C++ CLK_EnableXtalRC函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中CLK_EnableXtalRC函数的典型用法代码示例。如果您正苦于以下问题：C++ CLK_EnableXtalRC函数的具体用法？C++ CLK_EnableXtalRC怎么用？C++ CLK_EnableXtalRC使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了CLK_EnableXtalRC函数的18个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Enable Internal RC clock */
    CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);

    /* Waiting for IRC22M clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);

    /* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));

    /* Enable external 12MHz XTAL, internal 22.1184MHz */
    CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk | CLK_PWRCON_OSC22M_EN_Msk);

    /* Enable PLL and Set PLL frequency */
    CLK_SetCoreClock(PLLCON_SETTING);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_PLL_STB_Msk | CLK_CLKSTATUS_XTL12M_STB_Msk | CLK_CLKSTATUS_OSC22M_STB_Msk);

    /* Switch HCLK clock source to PLL, STCLK to HCLK/2 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL, CLK_CLKDIV_HCLK(2));

    /* Enable UART module clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Enable PWM module clock */
    CLK_EnableModuleClock(PWM01_MODULE);
    CLK_EnableModuleClock(PWM23_MODULE);

    /* Select UART module clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));

    /* Select PWM module clock source */
    CLK_SetModuleClock(PWM01_MODULE, CLK_CLKSEL1_PWM01_S_HXT, 0);
    CLK_SetModuleClock(PWM23_MODULE, CLK_CLKSEL1_PWM23_S_HXT, 0);

    /* Reset PWMA channel0~channel3 */
    SYS_ResetModule(PWM03_RST);

    /* Update System Core Clock */
    /* User can use SystemCoreClockUpdate() to calculate PllClock, SystemCoreClock and CycylesPerUs automatically. */
    //SystemCoreClockUpdate();
    PllClock        = PLL_CLOCK;            // PLL
    SystemCoreClock = PLL_CLOCK / 1;        // HCLK
    CyclesPerUs     = PLL_CLOCK / 1000000;  // For SYS_SysTickDelay()

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set P3 multi-function pins for UART0 RXD and TXD  */
    SYS->P3_MFP = SYS_MFP_P30_RXD0 | SYS_MFP_P31_TXD0;
    /* Set P2 multi-function pins for PWMA Channel0~3 */
    SYS->P2_MFP = SYS_MFP_P20_PWM0 | SYS_MFP_P21_PWM1 | SYS_MFP_P22_PWM2 | SYS_MFP_P23_PWM3;
}

开发者ID:clarenceliu，项目名称:Mplib，代码行数:59，代码来源:PWM_DeadZone.c

示例2: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Enable Internal RC 22.1184MHz clock */
    CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);

    /* Waiting for Internal RC clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);

    /* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));

    /* Enable external XTAL 12MHz clock */
    CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk);

    /* Set core clock as PLL_CLOCK from PLL */
    CLK_SetCoreClock(PLL_CLOCK);
    
    /* Enable UART module clock */
    CLK_EnableModuleClock(UART0_MODULE);    
    
    /* Select UART module clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));

    /* Enable Timer 0~3 module clock */
    CLK_EnableModuleClock(TMR0_MODULE);    
    CLK_EnableModuleClock(TMR2_MODULE);    
    CLK_EnableModuleClock(TMR3_MODULE);    

    /* Select Timer 0~3 module clock source */
    CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0_S_HXT, NULL);
    CLK_SetModuleClock(TMR2_MODULE, CLK_CLKSEL1_TMR2_S_HCLK, NULL);
    CLK_SetModuleClock(TMR3_MODULE, CLK_CLKSEL1_TMR3_S_HXT, NULL);

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PB multi-function pins for UART0 RXD, TXD */
    SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB0_Msk | SYS_GPB_MFP_PB1_Msk);
    SYS->GPB_MFP |= (SYS_GPB_MFP_PB0_UART0_RXD | SYS_GPB_MFP_PB1_UART0_TXD);

    /* Set PB multi-function pins for TM0, TM2, TM3 and TM2_EXT */
    SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB8_Msk | SYS_GPB_MFP_PB10_Msk | 
                      SYS_GPB_MFP_PB11_Msk | SYS_GPB_MFP_PB2_Msk);
    SYS->GPB_MFP |= (SYS_GPB_MFP_PB8_TM0 | SYS_GPB_MFP_PB10_TM2 | 
                     SYS_GPB_MFP_PB11_TM3 | SYS_GPB_MFP_PB2_TM2_EXT);

    SYS->ALT_MFP  &= ~( SYS_ALT_MFP_PB8_Msk | SYS_ALT_MFP_PB10_Msk | SYS_ALT_MFP_PB11_Msk |
                        SYS_ALT_MFP_PB2_Msk);
    SYS->ALT_MFP  |= (SYS_ALT_MFP_PB8_TM0 | SYS_ALT_MFP_PB10_TM2 |SYS_ALT_MFP_PB11_TM3 |
                      SYS_ALT_MFP_PB2_TM2_EXT);
    SYS->ALT_MFP2 &= ~SYS_ALT_MFP2_PB2_TM2_Msk;
    SYS->ALT_MFP2 |= SYS_ALT_MFP2_PB2_TM2_EXT;
}

开发者ID:OpenNuvoton，项目名称:NUC029xEE，代码行数:59，代码来源:main.c

示例3: SYS_Init

/**
 * Initializes the system.
 * System control registers must be unlocked.
 */
void SYS_Init() {
	// TODO: why is SYS_UnlockReg() needed? Should be already unlocked.
	SYS_UnlockReg();

	// HIRC clock (internal RC 22.1184MHz)
	CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
	CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
	
	// HCLK clock source: HIRC, HCLK source divider: 1
	CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
	
	// HXT clock (external XTAL 12MHz)
	CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
	CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
	
	// Enable 72MHz optimization
	FMC_EnableFreqOptimizeMode(FMC_FTCTL_OPTIMIZE_72MHZ);
	
	// Core clock: PLL
	CLK_SetCoreClock(PLL_CLOCK);
	CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
	
	// SPI0 clock: PCLK0
	CLK_SetModuleClock(SPI0_MODULE, CLK_CLKSEL2_SPI0SEL_PCLK0, 0);
	CLK_EnableModuleClock(SPI0_MODULE);
	
	// TMR0 clock: HXT
	CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0SEL_HXT, 0);
	CLK_EnableModuleClock(TMR0_MODULE);

	// USBD clock
	CLK_SetModuleClock(USBD_MODULE, 0, CLK_CLKDIV0_USB(3));
	CLK_EnableModuleClock(USBD_MODULE);
	
	// Enable USB 3.3V LDO
	SYS->USBPHY = SYS_USBPHY_LDO33EN_Msk;

	// EADC clock: 72Mhz / 8
	CLK_SetModuleClock(EADC_MODULE, 0, CLK_CLKDIV0_EADC(8));
	CLK_EnableModuleClock(EADC_MODULE);
	
	// Enable BOD (reset, 2.2V)
	SYS_EnableBOD(SYS_BODCTL_BOD_RST_EN, SYS_BODCTL_BODVL_2_2V);
	
	// Update system core clock
	SystemCoreClockUpdate();

	// Initialize dataflash
	Dataflash_Init();

	// Initialize I/O
	Display_SetupSPI();
	Button_Init();
	ADC_Init();

	// Initialize display
	Display_Init();
}

开发者ID:archont，项目名称:evic-sdk，代码行数:62，代码来源:init.c

示例4: SYS_Init

void SYS_Init(void)
{

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Enable HIRC clock (Internal RC 22.1184MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);

    /* Wait for HIRC clock ready */
    CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);

    /* Select HCLK clock source as HIRC and and HCLK source divider as 1 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));

    /* Set PLL to Power-down mode and PLLSTB bit in CLK_STATUS register will be cleared by hardware.*/
    CLK_DisablePLL();

    /* Enable HXT clock (external XTAL 12MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);

    /* Wait for HXT clock ready */
    CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);

    /* Set core clock as PLL_CLOCK from PLL */
    CLK_SetCoreClock(PLL_CLOCK);

    /* Enable UART module clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Select UART module clock source as HXT and UART module clock divider as 1 */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));

    /* Enable EADC module clock */
    CLK_EnableModuleClock(EADC_MODULE);

    /* EADC clock source is 72MHz, set divider to 8, ADC clock is 72/8 MHz */
    CLK_SetModuleClock(EADC_MODULE, 0, CLK_CLKDIV0_EADC(8));

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Set PD multi-function pins for UART0 RXD and TXD */
    SYS->GPD_MFPL &= ~(SYS_GPD_MFPL_PD0MFP_Msk | SYS_GPD_MFPL_PD1MFP_Msk);
    SYS->GPD_MFPL |= (SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD);

    /* Configure the GPB0 - GPB3 ADC analog input pins.  */
    SYS->GPB_MFPL &= ~(SYS_GPB_MFPL_PB0MFP_Msk | SYS_GPB_MFPL_PB1MFP_Msk |
                       SYS_GPB_MFPL_PB2MFP_Msk | SYS_GPB_MFPL_PB3MFP_Msk);
    SYS->GPB_MFPL |= (SYS_GPB_MFPL_PB0MFP_EADC_CH0 | SYS_GPB_MFPL_PB1MFP_EADC_CH1 |
                      SYS_GPB_MFPL_PB2MFP_EADC_CH2 | SYS_GPB_MFPL_PB3MFP_EADC_CH3);

    /* Disable the GPB0 - GPB3 digital input path to avoid the leakage current. */
    GPIO_DISABLE_DIGITAL_PATH(PB, 0xF);

}

开发者ID:brucetsao，项目名称:Nuvoton，代码行数:58，代码来源:main.c

示例5: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Enable External XTAL (4~24 MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
    /* Enable LIRC */
    CLK_EnableXtalRC(CLK_PWRCTL_LIRCEN_Msk);

    /* Waiting for 12MHz clock ready */
    CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);

    /* Waiting for LIRC clock stable */
    CLK_WaitClockReady( CLK_STATUS_LIRCSTB_Msk);

    /* Switch HCLK clock source to HXT */
    CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));

    /* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
    CLK->PLLCTL |= CLK_PLLCTL_PD_Msk;

    /* Set PLL frequency */
    CLK->PLLCTL = CLK_PLLCTL_84MHz_HXT;

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);

    /* Switch HCLK clock source to PLL */
    CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_PLL,CLK_CLKDIV0_HCLK(1));

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);
    CLK_EnableModuleClock(WDT_MODULE);


    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
    CLK_SetModuleClock(WDT_MODULE, CLK_CLKSEL1_WDTSEL_LIRC, 0);

    /* Update System Core Clock */
    /* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
    SystemCoreClockUpdate();


    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set GPG multi-function pins for UART0 RXD and TXD */
    SYS->GPG_MFPL = SYS_GPG_MFPL_PG1MFP_UART0_RXD | SYS_GPG_MFPL_PG2MFP_UART0_TXD ;
    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:wjw890912，项目名称:Power-measurement，代码行数:56，代码来源:main.c

示例6: SYS_Init

void SYS_Init(void)
{

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Enable HIRC clock (Internal RC 22.1184MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);

    /* Wait for HIRC clock ready */
    CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);

    /* Select HCLK clock source as HIRC and and HCLK source divider as 1 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV_HCLK(1));

    /* Set P5 multi-function pins for crystal output/input */
    SYS->P5_MFP &= ~(SYS_MFP_P50_Msk | SYS_MFP_P51_Msk);
    SYS->P5_MFP |= (SYS_MFP_P50_XT1_IN | SYS_MFP_P51_XT1_OUT);

    /* Enable HXT clock (external XTAL 12MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_XTLEN_HXT);

    /* Wait for HXT clock ready */
    CLK_WaitClockReady(CLK_STATUS_XTLSTB_Msk);

    /* Set core clock as PLL_CLOCK from PLL */
    CLK_SetCoreClock(PLL_CLOCK);

    /* Enable UART module clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Select UART module clock source as HXT and UART module clock divider as 1 */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_XTAL, CLK_CLKDIV_UART(1));

    /* Lock protected registers */
    SYS_LockReg();
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Set P0 multi-function pins for UART RXD and TXD */
    SYS->P1_MFP &= ~(SYS_MFP_P12_Msk | SYS_MFP_P13_Msk);
    SYS->P1_MFP |= (SYS_MFP_P12_UART0_RXD | SYS_MFP_P13_UART0_TXD);
    //SYS->P0_MFP &= ~(SYS_MFP_P01_Msk | SYS_MFP_P00_Msk);
    //SYS->P0_MFP |= (SYS_MFP_P01_UART0_RXD | SYS_MFP_P00_UART0_TXD);

    /* Set P3 multi-function pins for Clock Output */
    SYS->P3_MFP = SYS_MFP_P36_CLKO;
}

开发者ID:OpenNuvoton，项目名称:Mini58BSP，代码行数:52，代码来源:main.c

示例7: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Enable Internal RC 22.1184MHz clock */
    CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);

    /* Waiting for Internal RC clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);

    /* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));

    /* Enable external XTAL 12MHz clock */
    CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk);

    /* Waiting for external XTAL clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk);

    /* Set core clock as PLL_CLOCK from PLL */
    CLK_SetCoreClock(PLL_CLOCK);

    /* Enable UART0 and UART1 module clock */
    CLK_EnableModuleClock(UART0_MODULE);
    CLK_EnableModuleClock(UART1_MODULE);

    CLK_EnableModuleClock(TMR0_MODULE);

    /* Select UART0 and UART1 module clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
    CLK_SetModuleClock(UART1_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));

    CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0_S_HXT, 0);	

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Set P3 multi-function pins for UART0 RXD and TXD */
    SYS->P3_MFP &= ~(SYS_MFP_P30_Msk | SYS_MFP_P31_Msk);
    SYS->P3_MFP |= (SYS_MFP_P30_RXD0 | SYS_MFP_P31_TXD0);
		
		/* Set P0 multi-function pins for UART1 RXD and TXD */
    SYS->P0_MFP &= ~(SYS_MFP_P00_Msk | SYS_MFP_P01_Msk);
    SYS->P0_MFP |= (SYS_MFP_P00_TXD1 | SYS_MFP_P01_RXD1);
}

开发者ID:YanMinge，项目名称:Neuron，代码行数:48，代码来源:sysinit.c

示例8: setupSystemClock

void setupSystemClock()
{
	SYS_UnlockReg();
  /*---------------------------------------------------------------------------------------------------------*/
  /* Init System Clock                                                                                       */
  /*---------------------------------------------------------------------------------------------------------*/
	/* Enable HIRC clock */
	CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);

	/* Waiting for HIRC clock ready */
	CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);

	/* Switch HCLK clock source to HIRC */
	CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));

	/* Enable external XTAL 12MHz clock */
	//CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);

	/* Waiting for external XTAL clock ready */
	//CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);

	/* Set core clock as PLL_CLOCK from PLL and SysTick source to HCLK/2*/
	CLK_SetCoreClock(SYSTEM_CLOCK);
	CLK_SetSysTickClockSrc(CLK_CLKSEL0_STCLKSEL_HCLK_DIV2);

	/* Waiting for PLL clock ready */
	CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);

	SYS_LockReg();
}

开发者ID:JohnsonShen，项目名称:NuBrick，代码行数:30，代码来源:main.c

示例9: clock_init

/**
 * This function will initial Clock tree.
 */
static void clock_init(void)
{
    /* Unlock protected registers */
    SYS_UnlockReg();

    SystemInit();

    /* Set XT1_OUT(PF.2) and XT1_IN(PF.3) to input mode */
    PF->MODE &= ~(GPIO_MODE_MODE2_Msk | GPIO_MODE_MODE3_Msk);

    /* Enable External XTAL (4~24 MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);

    /* Waiting for 12MHz clock ready */
    CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);

    /* Switch HCLK clock source to HXT */
    CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));

    /* Set core clock as PLL_CLOCK from PLL */
    CLK_SetCoreClock(FREQ_192MHZ);

    /* Set both PCLK0 and PCLK1 as HCLK/4 */
    CLK->PCLKDIV = CLK_PCLKDIV_PCLK0DIV4 | CLK_PCLKDIV_PCLK1DIV4;

    SystemCoreClockUpdate();

    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:heyuanjie87，项目名称:rt-thread，代码行数:33，代码来源:board.c

示例10: SYS_Init

/*---------------------------------------------------------------------------------------------------------*/
void SYS_Init(void)
{
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Set HCLK source form HXT and HCLK source divide 1  */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));

    /* Enable external 12MHz HXT, 32KHz LXT and HIRC */
    CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);

    /*  Set HCLK frequency 12MHz */
    CLK_SetCoreClock(12000000);

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HIRC,CLK_UART_CLK_DIVIDER(1));

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PA multi-function pins for UART0 RXD and TXD */
    SYS->PA_H_MFP &= ~( SYS_PA_H_MFP_PA15_MFP_Msk | SYS_PA_H_MFP_PA14_MFP_Msk);
    SYS->PA_H_MFP |= (SYS_PA_H_MFP_PA15_MFP_UART0_TX|SYS_PA_H_MFP_PA14_MFP_UART0_RX);

    /* Set PB multi-function pins for Clock Output */
    SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) |  SYS_PB_H_MFP_PB12_MFP_CKO;
    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:OpenNuvoton，项目名称:Nano100B_BSP，代码行数:33，代码来源:main.c

示例11: SysInit

/*---------------------------------------------------------------------------------------------------------*/
void SysInit(void)
{
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Set HCLK source form HXT and HCLK source divide 1  */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));

    /* Enable external 12MHz HXT, 32KHz LXT and HIRC */
    CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);

#if 1
    SYS->PB_H_MFP &= ~( SYS_PB_H_MFP_PB14_MFP_Msk | SYS_PB_H_MFP_PB13_MFP_Msk);
    SYS->PB_H_MFP |= (SYS_PB_H_MFP_PB14_MFP_UART0_TX | SYS_PB_H_MFP_PB13_MFP_UART0_RX );
    UART0->BAUD = 0x67;              /* Baud Rate:115200  OSC:12MHz */
    //UART0->BAUD = 0x60;            /* Baud Rate:115200  OSC:11.0592 MHz */
    UART0->TLCTL = (UART0->TLCTL & ~0x3) | 0x3; /* character len is 8 bits */
    UART0->TLCTL |= (1<<2);
#endif

    /*  Set HCLK frequency 32MHz */
    CLK_SetCoreClock(32000000);

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Enable PWM clock */
    CLK_EnableModuleClock(PWM0_CH01_MODULE);
    CLK_EnableModuleClock(PWM0_CH23_MODULE);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HIRC,CLK_UART_CLK_DIVIDER(1));

    /* Set HCLK as PWM clock source */
    CLK_SetModuleClock(PWM0_CH01_MODULE, CLK_CLKSEL1_PWM0_CH01_S_HCLK, 0);
    CLK_SetModuleClock(PWM0_CH23_MODULE, CLK_CLKSEL1_PWM0_CH23_S_HCLK, 0);

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PA multi-function pins for UART0 RXD and TXD */
    SYS->PB_L_MFP &= ~( SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
    SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX );

    /* Set PB multi-function pins for Clock Output */
    SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) |  SYS_PB_H_MFP_PB12_MFP_CKO0;

    /* Set PB and PE multi-function pins for PWM */
    SYS->PB_H_MFP = (SYS->PB_H_MFP & ~(SYS_PB_H_MFP_PB8_MFP_Msk | SYS_PB_H_MFP_PB9_MFP_Msk)) | SYS_PB_H_MFP_PB8_MFP_PWM0_CH0 | SYS_PB_H_MFP_PB9_MFP_PWM0_CH1;
    SYS->PE_H_MFP = (SYS->PE_H_MFP & ~(SYS_PE_H_MFP_PE8_MFP_Msk | SYS_PE_H_MFP_PE9_MFP_Msk)) | SYS_PE_H_MFP_PE8_MFP_PWM0_CH2 | SYS_PE_H_MFP_PE9_MFP_PWM0_CH3;

    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:clarenceliu，项目名称:Mplib，代码行数:58，代码来源:PWM_DeadZone.c

示例12: SysInit

/*---------------------------------------------------------------------------------------------------------*/
void SysInit(void)
{
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Set HCLK source form HXT and HCLK source divide 1  */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));

    /* Enable external 12MHz HXT, 32KHz LXT and HIRC */
    CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);

#if 1
    SYS->PB_H_MFP &= ~( SYS_PB_H_MFP_PB14_MFP_Msk | SYS_PB_H_MFP_PB13_MFP_Msk);
    SYS->PB_H_MFP |= (SYS_PB_H_MFP_PB14_MFP_UART0_TX | SYS_PB_H_MFP_PB13_MFP_UART0_RX );
    UART0->BAUD = 0x67;              /* Baud Rate:115200  OSC:12MHz */
    //UART0->BAUD = 0x60;            /* Baud Rate:115200  OSC:11.0592 MHz */
    UART0->TLCTL = (UART0->TLCTL & ~0x3) | 0x3; /* character len is 8 bits */
    UART0->TLCTL |= (1<<2);
#endif

    /*  Set HCLK frequency 32MHz */
    CLK_SetCoreClock(32000000);

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HIRC,CLK_UART_CLK_DIVIDER(1));

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PA multi-function pins for UART0 RXD and TXD */
    SYS->PB_L_MFP &= ~( SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
    SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX );

    /* Set PB multi-function pins for Clock Output */
    SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) |  SYS_PB_H_MFP_PB12_MFP_CKO0;

    /* Set PA multi-function pins for ADC */
    SYS->PA_L_MFP &= ~(SYS_PA_L_MFP_PA0_MFP_Msk | SYS_PA_L_MFP_PA1_MFP_Msk | SYS_PA_L_MFP_PA2_MFP_Msk);
    SYS->PA_L_MFP |= SYS_PA_L_MFP_PA0_MFP_ADC_CH0 | SYS_PA_L_MFP_PA1_MFP_ADC_CH1 | SYS_PA_L_MFP_PA2_MFP_ADC_CH2;

    /* Disable digital input path */
    PA->OFFD = PA->OFFD | ((ADC_CH_0_MASK | ADC_CH_1_MASK | ADC_CH_2_MASK)<< 16);

    /* Enable ADC clock */
    CLK_EnableModuleClock(ADC_MODULE);

    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:clarenceliu，项目名称:Mplib，代码行数:56，代码来源:ADC_ContinuousScan.c

示例13: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Enable External XTAL (4~24 MHz) */
    CLK_EnableXtalRC(CLK_PWRCON_HXT_EN_Msk);

    /* Waiting for 12MHz clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk);

    /* Switch HCLK clock source to HXT */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_CLKDIV0_HCLK(1));

    /* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
    CLK->PLLCON |= CLK_PLLCON_PD_Msk;

    /* Set PLL frequency */
    CLK->PLLCON = PLLCON_SETTING;

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_PLL_STB_Msk);

    /* Switch HCLK clock source to PLL */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL,CLK_CLKDIV0_HCLK(1));

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);
    CLK_EnableModuleClock(PDMA_MODULE);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HXT,CLK_CLKDIV0_UART(1));

    /* Update System Core Clock */
    /* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
    SystemCoreClockUpdate();

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set GPG multi-function pins for UART0 RXD and TXD */
    SYS->GPG_MFPL &= ~(SYS_GPG_MFPL_PG1_MFP_Msk|SYS_GPG_MFPL_PG2_MFP_Msk);
    SYS->GPG_MFPL |= SYS_GPG_MFPL_PG1_MFP_UART0_RXD | SYS_GPG_MFPL_PG2_MFP_UART0_TXD ;

    /* Set GPG multi-function pins for CKO */
    SYS->GPC_MFPL = (SYS->GPC_MFPL & ~SYS_GPC_MFPL_PC5_MFP_Msk) | SYS_GPC_MFPL_PC5_MFP_CLK_O ;

    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:clarenceliu，项目名称:Mplib，代码行数:53，代码来源:PDMA_Example.c

示例14: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Enable Internal RC 22.1184MHz clock */
    CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);

    /* Waiting for Internal RC clock ready */
    CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);

    /* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
    CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));

    /* Enable external XTAL 12MHz clock */
    CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);

    /* Waiting for external XTAL clock ready */
    CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);

    /* Set core clock as PLL_CLOCK from PLL */
    CLK_SetCoreClock(PLL_CLOCK);

    /* Enable UART module clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Select UART module clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));


    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/

    /* Set PD multi-function pins for UART0 RXD and TXD */
    SYS->GPD_MFPL &= ~(SYS_GPD_MFPL_PD0MFP_Msk | SYS_GPD_MFPL_PD1MFP_Msk);
    SYS->GPD_MFPL |= (SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD);

}

开发者ID:brucetsao，项目名称:Nuvoton，代码行数:40，代码来源:ldrom_main.c

示例15: SYS_Init

void SYS_Init(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Enable HIRC clock */
    CLK_EnableXtalRC(CLK_PWRCON_IRC22M_EN_Msk);

    /* Waiting for HIRC clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_IRC22M_STB_Msk);

    /* Switch HCLK clock source to HIRC */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));

    /* Enable HXT and LIRC */
    CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk | CLK_PWRCON_IRC10K_EN_Msk);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk | CLK_CLKSTATUS_IRC10K_STB_Msk);

    /* Set core clock as PLL_CLOCK from PLL and SysTick source to HCLK/2*/
    CLK_SetCoreClock(PLL_CLOCK);
    CLK_SetSysTickClockSrc(CLK_CLKSEL0_STCLK_S_HCLK_DIV2);

    /* Enable peripheral clock */
    CLK_EnableModuleClock(UART0_MODULE);
    CLK_EnableModuleClock(WDT_MODULE);

    /* Peripheral clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_PLL, CLK_CLKDIV_UART(1));
    CLK_SetModuleClock(WDT_MODULE, CLK_CLKSEL1_WDT_S_LIRC, 0);

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PB multi-function pins for UART0 RXD, TXD */
    SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB0_Msk | SYS_GPB_MFP_PB1_Msk);
    SYS->GPB_MFP |= (SYS_GPB_MFP_PB0_UART0_RXD | SYS_GPB_MFP_PB1_UART0_TXD);
}

开发者ID:OpenNuvoton，项目名称:NUC029xDE，代码行数:39，代码来源:main.c

示例16: SYS_Init

/*---------------------------------------------------------------------------------------------------------*/
void SYS_Init(void)
{
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Set HCLK source form HXT and HCLK source divide 1  */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));

    /* Enable external 12MHz HXT, 32KHz LXT and HIRC */
    CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);

    /*  Set HCLK frequency 32MHz */
    CLK_SetCoreClock(32000000);

    CLK->AHBCLK |= CLK_AHBCLK_DMA_EN_Msk;

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);

    /* Enable ADC clock */
    CLK_EnableModuleClock(ADC_MODULE);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HXT,CLK_UART_CLK_DIVIDER(1));

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PA multi-function pins for UART0 RXD and TXD */
    SYS->PB_L_MFP &= ~( SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
    SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_RX | SYS_PB_L_MFP_PB1_MFP_UART0_TX );

    /* Set PB multi-function pins for Clock Output */
    SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) |  SYS_PB_H_MFP_PB12_MFP_CKO;

    /* Set PA.0,PA.1,PA.2,PA.3 multi-function pin for ADC channel 0,1,2,3 */
    SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA0_MFP_Msk) | SYS_PA_L_MFP_PA0_MFP_ADC_CH0;
    SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA1_MFP_Msk) | SYS_PA_L_MFP_PA1_MFP_ADC_CH1;
    SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA2_MFP_Msk) | SYS_PA_L_MFP_PA2_MFP_ADC_CH2;
    SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA3_MFP_Msk) | SYS_PA_L_MFP_PA3_MFP_ADC_CH3;

    /* Disable PA.0 digital input path */
    PA->OFFD |= ((1 << 0) << GP_OFFD_OFFD_Pos);

    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:OpenNuvoton，项目名称:Nano100A_BSP，代码行数:51，代码来源:main.c

示例17: SysInit

void SysInit(void)
{

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Enable External XTAL (4~24 MHz) */
    CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk);

    /* Waiting for 12MHz clock ready */
    CLK_WaitClockReady( CLK_CLKSTATUS_HXT_STB_Msk);

    /* Switch HCLK clock source to HXT */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);
    CLK_EnableModuleClock(TMR0_MODULE);
    CLK_EnableModuleClock(TMR1_MODULE);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_UART_CLK_DIVIDER(1));
    CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0_S_HXT, CLK_TMR0_CLK_DIVIDER(1));
    CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR1_S_HXT, CLK_TMR1_CLK_DIVIDER(1));

    /* Update System Core Clock */
    /* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
    SystemCoreClockUpdate();


    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set GPB multi-function pins for UART0 RXD and TXD */
    SYS->PB_L_MFP &= ~(SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
    SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX);

    /* Set Timer0 event counting/toggle out pin */
    SYS->PB_H_MFP &= ~SYS_PB_H_MFP_PB8_MFP_Msk;
    SYS->PB_H_MFP |= SYS_PB_H_MFP_PB8_MFP_TMR0_EXT;

    /* Lock protected registers */
    SYS_LockReg();

}

开发者ID:clarenceliu，项目名称:Mplib，代码行数:48，代码来源:Timer_InterTimerTriggerMode.c

示例18: SysInit

void SysInit(void)
{
    /*---------------------------------------------------------------------------------------------------------*/
    /* Init System Clock                                                                                       */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Unlock protected registers */
    SYS_UnlockReg();

    /* Set HCLK source form HXT and HCLK source divide 1  */
    CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));

    /* Enable external 12MHz HXT, 32KHz LXT and HIRC */
    CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);

    /* Waiting for clock ready */
    CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);

    /*  Set HCLK frequency 32MHz */
    CLK_SetCoreClock(32000000);

    /* Select IP clock source */
    CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HIRC, CLK_UART_CLK_DIVIDER(1));
    CLK_SetModuleClock(I2C0_MODULE, 0, 0);
    CLK_SetModuleClock(I2C1_MODULE, 0, 0);

    /* Enable IP clock */
    CLK_EnableModuleClock(UART0_MODULE);
    CLK_EnableModuleClock(I2C0_MODULE);
    CLK_EnableModuleClock(I2C1_MODULE);

    /* Update System Core Clock */
    /* User can use SystemCoreClockUpdate() to calculate PllClock, SystemCoreClock and CycylesPerUs automatically. */
    SystemCoreClockUpdate();

    /*---------------------------------------------------------------------------------------------------------*/
    /* Init I/O Multi-function                                                                                 */
    /*---------------------------------------------------------------------------------------------------------*/
    /* Set PB multi-function pins for UART0 RXD and TXD  */
    SYS->PB_L_MFP &= ~(SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
    SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX);

    /* Set multi function pin for I2C0/I2C1 */
    SYS->PC_L_MFP = (SYS_PC_L_MFP_PC0_MFP_I2C0_SCL | SYS_PC_L_MFP_PC1_MFP_I2C0_SDA | SYS_PC_L_MFP_PC2_MFP_I2C1_SCL | SYS_PC_L_MFP_PC3_MFP_I2C1_SDA);

    /* Lock protected registers */
    SYS_LockReg();
}

开发者ID:clarenceliu，项目名称:Mplib，代码行数:47，代码来源:I2C_Loopback.c

注：本文中的CLK_EnableXtalRC函数示例整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ CLK_PeripheralClockConfig函数代码示例发布时间：2022-05-30

C++ CLK_EnableModuleClock函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19154|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9979|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8320|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8690|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8631|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9647|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8615|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7994|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8646|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7530|2022-11-06

客服电话

电子邮件

C++ CLK_EnableXtalRC函数代码示例

示例1: SYS_Init

示例2: SYS_Init

示例3: SYS_Init

示例4: SYS_Init

示例5: SYS_Init

示例6: SYS_Init

示例7: SYS_Init

示例8: setupSystemClock

示例9: clock_init

示例10: SYS_Init

示例11: SysInit

示例12: SysInit

示例13: SYS_Init

示例14: SYS_Init

示例15: SYS_Init

示例16: SYS_Init

示例17: SysInit

示例18: SysInit

请发表评论

全部评论

上一篇：

下一篇：

dphi-official/Machine_Learning_Bootcamp

juven/maven-bash-completion: Maven Bash

win7系统注册表编辑器打开的操作方法

route101/mastoinker: Quick image view as

openshift/library-go: Helpers for going

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053