C++ GPIOPinTypeGPIOOutput函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中GPIOPinTypeGPIOOutput函数的典型用法代码示例。如果您正苦于以下问题：C++ GPIOPinTypeGPIOOutput函数的具体用法？C++ GPIOPinTypeGPIOOutput怎么用？C++ GPIOPinTypeGPIOOutput使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了GPIOPinTypeGPIOOutput函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: main

int main()
{
	SysCtlClockSet(SYSCTL_SYSDIV_2_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);

	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_SSI2);
	GPIOPinConfigure(GPIO_PB4_SSI2CLK);
	GPIOPinConfigure(GPIO_PB7_SSI2TX);
	GPIOPinTypeSSI(GPIO_PORTB_BASE,GPIO_PIN_4|GPIO_PIN_7);
	SSIConfigSetExpClk(SSI2_BASE,SysCtlClockGet(),SSI_FRF_MOTO_MODE_0,SSI_MODE_MASTER,2000000,8);
	SSIEnable(SSI2_BASE);

	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
	GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_2|GPIO_PIN_3);
	GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_2,0);
	GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_3,0);

	GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_6);
	GPIOPinWrite(GPIO_PORTB_BASE,GPIO_PIN_6,0);

	while(1)
	{
		SSIDataPut(SSI2_BASE,0xAA);
		latch();
		SysCtlDelay(SysCtlClockGet()/10);

		SSIDataPut(SSI2_BASE,0x55);
		latch();
		SysCtlDelay(SysCtlClockGet()/10);
	}
}

开发者ID:anshuman94，项目名称:StarShipXP，代码行数:31，代码来源:main.c

示例2: EK_TM4C123GXL_initGPIO

/*
 *  ======== EK_TM4C123GXL_initGPIO ========
 */
void EK_TM4C123GXL_initGPIO(void)
{
    /* Setup the LED GPIO pins used */
    GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1); /* EK_TM4C123GXL_LED_RED */
    GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2); /* EK_TM4C123GXL_LED_GREEN */
    GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3); /* EK_TM4C123GXL_LED_BLUE */

    /* Setup the button GPIO pins used */
    GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_4);  /* EK_TM4C123GXL_GPIO_SW1 */
    GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_STRENGTH_4MA, GPIO_PIN_TYPE_STD_WPU);

    /* PF0 requires unlocking before configuration */
    HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
    HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= GPIO_PIN_0;
    GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_0);  /* EK_TM4C123GXL_GPIO_SW2 */
    GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_0, GPIO_STRENGTH_4MA, GPIO_PIN_TYPE_STD_WPU);
    HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_M;

    /* Once GPIO_init is called, GPIO_config cannot be changed */
    GPIO_init();

    GPIO_write(EK_TM4C123GXL_LED_RED, EK_TM4C123GXL_LED_OFF);
    GPIO_write(EK_TM4C123GXL_LED_GREEN, EK_TM4C123GXL_LED_OFF);
    GPIO_write(EK_TM4C123GXL_LED_BLUE, EK_TM4C123GXL_LED_OFF);
}

开发者ID:erniep，项目名称:Potatoes，代码行数:28，代码来源:EK_TM4C123GXL.c

示例3: FPUEnable

void Board::init() // initialize the board specifics
{
	//
	// Enable lazy stacking for interrupt handlers.  This allows floating-point
	// instructions to be used within interrupt handlers, but at the expense of
	// extra stack usage.
	//
	FPUEnable();
	FPULazyStackingEnable();
	//
	// Set the clocking to run from the PLL at 50MHz
	//
	ROM_SysCtlClockSet(
	SYSCTL_SYSDIV_1 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
	IntMasterEnable(); // Enable interrupts to the processor.
	// Set up the period for the SysTick timer for 1 mS.
	SysTickPeriodSet(SysCtlClockGet() / 1000);
	SysTickIntEnable(); // Enable the SysTick Interrupt.
	SysTickEnable(); // Enable SysTick.
	/*	//
	 // Enable lazy stacking for interrupt handlers.  This allows floating-point
	 // instructions to be used within interrupt handlers, but at the expense of
	 // extra stack usage.
	 FPUEnable();
	 FPULazyStackingEnable();
	 SysCtlClockSet(
	 SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN
	 | SYSCTL_XTAL_16MHZ); // Set the clocking to run directly from the crystal.
	 IntMasterEnable(); // Enable interrupts to the processor.*/

	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF); // Enable the GPIO port that is used for the on-board LED.
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2); // Enable the GPIO pins for the LED (PF2).
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3);

	/*	SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0); // Enable the peripherals used by this example.
	 SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
	 IntMasterEnable(); // Enable processor interrupts.
	 // Set up the period for the SysTick timer for 1 mS.
	 SysTickPeriodSet(SysCtlClockGet() / 1000);
	 SysTickIntEnable(); // Enable the SysTick Interrupt.
	 SysTickEnable(); // Enable SysTick.

	 GPIOPinConfigure(GPIO_PA0_U0RX); // Set GPIO A0 and A1 as UART pins.
	 GPIOPinConfigure(GPIO_PA1_U0TX);
	 GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);

	 UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,
	 (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE)); // Configure the UART for 115,200, 8-N-1 operation.
	 IntEnable(INT_UART0);
	 UARTFIFODisable(UART0_BASE);
	 //	UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX1_8, UART_FIFO_RX1_8);
	 UARTFlowControlSet(UART0_BASE, UART_FLOWCONTROL_NONE);
	 UARTIntDisable(UART0_BASE, UART_INT_RT);
	 UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_TX); // Enable the UART interrupt.*/
	Board::setLedOn(Board::LED_GREEN, false);
	Board::setLedOn(Board::LED_RED, false);
	Board::setLedOn(Board::LED_BLUE, false);
	AdcInit();
}

开发者ID:vortex314，项目名称:projects，代码行数:60，代码来源:Board.cpp

示例4: exec3

void exec3(void)
{
	//RGBInit(TRUE);
    // Enable the GPIO Port and Timer for each LED
    SysCtlPeripheralEnable(RED_GPIO_PERIPH);
    SysCtlPeripheralEnable(GREEN_GPIO_PERIPH);
    SysCtlPeripheralEnable(BLUE_GPIO_PERIPH);

    // Reconfigure each LED's GPIO pad for timer control
    GPIOPadConfigSet(GREEN_GPIO_BASE, GREEN_GPIO_PIN, GPIO_STRENGTH_8MA_SC, GPIO_PIN_TYPE_STD);
    GPIOPinTypeGPIOOutput(GREEN_GPIO_BASE, GREEN_GPIO_PIN);

    GPIOPadConfigSet(BLUE_GPIO_BASE, BLUE_GPIO_PIN, GPIO_STRENGTH_8MA_SC, GPIO_PIN_TYPE_STD);
    GPIOPinTypeGPIOOutput(BLUE_GPIO_BASE, BLUE_GPIO_PIN);

    GPIOPadConfigSet(RED_GPIO_BASE, RED_GPIO_PIN, GPIO_STRENGTH_8MA_SC, GPIO_PIN_TYPE_STD);
    GPIOPinTypeGPIOOutput(RED_GPIO_BASE, RED_GPIO_PIN);

	while(1)
	{
		GPIOPinWrite(BLUE_GPIO_BASE, BLUE_GPIO_PIN, BLUE_GPIO_PIN);
		DelayTask(100);
		GPIOPinWrite(BLUE_GPIO_BASE, BLUE_GPIO_PIN, 0);
		DelayTask(100);
	}
}

开发者ID:monkaco，项目名称:BRTOS，代码行数:26，代码来源:tarefas.c

示例5: MAC_RfFrontendSetup

/**************************************************************************************************
 * @fn          MAC_RfFrontendSetup
 *
 * @brief       Setup RF frontend.
 *
 * @param       none
 *
 * @return      none
 **************************************************************************************************
 */
void MAC_RfFrontendSetup(void)
{
  GPIOPinTypeGPIOOutput(GPIO_C_BASE, GPIO_PIN_3);
  GPIOPinTypeGPIOOutput(GPIO_C_BASE, GPIO_PIN_2);

  /* CC2591 HGM pin control configuration.
   *   PD2 -> HGM
   */
  HAL_PA_LNA_RX_HGM();

  /* Raises the CCA threshold to about -70 dBm input level.
   */
  CCACTRL0 = CCA_THR_HGM;

  /* Select power register value table and RSSI adjustment value table */
  #if (defined MAC_RUNTIME_CC2591 && defined MAC_RUNTIME_CC2590)
  /* Select power register value table and RSSI adjustment value table.
   * Note that this file selected CC2591. The file has to be modified
   * if the target board has CC2590 instead.
   */
  MAC_SetRadioRegTable(MAC_CC2591_TX_PWR_TABLE_IDX, MAC_CC2591_HGM_RSSI_ADJ_IDX);

  #elif defined (MAC_RUNTIME_CC2591) || defined (MAC_RUNTIME_CC2590)
  /* Select power register value table and RSSI adjustment value table */
  MAC_SetRadioRegTable(MAC_CC259X_TX_PWR_TABLE_IDX, MAC_CC259X_HGM_RSSI_ADJ_IDX);

  #elif defined (HAL_PA_LNA) || defined (HAL_PA_LNA_CC2590)
  /* No need to do anything here because by default macRadioDefsRefTableId = 0 hence,
   * automatically setup for HGM. However if you want LGM modify this file and call
   * MAC_SetRadioRegTable(0,  MAC_PA_LNA_LGM_RSSI_ADJ_IDX);
   */
  #endif
}

开发者ID:chessami92，项目名称:ceen4360-cc2538-code，代码行数:43，代码来源:mac_rffrontend.c

示例6: STEP_Init

void STEP_Init(struct STEP_Motor* stMotorHandle)
{
	// Enable Port for Motor Control
	SysCtlPeripheralEnable(stMotorHandle->ui32STEP_BaseAddress);

	// Enable Port for Motor Control "Enable"
	SysCtlPeripheralEnable(STEP_ENABLE_PERIPH);

	// Disable NMI for PD7 if it will be used
	if( (stMotorHandle->ui32STEP_BaseAddress == SYSCTL_PERIPH_GPIOD) && ( (stMotorHandle->ui32STEP_DirPin == GPIO_PIN_7) || (stMotorHandle->ui32STEP_MovePin == GPIO_PIN_7) ) )
	{
		HWREG(GPIO_PORTD_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
		HWREG(GPIO_PORTD_BASE + GPIO_O_CR) |= 0x80;
		HWREG(GPIO_PORTD_BASE + GPIO_O_LOCK) = 0;
	}

	// Init Stepper Motor Pins - Direction
	GPIOPinTypeGPIOOutput(stMotorHandle->ui32STEP_Port, stMotorHandle->ui32STEP_DirPin);

	// Init Stepper Motor Pins - Movement (toggle for step)
	GPIOPinTypeGPIOOutput(stMotorHandle->ui32STEP_Port, stMotorHandle->ui32STEP_MovePin);

	// Init Stepper Motor Pins - Enable
	GPIOPinTypeGPIOOutput(STEP_ENABLE_PORT, STEP_ENABLE_PIN);
}

开发者ID:Roicker，项目名称:Control_Board，代码行数:25，代码来源:STEP.c

示例7: EK_TM4C123GXL_initGPIO

/*
 *  ======== EK_TM4C123GXL_initGPIO ========
 */
void EK_TM4C123GXL_initGPIO(void) {

	GPIOPadConfigSet(GPIO_PORTA_BASE,GPIO_PIN_2,GPIO_STRENGTH_8MA,GPIO_PIN_TYPE_STD_WPD);
	GPIOPadConfigSet(GPIO_PORTA_BASE,GPIO_PIN_3,GPIO_STRENGTH_8MA,GPIO_PIN_TYPE_STD_WPD);

	GPIOPinTypeGPIOInput(GPIO_PORTA_BASE, GPIO_PIN_2); /* ENC_A */
	GPIOPinTypeGPIOInput(GPIO_PORTA_BASE, GPIO_PIN_3); /* ENC_B */
	GPIOIntTypeSet(GPIO_PORTA_BASE,GPIO_PIN_2,GPIO_INT_BOTH_EDGES);

	GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_2); /* Load cell clock*/
	GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_3); /* Load cell data*/


	GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_0); /* Test Button 1*/
	GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_1); /* Test Button 2*/
	GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_2); /* Test Button 3*/

	/* Setup the LED GPIO pins used */
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1); /* Test led 2 */
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2); /* Test led 3 */


	/* PF0 requires unlocking before configuration */
	HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
	HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= GPIO_PIN_0;
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_0); /* Test led 1 */

	HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_M;

	/* Once GPIO_init is called, GPIO_config cannot be changed */
	GPIO_init();


}

开发者ID:plurryinc，项目名称:embeded-test，代码行数:37，代码来源:EK_TM4C123GXL.c

示例8: EK_TM4C123GXL_initWiFi

/*
 *  ======== EK_TM4C123GXL_initWiFi ========
 */
void EK_TM4C123GXL_initWiFi(void)
{
    /* Configure SSI2 */
    SysCtlPeripheralEnable(SYSCTL_PERIPH_SSI2);
    GPIOPinConfigure(GPIO_PB4_SSI2CLK);
    GPIOPinConfigure(GPIO_PB6_SSI2RX);
    GPIOPinConfigure(GPIO_PB7_SSI2TX);
    GPIOPinTypeSSI(GPIO_PORTB_BASE, GPIO_PIN_4 | GPIO_PIN_6 | GPIO_PIN_7);

    /* Configure IRQ pin */
    GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_2);
    GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);

    /* Configure EN pin */
    GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_5);
    GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_5, 0);

    /* Configure CS pin */
    GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE, GPIO_PIN_0);
    GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_0, 0);

    /* Call necessary SPI init functions */
    SPI_init();
    EK_TM4C123GXL_initDMA();

    /* Initialize WiFi driver */
    WiFi_init();
}

开发者ID:Hoxford，项目名称:tyler-woogduh，代码行数:31，代码来源:EK_TM4C123GXL.c

示例9: main

int main() {

  //Enable Peripherals
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); 
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC); 
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);  
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);  
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);  

  
  //Start specific Pin Ports
  GPIOPinTypeGPIOOutput(port_A, GPIO_PIN_5 |GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4); 
  GPIOPinTypeGPIOOutput(port_C, GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_6 | GPIO_PIN_7); 
  GPIOPinTypeGPIOOutput(port_D,GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_6 | GPIO_PIN_5); 
  GPIOPinTypeGPIOOutput(port_E, GPIO_PIN_0); 
  GPIOPinTypeGPIOOutput(port_F, GPIO_PIN_4); 
  
  //Input Pins
  GPIOPinTypeGPIOInput(port_F, GPIO_PIN_2 | GPIO_PIN_3);
  
  //Initialize the display
  initializeDisplay();
  
  //Write phrases
  write_phrases();

}

开发者ID:phuongtg，项目名称:micro2-1，代码行数:27，代码来源:new.c

示例10: setup

void setup(void){
	//Enable the driver layer
	SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
	                       SYSCTL_XTAL_16MHZ);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);

	//Pinout connections:
	//
	GPIOPinTypeGPIOInput(GPIO_PORTA_BASE,GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);
	GPIOPadConfigSet(GPIO_PORTA_BASE, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7, GPIO_STRENGTH_2MA,
	                     GPIO_PIN_TYPE_STD_WPU);
	GPIOIntTypeSet(GPIO_PORTA_BASE, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7,GPIO_FALLING_EDGE);
	GPIOPinTypeGPIOInput(GPIO_PORTB_BASE,GPIO_PIN_4);
	GPIOPadConfigSet(GPIO_PORTB_BASE, GPIO_PIN_4, GPIO_STRENGTH_2MA,
		                     GPIO_PIN_TYPE_STD_WPU);
	GPIOIntTypeSet(GPIO_PORTB_BASE,GPIO_PIN_4,GPIO_FALLING_EDGE);
	GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE,GPIO_PIN_5|GPIO_PIN_4);
	GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE,GPIO_PIN_1|GPIO_PIN_0);
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE,GPIO_PIN_2|GPIO_PIN_1|GPIO_PIN_3);

	GPIOPinIntEnable(GPIO_PORTA_BASE, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);
	GPIOPinIntEnable(GPIO_PORTB_BASE,GPIO_PIN_4);
	IntMasterEnable();
	IntEnable(INT_GPIOA);
	IntEnable(INT_GPIOB);
	GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, 0);
	GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, 0);
	GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_4, 0);
	GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_5, 0);

}

开发者ID:dmanchon，项目名称:stellaris-launchpad-keypad-4x4，代码行数:35，代码来源:usb_dev_keyboard.c

示例11: main

int main(void)
{
  My_Init();
  Init_Timer();
  Init_I2C();
  Init_Sensors();
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
  GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
    /////////////////////////////////
  SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
  		SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
  		GPIOPinConfigure(GPIO_PA0_U0RX);
  		GPIOPinConfigure(GPIO_PA1_U0TX);
  		GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
  		SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF); //enable GPIO port for LED
  		GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2); //enable pin for LED PF2
  		UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,
  				(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
  		IntMasterEnable(); //enable processor interrupts
  		IntEnable(INT_UART0); //enable the UART interrupt
  		UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT); //only enable RX and TX interrupts
/////////////////////////////////
  Kalman_Sim_initialize();

  while(1)
  {
    Read_Accelerometer();
    Calculate_Acc();
    Read_Compass();
    Compass_Heading();
    Calculate_Compass();
    Read_Gyro();
    Calculate_Gyro();

    fgyro[0]    = sen_data.gyro_x;
    fgyro[1]	= sen_data.gyro_y;
    fgyro[2]	= sen_data.gyro_z;

    facc[0]     = sen_data.accel_x;
    facc[1]	= sen_data.accel_y;
    facc[2]	= sen_data.accel_z;

    fmag[0]     = sen_data.magnetom_x;
    fmag[1]	= sen_data.magnetom_y;
    fmag[2]	= sen_data.magnetom_z;


    Kalman_Sim_step();

    data[0]=Out1[0];
    data[1]=Out1[1];
    data[2]=Out1[2];



      Timer_CyRun();

  }
}

开发者ID:nemo1992，项目名称:9DOF，代码行数:59，代码来源:main.c

示例12: antenna_init

/**
 * Configures the antenna using a RF switch
 * INT is the internal antenna (chip) configured through ANT1_SEL (V1)
 * EXT is the external antenna (connector) configured through ANT2_SEL (V2)
 */
void antenna_init(void) {
    // Configure the ANT1 and ANT2 GPIO as output
    GPIOPinTypeGPIOOutput(BSP_RADIO_BASE, BSP_RADIO_INT);
    GPIOPinTypeGPIOOutput(BSP_RADIO_BASE, BSP_RADIO_EXT);

    // By default the chip antenna is selected as the default
    GPIOPinWrite(BSP_RADIO_BASE, BSP_RADIO_INT, BSP_RADIO_INT);
    GPIOPinWrite(BSP_RADIO_BASE, BSP_RADIO_EXT, ~BSP_RADIO_EXT);
}

开发者ID:barriquello，项目名称:iotstack，代码行数:14，代码来源:board.c

示例13: control_init

void control_init() {
  //// laser control
  // Setup Timer0 for a 488.28125Hz "phase correct PWM" wave (assuming a 16Mhz clock)
  // Timer0 can pwm either PD5 (OC0B) or PD6 (OC0A), we use PD6
  // TCCR0A and TCCR0B are the registers to setup Timer0
  // see chapter "8-bit Timer/Counter0 with PWM" in Atmga328 specs
  // OCR0A sets the duty cycle 0-255 corresponding to 0-100%
  // also see: http://arduino.cc/en/Tutorial/SecretsOfArduinoPWM

	GPIOPinTypeGPIOOutput(LASER_EN_PORT, LASER_EN_MASK);
	GPIOPinWrite(LASER_EN_PORT, LASER_EN_MASK, LASER_EN_INVERT);

	// Configure timer
	SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
	TimerConfigure(LASER_TIMER, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM|TIMER_CFG_B_ONE_SHOT);
	TimerControlLevel(LASER_TIMER, TIMER_A, 1);

	// PPI = PWMfreq/(feedrate/MM_PER_INCH/60)

	// Set PPI Pulse timer
	ppi_cycles = SysCtlClockGet() / 1000 * CONFIG_LASER_PPI_PULSE_MS;
	ppi_divider = ppi_cycles >> 16;
	ppi_cycles /= (ppi_divider + 1);
	TimerPrescaleSet(LASER_TIMER, TIMER_B, ppi_divider);
	TimerLoadSet(LASER_TIMER, TIMER_B, ppi_cycles);

	// Setup ISR
	TimerIntRegister(LASER_TIMER, TIMER_B, laser_isr);
	TimerIntEnable(LASER_TIMER, TIMER_TIMB_TIMEOUT);
    IntPrioritySet(INT_TIMER0B, CONFIG_LASER_PRIORITY);

	// Set PWM refresh rate
	laser_cycles = SysCtlClockGet() / CONFIG_LASER_PWM_FREQ; /*Hz*/
	laser_divider = laser_cycles >> 16;
	laser_cycles /= (laser_divider + 1);

	// Setup Laser PWM Timer
	TimerPrescaleSet(LASER_TIMER, TIMER_A, laser_divider);
	TimerLoadSet(LASER_TIMER, TIMER_A, laser_cycles);
	TimerPrescaleMatchSet(LASER_TIMER, TIMER_A, laser_divider);
	laser_intensity = 0;

	// Set default value
	control_laser_intensity(0);
	control_laser(0, 0);

	TimerEnable(LASER_TIMER, TIMER_A);

	// ToDo: Map the timer ccp pin sensibly
	GPIOPinConfigure(GPIO_PB6_T0CCP0);
	GPIOPinTypeTimer(LASER_PORT, (1 << LASER_BIT));

	//// air and aux assist control
	GPIOPinTypeGPIOOutput(ASSIST_PORT, ASSIST_MASK);
	control_air_assist(false);
	control_aux1_assist(false);
}

开发者ID:DevJohan，项目名称:LasaurGrbl，代码行数:57，代码来源:sense_control.c

示例14: lcd_port_config

//Function to configure LCD port
void lcd_port_config (void)
{

	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);	// data pins

	GPIOPinTypeGPIOOutput(GPIO_PORTC_BASE, (GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_6));	// PC4 RS; PC5 RW; PC6 EN
	GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, (GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7));	// 8 bit interfacing
}

开发者ID:sauravshandilya，项目名称:EE712-Embedded-System-Design，代码行数:10，代码来源:lcd.c

示例15: main

int main(void)
{

	SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); // Enable the GPIO A ports
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE); // Enable the GPIO E ports
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);

	GPIOPinConfigure(GPIO_PB6_M0PWM0);
	GPIOPinTypePWM(GPIO_PORTB_BASE, GPIO_PIN_6);

	GPIOPinConfigure(GPIO_PB7_M0PWM1);
	GPIOPinTypePWM(GPIO_PORTB_BASE, GPIO_PIN_7);

	PWMGenConfigure(PWM0_BASE, PWM_GEN_0, PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
	PWMGenPeriodSet(PWM0_BASE, PWM_GEN_0, 6400000);
	PWMPulseWidthSet(PWM0_BASE, PWM_OUT_0, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_0) / 1.25);
	PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, true);
	PWMGenEnable(PWM0_BASE, PWM_GEN_0);

	PWMGenConfigure(PWM0_BASE, PWM_GEN_1, PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
	PWMGenPeriodSet(PWM0_BASE, PWM_GEN_1, 6400000);
	PWMPulseWidthSet(PWM0_BASE, PWM_OUT_1, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_1) / 1.25);
	PWMOutputState(PWM0_BASE, PWM_OUT_1_BIT, true);
	PWMGenEnable(PWM0_BASE, PWM_GEN_1);


	GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_6|GPIO_PIN_7); // Set pin 7 as the output port
	GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE, GPIO_PIN_1|GPIO_PIN_2);
	GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_5);


	GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,64); // Give '1' to pin 7
	GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,4);
	while(1)
	{
		GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,64); // Give '1' to pin 7
		GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,4);
		SysCtlDelay(4000000*10);
		GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,0); // Give '1' to pin 7
	    GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,0);
	    GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,32);
	    SysCtlDelay(400000);
	    GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,0);
		GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,128); // Give '1' to pin 7
		GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,2);
		SysCtlDelay(4000000*10);
		GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,0); // Give '1' to pin 7
		GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,0);
		GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,32);
		SysCtlDelay(400000);
		GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,0);

	}
}

开发者ID:eYSIP-2016，项目名称:Robot_State_Collector，代码行数:56，代码来源:Alternate+motor+and+buzzer.c

示例16: IoPortInit

void IoPortInit(void)
{
	//
	// Enable the GPIO block.
	//
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
	//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
	//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
	//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
	//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
	//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
     SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOJ);

	     // 要解锁只需要在配置GPIO前加入下面代码就可以了：

   // Unlock GPIO Commit GPIOAFSEL

   HWREG(GPIO_PORTB_BASE + GPIO_O_LOCK) = 0x4C4F434B;
  

   // Manually Write CR Register for PB7

   HWREG(GPIO_PORTB_BASE + GPIO_O_CR) |= (1 << 7);

 //  HWREG(GPIO_PORTB_BASE + GPIO_O_LOCK) = 0x1;

	//
	// Set GPIO D7 as an output.  This drives an LED on the board that will
	// toggle when a watchdog interrupt is processed.
	//
	GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, PIN_AD7705_RST|PIN_AD7705_CS|PIN_AD7705_DIN|PIN_AD7705_SCLK);//
	GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, PIN_AD7367_ADDR|PIN_AD7367_CNVST|PIN_AD7367_CS|PIN_AD7367_SCLK);
	//GPIOPinTypeGPIOOutput(GPIO_PORTD_BASE, PIN_200X|PIN_2KX | PIN_20KX |PIN_3X);
	GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE, PIN_JUN|PIN_JUX|PIN_JRTG|PIN_JUNX);
	//GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, PIN_20N  | PIN_200N |  PIN_2KN );
	//GPIOPinTypeGPIOOutput(GPIO_PORTG_BASE, PIN_20KN |PIN_NX  | PIN_filterPASS|PIN_3N |PIN_ADC_ADDR|PIN_ADC_RANGE0);
    //GPIOPinTypeGPIOOutput(GPIO_PORTH_BASE, PIN_CE6963|PIN_CD6963|PIN_RD6963|PIN_WR6963);
    GPIOPinTypeGPIOOutput(GPIO_PORTJ_BASE, PIN_JR);

	GPIOPinTypeGPIOInput(GPIO_PORTA_BASE, PIN_AD7705_DRDY|PIN_AD7705_DOUT);//
	GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, PIN_AD7367_DOUTB|PIN_AD7367_BUSY);
//    GPIOPinTypeGPIOInput(GPIO_PORTC_BASE,PIN_ADC_BUSY);
//	GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, PIN_KEY1 | PIN_KEY2 | PIN_KEY3 | PIN_KEY4);
//    GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, PIN_keyback| PIN_keydown|PIN_keyprint|PIN_keyset|PIN_keystart|PIN_keyup);
//	GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, PIN_ISP2);
//	GPIOPinTypeGPIOInput(GPIO_PORTG_BASE, PIN_ADC_DOUTA );
//	GPIOPinTypeGPIOInput(GPIO_PORTH_BASE, );

//	GpioIntInit();

//	Led1Write(0);
//	Led2Write(0);
	
}

开发者ID:qiurenguo2014，项目名称:youjiesun_dg，代码行数:56，代码来源:Untitled_AH9837.c

示例17: initLEDs

void initLEDs()
{
	  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPION);
		SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
	  GPIOPinTypeGPIOOutput(GPIO_PORTN_BASE, GPIO_PIN_0|GPIO_PIN_1);
		GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_0|GPIO_PIN_4);
	  GPIOPinWrite(GPIO_PORTN_BASE,GPIO_PIN_0, PIN_LOW);
	  GPIOPinWrite(GPIO_PORTN_BASE,GPIO_PIN_1, PIN_LOW);
		GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_0, PIN_LOW);
	  GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_4, PIN_LOW);
}

开发者ID:WiFiProject，项目名称:HTTP-Server-Based-on-Embedded-System，代码行数:11，代码来源:board.c

示例18: ConfigDRV_Enable

void ConfigDRV_Enable()
{
	SysCtlPeripheralEnable(DRV_ENABLE_LEFT_CHN_PERIPHERAL);
	SysCtlPeripheralEnable(DRV_ENABLE_RIGHT_CHN_PERIPHERAL);
	GPIOPinTypeGPIOOutput(DRV_ENABLE_LEFT_CHN_PORT, DRV_ENABLE_LEFT_CHN_PIN);
	GPIOPinTypeGPIOOutput(DRV_ENABLE_RIGHT_CHN_PORT, DRV_ENABLE_RIGHT_CHN_PIN);
//	GPIOPinTypeGPIOOutputOD(DRV_ENABLE_RIGHT_CHN_PORT,DRV_ENABLE_LEFT_CHN_PIN  | DRV_ENABLE_RIGHT_CHN_PIN);
	//	Turn off DRV when start
	GPIOPinWrite(DRV_ENABLE_LEFT_CHN_PORT, DRV_ENABLE_LEFT_CHN_PIN, 0);
	GPIOPinWrite(DRV_ENABLE_RIGHT_CHN_PORT, DRV_ENABLE_RIGHT_CHN_PIN, 0);
}

开发者ID:vonamhai，项目名称:self-balancing-robot，代码行数:11，代码来源:PWM.c

示例19: led_init

void led_init(){

	/* PF0 requires unlocking before configuration */
	HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
	HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= GPIO_PIN_0;
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_0);
	HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_M;

	GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_7);
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
}

开发者ID:AntMaan，项目名称:Micromouse，代码行数:11，代码来源:led.c

示例20: MP3_pin_init

//***********************************************//
//MP3_pin_init 
//Prototype: void MP3_pin_init(void)
//Description: initial pins for communicate with vs1011e.
//Returns: None.
//***********************************************//
void MP3_pin_init()
{
	GPIOPinTypeGPIOOutput(MP3_CS);              // Configure MP3_CS as output
	deselect_MP3();							              // Deselect MP3_CS
	GPIOPinTypeGPIOOutput(MP3_RST);               // Configure MP3_RST as output
	GPIOPinWrite(MP3_RST,MP3_RST_PIN);               // Set MP3_RST pin
	
	GPIOPinTypeGPIOOutput(BSYNC);               // Configure BSYNC as output
	clear_BSYNC();		
	GPIOPinTypeGPIOInput(DREQPIN);                  // Configure DREQ as input
	GPIOPadConfigSet(DREQPIN, GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD_WPU);
}

开发者ID:minhhn2910，项目名称:MPlayer，代码行数:18，代码来源:mp3driver.c

注：本文中的GPIOPinTypeGPIOOutput函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ GPIOPinTypeSSI函数代码示例发布时间：2022-05-30

C++ GPIOPinTypeGPIOInput函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19189|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9988|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8326|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8696|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8639|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9657|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8624|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7998|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8656|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7535|2022-11-06

客服电话

电子邮件

C++ GPIOPinTypeGPIOOutput函数代码示例

示例1: main

示例2: EK_TM4C123GXL_initGPIO

示例3: FPUEnable

示例4: exec3

示例5: MAC_RfFrontendSetup

示例6: STEP_Init

示例7: EK_TM4C123GXL_initGPIO

示例8: EK_TM4C123GXL_initWiFi

示例9: main

示例10: setup

示例11: main

示例12: antenna_init

示例13: control_init

示例14: lcd_port_config

示例15: main

示例16: IoPortInit

示例17: initLEDs

示例18: ConfigDRV_Enable

示例19: led_init

示例20: MP3_pin_init

请发表评论

全部评论

上一篇：

下一篇：

PacktPublishing/Python-Machine-Learning-

sussillo/hfopt-matlab: A parallel, cpu-b

鲁东大学一米网:Win7系统USB驱动器RAM的操

色的笔顺,说说色的笔画,诠释色的部首

emersion/go-ostatus: An OStatus library

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053