * pin))) |
                      (port << (4 * pin));
  }
  else
  {
    tmp             = pin - 8;
    GPIO->EXTIPSELH = (GPIO->EXTIPSELH & ~(0xF << (4 * tmp))) |
                      (port << (4 * tmp));
  }

  /* Enable/disable rising edge */
  BITBAND_Peripheral(&(GPIO->EXTIRISE), pin, (unsigned int)risingEdge);

  /* Enable/disable falling edge */
  BITBAND_Peripheral(&(GPIO->EXTIFALL), pin, (unsigned int)fallingEdge);

  /* Clear any pending interrupt */
  GPIO->IFC = 1 << pin;

  /* Finally enable/disable interrupt */
  BITBAND_Peripheral(&(GPIO->IEN), pin, (unsigned int)enable);
}

/***************************************************************************//**
 * @brief
 *   Toggle a single pin in GPIO port data out register.
 *
 * @note
 *   In order for the setting to take effect on the output pad, the pin must
 *   have been configured properly. If not, it will take effect whenever the
 *   pin has been properly configured.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] pins
 *   Bitmask with pins to toggle.
 ******************************************************************************/
void GPIO_PortOutToggle(GPIO_Port_TypeDef port, uint32_t pins)
{
  EFM_ASSERT(GPIO_PORT_VALID(port));

  GPIO->P[port].DOUTTGL = pins & _GPIO_P_DOUTTGL_DOUTTGL_MASK;
}

/***************************************************************************//**
 * @brief
 *   Set GPIO port data out register.
 *
 * @note
 *   In order for the setting to take effect on the respective output pads, the
 *   pins must have been configured properly. If not, it will take effect
 *   whenever the pin has been properly configured.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] val
 *   Value to write to port data out register.
 *
 * @param[in] mask
 *   Mask indicating which bits to modify.
 ******************************************************************************/
void GPIO_PortOutSetVal(GPIO_Port_TypeDef port, uint32_t val, uint32_t mask)
{
  EFM_ASSERT(GPIO_PORT_VALID(port));

  GPIO->P[port].DOUT = (GPIO->P[port].DOUT & ~mask) | (val & mask);
}

/***************************************************************************//**
 * @brief
 *   Set bits GPIO data out register to 1.
 *
 * @note
 *   In order for the setting to take effect on the respective output pads, the
 *   pins must have been configured properly. If not, it will take effect
 *   whenever the pin has been properly configured.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] pins
 *   Bit mask for bits to set to 1 in DOUT register.
 ******************************************************************************/
void GPIO_PortOutSet(GPIO_Port_TypeDef port, uint32_t pins)
{
  EFM_ASSERT(GPIO_PORT_VALID(port));

  GPIO->P[port].DOUTSET = pins & _GPIO_P_DOUTSET_DOUTSET_MASK;
}

/***************************************************************************//**
 * @brief
 *   Get current setting for a GPIO port data out register.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @return
 *   The data out setting for the requested port.
 ******************************************************************************/
uint32_t GPIO_PortOutGet(GPIO_Port_TypeDef port)
{
  EFM_ASSERT(GPIO_PORT_VALID(port));

  return(GPIO->P[port].DOUT & _GPIO_P_DOUT_DOUT_MASK);
}

/***************************************************************************//**
 * @brief
 *   Set bits in DOUT register for a port to 0.
 *
 * @note
 *   In order for the setting to take effect on the output pad, the pin must
 *   have been configured properly. If not, it will take effect whenever the
 *   pin has been properly configured.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] pins
 *   Bit mask for bits to clear in DOUT register.
 ******************************************************************************/
void GPIO_PortOutClear(GPIO_Port_TypeDef port, uint32_t pins)
{
  EFM_ASSERT(GPIO_PORT_VALID(port));

  GPIO->P[port].DOUTCLR = pins & _GPIO_P_DOUTCLR_DOUTCLR_MASK;
}

/***************************************************************************//**
 * @brief
 *   Read the pad values for GPIO port.
 *
 * @param[in] port
 *   The GPIO port to access.
 ******************************************************************************/
uint32_t GPIO_PortInGet(GPIO_Port_TypeDef port)
{
  EFM_ASSERT(GPIO_PORT_VALID(port));

  return(GPIO->P[port].DIN & _GPIO_P_DIN_DIN_MASK);
}

/***************************************************************************//**
 * @brief
 *   Toggle a single pin in GPIO port data out register.
 *
 * @note
 *   In order for the setting to take effect on the output pad, the pin must
 *   have been configured properly. If not, it will take effect whenever the
 *   pin has been properly configured.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] pin
 *   The pin to toggle.
 ******************************************************************************/
void GPIO_PinOutToggle(GPIO_Port_TypeDef port, unsigned int pin)
{
  EFM_ASSERT(GPIO_PORT_VALID(port) && GPIO_PIN_VALID(pin));

  GPIO->P[port].DOUTTGL = 1 << pin;
}

/***************************************************************************//**
 * @brief
 *   Get current setting for a pin in a GPIO port data out register.
 *
 * @param[in] port
 *   The GPIO port to access.
 *
 * @param[in] pin
 *   The pin to get setting for.
 *
 * @return
 *   The DOUT setting for the requested pin, 0 or 1.
 ******************************************************************************/
unsigned int GPIO_PinOutGet(GPIO_Port_TypeDef port, unsigned int pin)
{
  EFM_ASSERT(GPIO_PORT_VALID(port) && GPIO_PIN_VALID(pin));

  return((unsigned int)((GPIO->P[port].DOUT >> pin) & 0x1));
}