C++ EXTI_Init函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中EXTI_Init函数的典型用法代码示例。如果您正苦于以下问题：C++ EXTI_Init函数的具体用法？C++ EXTI_Init怎么用？C++ EXTI_Init使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了EXTI_Init函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: HAL_Interrupts_Detach

void HAL_Interrupts_Detach(uint16_t pin)
{
  //Map the Spark Core pin to the appropriate pin on the STM32
  STM32_Pin_Info* PIN_MAP = HAL_Pin_Map();
  uint16_t gpio_pin = PIN_MAP[pin].gpio_pin;
  uint8_t GPIO_PinSource = PIN_MAP[pin].gpio_pin_source;

  //Clear the pending interrupt flag for that interrupt pin
  EXTI_ClearITPendingBit(gpio_pin);

  //EXTI structure to init EXT
  EXTI_InitTypeDef EXTI_InitStructure = {0};

  //Select the appropriate EXTI line
  EXTI_InitStructure.EXTI_Line = gpio_pin;
  //disable that EXTI line
  EXTI_InitStructure.EXTI_LineCmd = DISABLE;
  //send values to registers
  EXTI_Init(&EXTI_InitStructure);

  //unregister the user's handler
  exti_channels[GPIO_PinSource].fn = NULL;
  exti_channels[GPIO_PinSource].data = NULL;
}

开发者ID:Babbleshack，项目名称:firmware，代码行数:24，代码来源:interrupts_hal.c

示例2: EXTI_PC13_Config

 /**
  * @brief  配置 PC13 为线中断口，并设置中断优先级
  * @param  无
  * @retval 无
  */
void EXTI_PC13_Config(void)
{
	GPIO_InitTypeDef GPIO_InitStructure; 
	EXTI_InitTypeDef EXTI_InitStructure;

	/* config the extiline(PC13) clock and AFIO clock */
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO,ENABLE);
												
	/* config the NVIC(PC13) */
	NVIC_Configuration();

	/* EXTI line gpio config(PC13) */	
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;       
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;	 // 上拉输入
  GPIO_Init(GPIOC, &GPIO_InitStructure);

	/* EXTI line(PC13) mode config */
  GPIO_EXTILineConfig(GPIO_PortSourceGPIOC, GPIO_PinSource13); 
  EXTI_InitStructure.EXTI_Line = EXTI_Line13;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling; //下降沿中断
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure); 
}

开发者ID:ChijunShen，项目名称:wildfire_stm32_iso，代码行数:29，代码来源:bsp_exti.c

示例3: EXTI_Init

void CRF::SetIRQ(FunctionalState state)
{
	if (m_IRQ_BB)
	{
		EXTI_InitTypeDef EXTI_InitStructure;
		EXTI_InitStructure.EXTI_Line = m_IRQ;
		EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
		EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
		EXTI_InitStructure.EXTI_LineCmd = state;
		EXTI_Init(&EXTI_InitStructure);
		GPIO_EXTILineConfig(GPIO_PORT_NUM(m_IRQ_GPIO), GPIO_PIN_NUM_FROM_BB(m_IRQ_BB));
		
		// Clear pending interrupt before enabling it.
		EXTI_ClearITPendingBit(m_IRQ);
    		NVIC_ClearPendingIRQ(m_IRQn);

		NVIC_InitTypeDef NVIC_InitStructure;
		NVIC_InitStructure.NVIC_IRQChannel = m_IRQn;
		NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
		NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
		NVIC_InitStructure.NVIC_IRQChannelCmd = state;
		NVIC_Init(&NVIC_InitStructure);
	}
}

开发者ID:houguozhi，项目名称:HS6206_CP_GS_MCU_FM，代码行数:24，代码来源:rf.cpp

示例4: EnExtInter

void EnExtInter() {
	//EXTI_X must be equal to pin_Yx.. you can choose Y as ABCD but NOT the X number pin0(abcd)->Exti0->irq0

	//GPIO_EXTILineConfig(GPIO_PortSourceGPIOA , GPIO_PinSource0);

     EXTI_InitTypeDef EXTI_InitStructure;

     /* Configure EXTI Line0 */
     EXTI_InitStructure.EXTI_Line = EXTI_Line0;
     EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
     EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
     EXTI_InitStructure.EXTI_LineCmd = ENABLE;
     EXTI_Init(&EXTI_InitStructure);

     /* Enable and set EXTI Line0 Interrupt to the lowest priority */
     NVIC_InitTypeDef NVIC_InitStructure;
     NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
     NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x01;
     NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01;
     NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
     NVIC_Init(&NVIC_InitStructure);


}

开发者ID:Broentech，项目名称:Vri_fog_device，代码行数:24，代码来源:interHandler.c

示例5: hcsr04_init

void hcsr04_init(const sonarHardware_t *initialSonarHardware)
{
    gpio_config_t gpio;
    EXTI_InitTypeDef EXTIInit;

    sonarHardware = initialSonarHardware;

    // enable AFIO for EXTI support
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);

    // tp - trigger pin
    gpio.pin = sonarHardware->trigger_pin;
    gpio.mode = Mode_Out_PP;
    gpio.speed = Speed_2MHz;
    gpioInit(GPIOB, &gpio);

    // ep - echo pin
    gpio.pin = sonarHardware->echo_pin;
    gpio.mode = Mode_IN_FLOATING;
    gpioInit(GPIOB, &gpio);

    // setup external interrupt on echo pin
    gpioExtiLineConfig(GPIO_PortSourceGPIOB, sonarHardware->exti_pin_source);

    EXTI_ClearITPendingBit(sonarHardware->exti_line);

    EXTIInit.EXTI_Line = sonarHardware->exti_line;
    EXTIInit.EXTI_Mode = EXTI_Mode_Interrupt;
    EXTIInit.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
    EXTIInit.EXTI_LineCmd = ENABLE;
    EXTI_Init(&EXTIInit);

    NVIC_EnableIRQ(sonarHardware->exti_irqn);

    last_measurement = millis() - 60; // force 1st measurement in hcsr04_get_distance()
}

开发者ID:AhLeeYong，项目名称:cleanflight，代码行数:36，代码来源:sonar_hcsr04.c

示例6: VSYNC_EXTI_Configuration

/**
 *  @name	VSYNC_EXTI_Configuration
 *  @brief	配置PB7为外部中断引脚
 *  @param  None        
 *  @return None
 *  @notice
	                ___                            ___
	  VSYNC:     __|   |__________________________|   |__     
	 
 */
static void VSYNC_EXTI_Configuration(void)
{
	CKCU_PeripClockConfig_TypeDef CKCUClock = {{0}};
	EXTI_InitTypeDef EXTI_InitStruct;
	
	/* Enable PB & AFIO & EXTI */
	CKCUClock.Bit.PB         = 1;
	CKCUClock.Bit.AFIO 		 = 1;
	CKCUClock.Bit.EXTI 		 = 1;
	CKCU_PeripClockConfig(CKCUClock, ENABLE);

	/* Config EXTI channel 7 */
	EXTI_InitStruct.EXTI_Channel = EXTI_CHANNEL_7;
	EXTI_InitStruct.EXTI_Debounce = EXTI_DEBOUNCE_DISABLE;
	EXTI_InitStruct.EXTI_DebounceCnt = 0;
	EXTI_InitStruct.EXTI_IntType = EXTI_NEGATIVE_EDGE;
	EXTI_Init(&EXTI_InitStruct);
	
	/* Select Port as EXTI Trigger Source */
	AFIO_EXTISourceConfig(AFIO_EXTI_CH_7, AFIO_ESS_PB);
	
	/* Enable EXTI line 7 Interrupt                                                                          */
	EXTI_IntConfig(EXTI_CHANNEL_7, ENABLE);
}

开发者ID:gaunthan，项目名称:SmartHelmet，代码行数:34，代码来源:ov7670.c

示例7: eth_nvic

int eth_nvic(struct driver * driver)
{
	EXTI_InitTypeDef EXTI_InitStructure;
  NVIC_InitTypeDef NVIC_InitStructure;
	
	/* Connect EXTI Line to INT Pin */
  SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOH, EXTI_PinSource6);
	
	/* Configure EXTI line */
  EXTI_InitStructure.EXTI_Line = EXTI_Line6;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure);

  /* Enable and set the EXTI interrupt to the highest priority */
  NVIC_InitStructure.NVIC_IRQChannel = EXTI9_5_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 4;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
	
	return 0;
}

开发者ID:zhumj1991，项目名称:general-bsp，代码行数:24，代码来源:eth.c

示例8: EXTILine13_Config

/**
  * @brief  Configures EXTI Line15 (connected to PG15 pin) in interrupt mode
  * @param  None
  * @retval None
  */
static void EXTILine13_Config(void)
{
  EXTI_InitTypeDef   EXTI_InitStructure;
  GPIO_InitTypeDef   GPIO_InitStructure;
  NVIC_InitTypeDef   NVIC_InitStructure;

  /* Enable GPIOC clock */
  RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
  
  /* Enable SYSCFG clock */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
  
  /* Configure PC13 pin as input floating */
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
  GPIO_Init(GPIOC, &GPIO_InitStructure);

  /* Connect EXTI Line15 to PC13 pin */
  SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOC, EXTI_PinSource13);

  /* Configure EXTI Line13 */
  EXTI_InitStructure.EXTI_Line = EXTI_Line13;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure);

  /* Enable and set EXTI15_10 Interrupt to the lowest priority */
  NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x0F;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x0F;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;

  NVIC_Init(&NVIC_InitStructure);
}

开发者ID:iGaryGu，项目名称:Painter，代码行数:41，代码来源:main.c

示例9: EXTI_PC13_Config

void EXTI_PC13_Config(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	EXTI_InitTypeDef EXTI_InitStructure;
	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC|RCC_APB2Periph_AFIO,ENABLE);
	
	NVIC_Configuration();
	
	
	GPIO_InitStructure.GPIO_Pin=GPIO_Pin_13;
	
	GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IPU;
	GPIO_Init(GPIOC,&GPIO_InitStructure);
	
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOC,GPIO_PinSource13);
	EXTI_InitStructure.EXTI_Line=EXTI_Line13;
	EXTI_InitStructure.EXTI_Mode=EXTI_Mode_Interrupt;
	EXTI_InitStructure.EXTI_Trigger=EXTI_Trigger_Falling;
	
	EXTI_InitStructure.EXTI_LineCmd =ENABLE;
	EXTI_Init(&EXTI_InitStructure);
	
}

开发者ID:xyzzhangfan，项目名称:aircondition-control，代码行数:24，代码来源:exit.c

示例10: EXTILine_Config

/**
  * @brief  Configures EXTI Line0 (connected to PA0 pin) in interrupt mode
  * @param  None
  * @retval None
  */
static void EXTILine_Config(void)
{
  GPIO_InitTypeDef   GPIO_InitStructure;
  NVIC_InitTypeDef   NVIC_InitStructure;
  EXTI_InitTypeDef   EXTI_InitStructure;
	
  /* Enable GPIOA clock */
  RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
  /* Enable SYSCFG clock */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
	
  /* Configure PE0 and PE1 pins as input floating */
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  /* Connect EXTI Line to PE1 pins */
  SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, EXTI_PinSource0);

  /* Configure EXTI Line1 */
  EXTI_InitStructure.EXTI_Line = EXTI_Line0;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;  
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure);

  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_4);
  
  /* Enable and set EXTI Line0 Interrupt to the lowest priority */
  NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x00;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x00;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
}

开发者ID:emanuelribeiro，项目名称:projeto1，代码行数:41，代码来源:waveplayer.c

示例11: SysTick_Handler

void SysTick_Handler(void)
{
	if(dht22_data->metering_stage == DHT22_done)
		return;
	if(dht22_data->metering_stage == DHT22_sendStrobe0) {
		// 3.1
		GPIO_initStruct.GPIO_Pin = DHT22_PIN;
		GPIO_initStruct.GPIO_Mode = GPIO_Mode_IN;
		GPIO_Init(DHT22_PORT, &GPIO_initStruct);
		// 3.2
		dht22_data->metering_stage = DHT22_waitRisingEdge;
		SysTick_Config(dht22_data->timeout);
		// 3.3
		SYSCFG_EXTILineConfig(DHT22_EXTI_PORT, DHT22_PIN_NUM);
		EXTI_initStruct.EXTI_Line = DHT22_EXTI_LINE;
		EXTI_initStruct.EXTI_Mode = EXTI_Mode_Interrupt;
		EXTI_initStruct.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
		EXTI_initStruct.EXTI_LineCmd = ENABLE;
		EXTI_Init(&EXTI_initStruct);

		NVIC_initStruct.NVIC_IRQChannel = EXTI4_15_IRQn;
		NVIC_initStruct.NVIC_IRQChannelPriority = 0x00;
		NVIC_initStruct.NVIC_IRQChannelCmd = ENABLE;
		NVIC_Init(&NVIC_initStruct);
	}
	else {
		// 3.4
		SysTick->CTRL &= ~(SysTick_CTRL_TICKINT_Msk | SysTick_CTRL_ENABLE_Msk);
		NVIC_initStruct.NVIC_IRQChannel = EXTI4_15_IRQn;
		NVIC_initStruct.NVIC_IRQChannelPriority = 0x00;
		NVIC_initStruct.NVIC_IRQChannelCmd = DISABLE;
		NVIC_Init(&NVIC_initStruct);
		dht22_data->result = DHT22_ERR_TIMEOUT;
		dht22_data->done_cb(dht22_data);
	}
}

开发者ID:andrey-perepelitsyn，项目名称:stm32，代码行数:36，代码来源:dht22.c

示例12: xxxx

void xxxx(void)
{
	GPIO_InitTypeDef   GPIO_InitStructure;
	EXTI_InitTypeDef EXTI_InitStructure;
	NVIC_InitTypeDef NVIC_InitStructure;

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
    GPIO_Init(GPIOC, &GPIO_InitStructure);

	GPIO_EXTILineConfig(GPIO_PortSourceGPIOC, GPIO_PinSource0);
	EXTI_InitStructure.EXTI_Line = EXTI_Line0;
	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
	EXTI_Init(&EXTI_InitStructure);

	NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);
}

开发者ID:294250581，项目名称:TMCS，代码行数:24，代码来源:main.c

示例13: Gpio_Int_Init_adns9800

void Gpio_Int_Init_adns9800(void)
{
  
  EXTI_InitTypeDef   EXTI_InitStructure;
  GPIO_InitTypeDef   GPIO_InitStructure;
  NVIC_InitTypeDef   NVIC_InitStructure;
  
  /* Enable GPIOA clock */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
  
  /* Configure PA.00 pin as input floating */
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
  //GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPD;
  GPIO_Init(GPIOA, &GPIO_InitStructure);
  
  /* Enable AFIO clock */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
  
  /* Connect EXTI0 Line to PA.00 pin */
  GPIO_EXTILineConfig(GPIO_PortSourceGPIOA, GPIO_PinSource0);
  
  /* Configure EXTI0 line */
  EXTI_InitStructure.EXTI_Line = EXTI_Line0;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;  
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure);
  
  /* Enable and set EXTI0 Interrupt to the lowest priority */
  NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x00;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x00;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
}

开发者ID:li77leprince，项目名称:Laparoscopic，代码行数:36，代码来源:adns9200.c

示例14: Camera_NVIC_Configuration

/****************************************************************************
* 名    称：void NVIC_Configuration(void)
* 功    能：中断源配置
* 入口参数：无
* 出口参数：无
* 说    明：
* 调用方法：无
****************************************************************************/
void Camera_NVIC_Configuration(void)
{
    NVIC_InitTypeDef NVIC_InitStructure;
    EXTI_InitTypeDef EXTI_InitStructure;
    /* Configure one bit for preemption priority */
    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);

    NVIC_InitStructure.NVIC_IRQChannel = EXTI4_IRQn ;				 //外部中断4
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;	     //抢占优先级 0
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;			 //子优先级0
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;				 //使能
    NVIC_Init(&NVIC_InitStructure);

    //用于配置AFIO外部中断配置寄存器AFIO_EXTICR1，用于选择EXTI4外部中断的输入源是PE4。
    GPIO_EXTILineConfig(GPIO_PortSourceGPIOE, GPIO_PinSource4);     //外部中断配置AFIO--ETXI4

    EXTI_InitStructure.EXTI_Line = EXTI_Line4;					  //PE4 作为摄像头帧同步检测 检测一帧FIFO接收完成
    EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;			  //中断模式
    EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;		  //下降沿触发
    EXTI_InitStructure.EXTI_LineCmd = ENABLE;
    EXTI_Init(&EXTI_InitStructure);


}

开发者ID:wareash，项目名称:stm32-camera，代码行数:32，代码来源:OV7670.c

示例15: EXTI_NVIC_Config_PushButton

/*
 * Function: EXTI_NVIC_Config_PushButton
 * ----------------------------
 * Configure EXTI and NVIC pin PA0 line0 for push button interrupts
 *   Returns: void
 *
 *   @param: none
 *   returns: none
 */
void EXTI_NVIC_Config_PushButton(void)
{
	GPIO_InitTypeDef GPIO_MEM_Init_struct;
	EXTI_InitTypeDef EXTI_MEM_struct;
	NVIC_InitTypeDef NVIC_MEM_struct;
	
	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
	// Enable SYSCFG clock 
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
	
	GPIO_StructInit(&GPIO_MEM_Init_struct);
	
	GPIO_MEM_Init_struct.GPIO_Mode = GPIO_Mode_IN;
	GPIO_MEM_Init_struct.GPIO_Pin = GPIO_Pin_0;
	GPIO_MEM_Init_struct.GPIO_PuPd = GPIO_PuPd_NOPULL;
  
	GPIO_Init(GPIOA, &GPIO_MEM_Init_struct);
	
	SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, EXTI_PinSource0);
	
	EXTI_MEM_struct.EXTI_Line = EXTI_Line0;
  EXTI_MEM_struct.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_MEM_struct.EXTI_Trigger = EXTI_Trigger_Rising;  
  EXTI_MEM_struct.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_MEM_struct);

  /* Enable and set EXTI Line0 Interrupt */ 
  NVIC_MEM_struct.NVIC_IRQChannel = EXTI0_IRQn;
  NVIC_MEM_struct.NVIC_IRQChannelPreemptionPriority = 0x01;
  NVIC_MEM_struct.NVIC_IRQChannelSubPriority = 0x02; // set priority to 2, accelerometer data ready interrupts gets priority of 1
  NVIC_MEM_struct.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_MEM_struct);
	
	return;

}

开发者ID:YangZhou91，项目名称:MicroP-Project，代码行数:45，代码来源:main.c

示例16: EXTI_ONOFF_EN

/**
  * @brief  Configure on/off pin interrupt
  * @param  None
  * @retval None
  * This initialiser function assumes the clocks and gpio have been configured
  */
void EXTI_ONOFF_EN(void) {
	EXTI_InitTypeDef   EXTI_InitStructure;
	NVIC_InitTypeDef   NVIC_InitStructure;
	EXTI_DeInit();
	/* Connect EXTI0 Line to PA.0 pin - WKUP*/
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOA, GPIO_PinSource0);

	/* Configure EXTI0 line */
	EXTI_InitStructure.EXTI_Line = EXTI_Line0;
	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
	if(USB_SOURCE==bootsource)				//If we booted from USB, disconnect gives -ive pulse
		EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
	else
		EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;  
	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
	EXTI_Init(&EXTI_InitStructure);

	/* Enable and set EXTI0 Interrupt to the lowest priority */
	NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;	//The WKUP triggered interrupt	
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x01;//Lower pre-emption priority
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x07;	//lowest group priority
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);
}

开发者ID:offchooffcho，项目名称:STM32-Logger，代码行数:30，代码来源:interrupts.c

示例17: gpio_irq_set

void gpio_irq_set(gpio_irq_t *obj, gpio_irq_event event, uint32_t enable) {
    EXTI_InitTypeDef EXTI_InitStructure;
    
    uint32_t pin_index = channel_pin[obj->irq_index];

    EXTI_InitStructure.EXTI_Line = (uint32_t)(1 << pin_index);
    EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
    
    if (event == IRQ_RISE) {
        if ((obj->event == EDGE_FALL) || (obj->event == EDGE_BOTH)) {
            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
            obj->event = EDGE_BOTH;
        } else { // NONE or RISE
            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
            obj->event = EDGE_RISE;
        }
    }
    
    if (event == IRQ_FALL) {
        if ((obj->event == EDGE_RISE) || (obj->event == EDGE_BOTH)) {
            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
            obj->event = EDGE_BOTH;
        } else { // NONE or FALL
            EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
            obj->event = EDGE_FALL;
        }
    }
    
    if (enable) {
        EXTI_InitStructure.EXTI_LineCmd = ENABLE;
    } else {
        EXTI_InitStructure.EXTI_LineCmd = DISABLE;
    }
    
    EXTI_Init(&EXTI_InitStructure);
}

开发者ID:AsamQi，项目名称:mbed，代码行数:36，代码来源:gpio_irq_api.c

示例18: IrInit

void IrInit(void)
{
    GPIO_InitTypeDef   GPIO_InitStructure;
    EXTI_InitTypeDef   EXTI_InitStructure;
    NVIC_InitTypeDef   NVIC_InitStructure;

    GPIO_InitStructure.GPIO_Pin = IRSEND_PIN;     //设置IO模式
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(IR_PORT, &GPIO_InitStructure);

    GPIO_InitStructure.GPIO_Pin = IRRED_PIN;     //设置IO模式
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;    //必须要上拉
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(IR_PORT, &GPIO_InitStructure);

    /* Connect EXTI0 Line to PA.00 pin */
    GPIO_EXTILineConfig(GPIO_PortSourceGPIOA, GPIO_PinSource4); //设定外设中断线。


    EXTI_ClearITPendingBit(EXTI_Line4);       //清除线路挂起位
    /* Configure EXTI0 line */
    EXTI_InitStructure.EXTI_Line = EXTI_Line4;     //设置中断类型
    EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
    EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;    //上升沿触发
    EXTI_InitStructure.EXTI_LineCmd = ENABLE;
    EXTI_Init(&EXTI_InitStructure);


    /* Enable and set EXTI0 Interrupt to the lowest priority */
    NVIC_InitStructure.NVIC_IRQChannel = EXTI4_IRQn;      //设置中断优先级
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);
}

开发者ID:powerorigin，项目名称:nethub，代码行数:36，代码来源:IR.c

示例19: RTC_AlarmConfig

/**
  * @brief  Configures the RTC Alarm.
  * @param  None
  * @retval None
  */
static void RTC_AlarmConfig(void)
{
  EXTI_InitTypeDef EXTI_InitStructure;
  RTC_AlarmTypeDef RTC_AlarmStructure;
  NVIC_InitTypeDef NVIC_InitStructure;
  
  /* EXTI configuration */
  EXTI_ClearITPendingBit(EXTI_Line17);
  EXTI_InitStructure.EXTI_Line = EXTI_Line17;
  EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
  EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
  EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  EXTI_Init(&EXTI_InitStructure);
  
  /* Enable the RTC Alarm Interrupt */
  NVIC_InitStructure.NVIC_IRQChannel = RTC_Alarm_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
 
  /* Set the alarm A Masks */
  RTC_AlarmStructure.RTC_AlarmMask = RTC_AlarmMask_All;
  RTC_AlarmStructure.RTC_AlarmDateWeekDaySel = RTC_AlarmDateWeekDaySel_Date;
  RTC_AlarmStructure.RTC_AlarmDateWeekDay = RTC_Weekday_Monday;
  RTC_AlarmStructure.RTC_AlarmTime.RTC_Hours = 0x0;
  RTC_AlarmStructure.RTC_AlarmTime.RTC_Minutes =0x0;
  RTC_AlarmStructure.RTC_AlarmTime.RTC_Seconds =0x0;
  RTC_SetAlarm(RTC_Format_BCD, RTC_Alarm_A, &RTC_AlarmStructure);
  
  /* Set alarm A sub seconds and enable SubSec Alarm : generate 8 interrupts per Second */
  RTC_AlarmSubSecondConfig(RTC_Alarm_A, 0xFF, RTC_AlarmSubSecondMask_SS14_5);

  /* Enable alarm A interrupt */
  RTC_ITConfig(RTC_IT_ALRA, ENABLE);
}

开发者ID:Haensi2000，项目名称:ECSE426G7，代码行数:41，代码来源:main.c

示例20: PBInit

/**
  * @brief  Configures Button GPIO and EXTI Line.
  * @param  Button: Specifies the Button to be configured.
  *   This parameter can be one of following parameters:
  *     @arg USR1_BUTTON: User Push Button 1
  *     @arg USR2_BUTTON: User Push Button 2
  * @param  Button_Mode: Specifies Button mode.
  *   This parameter can be one of following parameters:
  *     @arg BUTTON_MODE_GPIO: Button will be used as simple IO
  *     @arg BUTTON_MODE_EXTI: Button will be connected to EXTI line with interrupt
  *                     generation capability
  * @retval None
  */
void PBInit(Button_TypeDef Button, ButtonMode_TypeDef Button_Mode)
{
  GPIO_InitTypeDef GPIO_InitStructure;
  EXTI_InitTypeDef EXTI_InitStructure;
  NVIC_InitTypeDef NVIC_InitStructure;

  /* Enable the BUTTON Clock */
  RCC_AHBPeriphClockCmd(BUTTON_CLK[Button], ENABLE);
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);

  /* Configure Button pin as input */
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
  GPIO_InitStructure.GPIO_Pin = BUTTON_PIN[Button];
  GPIO_Init(BUTTON_PORT[Button], &GPIO_InitStructure);

  if (Button_Mode == BUTTON_MODE_EXTI)
  {
    /* Connect Button EXTI Line to Button GPIO Pin */
    SYSCFG_EXTILineConfig(BUTTON_PORT_SOURCE[Button], BUTTON_PIN_SOURCE[Button]);

    /* Configure Button EXTI line */
    EXTI_InitStructure.EXTI_Line = BUTTON_EXTI_LINE[Button];
    EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
    EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
    EXTI_InitStructure.EXTI_LineCmd = ENABLE;
    EXTI_Init(&EXTI_InitStructure);

    /* Enable and set Button EXTI Interrupt to the lowest priority */
    NVIC_InitStructure.NVIC_IRQChannel = BUTTON_IRQn[Button];
    NVIC_InitStructure.NVIC_IRQChannelPriority = 0x03;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;

    NVIC_Init(&NVIC_InitStructure);
  }
}

开发者ID:w1171325281，项目名称:STM32F051X8，代码行数:49，代码来源:stm320Fxx_ksk.c

注：本文中的EXTI_Init函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ EXTRACT16函数代码示例发布时间：2022-05-30

C++ EXTI_ClearITPendingBit函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19166|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9981|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8321|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8690|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8634|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9650|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8617|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7994|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8648|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7531|2022-11-06

客服电话

电子邮件

C++ EXTI_Init函数代码示例

示例1: HAL_Interrupts_Detach

示例2: EXTI_PC13_Config

示例3: EXTI_Init

示例4: EnExtInter

示例5: hcsr04_init

示例6: VSYNC_EXTI_Configuration

示例7: eth_nvic

示例8: EXTILine13_Config

示例9: EXTI_PC13_Config

示例10: EXTILine_Config

示例11: SysTick_Handler

示例12: xxxx

示例13: Gpio_Int_Init_adns9800

示例14: Camera_NVIC_Configuration

示例15: EXTI_NVIC_Config_PushButton

示例16: EXTI_ONOFF_EN

示例17: gpio_irq_set

示例18: IrInit

示例19: RTC_AlarmConfig

示例20: PBInit

请发表评论

全部评论

上一篇：

下一篇：

Ubuntu14.04下安装matlab2014a

bradtraversy/iweather: Ionic 3 mobile we

CVE-2020-27732

joaomh/curso-de-matlab

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053