C++ sdio_claim_host函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中sdio_claim_host函数的典型用法代码示例。如果您正苦于以下问题：C++ sdio_claim_host函数的具体用法？C++ sdio_claim_host怎么用？C++ sdio_claim_host使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了sdio_claim_host函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: disable_sdio_interrupt

void disable_sdio_interrupt(void){

#ifndef ATWILC_SDIO_IRQ_GPIO
	int ret;

	if(sdio_intr_lock  == ATWILC_SDIO_HOST_IRQ_TAKEN ) 
		wait_event_interruptible(sdio_intr_waitqueue, sdio_intr_lock == ATWILC_SDIO_HOST_NO_TAKEN );
	sdio_intr_lock  = ATWILC_SDIO_HOST_DIS_TAKEN;

	sdio_claim_host(local_sdio_func);
	ret = sdio_release_irq(local_sdio_func);
	if (ret < 0) {
			PRINT_ER("can't release sdio_irq, err(%d)\n", ret);
		}
	sdio_release_host(local_sdio_func);
	
	sdio_intr_lock  = ATWILC_SDIO_HOST_NO_TAKEN;
#endif
}

开发者ID:globalgang，项目名称:driver，代码行数:19，代码来源:linux_wlan_sdio.c

示例2: woal_sdio_read_write_cmd52

/** 
 *  @brief This function updates card reg based on the Cmd52 value in dev structure
 *  
 *  @param priv    	A pointer to moal_handle structure
 *  @param func    	A pointer to store func variable
 *  @param reg    	A pointer to store reg variable
 *  @param val    	A pointer to store val variable
 *  @return 	   	MLAN_STATUS_SUCCESS or MLAN_STATUS_FAILURE
 */
int
woal_sdio_read_write_cmd52(moal_handle * handle, int func, int reg, int val)
{
    int ret = MLAN_STATUS_SUCCESS;
    struct sdio_mmc_card *card = (struct sdio_mmc_card *) handle->card;

    ENTER();
    /* Save current func and reg for read */
    handle->cmd52_func = func;
    handle->cmd52_reg = reg;
    sdio_claim_host(card->func);
    if (val >= 0) {
        /* Perform actual write only if val is provided */
        if (func)
            sdio_writeb(card->func, val, reg, &ret);
        else
            sdio_f0_writeb(card->func, val, reg, &ret);
        if (ret) {
            PRINTM(MERROR, "Cannot write value (0x%x) to func %d reg 0x%x\n",
                   val, func, reg);
        } else {
            PRINTM(MMSG, "write value (0x%x) to func %d reg 0x%x\n", (u8) val,
                   func, reg);
            handle->cmd52_val = val;
        }
    } else {
        if (func)
            val = sdio_readb(card->func, reg, &ret);
        else
            val = sdio_f0_readb(card->func, reg, &ret);
        if (ret) {
            PRINTM(MERROR, "Cannot read value from func %d reg 0x%x\n", func,
                   reg);
        } else {
            PRINTM(MMSG, "read value (0x%x) from func %d reg 0x%x\n", (u8) val,
                   func, reg);
            handle->cmd52_val = val;
        }
    }
    sdio_release_host(card->func);
    LEAVE();
    return ret;
}

开发者ID:CoreTech-Development，项目名称:buildroot-linux-kernel-m3，代码行数:52，代码来源:moal_sdio_mmc.c

示例3: woal_register_dev

/** 
 *  @brief This function registers the device
 *  
 *  @param handle  A pointer to moal_handle structure
 *  @return 	   MLAN_STATUS_SUCCESS or MLAN_STATUS_FAILURE
 */
mlan_status
woal_register_dev(moal_handle * handle)
{
    int ret = MLAN_STATUS_SUCCESS;
    struct sdio_mmc_card *card = handle->card;
    struct sdio_func *func;

    ENTER();

    func = card->func;
    sdio_claim_host(func);
    /* Request the SDIO IRQ */
    ret = sdio_claim_irq(func, woal_sdio_interrupt);
    if (ret) {
        PRINTM(MFATAL, "sdio_claim_irq failed: ret=%d\n", ret);
        goto release_host;
    }

    /* Set block size */
    ret = sdio_set_block_size(card->func, MLAN_SDIO_BLOCK_SIZE);
    if (ret) {
        PRINTM(MERROR, "sdio_set_block_seize(): cannot set SDIO block size\n");
        ret = MLAN_STATUS_FAILURE;
        goto release_irq;
    }

    sdio_release_host(func);
    sdio_set_drvdata(func, card);

    handle->hotplug_device = &func->dev;

    LEAVE();
    return MLAN_STATUS_SUCCESS;

  release_irq:
    sdio_release_irq(func);
  release_host:
    sdio_release_host(func);
    handle->card = NULL;

    LEAVE();
    return MLAN_STATUS_FAILURE;
}

开发者ID:CoreTech-Development，项目名称:buildroot-linux-kernel-m3，代码行数:49，代码来源:moal_sdio_mmc.c

示例4: if_sdio_send_chunk

static int if_sdio_send_chunk(struct iwm_priv *iwm, u8 *buf, int count)
{
	struct iwm_sdio_priv *hw = iwm_to_if_sdio(iwm);
	int aligned_count = ALIGN(count, hw->blk_size);
	int ret;

	if ((unsigned long)buf & 0x3) {
		IWM_ERR(iwm, "buf <%p> is not dword aligned\n", buf);
		
		return -EINVAL;
	}

	sdio_claim_host(hw->func);
	ret = sdio_memcpy_toio(hw->func, IWM_SDIO_DATA_ADDR, buf,
			       aligned_count);
	sdio_release_host(hw->func);

	return ret;
}

开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:19，代码来源:sdio.c

示例5: woal_unregister_dev

/**
 *  @brief This function de-registers the device
 *
 *  @param handle A pointer to moal_handle structure
 *  @return         N/A
 */
void
woal_unregister_dev(moal_handle * handle)
{
	ENTER();
	if (handle->card) {
		/* Release the SDIO IRQ */
		sdio_claim_host(((struct sdio_mmc_card *)handle->card)->func);
		sdio_release_irq(((struct sdio_mmc_card *)handle->card)->func);
		sdio_disable_func(((struct sdio_mmc_card *)handle->card)->func);
		sdio_release_host(((struct sdio_mmc_card *)handle->card)->func);

		sdio_set_drvdata(((struct sdio_mmc_card *)handle->card)->func,
				 NULL);

		PRINTM(MWARN, "Making the sdio dev card as NULL\n");
	}

	LEAVE();
}

开发者ID:GalaxyTab4，项目名称:maxicm_kernel_samsung_degaswifi，代码行数:25，代码来源:moal_sdio_mmc.c

示例6: sd_f0_read8

u8 sd_f0_read8(PSDIO_DATA psdio, u32 addr, s32 *err)
{
	u8 v;
	struct sdio_func *func;

_func_enter_;

	func = psdio->func;

	sdio_claim_host(func);
	v = sdio_f0_readb(func, addr, err);
	sdio_release_host(func);
	if (err && *err)
		printk(KERN_ERR "%s: FAIL!(%d) addr=0x%05x\n", __func__, *err, addr);

_func_exit_;

	return v;
}

开发者ID:Audioniek，项目名称:driver，代码行数:19，代码来源:sdio_ops_linux.c

示例7: smssdio_sendrequest

static int smssdio_sendrequest(void *context, void *buffer, size_t size)
{
	int ret = 0;
	struct smssdio_device *smsdev;
	void* auxbuf = NULL;

	smsdev = context;
	
	if (size & 3)
	{
		/* Make sure size is aligned to 32 bits, round up if required*/			
		auxbuf = kmalloc((size + 3) & 0xfffffffc, GFP_KERNEL);
		memcpy (auxbuf, buffer, size);
		buffer = auxbuf;
		size = (size + 3) & 0xfffffffc;
	}


	sdio_claim_host(smsdev->func);

	while (size >= smsdev->func->cur_blksize) {
		ret = sdio_memcpy_toio(smsdev->func, SMSSDIO_DATA,
					buffer, smsdev->func->cur_blksize);
		if (ret)
			goto out;

		buffer += smsdev->func->cur_blksize;
		size -= smsdev->func->cur_blksize;
	}

	if (size) {
		ret = sdio_memcpy_toio(smsdev->func, SMSSDIO_DATA,
					buffer, size);
	}

out:
	if (auxbuf)
		kfree(auxbuf);
	sdio_release_host(smsdev->func);

	return ret;
}

开发者ID:apc-io，项目名称:apc-rock-II，代码行数:42，代码来源:smssdio.c

示例8: mwifiex_register_dev

/*
 * This function registers the SDIO device.
 *
 * SDIO IRQ is claimed, block size is set and driver data is initialized.
 */
static int mwifiex_register_dev(struct mwifiex_adapter *adapter)
{
	int ret = 0;
	struct sdio_mmc_card *card = adapter->card;
	struct sdio_func *func = card->func;

	/* save adapter pointer in card */
	card->adapter = adapter;

	sdio_claim_host(func);

	/* Request the SDIO IRQ */
	ret = sdio_claim_irq(func, mwifiex_sdio_interrupt);
	if (ret) {
		pr_err("claim irq failed: ret=%d\n", ret);
		goto disable_func;
	}

	/* Set block size */
	ret = sdio_set_block_size(card->func, MWIFIEX_SDIO_BLOCK_SIZE);
	if (ret) {
		pr_err("cannot set SDIO block size\n");
		ret = -1;
		goto release_irq;
	}

	sdio_release_host(func);
	sdio_set_drvdata(func, card);

	adapter->dev = &func->dev;

	return 0;

release_irq:
	sdio_release_irq(func);
disable_func:
	sdio_disable_func(func);
	sdio_release_host(func);
	adapter->card = NULL;

	return -1;
}

开发者ID:ARMP，项目名称:ARMP-i9300，代码行数:47，代码来源:sdio.c

示例9: woal_read_data_sync

/**
 *  @brief This function reads multiple bytes from card memory
 *
 *  @param handle   A Pointer to the moal_handle structure
 *  @param pmbuf    Pointer to mlan_buffer structure
 *  @param port     Port
 *  @param timeout  Time out value
 *
 *  @return         MLAN_STATUS_SUCCESS or MLAN_STATUS_FAILURE
 */
mlan_status
woal_read_data_sync(moal_handle *handle, mlan_buffer *pmbuf, t_u32 port,
		    t_u32 timeout)
{
	mlan_status ret = MLAN_STATUS_FAILURE;
	t_u8 *buffer = (t_u8 *)(pmbuf->pbuf + pmbuf->data_offset);
	t_u8 blkmode =
		(port & MLAN_SDIO_BYTE_MODE_MASK) ? BYTE_MODE : BLOCK_MODE;
	t_u32 blksz = (blkmode == BLOCK_MODE) ? MLAN_SDIO_BLOCK_SIZE : 1;
	t_u32 blkcnt =
		(blkmode ==
		 BLOCK_MODE) ? (pmbuf->data_len /
				MLAN_SDIO_BLOCK_SIZE) : pmbuf->data_len;
	t_u32 ioport = (port & MLAN_SDIO_IO_PORT_MASK);
	int status = 0;
	if (pmbuf->use_count > 1)
		return woal_sdio_rw_mb(handle, pmbuf, port, MFALSE);
#ifdef SDIO_MMC_DEBUG
	handle->cmd53r = 1;
#endif
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 32)
	sdio_claim_host(((struct sdio_mmc_card *)handle->card)->func);
#endif
	status = sdio_readsb(((struct sdio_mmc_card *)handle->card)->func,
			     buffer, ioport, blkcnt * blksz);
	if (!status) {
		ret = MLAN_STATUS_SUCCESS;
	} else {
		PRINTM(MERROR, "cmd53 read error=%d\n", status);
#if LINUX_VERSION_CODE >= KERNEL_VERSION(3, 0, 0)
        /* issue abort cmd52 command through F0*/
        sdio_f0_writeb(((struct sdio_mmc_card *)handle->card)->func, 0x01, SDIO_CCCR_ABORT, &status);
#endif
	}
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 32)
	sdio_release_host(((struct sdio_mmc_card *)handle->card)->func);
#endif
#ifdef SDIO_MMC_DEBUG
	handle->cmd53r = 2;
#endif
	return ret;
}

开发者ID:krysanto，项目名称:steamlink-sdk，代码行数:52，代码来源:moal_sdio_mmc.c

示例10: mtk_sdio_remove

static void mtk_sdio_remove(struct sdio_func *func)
{
	/* printk(KERN_INFO DRV_NAME"mtk_sdio_remove()\n"); */

#if CFG_DBG_GPIO_PINS
	/* printk(KERN_INFO "[%s] deinit debug gpio\n", __FUNCTION__); */
	debug_gpio_deinit();
#endif

	ASSERT(func);
	/* printk(KERN_INFO DRV_NAME"pfWlanRemove done\n"); */
	pfWlanRemove();

	sdio_claim_host(func);
	sdio_disable_func(func);
	/* printk(KERN_INFO DRV_NAME"sdio_disable_func() done\n"); */
	sdio_release_host(func);

	/* printk(KERN_INFO DRV_NAME"mtk_sdio_remove() done\n"); */
}

开发者ID:Swapnil133609，项目名称:Zeus_exp，代码行数:20，代码来源:sdio.c

示例11: sbi_enable_host_int

/** 
 *  @brief This function enables the host interrupts.
 *  
 *  @param priv    A pointer to bt_private structure
 *  @return 	   BT_STATUS_SUCCESS or BT_STATUS_FAILURE
 */
int
sbi_enable_host_int(bt_private * priv)
{
    struct sdio_mmc_card *card = priv->bt_dev.card;
    int ret;

    ENTER();

    if (!card || !card->func) {
        LEAVE();
        return BT_STATUS_FAILURE;
    }
    sdio_claim_host(card->func);
    ret = sd_enable_host_int_mask(priv, HIM_ENABLE);
    sd_get_rx_unit(priv);
    sdio_release_host(card->func);

    LEAVE();
    return ret;
}

开发者ID:12019，项目名称:miniature-octo-tribble，代码行数:26，代码来源:bt_sdiommc.c

示例12: sd_f0_write8

void sd_f0_write8(PSDIO_DATA psdio, u32 addr, u8 v, s32 *err)
{
	struct sdio_func *func;
	bool claim_needed;

_func_enter_;

	func = psdio->func;
	claim_needed = rtw_sdio_claim_host_needed(func);

	if (claim_needed)
		sdio_claim_host(func);
	sdio_f0_writeb(func, v, addr, err);
	if (claim_needed)
		sdio_release_host(func);
	if (err && *err)
		DBG_871X(KERN_ERR "%s: FAIL!(%d) addr=0x%05x val=0x%02x\n", __func__, *err, addr, v);

_func_exit_;
}

开发者ID:takitr，项目名称:linux-wetek-3.10.y-1，代码行数:20，代码来源:sdio_ops_linux.c

示例13: mtlte_sys_sdio_remove_irq

static int mtlte_sys_sdio_remove_irq(struct sdio_func *sdiofunc)
{
	int ret = 0 ;

	KAL_RAWPRINT(("[REMOVE] =======> mtlte_sys_sdio_remove_irq\n")); 

    lte_sdio_disable_eirq();
    
	sdio_claim_host(sdiofunc);
    ret = sdio_release_irq(sdiofunc);
    sdio_release_host(sdiofunc);

    if (ret){
        KAL_RAWPRINT(("[REMOVE] XXXXXX mtlte_sys_sdio_remove_irq fail, %d \n", ret )); 
        return (ret);
    }

    KAL_RAWPRINT(("[REMOVE] <======= mtlte_sys_sdio_remove_irq\n")); 
    return 0 ;
}

开发者ID:Scorpio92，项目名称:mediatek，代码行数:20，代码来源:lte_main.c

示例14: sif_enable_irq

void sif_enable_irq(struct esp_pub *epub) 
{
        int err;
        struct esp_sdio_ctrl *sctrl = NULL;

        sctrl = (struct esp_sdio_ctrl *)epub->sif;

        sdio_claim_host(sctrl->func);

        err = sdio_claim_irq(sctrl->func, sif_dsr);

        if (err)
                esp_dbg(ESP_DBG_ERROR, "sif %s failed\n", __func__);

        atomic_set(&epub->sip->state, SIP_BOOT);

        atomic_set(&sctrl->irq_installed, 1);

        sdio_release_host(sctrl->func);
}

开发者ID:Icenowy，项目名称:esp8089，代码行数:20，代码来源:sdio_sif_esp.c

示例15: if_sdio_enable

/* Bus ops */
static int if_sdio_enable(struct iwm_priv *iwm)
{
	struct iwm_sdio_priv *hw = iwm_to_if_sdio(iwm);
	int ret;

	sdio_claim_host(hw->func);

	ret = sdio_enable_func(hw->func);
	if (ret) {
		IWM_ERR(iwm, "Couldn't enable the device: is TOP driver "
			"loaded and functional?\n");
		goto release_host;
	}

	iwm_reset(iwm);

	ret = sdio_claim_irq(hw->func, iwm_sdio_isr);
	if (ret) {
		IWM_ERR(iwm, "Failed to claim irq: %d\n", ret);
		goto release_host;
	}

	sdio_writeb(hw->func, 1, IWM_SDIO_INTR_ENABLE_ADDR, &ret);
	if (ret < 0) {
		IWM_ERR(iwm, "Couldn't enable INTR: %d\n", ret);
		goto release_irq;
	}

	sdio_release_host(hw->func);

	IWM_DBG_SDIO(iwm, INFO, "IWM SDIO enable\n");

	return 0;

 release_irq:
	sdio_release_irq(hw->func);
 release_host:
	sdio_release_host(hw->func);

	return ret;
}

开发者ID:CSCLOG，项目名称:beaglebone，代码行数:42，代码来源:sdio.c

示例16: kalDevRegRead

/*----------------------------------------------------------------------------*/
BOOL
kalDevRegRead (
    IN  P_GLUE_INFO_T   prGlueInfo,
    IN  UINT_32         u4Register,
    OUT PUINT_32        pu4Value
)
{
    int ret = 0;
    int a = 0;

    ASSERT(prGlueInfo);
    ASSERT(pu4Value);

#if MTK_WCN_HIF_SDIO
    ret = mtk_wcn_hif_sdio_readl(prGlueInfo->rHifInfo.cltCtx, u4Register, (PUINT32) pu4Value);
#else
    if (!in_interrupt) {
        sdio_claim_host(prGlueInfo->rHifInfo.func);
    }

retry:
    *pu4Value = sdio_readl(prGlueInfo->rHifInfo.func, u4Register, &ret);
    if (ret && a < 10) {
        a++;
        printk("gwl =-==============> sdio_readl retry %d!\n", a);
        msleep(1);
        goto retry;
    }

    if (!in_interrupt) {
        sdio_release_host(prGlueInfo->rHifInfo.func);
    }
#endif

    if (ret) {
        kalSendAeeWarning(HIF_SDIO_ERR_TITLE_STR, HIF_SDIO_ERR_DESC_STR "sdio_readl() reports error: %x", ret);
        DBGLOG(HAL, ERROR, ("sdio_readl() reports error: %x", ret));
    }

    return (ret) ? FALSE : TRUE;
} /* end of kalDevRegRead() */

开发者ID:avila-devlogic，项目名称:D33_KK_Kernel，代码行数:42，代码来源:sdio.c

示例17: brcmf_sdioh_request_chain

/*
 * This function takes a queue of packets. The packets on the queue
 * are assumed to be properly aligned by the caller.
 */
int
brcmf_sdioh_request_chain(struct brcmf_sdio_dev *sdiodev, uint fix_inc,
			  uint write, uint func, uint addr,
			  struct sk_buff_head *pktq)
{
	bool fifo = (fix_inc == SDIOH_DATA_FIX);
	u32 SGCount = 0;
	int err_ret = 0;

	struct sk_buff *pkt;

	brcmf_dbg(TRACE, "Enter\n");

	brcmf_pm_resume_wait(sdiodev, &sdiodev->request_chain_wait);
	if (brcmf_pm_resume_error(sdiodev))
		return -EIO;

	/* Claim host controller */
	sdio_claim_host(sdiodev->func[func]);

	skb_queue_walk(pktq, pkt) {
		uint pkt_len = pkt->len;
		pkt_len += 3;
		pkt_len &= 0xFFFFFFFC;

		err_ret = brcmf_sdioh_request_data(sdiodev, write, fifo, func,
						   addr, pkt, pkt_len);
		if (err_ret) {
			brcmf_dbg(ERROR, "%s FAILED %p[%d], addr=0x%05x, pkt_len=%d, ERR=0x%08x\n",
				  write ? "TX" : "RX", pkt, SGCount, addr,
				  pkt_len, err_ret);
		} else {
			brcmf_dbg(TRACE, "%s xfr'd %p[%d], addr=0x%05x, len=%d\n",
				  write ? "TX" : "RX", pkt, SGCount, addr,
				  pkt_len);
		}
		if (!fifo)
			addr += pkt_len;

		SGCount++;
	}

开发者ID:nannaniel，项目名称:linux-2.6.35.3-imx28，代码行数:45，代码来源:bcmsdh_sdmmc.c

示例18: wl12xx_sdio_power_off

static int wl12xx_sdio_power_off(struct wl12xx_sdio_glue *glue)
{
	int ret;
	struct sdio_func *func = dev_to_sdio_func(glue->dev);
	struct mmc_card *card = func->card;

	sdio_claim_host(func);
	sdio_disable_func(func);
	sdio_release_host(func);

	/* Power off the card manually in case it wasn't powered off above */
	ret = mmc_power_save_host(card->host);
	if (ret < 0)
		goto out;

	/* Let runtime PM know the card is powered off */
	pm_runtime_put_sync(&card->dev);

out:
	return ret;
}

开发者ID:383530895，项目名称:linux，代码行数:21，代码来源:sdio.c

示例19: ssb_sdio_write32

static void ssb_sdio_write32(struct ssb_device *dev, u16 offset, u32 val)
{
	struct ssb_bus *bus = dev->bus;
	int error = 0;

	sdio_claim_host(bus->host_sdio);
	if (unlikely(ssb_sdio_switch_core(bus, dev)))
		goto out;
	offset |= bus->sdio_sbaddr & 0xffff;
	offset &= SBSDIO_SB_OFT_ADDR_MASK;
	offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */
	sdio_writel(bus->host_sdio, val, offset, &error);
	if (error) {
		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %08x, error %d\n",
			bus->sdio_sbaddr >> 16, offset, val, error);
	}
	if (bus->quirks & SSB_QUIRK_SDIO_READ_AFTER_WRITE32)
		sdio_readl(bus->host_sdio, 0, &error);
out:
	sdio_release_host(bus->host_sdio);
}

开发者ID:Medvedroid，项目名称:OT_903D-kernel-2.6.35.7，代码行数:21，代码来源:sdio.c

示例20: mtlte_sys_sdio_setup_irq

static int mtlte_sys_sdio_setup_irq(struct sdio_func *sdiofunc)
{
	int ret = 0 ;

	KAL_RAWPRINT(("[PROBE] =======> mtlte_sys_sdio_setup_irq\n")); 

	sdio_claim_host(sdiofunc);
    ret = sdio_claim_irq(sdiofunc, mtlte_sys_lte_sdio_isr);
    sdio_release_host(sdiofunc);

    if (ret){
        KAL_RAWPRINT(("[PROBE] XXXXXX mtlte_sys_sdio_setup_irq fail, %d \n", ret )); 
        return (ret);
    }

    mtlte_hif_enable_interrupt_at_probe();
    lte_sdio_enable_eirq();

    KAL_RAWPRINT(("[PROBE] <======= mtlte_sys_sdio_setup_irq\n")); 
    return 0 ;
}

开发者ID:Scorpio92，项目名称:mediatek，代码行数:21，代码来源:lte_main.c

注：本文中的sdio_claim_host函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ sdio_enable_func函数代码示例发布时间：2022-05-30

C++ sdhci_writeb函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19159|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9981|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8320|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8690|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8634|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9649|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8617|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7994|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8648|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7531|2022-11-06

客服电话

电子邮件

C++ sdio_claim_host函数代码示例

示例1: disable_sdio_interrupt

示例2: woal_sdio_read_write_cmd52

示例3: woal_register_dev

示例4: if_sdio_send_chunk

示例5: woal_unregister_dev

示例6: sd_f0_read8

示例7: smssdio_sendrequest

示例8: mwifiex_register_dev

示例9: woal_read_data_sync

示例10: mtk_sdio_remove

示例11: sbi_enable_host_int

示例12: sd_f0_write8

示例13: mtlte_sys_sdio_remove_irq

示例14: sif_enable_irq

示例15: if_sdio_enable

示例16: kalDevRegRead

示例17: brcmf_sdioh_request_chain

示例18: wl12xx_sdio_power_off

示例19: ssb_sdio_write32

示例20: mtlte_sys_sdio_setup_irq

请发表评论

全部评论

上一篇：

下一篇：

kojino/Harvard-Robust-Machine-Learning:

cescoffier/puppet-nexus: A Puppet Module

文的笔顺,诠释文的笔画,解读文的部首

abos3d/CleanArchitectKotlinFlowHiltSimpl

Cassolotl/sentient.cloud · GitHub

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053