C++ GPIOPinIntEnable函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中GPIOPinIntEnable函数的典型用法代码示例。如果您正苦于以下问题：C++ GPIOPinIntEnable函数的具体用法？C++ GPIOPinIntEnable怎么用？C++ GPIOPinIntEnable使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了GPIOPinIntEnable函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: main

void main(void)
	{
	SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN | SYSCTL_XTAL_8MHZ);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);

	GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_1);
	GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3);

	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_0); /* led */

    GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_1, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
    GPIOPadConfigSet(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);

	GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, GPIO_RISING_EDGE);
	GPIOIntTypeSet(GPIO_PORTF_BASE, GPIO_PIN_1, GPIO_RISING_EDGE);

	GPIOPinIntEnable(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3);
	GPIOPinIntEnable(GPIO_PORTF_BASE, GPIO_PIN_1);

	IntMasterEnable();
    IntEnable(INT_GPIOE);
    IntEnable(INT_GPIOF);
    GPIOPinIntClear(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3);
    GPIOPinIntClear(GPIO_PORTF_BASE, GPIO_PIN_1);
    while(1)
    	{
    	}
	}

开发者ID:jeremiaslehmann，项目名称:IntGPIO，代码行数:29，代码来源:main.c

示例2: initYaw

// *****************************************************************************
void initYaw (void)
{
    // Register the handler for Port F into the vector table
    GPIOPortIntRegister (GPIO_PORTF_BASE, YawChangeIntHandler);

    // Enable and configure the port and pin used:  input on PF5: Pin 27 & PF7: Pin 29
    SysCtlPeripheralEnable (SYSCTL_PERIPH_GPIOF);
    GPIOPadConfigSet (GPIO_PORTF_BASE, GPIO_PIN_5 | GPIO_PIN_7, GPIO_STRENGTH_2MA,
       GPIO_PIN_TYPE_STD_WPU);

    // Set up the pin change interrupt (both edges)
    GPIOIntTypeSet (GPIO_PORTF_BASE, GPIO_PIN_5 | GPIO_PIN_7, GPIO_BOTH_EDGES);

    // Enable the pin change interrupt
    GPIOPinIntEnable (GPIO_PORTF_BASE, GPIO_PIN_5 | GPIO_PIN_7);
    IntEnable (INT_GPIOF);	// Note: INT_GPIOF defined in inc/hw_ints.h

    //Registering Port D into the vector Table (Refwewnce point)
    GPIOPortIntRegister (GPIO_PORTD_BASE, referencePosIntHandler);

    GPIOPadConfigSet (GPIO_PORTD_BASE, GPIO_PIN_0, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
	//
	// Set up the pin change interrupt (both edges)
    GPIOIntTypeSet (GPIO_PORTD_BASE, GPIO_PIN_0, GPIO_BOTH_EDGES);
    //
    // Enable the pin change interrupt for PD0
    GPIOPinIntEnable (GPIO_PORTD_BASE, GPIO_PIN_0);

}

开发者ID:Yamoahs，项目名称:ENCE361_Helicopter_project，代码行数:30，代码来源:milestone2_MotorControl(PID)3.c

示例3: setup

void setup(void){
	//Enable the driver layer
	SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
	                       SYSCTL_XTAL_16MHZ);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);

	//Pinout connections:
	//
	GPIOPinTypeGPIOInput(GPIO_PORTA_BASE,GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);
	GPIOPadConfigSet(GPIO_PORTA_BASE, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7, GPIO_STRENGTH_2MA,
	                     GPIO_PIN_TYPE_STD_WPU);
	GPIOIntTypeSet(GPIO_PORTA_BASE, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7,GPIO_FALLING_EDGE);
	GPIOPinTypeGPIOInput(GPIO_PORTB_BASE,GPIO_PIN_4);
	GPIOPadConfigSet(GPIO_PORTB_BASE, GPIO_PIN_4, GPIO_STRENGTH_2MA,
		                     GPIO_PIN_TYPE_STD_WPU);
	GPIOIntTypeSet(GPIO_PORTB_BASE,GPIO_PIN_4,GPIO_FALLING_EDGE);
	GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE,GPIO_PIN_5|GPIO_PIN_4);
	GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE,GPIO_PIN_1|GPIO_PIN_0);
	GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE,GPIO_PIN_2|GPIO_PIN_1|GPIO_PIN_3);

	GPIOPinIntEnable(GPIO_PORTA_BASE, GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);
	GPIOPinIntEnable(GPIO_PORTB_BASE,GPIO_PIN_4);
	IntMasterEnable();
	IntEnable(INT_GPIOA);
	IntEnable(INT_GPIOB);
	GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, 0);
	GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, 0);
	GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_4, 0);
	GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_5, 0);

}

开发者ID:dmanchon，项目名称:stellaris-launchpad-keypad-4x4，代码行数:35，代码来源:usb_dev_keyboard.c

示例4: GPIO_SetInterruptTask

// *************** GPIO_SetInterruptTask *************** 					
void GPIO_SetInterruptTask( GPIO_PORT_T port, GPIO_PIN_T pins,
                            unsigned long int_type, unsigned long priority, 
							void (*task)( void ) )
{
	unsigned long port_base = GPIO_PortBase[port];

	// Set the interrupt task for the specified port and pins
	if     ( pins & 0x01 ) GPIO_PinISR[port][0] = task;
	else if( pins & 0x02 ) GPIO_PinISR[port][1] = task; 
	else if( pins & 0x04 ) GPIO_PinISR[port][2] = task;
	else if( pins & 0x08 ) GPIO_PinISR[port][3] = task;
	else if( pins & 0x10 ) GPIO_PinISR[port][4] = task;
	else if( pins & 0x20 ) GPIO_PinISR[port][5] = task;
	else if( pins & 0x40 ) GPIO_PinISR[port][6] = task;
	else if( pins & 0x80 ) GPIO_PinISR[port][7] = task;

	// Set the event type and priority, and clear the interrupt
	IntPrioritySet( GPIO_IntAssignment[port], priority );	 
	GPIOIntTypeSet( port_base, pins, int_type );
	GPIOPinIntClear( port_base, pins);

	// Enable interrupts
	IntEnable( GPIO_IntAssignment[port] );
 	GPIOPinIntEnable( port_base, pins );
}

开发者ID:yguo89，项目名称:CodeBrain，代码行数:26，代码来源:GPIO_Driver.c

示例5: Transceiver_ReceiveMessage

/******** Transceiver_receiveMessage *****************************************
// dequeue transceiver packet
// Input: 
//	  *pkt - pointer to received message 
// Output: status
// ------------------------------------------------------------------------*/
unsigned char Transceiver_ReceiveMessage ( TransceiverPacket *pkt )
{
	unsigned char rx[TRANSCEIVER_MAX_PAYLOAD];
	unsigned char index;
	unsigned char status = SUCCESS;

	GPIOPinIntDisable ( nrf24l01_IRQ_IOREGISTER, nrf24l01_IRQ_PIN );
	if ( pdPASS == xQueueReceive(Transceiver_RX_Queue, rx, (portTickType)0) )
	{
		pkt->srcID = rx[SOURCE_ID_INDEX];
		pkt->destID = rx[DEST_ID_INDEX];
		pkt->msgID = rx[MSG_ID_INDEX];
		pkt->dataSize = rx[DATA_SIZE_INDEX];
		for ( index = 0; index < pkt->dataSize; index++ )
		{
			pkt->data[index] = rx[index+PACKET_HEADER_SIZE];
		}
		Debug_NetworkTransceiver_PrintPacket(pkt);
	}
	else
	{
		// empty queue
		status = ERROR_QUEUE_EMPTY;
		Debug_Printf ("Transceiver_ReceiveMessage 0x%x\n", status);
		if ( EmptyQueueCallBack != NULL )
			xTaskCreate( Transceiver_EmptyQueueCallBack, ( signed portCHAR * ) "Transceiver_EmptyQueueCallBack", 
				 DEFAULT_STACK_SIZE, NULL, DEFAULT_PRIORITY, NULL );
	}

	GPIOPinIntEnable ( nrf24l01_IRQ_IOREGISTER, nrf24l01_IRQ_PIN );

	return status;
}

开发者ID:yguo89，项目名称:CodeBrain，代码行数:39，代码来源:Transceiver.c

示例6: ctl_buttons_isr_init

//ISR INIT
void ctl_buttons_isr_init(CTL_ISR_FN_t fn)
{
int en; int32u proba;
en=ctl_global_interrupts_set(0);
buttons_isr=fn;
SysCtlPeripheralEnable(PUSHBUTTON_PERIPH);
//UNLOCKOLNI KELL A PF0 REGISZTERT MERT NMI-RE VAN ALLITVA
HWREG(PUSHBUTTON_PORT + GPIO_O_LOCK) = GPIO_LOCK_KEY_DD;
HWREG(PUSHBUTTON_PORT + GPIO_O_CR) |= 0x01;
HWREG(PUSHBUTTON_PORT + GPIO_O_LOCK) = 0;

GPIODirModeSet(PUSHBUTTON_PORT, LEFT_SWITCH | RIGHT_SWITCH , GPIO_DIR_MODE_IN);
GPIOPadConfigSet(PUSHBUTTON_PORT,LEFT_SWITCH | RIGHT_SWITCH , GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
GPIOPinIntDisable(PUSHBUTTON_PORT, LEFT_SWITCH | RIGHT_SWITCH);
if((GPIOPinIntStatus(PUSHBUTTON_PORT, 1)) == LEFT_SWITCH )
{
 GPIOPinIntClear(PUSHBUTTON_PORT, LEFT_SWITCH );
}
if((GPIOPinIntStatus(PUSHBUTTON_PORT, 1)) == RIGHT_SWITCH )
{
 GPIOPinIntClear(PUSHBUTTON_PORT, RIGHT_SWITCH );
}
ctl_set_priority(PUSHBUTTON_IRQ_PRIORITY, 1);
ctl_unmask_isr(PUSHBUTTON_IRQ_PRIORITY);
ctl_global_interrupts_set(en);
GPIOIntTypeSet(PUSHBUTTON_PORT, LEFT_SWITCH | RIGHT_SWITCH , GPIO_BOTH_EDGES); //GPIO_BOTH_EDGES
GPIOPinIntEnable(PUSHBUTTON_PORT, LEFT_SWITCH | RIGHT_SWITCH );
}

开发者ID:fegyizoli，项目名称:zolcsirobot，代码行数:29，代码来源:robot_buttons.c

示例7: hw_init

void hw_init(void){
	SysCtlClockSet(SYSCTL_SYSDIV_2_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);

	f_cpu = SysCtlClockGet();
	SysTickPeriodSet(0xffffffff);
	SysTickEnable();
//	UARTStdioInit();

	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
	GPIODirModeSet(SONAR_PORT, TRIG_PIN, GPIO_DIR_MODE_OUT);
	GPIODirModeSet(SONAR_PORT, SERVO_PIN, GPIO_DIR_MODE_OUT);

	GPIOPinTypeGPIOInput(SONAR_PORT, ECHO_PIN);
	GPIOIntTypeSet(SONAR_PORT, ECHO_PIN, GPIO_RISING_EDGE);
	GPIOPinIntEnable(SONAR_PORT,ECHO_PIN);
	IntEnable(INT_GPIOD);

	//Timer configuration
	SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
	TimerConfigure(TIMER0_BASE, TIMER_CFG_A_PERIODIC);
	const long timer_match = (f_cpu/1000000)*10;
	const long timer_out = (f_cpu/1000)*80;
	TimerLoadSet(TIMER0_BASE, TIMER_A, timer_out);
	TimerMatchSet(TIMER0_BASE, TIMER_A, timer_match);
	TimerEnable(TIMER0_BASE, TIMER_A);
	TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
	TimerIntClear(TIMER0_BASE,TIMER_A);
	IntEnable(INT_TIMER0A);

	IntMasterEnable();

}

开发者ID:gluker，项目名称:sonar，代码行数:32，代码来源:main.c

示例8: GPIO_PortF_IntHandler

void GPIO_PortF_IntHandler(void) {
	GPIOPinIntClear(GPIO_PORTF_BASE, GPIO_PIN_4);
	GPIOPinIntDisable(GPIO_PORTF_BASE, GPIO_PIN_4);
	Encoder_Count++;
	GPIOPinIntEnable(GPIO_PORTF_BASE, GPIO_PIN_4);

}

开发者ID:AlpNov，项目名称:Embedded-Robot，代码行数:7，代码来源:shaft_encoder.c

示例9: button_init

/**
 * Configures the used button as input source
 * Registers gpio_c interrupt..
 */
void button_init(){
	GPIOPinTypeGPIOInput(BSP_BUTTON_BASE, BSP_USER_BUTTON);
	GPIOIntTypeSet(BSP_BUTTON_BASE,BSP_USER_BUTTON,GPIO_FALLING_EDGE);
	GPIOPortIntRegister(BSP_BUTTON_BASE,GPIO_C_Isr_Handler);
	GPIOPinIntClear(BSP_BUTTON_BASE, BSP_USER_BUTTON);
	GPIOPinIntEnable(BSP_BUTTON_BASE, BSP_USER_BUTTON);
}

开发者ID:barriquello，项目名称:iotstack，代码行数:11，代码来源:board.c

示例10: init_spi

int init_spi(void)
{
  #if CFG_CC3000_SPI_PORT == 1
    ssp1Init();
  #else
    ssp0Init();
  #endif

  /* Set VBAT EN pin to output */
  LPC_GPIO->DIR[CFG_CC3000_EN_PORT] |= (1 << CFG_CC3000_EN_PIN);
  LPC_GPIO->SET[CFG_CC3000_EN_PORT]  = (1 << CFG_CC3000_EN_PIN);
  delay(100);

  /* Set CS pin to output */
  LPC_GPIO->DIR[CFG_CC3000_CS_PORT] |= (1 << CFG_CC3000_CS_PIN);
  CC3000_DEASSERT_CS;

  /* Set interrupt/gpio pin to input */
  LPC_GPIO->DIR[CFG_CC3000_IRQ_PORT]  &= ~(1 << CFG_CC3000_IRQ_PIN);

  /* Channel 2, sense (0=edge, 1=level), polarity (0=low/falling, 1=high/rising) */
  GPIOSetPinInterrupt( 2, CFG_CC3000_IRQ_PORT, CFG_CC3000_IRQ_PIN, 0, 1 );

  /* Enable interrupt 2 on falling edge */
  GPIOPinIntEnable( 2, 0 );

  return(ESUCCESS);
}

开发者ID:ismamont，项目名称:LPC11U_LPC13U_CodeBase，代码行数:28，代码来源:spi.c

示例11: GPIOPinIntClear

void GpioIn::enableInterrupts(void)
{
    // Clear the interrupt
    GPIOPinIntClear(gpio_.port, gpio_.pin);

    // Enable the interrupt
    GPIOPinIntEnable(gpio_.port, gpio_.pin);
}

开发者ID:openwarelab，项目名称:firmware，代码行数:8，代码来源:GpioIn.cpp

示例12: Transceiver_SendMessage

/******** Transceiver_SendMessage *******************************************
// unpack transceiver packet and send out
// Input:
//    pkt - transceiver packet to be sent 
// Output: status
// ------------------------------------------------------------------------*/
unsigned char Transceiver_SendMessage ( TransceiverPacket pkt )
{
	unsigned char tx[TRANSCEIVER_MAX_PAYLOAD];
	unsigned char index, length;
	unsigned char status = SUCCESS;

	// validate packet
	Debug_NetworkTransceiver_PrintPacket(&pkt);

	if ( MAX_DATA_SIZE < pkt.dataSize )
	{
		status = ERROR_INVALID_PAKCET;
		Debug_Printf ("Transceiver_SendMessage: Error 0x%x\n", status);
		goto exit;
	}

	// unpack transceiver packet
	tx[SOURCE_ID_INDEX] = pkt.srcID;
	tx[DEST_ID_INDEX] = pkt.destID;
	tx[MSG_ID_INDEX] = pkt.msgID;
	tx[DATA_SIZE_INDEX] = pkt.dataSize;
	length = DATA_INDEX;
	for ( index = 0; index < pkt.dataSize; index++,length++ )
	{
		tx[length] = pkt.data[index];
	}

	Debug_NetworkTransceiver_PrintPayload(tx);

	// lock transceiver
	while ( xSemaphoreTake(Transceiver_Mutex, portMAX_DELAY) != pdTRUE );
	GPIOPinIntDisable ( nrf24l01_IRQ_IOREGISTER, nrf24l01_IRQ_PIN );

	nrf24l01_set_as_tx();
	nrf24l01_write_tx_payload ( tx, TRANSCEIVER_MAX_PAYLOAD, true );

	//wait until the packet has been sent or the maximum number of retries has been active
	while( !( nrf24l01_irq_pin_active() && (nrf24l01_irq_tx_ds_active()||nrf24l01_irq_max_rt_active()) ) );
	if ( nrf24l01_irq_max_rt_active() )	
	{
		// hit maximum number of retries
		nrf24l01_flush_tx();
		status = ERROR_MAX_RETRIES;
		Debug_Printf ("Transceiver_SendMessage: Error 0x%x\n", status);
	}

	// reset transceiver
	nrf24l01_irq_clear_all();
	nrf24l01_set_as_rx(true);
	Delay_US(130);

	//unlock transceiver
	GPIOPinIntEnable ( nrf24l01_IRQ_IOREGISTER, nrf24l01_IRQ_PIN );
	while ( xSemaphoreGive(Transceiver_Mutex) != pdTRUE );

exit:
	return status;
}

开发者ID:yguo89，项目名称:CodeBrain，代码行数:64，代码来源:Transceiver.c

示例13: initHW

void
initHW(void)
{
  volatile unsigned long ulLoop;

  //initHW();

  SysCtlClockSet(
      SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_8MHZ);

  // Enable the ports
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
  SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);

  // Inputs :
  // PE0 : Up button
  // PE1 : Down button
  // PE2 : Left button
  // PE3 : Right button
  // PF1 : Select button
  //
  GPIODirModeSet(GPIO_PORTE_BASE,
      GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, GPIO_DIR_MODE_IN);
  GPIOPadConfigSet(GPIO_PORTE_BASE,
      GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, GPIO_STRENGTH_2MA,
      GPIO_PIN_TYPE_STD_WPU);

  GPIODirModeSet(GPIO_PORTF_BASE, GPIO_PIN_1, GPIO_DIR_MODE_IN);
  GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_1, GPIO_STRENGTH_2MA,
      GPIO_PIN_TYPE_STD_WPU);

  // Outputs:
  // PF0 : Status LED
  GPIODirModeSet(GPIO_PORTF_BASE, GPIO_PIN_0, GPIO_DIR_MODE_OUT);
  GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_0, GPIO_STRENGTH_2MA,
      GPIO_PIN_TYPE_STD);
  GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_0, 1);

  // Enable edge triggered interrupt on select button
  // Clear the interrupt just in case
  GPIOIntTypeSet(GPIO_PORTF_BASE, GPIO_PIN_1, GPIO_FALLING_EDGE);
  GPIOPinIntEnable(GPIO_PORTF_BASE, GPIO_PIN_1 );

  SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOF);


  // Enable the interrupt for port F
  IntEnable(INT_GPIOF);

  // Global interrupt enable
  IntMasterEnable();


  // a short delay to ensure stable IO before running the rest of the program
  for (ulLoop = 0; ulLoop < 200; ulLoop++)
    {
    }
}

开发者ID:BetteLars，项目名称:EAL_Embedded，代码行数:58，代码来源:main.c

示例14: vs_play

void vs_play(void)
{
  if(vs_request() && vs_playing)
  {
    GPIOPinIntEnable(GPIO_PORTA_BASE, GPIO_PIN_1); //enable dreq irq
  }

  return;
}

开发者ID:Bob4ik888，项目名称:WebRadio，代码行数:9，代码来源:vs.c

示例15: initMotor

//GPIO³õÊ¼»¯
void initMotor()
{
    //³õÊ¼»¯ÍâÉè¶Ë¿Ú
    SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
    SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
    
    //µç»úÕý·´×ª¿ØÖÆ¶Ë¿ÚÅäÖÃ
    GPIODirModeSet(GPIO_PORTD_BASE,  MOTOR_R0 | MOTOR_R1, GPIO_DIR_MODE_OUT);
    GPIOPadConfigSet(GPIO_PORTD_BASE, MOTOR_R0 | MOTOR_R1, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
    
    GPIODirModeSet(GPIO_PORTG_BASE,  MOTOR_L0 | MOTOR_L1, GPIO_DIR_MODE_OUT);
    GPIOPadConfigSet(GPIO_PORTG_BASE, MOTOR_L0 | MOTOR_L1, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);

    //±àÂëÆ÷ÖÐ¶ÏÉèÖÃ£¬ÏÂ½µÑØ´¥·¢    
    GPIODirModeSet(GPIO_PORTG_BASE, CODE_L, GPIO_DIR_MODE_IN); 
    GPIOPadConfigSet(GPIO_PORTG_BASE, CODE_L, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
    GPIOIntTypeSet(GPIO_PORTG_BASE, CODE_L, GPIO_FALLING_EDGE);
    GPIOPinIntEnable(GPIO_PORTG_BASE, CODE_L);
    
    GPIODirModeSet(GPIO_PORTD_BASE, CODE_R, GPIO_DIR_MODE_IN); 
    GPIOPadConfigSet(GPIO_PORTD_BASE, CODE_R, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
    GPIOIntTypeSet(GPIO_PORTD_BASE, CODE_R, GPIO_FALLING_EDGE);
    GPIOPinIntEnable(GPIO_PORTD_BASE, CODE_R);
    
    /*
    HWREG(GPIO_PORTB_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY_DD;
    // Set the commit register for PB7 to allow changing the function
    HWREG(GPIO_PORTB_BASE + GPIO_O_CR) = 0x80;
    // Enable the alternate function for PB7 (NMI)
    HWREG(GPIO_PORTB_BASE + GPIO_O_AFSEL) |= 0x80;
    // Turn on the digital enable for PB7
    HWREG(GPIO_PORTB_BASE + GPIO_O_DEN) |= 0x80;
    
    
    GPIODirModeSet(GPIO_PORTB_BASE,GPIO_PIN_7,GPIO_DIR_MODE_IN); 
    GPIOPadConfigSet(GPIO_PORTB_BASE,GPIO_PIN_7,GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD);
    GPIOIntTypeSet( GPIO_PORTB_BASE,GPIO_PIN_7,GPIO_FALLING_EDGE ); 
    // Relock the commit register
    HWREG(GPIO_PORTB_BASE + GPIO_O_LOCK) = 0;
    */
    
    IntEnable(INT_GPIOD);
    IntEnable(INT_GPIOG);
}

开发者ID:flyfire，项目名称:WebBasedRobot，代码行数:45，代码来源:motor.c

示例16: InitializeEncoders

void InitializeEncoders(tBoolean invert0, tBoolean invert1)
{
	// enable and configure the GPIO pins
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);	// enable the peripheral
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);	// enable the peripheral
	GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_4 | GPIO_PIN_6);	// configure pins as inputs
	GPIOPinTypeGPIOInput(GPIO_PORTC_BASE, GPIO_PIN_5 | GPIO_PIN_6);	// configure pins as inputs
	
	// enable and configure the interrupts
	IntEnable(INT_GPIOB);					// enable interrupts for the periph
	IntEnable(INT_GPIOC);					// enable interrupts for the periph
	GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_4 | GPIO_PIN_6, GPIO_BOTH_EDGES);	// configure the interrupts
	GPIOIntTypeSet(GPIO_PORTC_BASE, GPIO_PIN_5 | GPIO_PIN_6, GPIO_BOTH_EDGES);	// configure the interrupts
	GPIOPinIntEnable(GPIO_PORTB_BASE, GPIO_PIN_4 | GPIO_PIN_6);	// enable the interrupt for the pins
	GPIOPinIntEnable(GPIO_PORTC_BASE, GPIO_PIN_5 | GPIO_PIN_6);	// enable the interrupt for the pins
	
	dir0 = invert0 ? -1 : 1;
	dir1 = invert1 ? -1 : 1;
}

开发者ID:weng-frank，项目名称:RAS_LM3S811，代码行数:19，代码来源:encoder.c

示例17: main

int
main(void)
{

	
		
	//set clock	
	SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
                   SYSCTL_XTAL_8MHZ);


   
        

     //PB1
     SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
     GPIOPadConfigSet(GPIO_PORTB_BASE,GPIO_PIN_1,GPIO_STRENGTH_4MA,GPIO_PIN_TYPE_STD);
     GPIODirModeSet(GPIO_PORTB_BASE,GPIO_PIN_1,GPIO_DIR_MODE_IN);
     GPIOPortIntRegister(GPIO_PORTB_BASE, PortBIntHandler);
     GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_1, GPIO_BOTH_EDGES);
     GPIOPinIntEnable(GPIO_PORTB_BASE, GPIO_PIN_1);

        
    // Status
                SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
    GPIOPadConfigSet(GPIO_PORTF_BASE,GPIO_PIN_2,GPIO_STRENGTH_4MA,GPIO_PIN_TYPE_STD);
        GPIODirModeSet(GPIO_PORTF_BASE,GPIO_PIN_2,GPIO_DIR_MODE_OUT);  

    //UART
    SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
    SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
    GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
    UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 9600,
    (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
                   UART_CONFIG_PAR_NONE));
    IntEnable(INT_UART0);
    UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
   
    IntPrioritySet(INT_UART0, 0x7F);
                
    IntPrioritySet(INT_GPIOB,0x80);
    IntMasterEnable();
    SysTickIntRegister(SysTickHandler);                  
    SysTickPeriodSet(SysCtlClockGet()/10000);   // 0.1ms
    SysTickIntEnable();
    waitTime = 0;                   // initialize
    waitTime2 = 0;
    SysTickEnable();
    while(1)
    {
 

    }
    
}

开发者ID:richardszeto，项目名称:Embedded_Systems，代码行数:55，代码来源:Lab3_2110.c

示例18: halRfRxInterruptConfig

/***********************************************************************************
* @fn      halRfRxInterruptConfig
*
* @brief   Enable RX interrupt.
*
* @param   none
*
* @return  none
*/
void halRfRxInterruptConfig(ISR_FUNC_PTR pfISR)
{
//	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//	GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_1);				/* Default pin is Push-pull.*/
	GPIOPadConfigSet(GPIO_PORTD_BASE, GPIO_PIN_0, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPD);
	GPIOIntTypeSet(GPIO_PORTD_BASE, GPIO_PIN_0, GPIO_RISING_EDGE);	/* Rising edge is active.*/
	GPIOPortIntRegister(GPIO_PORTD_BASE, pfISR);
	GPIOPinIntEnable(GPIO_PORTD_BASE, GPIO_PIN_0);
	
    CLEAR_EXC_RX_FRM_DONE();										/* And clear the exception.*/
}

开发者ID:navinars，项目名称:etz-main，代码行数:20，代码来源:hal_rf.c

示例19: flipPancake

void flipPancake(void) {
	GPIOPinIntDisable(GPIO_PORTA_BASE, GPIO_PIN_2);
	WaitUS(2000);
	GPIOPinIntClear(GPIO_PORTA_BASE, GPIO_PIN_2);
	if(!GPIOPinRead(GPIO_PORTA_BASE,GPIO_PIN_2))
	{
		UARTprintf("Triggered.\n");
		SetServoPosition(PANCAKE_POSITION,100*pancake);
		pancake = !pancake;
	}
	GPIOPinIntEnable(GPIO_PORTA_BASE, GPIO_PIN_2);
}

开发者ID:RAS-MoFos，项目名称:Rasware2012，代码行数:12，代码来源:Nav.c

示例20: intButton

void intButton (void)
{
	SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
	// Register the handler for Port B into the vector table
	GPIOPortIntRegister (GPIO_PORTB_BASE, ButtPressIntHandler);

	//Initialising for buttons
	GPIOPinTypeGPIOInput (GPIO_PORTB_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_6);
	GPIOPadConfigSet (GPIO_PORTB_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_6, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
	GPIOIntTypeSet (GPIO_PORTB_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_6, GPIO_FALLING_EDGE);
	GPIOPinIntEnable (GPIO_PORTB_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_6);

}

开发者ID:Yamoahs，项目名称:ENCE361_Helicopter_project，代码行数:13，代码来源:Copy+of+milestone2_MotorControl(PID)4.c

注：本文中的GPIOPinIntEnable函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ GPIOPinRead函数代码示例发布时间：2022-05-30

C++ GPIOPinIntClear函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19200|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9989|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8328|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8697|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8640|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9659|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8625|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8000|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8657|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7536|2022-11-06

客服电话

电子邮件

C++ GPIOPinIntEnable函数代码示例

示例1: main

示例2: initYaw

示例3: setup

示例4: GPIO_SetInterruptTask

示例5: Transceiver_ReceiveMessage

示例6: ctl_buttons_isr_init

示例7: hw_init

示例8: GPIO_PortF_IntHandler

示例9: button_init

示例10: init_spi

示例11: GPIOPinIntClear

示例12: Transceiver_SendMessage

示例13: initHW

示例14: vs_play

示例15: initMotor

示例16: InitializeEncoders

示例17: main

示例18: halRfRxInterruptConfig

示例19: flipPancake

示例20: intButton

请发表评论

全部评论

上一篇：

下一篇：

nirenr/AndroLua_pro: Lua5.3.3 for androi

samhitha1/demo: Sample for ANT/Maven Scr

geb/geb-example-maven

senryulearning/MastodonWikiSenryu

rstropek/pandoc-latex: Extended version

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053