• 设为首页
  • 点击收藏
  • 手机版
    手机扫一扫访问
    迪恩网络手机版
  • 关注官方公众号
    微信扫一扫关注
    公众号

C++ CPU_REG函数代码示例

原作者: [db:作者] 来自: [db:来源] 收藏 邀请

本文整理汇总了C++中CPU_REG函数的典型用法代码示例。如果您正苦于以下问题:C++ CPU_REG函数的具体用法?C++ CPU_REG怎么用?C++ CPU_REG使用的例子?那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。



在下文中一共展示了CPU_REG函数的20个代码示例,这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞,您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: ack_gpio_irq

/*
 * ack GPIO irq's
 * Ack only for edge triggered int's valid
 */
static void inline ack_gpio_irq(u32 irq)
{
	u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(irq));
	u32 bit = IRQ_TO_BIT(irq);
	if ( (CPU_REG (reg_base, GPIO_EDGE) & bit))
		CPU_REG (reg_base, GPIO_CLR) = bit;
}
开发者ID:ForayJones,项目名称:iods,代码行数:11,代码来源:common.c


示例2: ack_gpio_irq

/*
 * ack GPIO irq's
 * Ack only for edge triggered int's valid
 */
static void inline ack_gpio_irq(struct irq_data *d)
{
	u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(d->irq));
	u32 bit = IRQ_TO_BIT(d->irq);
	if ( (CPU_REG (reg_base, GPIO_EDGE) & bit))
		CPU_REG (reg_base, GPIO_CLR) = bit;
}
开发者ID:Jackeagle,项目名称:android_kernel_sony_c2305,代码行数:11,代码来源:common.c


示例3: init_eval_h7202

/*
 * Hardware init. This is called early in initcalls
 * Place pin inits here. So you avoid adding ugly
 * #ifdef stuff to common drivers.
 * Use this only, if your bootloader is not able
 * to initialize the pins proper.
 */
static void __init init_eval_h7202(void)
{
	init_hw_h7202();
	(void) platform_add_devices(devices, ARRAY_SIZE(devices));

	/* Enable interrupt on portb bit 8 (ethernet) */
	CPU_REG (GPIO_B_VIRT, GPIO_POL) &= ~(1 << 8);
	CPU_REG (GPIO_B_VIRT, GPIO_EN) |= (1 << 8);
}
开发者ID:8497165,项目名称:JetKernel,代码行数:16,代码来源:h7202-eval.c


示例4: init_eval_h7202

static void __init init_eval_h7202(void)
{
	init_hw_h7202();
	(void) platform_add_devices(devices, ARRAY_SIZE(devices));

	/*                                            */
	CPU_REG (GPIO_B_VIRT, GPIO_POL) &= ~(1 << 8);
	CPU_REG (GPIO_B_VIRT, GPIO_EN) |= (1 << 8);
}
开发者ID:curbthepain,项目名称:android_kernel_us990_rev,代码行数:9,代码来源:h7202-eval.c


示例5: h720x__idle

static void h720x__idle(void)
{
	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
	nop();
	nop();
	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_RUN;
	nop();
	nop();
}
开发者ID:Jackeagle,项目名称:android_kernel_sony_c2305,代码行数:9,代码来源:common.c


示例6: h7202_init_time

/*
 * Setup TIMER0 as system timer
 */
void __init h7202_init_time(void)
{
	CPU_REG (TIMER_VIRT, TM0_PERIOD) = LATCH;
	CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_RESET;
	CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_REPEAT | TM_START;
	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) = ENABLE_TM0_INTR | TIMER_ENABLE_BIT;

	setup_irq(IRQ_TIMER0, &h7202_timer_irq);
}
开发者ID:1x23,项目名称:unifi-gpl,代码行数:12,代码来源:cpu-h7202.c


示例7: init_hw_h7202

void __init init_hw_h7202(void)
{
	/* Enable clocks */
	CPU_REG (PMU_BASE, PMU_PLL_CTRL) |= PLL_2_EN | PLL_1_EN | PLL_3_MUTE;

	CPU_REG (SERIAL0_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
	CPU_REG (SERIAL1_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
#ifdef CONFIG_H7202_SERIAL23
	CPU_REG (SERIAL2_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
	CPU_REG (SERIAL3_VIRT, SERIAL_ENABLE) = SERIAL_ENABLE_EN;
	CPU_IO (GPIO_AMULSEL) = AMULSEL_USIN2 | AMULSEL_USOUT2 |
	                        AMULSEL_USIN3 | AMULSEL_USOUT3;
#endif
	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
}
开发者ID:8563,项目名称:millennium-sources,代码行数:15,代码来源:cpu-h7202.c


示例8: h7202_timerx_demux_handler

/* Although we have two interrupt lines for the timers, we only have one
 * status register which clears all pending timer interrupts on reading. So
 * we have to handle all timer interrupts in one place.
 */
static void
h7202_timerx_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
			struct pt_regs *regs)
{
	unsigned int mask, irq;

	mask = CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);

	if ( mask & TSTAT_T0INT ) {
		timer_tick(regs);
		if( mask == TSTAT_T0INT )
			return;
	}

	mask >>= 1;
	irq = IRQ_TIMER1;
	desc = irq_desc + irq;
	while (mask) {
		if (mask & 1)
			desc->handle(irq, desc, regs);
		irq++;
		desc++;
		mask >>= 1;
	}
}
开发者ID:BackupTheBerlios,项目名称:tuxap,代码行数:29,代码来源:cpu-h7202.c


示例9: h7201_timer_interrupt

/*
 * Timer interrupt handler
 */
static irqreturn_t
h7201_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
	CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);
	timer_tick(regs);
	return IRQ_HANDLED;
}
开发者ID:BackupTheBerlios,项目名称:tuxap,代码行数:10,代码来源:cpu-h7201.c


示例10: init_hw_h7202

void __init init_hw_h7202(void)
{
	/* Enable clocks */
	CPU_REG (PMU_BASE, PMU_PLL_CTRL) |= PLL_2_EN | PLL_1_EN | PLL_3_MUTE;

	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
}
开发者ID:BackupTheBerlios,项目名称:tuxap,代码行数:7,代码来源:cpu-h7202.c


示例11: h720x_gpiob_demux_handler

static void
h720x_gpiob_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
{
	unsigned int mask, irq;
	mask = CPU_REG(GPIO_B_VIRT,GPIO_STAT);
	irq = IRQ_CHAINED_GPIOB(0);
	IRQDBG("%s mask: 0x%08x irq: %d\n", __func__, mask,irq);
	h720x_gpio_handler(mask, irq, desc);
}
开发者ID:Jackeagle,项目名称:android_kernel_sony_c2305,代码行数:9,代码来源:common.c


示例12: h7201_timer_interrupt

/*
 * Timer interrupt handler
 */
static irqreturn_t
h7201_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
	write_seqlock(&xtime_lock);

	CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);
	timer_tick(regs);

	write_sequnlock(&xtime_lock);

	return IRQ_HANDLED;
}
开发者ID:Broadcom,项目名称:stblinux-2.6.18,代码行数:15,代码来源:cpu-h7201.c


示例13: h7202_init_irq

void __init h7202_init_irq (void)
{
	int 	irq;

	CPU_REG (GPIO_E_VIRT, GPIO_MASK) = 0x0;

	for (irq = IRQ_TIMER1;
	                  irq < IRQ_CHAINED_TIMERX(NR_TIMERX_IRQS); irq++) {
		mask_timerx_irq(irq);
		set_irq_chip(irq, &h7202_timerx_chip);
		set_irq_handler(irq, do_edge_IRQ);
		set_irq_flags(irq, IRQF_VALID );
	}
	set_irq_chained_handler(IRQ_TIMERX, h7202_timerx_demux_handler);

	h720x_init_irq();
}
开发者ID:BackupTheBerlios,项目名称:tuxap,代码行数:17,代码来源:cpu-h7202.c


示例14: h7202_timerx_demux_handler

/* Although we have two interrupt lines for the timers, we only have one
 * status register which clears all pending timer interrupts on reading. So
 * we have to handle all timer interrupts in one place.
 */
static void
h7202_timerx_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
{
	unsigned int mask, irq;

	mask = CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);

	if ( mask & TSTAT_T0INT ) {
		timer_tick();
		if( mask == TSTAT_T0INT )
			return;
	}

	mask >>= 1;
	irq = IRQ_TIMER1;
	while (mask) {
		if (mask & 1)
			generic_handle_irq(irq);
		irq++;
		mask >>= 1;
	}
}
开发者ID:8563,项目名称:millennium-sources,代码行数:26,代码来源:cpu-h7202.c


示例15: h720x_init_irq

void __init h720x_init_irq (void)
{
	int 	irq;

	
	CPU_REG (IRQC_VIRT, IRQC_IER) = 0x0;

	
	CPU_REG (GPIO_A_VIRT, GPIO_MASK) = 0x0;
	CPU_REG (GPIO_B_VIRT, GPIO_MASK) = 0x0;
	CPU_REG (GPIO_C_VIRT, GPIO_MASK) = 0x0;
	CPU_REG (GPIO_D_VIRT, GPIO_MASK) = 0x0;

	
	for (irq = 0; irq < NR_GLBL_IRQS; irq++) {
		irq_set_chip_and_handler(irq, &h720x_global_chip,
					 handle_level_irq);
		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
	}

	
	for (irq = IRQ_CHAINED_GPIOA(0) ; irq <= IRQ_CHAINED_GPIOD(31); irq++) {
		irq_set_chip_and_handler(irq, &h720x_gpio_chip,
					 handle_edge_irq);
		set_irq_flags(irq, IRQF_VALID );
	}
	irq_set_chained_handler(IRQ_GPIOA, h720x_gpioa_demux_handler);
	irq_set_chained_handler(IRQ_GPIOB, h720x_gpiob_demux_handler);
	irq_set_chained_handler(IRQ_GPIOC, h720x_gpioc_demux_handler);
	irq_set_chained_handler(IRQ_GPIOD, h720x_gpiod_demux_handler);

#ifdef CONFIG_CPU_H7202
	for (irq = IRQ_CHAINED_GPIOE(0) ; irq <= IRQ_CHAINED_GPIOE(31); irq++) {
		irq_set_chip_and_handler(irq, &h720x_gpio_chip,
					 handle_edge_irq);
		set_irq_flags(irq, IRQF_VALID );
	}
	irq_set_chained_handler(IRQ_GPIOE, h720x_gpioe_demux_handler);
#endif

	
	CPU_REG (IRQC_VIRT, IRQC_IER) = IRQ_ENA_MUX;
}
开发者ID:Blackburn29,项目名称:PsycoKernel,代码行数:43,代码来源:common.c


示例16: h720x_init_irq

/*
 * Initialize IRQ's, mask all, enable multiplexed irq's
 */
void __init h720x_init_irq (void)
{
	int 	irq;

	/* Mask global irq's */
	CPU_REG (IRQC_VIRT, IRQC_IER) = 0x0;

	/* Mask all multiplexed irq's */
	CPU_REG (GPIO_A_VIRT, GPIO_MASK) = 0x0;
	CPU_REG (GPIO_B_VIRT, GPIO_MASK) = 0x0;
	CPU_REG (GPIO_C_VIRT, GPIO_MASK) = 0x0;
	CPU_REG (GPIO_D_VIRT, GPIO_MASK) = 0x0;

	/* Initialize global IRQ's, fast path */
	for (irq = 0; irq < NR_GLBL_IRQS; irq++) {
		irq_set_chip_and_handler(irq, &h720x_global_chip,
					 handle_level_irq);
		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
	}

	/* Initialize multiplexed IRQ's, slow path */
	for (irq = IRQ_CHAINED_GPIOA(0) ; irq <= IRQ_CHAINED_GPIOD(31); irq++) {
		irq_set_chip_and_handler(irq, &h720x_gpio_chip,
					 handle_edge_irq);
		set_irq_flags(irq, IRQF_VALID );
	}
	irq_set_chained_handler(IRQ_GPIOA, h720x_gpioa_demux_handler);
	irq_set_chained_handler(IRQ_GPIOB, h720x_gpiob_demux_handler);
	irq_set_chained_handler(IRQ_GPIOC, h720x_gpioc_demux_handler);
	irq_set_chained_handler(IRQ_GPIOD, h720x_gpiod_demux_handler);

#ifdef CONFIG_CPU_H7202
	for (irq = IRQ_CHAINED_GPIOE(0) ; irq <= IRQ_CHAINED_GPIOE(31); irq++) {
		irq_set_chip_and_handler(irq, &h720x_gpio_chip,
					 handle_edge_irq);
		set_irq_flags(irq, IRQF_VALID );
	}
	irq_set_chained_handler(IRQ_GPIOE, h720x_gpioe_demux_handler);
#endif

	/* Enable multiplexed irq's */
	CPU_REG (IRQC_VIRT, IRQC_IER) = IRQ_ENA_MUX;
}
开发者ID:Jackeagle,项目名称:android_kernel_sony_c2305,代码行数:46,代码来源:common.c


示例17: unmask_gpio_irq

/*
 * unmask GPIO irq's
 */
static void inline unmask_gpio_irq(u32 irq)
{
	u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(irq));
	u32 bit = IRQ_TO_BIT(irq);
	CPU_REG (reg_base, GPIO_MASK) |= bit;
}
开发者ID:ForayJones,项目名称:iods,代码行数:9,代码来源:common.c


示例18: unmask_timerx_irq

/*
 * unmask multiplexed timer IRQs
 */
static void inline unmask_timerx_irq(struct irq_data *d)
{
	unsigned int bit;
	bit = 2 << ((d->irq == IRQ_TIMER64B) ? 4 : (d->irq - IRQ_TIMER1));
	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) |= bit;
}
开发者ID:8563,项目名称:millennium-sources,代码行数:9,代码来源:cpu-h7202.c


示例19: mask_timerx_irq

/*
 * mask multiplexed timer irq's
 */
static void inline mask_timerx_irq (u32 irq)
{
	unsigned int bit;
	bit = 2 << ((irq == IRQ_TIMER64B) ? 4 : (irq - IRQ_TIMER1));
	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) &= ~bit;
}
开发者ID:BackupTheBerlios,项目名称:tuxap,代码行数:9,代码来源:cpu-h7202.c


示例20: unmask_global_irq

/*
 * unmask Global irq's
 */
static void unmask_global_irq(struct irq_data *d)
{
	CPU_REG (IRQC_VIRT, IRQC_IER) |= (1 << d->irq);
}
开发者ID:Jackeagle,项目名称:android_kernel_sony_c2305,代码行数:7,代码来源:common.c



注:本文中的CPU_REG函数示例整理自Github/MSDocs等源码及文档管理平台,相关代码片段筛选自各路编程大神贡献的开源项目,源码版权归原作者所有,传播和使用请参考对应项目的License;未经允许,请勿转载。


鲜花

握手

雷人

路过

鸡蛋
该文章已有0人参与评论

请发表评论

全部评论

专题导读
上一篇:
C++ CPU_SR_ALLOC函数代码示例发布时间:2022-05-30
下一篇:
C++ CPU_PRESCALE函数代码示例发布时间:2022-05-30
热门推荐
阅读排行榜

扫描微信二维码

查看手机版网站

随时了解更新最新资讯

139-2527-9053

在线客服(服务时间 9:00~18:00)

在线QQ客服
地址:深圳市南山区西丽大学城创智工业园
电邮:jeky_zhao#qq.com
移动电话:139-2527-9053

Powered by 互联科技 X3.4© 2001-2213 极客世界.|Sitemap