C++ rtl_pcidev函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中rtl_pcidev函数的典型用法代码示例。如果您正苦于以下问题：C++ rtl_pcidev函数的具体用法？C++ rtl_pcidev怎么用？C++ rtl_pcidev使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了rtl_pcidev函数的17个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: rtl92s_init_aspm_vars

static void rtl92s_init_aspm_vars(struct ieee80211_hw *hw)
{
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));

	/*close ASPM for AMD defaultly */
	rtlpci->const_amdpci_aspm = 0;

	/*
	 * ASPM PS mode.
	 * 0 - Disable ASPM,
	 * 1 - Enable ASPM without Clock Req,
	 * 2 - Enable ASPM with Clock Req,
	 * 3 - Alwyas Enable ASPM with Clock Req,
	 * 4 - Always Enable ASPM without Clock Req.
	 * set defult to RTL8192CE:3 RTL8192E:2
	 * */
	rtlpci->const_pci_aspm = 2;

	/*Setting for PCI-E device */
	rtlpci->const_devicepci_aspm_setting = 0x03;

	/*Setting for PCI-E bridge */
	rtlpci->const_hostpci_aspm_setting = 0x02;

	/*
	 * In Hw/Sw Radio Off situation.
	 * 0 - Default,
	 * 1 - From ASPM setting without low Mac Pwr,
	 * 2 - From ASPM setting with low Mac Pwr,
	 * 3 - Bus D3
	 * set default to RTL8192CE:0 RTL8192SE:2
	 */
	rtlpci->const_hwsw_rfoff_d3 = 2;

	/*
	 * This setting works for those device with
	 * backdoor ASPM setting such as EPHY setting.
	 * 0 - Not support ASPM,
	 * 1 - Support ASPM,
	 * 2 - According to chipset.
	 */
	rtlpci->const_support_pciaspm = 2;
}

开发者ID:33d，项目名称:linux-2.6.21-hh20，代码行数:43，代码来源:sw.c

示例2: rtl92c_enable_interrupt

void rtl92c_enable_interrupt(struct ieee80211_hw *hw)
{
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	struct rtl_usb *rtlusb = rtl_usbdev(rtl_usbpriv(hw));

	if (IS_HARDWARE_TYPE_8192CE(rtlhal)) {
		rtl_write_dword(rtlpriv, REG_HIMR, rtlpci->irq_mask[0] &
				0xFFFFFFFF);
		rtl_write_dword(rtlpriv, REG_HIMRE, rtlpci->irq_mask[1] &
				0xFFFFFFFF);
	} else {
		rtl_write_dword(rtlpriv, REG_HIMR, rtlusb->irq_mask[0] &
				0xFFFFFFFF);
		rtl_write_dword(rtlpriv, REG_HIMRE, rtlusb->irq_mask[1] &
				0xFFFFFFFF);
	}
}

开发者ID:TaeheeYoo，项目名称:rtl8188eu，代码行数:19，代码来源:mac.c

示例3: rtl92c_init_sw_vars

int rtl92c_init_sw_vars(struct ieee80211_hw *hw)
{
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(12) | BIT(13);

	rtlpci->receive_config = (RCR_APP_FCS |
				  RCR_AMF |
				  RCR_ADF |
				  RCR_APP_MIC |
				  RCR_APP_ICV |
				  RCR_AICV |
				  RCR_ACRC32 |
				  RCR_AB |
				  RCR_AM |
				  RCR_APM |
				  RCR_APP_PHYST_RXFF | RCR_HTC_LOC_CTRL | 0);

	rtlpci->irq_mask[0] =
	    (u32) (IMR_ROK |
		   IMR_VODOK |
		   IMR_VIDOK |
		   IMR_BEDOK |
		   IMR_BKDOK |
		   IMR_MGNTDOK |
		   IMR_HIGHDOK | IMR_BDOK | IMR_RDU | IMR_RXFOVW | 0);

	rtlpci->irq_mask[1] = (u32) (IMR_CPWM | IMR_C2HCMD | 0);

	rtlpriv->rtlhal.pfirmware = (u8 *) vmalloc(0x4000);
	if (!rtlpriv->rtlhal.pfirmware) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 ("Can't alloc buffer for fw.\n"));
		return 1;
	}

	return 0;
}

开发者ID:ARMP，项目名称:android_kernel_lge_x3，代码行数:43，代码来源:sw.c

示例4: rtl92se_fw_cb

static void rtl92se_fw_cb(const struct firmware *firmware, void *context)
{
	struct ieee80211_hw *hw = context;
	struct rtl_pci_priv *pcipriv = rtl_pcipriv(hw);
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(pcipriv);
	struct rt_firmware *pfirmware = NULL;
	int err;

	RT_TRACE(rtlpriv, COMP_ERR, DBG_LOUD,
			 "Firmware callback routine entered!\n");
	complete(&rtlpriv->firmware_loading_complete);
	if (!firmware) {
		pr_err("Firmware %s not available\n", rtlpriv->cfg->fw_name);
		rtlpriv->max_fw_size = 0;
		return;
	}
	if (firmware->size > rtlpriv->max_fw_size) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 "Firmware is too big!\n");
		rtlpriv->max_fw_size = 0;
		release_firmware(firmware);
		return;
	}
	pfirmware = (struct rt_firmware *)rtlpriv->rtlhal.pfirmware;
	memcpy(pfirmware->sz_fw_tmpbuffer, firmware->data, firmware->size);
	pfirmware->sz_fw_tmpbufferlen = firmware->size;
	release_firmware(firmware);

	err = ieee80211_register_hw(hw);
	if (err) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 "Can't register mac80211 hw\n");
		return;
	} else {
		rtlpriv->mac80211.mac80211_registered = 1;
	}
	rtlpci->irq_alloc = 1;
	set_bit(RTL_STATUS_INTERFACE_START, &rtlpriv->status);

	/*init rfkill */
	rtl_init_rfkill(hw);
}

开发者ID:03199618，项目名称:linux，代码行数:43，代码来源:sw.c

示例5: rtl8822be_is_tx_desc_closed

bool rtl8822be_is_tx_desc_closed(struct ieee80211_hw *hw, u8 hw_queue,
				 u16 index)
{
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	bool ret = false;
	struct rtl8192_tx_ring *ring = &rtlpci->tx_ring[hw_queue];
	u16 cur_tx_rp, cur_tx_wp;
	u16 tmp16;

	/*
	 * design rule:
	 *     idx <= cur_tx_rp <= hw_rp <= cur_tx_wp = hw_wp
	 */

	if (index == ring->cur_tx_rp) {
		/* update only if sw_rp reach hw_rp */
		tmp16 = rtl_read_word(
			    rtlpriv,
			    get_desc_address_from_queue_index(hw_queue) + 2);

		cur_tx_rp = tmp16 & 0x01ff;
		cur_tx_wp = ring->cur_tx_wp;

		/* don't need to update ring->cur_tx_wp */
		ring->cur_tx_rp = cur_tx_rp;
	}

	if (index == ring->cur_tx_rp)
		ret = false;	/* no more */
	else
		ret = true;	/* more */

	if (hw_queue == BEACON_QUEUE)
		ret = true;

	if (rtlpriv->rtlhal.driver_is_goingto_unload ||
	    rtlpriv->psc.rfoff_reason > RF_CHANGE_BY_PS)
		ret = true;

	return ret;
}

开发者ID:mkrufky，项目名称:linux，代码行数:42，代码来源:trx.c

示例6: rtl88e_init_sw_vars

int rtl88e_init_sw_vars(struct ieee80211_hw *hw)
{
    int err = 0;
    struct rtl_priv *rtlpriv = rtl_priv(hw);
    struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
    u8 tid;

    rtl8188ee_bt_reg_init(hw);
    rtlpci->msi_support = rtlpriv->cfg->mod_params->msi_support;

    rtlpriv->dm.dm_initialgain_enable = 1;
    rtlpriv->dm.dm_flag = 0;
    rtlpriv->dm.disable_framebursting = 0;
    rtlpriv->dm.thermalvalue = 0;
    rtlpci->transmit_config = CFENDFORM | BIT(15);

    /* compatible 5G band 88ce just 2.4G band & smsp */
    rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
    rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
    rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

    rtlpci->receive_config = (RCR_APPFCS |
                              RCR_APP_MIC |
                              RCR_APP_ICV |
                              RCR_APP_PHYST_RXFF |
                              RCR_HTC_LOC_CTRL |
                              RCR_AMF |
                              RCR_ACF |
                              RCR_ADF |
                              RCR_AICV |
                              RCR_ACRC32 |
                              RCR_AB |
                              RCR_AM |
                              RCR_APM |
                              0);

    rtlpci->irq_mask[0] =
        (u32) (IMR_PSTIMEOUT	|
               IMR_HSISR_IND_ON_INT	|
               IMR_C2HCMD		|
               IMR_HIGHDOK		|
               IMR_MGNTDOK		|
               IMR_BKDOK		|
               IMR_BEDOK		|
               IMR_VIDOK		|
               IMR_VODOK		|
               IMR_RDU			|
               IMR_ROK			|
               0);
    rtlpci->irq_mask[1] = (u32) (IMR_RXFOVW | 0);
    rtlpci->sys_irq_mask = (u32) (HSIMR_PDN_INT_EN | HSIMR_RON_INT_EN);

    /* for debug level */
    rtlpriv->dbg.global_debuglevel = rtlpriv->cfg->mod_params->debug;
    /* for LPS & IPS */
    rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
    rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
    rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
    if (!rtlpriv->psc.inactiveps)
        pr_info("rtl8188ee: Power Save off (module option)\n");
    if (!rtlpriv->psc.fwctrl_lps)
        pr_info("rtl8188ee: FW Power Save off (module option)\n");
    rtlpriv->psc.reg_fwctrl_lps = 3;
    rtlpriv->psc.reg_max_lps_awakeintvl = 5;
    /* for ASPM, you can close aspm through
     * set const_support_pciaspm = 0
     */
    rtl88e_init_aspm_vars(hw);

    if (rtlpriv->psc.reg_fwctrl_lps == 1)
        rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
    else if (rtlpriv->psc.reg_fwctrl_lps == 2)
        rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
    else if (rtlpriv->psc.reg_fwctrl_lps == 3)
        rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

    /* for firmware buf */
    rtlpriv->rtlhal.pfirmware = vmalloc(0x8000);
    if (!rtlpriv->rtlhal.pfirmware) {
        RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
                 "Can't alloc buffer for fw.\n");
        return 1;
    }

    rtlpriv->cfg->fw_name = "rtlwifi/rtl8188efw.bin";
    rtlpriv->max_fw_size = 0x8000;
    pr_info("Using firmware %s\n", rtlpriv->cfg->fw_name);
    err = request_firmware_nowait(THIS_MODULE, 1, rtlpriv->cfg->fw_name,
                                  rtlpriv->io.dev, GFP_KERNEL, hw,
                                  rtl_fw_cb);
    if (err) {
        RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
                 "Failed to request firmware!\n");
        return 1;
    }

    /* for early mode */
    rtlpriv->rtlhal.earlymode_enable = false;
    rtlpriv->rtlhal.max_earlymode_num = 10;
    for (tid = 0; tid < 8; tid++)
//.........这里部分代码省略.........

开发者ID:mobilehunter，项目名称:trafficsqueezer-org，代码行数:101，代码来源:sw.c

示例7: rtl8723e_init_sw_vars

int rtl8723e_init_sw_vars(struct ieee80211_hw *hw)
{
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
	int err = 0;

	rtl8723e_bt_reg_init(hw);

	rtlpriv->btcoexist.btc_ops = rtl_btc_get_ops_pointer();

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(12) | BIT(13);

	/* compatible 5G band 88ce just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS |
				  RCR_APP_MIC |
				  RCR_APP_ICV |
				  RCR_APP_PHYST_RXFF |
				  RCR_HTC_LOC_CTRL |
				  RCR_AMF |
				  RCR_ACF |
				  RCR_ADF |
				  RCR_AICV |
				  RCR_AB |
				  RCR_AM |
				  RCR_APM |
				  0);

	rtlpci->irq_mask[0] =
	    (u32) (PHIMR_ROK |
		   PHIMR_RDU |
		   PHIMR_VODOK |
		   PHIMR_VIDOK |
		   PHIMR_BEDOK |
		   PHIMR_BKDOK |
		   PHIMR_MGNTDOK |
		   PHIMR_HIGHDOK |
		   PHIMR_C2HCMD |
		   PHIMR_HISRE_IND |
		   PHIMR_TSF_BIT32_TOGGLE |
		   PHIMR_TXBCNOK |
		   PHIMR_PSTIMEOUT |
		   0);

	rtlpci->irq_mask[1]	=
		 (u32)(PHIMR_RXFOVW |
				0);

	/* for debug level */
	rtlpriv->dbg.global_debuglevel = rtlpriv->cfg->mod_params->debug;
	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	if (rtlpriv->cfg->mod_params->disable_watchdog)
		pr_info("watchdog disabled\n");
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	rtl8723e_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(0x6000);
	if (!rtlpriv->rtlhal.pfirmware) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 "Can't alloc buffer for fw.\n");
		return 1;
	}

	if (IS_VENDOR_8723_A_CUT(rtlhal->version))
		rtlpriv->cfg->fw_name = "rtlwifi/rtl8723fw.bin";
	else if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version))
		rtlpriv->cfg->fw_name = "rtlwifi/rtl8723fw_B.bin";

	rtlpriv->max_fw_size = 0x6000;
	pr_info("Using firmware %s\n", rtlpriv->cfg->fw_name);
	err = request_firmware_nowait(THIS_MODULE, 1, rtlpriv->cfg->fw_name,
				      rtlpriv->io.dev, GFP_KERNEL, hw,
				      rtl_fw_cb);
	if (err) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 "Failed to request firmware!\n");
		return 1;
	}
	return 0;
}

开发者ID:Codefollows，项目名称:ps4-linux，代码行数:100，代码来源:sw.c

示例8: rtl8723be_init_sw_vars

int rtl8723be_init_sw_vars(struct ieee80211_hw *hw)
{
	int err = 0;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
	char *fw_name = "rtlwifi/rtl8723befw.bin";

	rtl8723be_bt_reg_init(hw);
	rtlpriv->btcoexist.btc_ops = rtl_btc_get_ops_pointer();

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(15) | BIT(24) | BIT(25);

	rtlpriv->phy.lck_inprogress = false;

	mac->ht_enable = true;

	/* compatible 5G band 88ce just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS		|
				  RCR_APP_MIC		|
				  RCR_APP_ICV		|
				  RCR_APP_PHYST_RXFF	|
				  RCR_HTC_LOC_CTRL	|
				  RCR_AMF		|
				  RCR_ACF		|
				  RCR_ADF		|
				  RCR_AICV		|
				  RCR_AB		|
				  RCR_AM		|
				  RCR_APM		|
				  0);

	rtlpci->irq_mask[0] = (u32) (IMR_PSTIMEOUT	|
				     IMR_HSISR_IND_ON_INT	|
				     IMR_C2HCMD		|
				     IMR_HIGHDOK	|
				     IMR_MGNTDOK	|
				     IMR_BKDOK		|
				     IMR_BEDOK		|
				     IMR_VIDOK		|
				     IMR_VODOK		|
				     IMR_RDU		|
				     IMR_ROK		|
				     0);

	rtlpci->irq_mask[1] = (u32)(IMR_RXFOVW | 0);

	rtlpci->sys_irq_mask = (u32)(HSIMR_PDN_INT_EN	|
				     HSIMR_RON_INT_EN	|
				     0);

	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	rtlpci->msi_support = rtlpriv->cfg->mod_params->msi_support;
	rtlpriv->cfg->mod_params->sw_crypto =
		 rtlpriv->cfg->mod_params->sw_crypto;
	rtlpriv->cfg->mod_params->disable_watchdog =
		 rtlpriv->cfg->mod_params->disable_watchdog;
	if (rtlpriv->cfg->mod_params->disable_watchdog)
		pr_info("watchdog disabled\n");
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0
	 */
	rtl8723be_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/*low power: Disable 32k */
	rtlpriv->psc.low_power_enable = false;

	rtlpriv->rtlhal.earlymode_enable = false;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(0x8000);
	if (!rtlpriv->rtlhal.pfirmware) {
		pr_err("Can't alloc buffer for fw.\n");
		return 1;
	}

	rtlpriv->max_fw_size = 0x8000;
	pr_info("Using firmware %s\n", fw_name);
	err = request_firmware_nowait(THIS_MODULE, 1, fw_name,
				      rtlpriv->io.dev, GFP_KERNEL, hw,
//.........这里部分代码省略.........

开发者ID:AshishNamdev，项目名称:linux，代码行数:101，代码来源:sw.c

示例9: rtl8821ae_init_sw_vars

/*InitializeVariables8812E*/
int rtl8821ae_init_sw_vars(struct ieee80211_hw *hw)
{
	int err = 0;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));

	rtl8821ae_bt_reg_init(hw);
	rtlpriv->btcoexist.btc_ops = rtl_btc_get_ops_pointer();

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(15) | BIT(24) | BIT(25);

	mac->ht_enable = true;
	mac->ht_cur_stbc = mac->ht_stbc_cap = 0;
	mac->vht_cur_ldpc = mac->vht_ldpc_cap = 0;
	mac->vht_cur_stbc = mac->vht_stbc_cap = 0;

	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	/*following 2 is for register 5G band, refer to _rtl_init_mac80211()*/
	rtlpriv->rtlhal.bandset = BAND_ON_BOTH;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS	|
				RCR_APP_MIC		|
				RCR_APP_ICV		|
				RCR_APP_PHYST_RXFF	|
				RCR_NONQOS_VHT		|
				RCR_HTC_LOC_CTRL	|
				RCR_AMF			|
				RCR_ACF			|
			/*This bit controls the PS-Poll packet filter.*/
				RCR_ADF			|
				RCR_AICV		|
				RCR_ACRC32		|
				RCR_AB			|
				RCR_AM			|
				RCR_APM			|
				0);


	rtlpci->irq_mask[0] =
	     (u32) (IMR_PSTIMEOUT			|
				IMR_GTINT3		|
				/*IMR_TBDER				|
				IMR_TBDOK				|
				IMR_BCNDMAINT0			|*/
				IMR_HSISR_IND_ON_INT	|
				IMR_C2HCMD		|
				IMR_HIGHDOK		|
				IMR_MGNTDOK		|
				IMR_BKDOK		|
				IMR_BEDOK		|
				IMR_VIDOK		|
				IMR_VODOK		|
				IMR_RDU			|
				IMR_ROK			|
				0);

	rtlpci->irq_mask[1]	=
		 (u32)(IMR_RXFOVW |
				IMR_TXFOVW |
				0);
	rtlpci->sys_irq_mask = (u32) (HSIMR_PDN_INT_EN	|
				      HSIMR_RON_INT_EN	|
				      0);
	/* for WOWLAN */
	/* if kernel >= 3.11, revise this var,
	 * remember revise 'rtl_wowlan_support' at the same time */
	rtlpriv->psc.wo_wlan_mode = WAKE_ON_MAGIC_PACKET |
				    WAKE_ON_PATTERN_MATCH;

	/* for debug level */
	rtlpriv->dbg.global_debuglevel = rtlpriv->cfg->mod_params->debug;
	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	rtlpci->msi_support = rtlpriv->cfg->mod_params->msi_support;
	rtlpci->int_clear = rtlpriv->cfg->mod_params->int_clear;
	rtlpriv->cfg->mod_params->sw_crypto =
		rtlpriv->cfg->mod_params->sw_crypto;
	rtlpriv->cfg->mod_params->disable_watchdog =
		rtlpriv->cfg->mod_params->disable_watchdog;
	if (rtlpriv->cfg->mod_params->disable_watchdog)
		pr_info("watchdog disabled\n");
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;

	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl8821ae_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
//.........这里部分代码省略.........

开发者ID:misac1987，项目名称:rtlwifi_new，代码行数:101，代码来源:sw.c

示例10: rtl8723e_init_sw_vars

int rtl8723e_init_sw_vars( struct ieee80211_hw *hw )
{
	int err = 0;
	struct rtl_priv *rtlpriv = rtl_priv( hw );
	struct rtl_pci *rtlpci = rtl_pcidev( rtl_pcipriv( hw ) );
	const struct firmware *firmware;
	struct rtl_hal *rtlhal = rtl_hal( rtl_priv( hw ) );
	char *fw_name = NULL;

	rtl8723e_bt_reg_init( hw );

	rtlpriv->dm.b_dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.b_disable_framebursting = 0;;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT( 12 ) | BIT( 13 );

	/* compatible 5G band 88ce just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = ( RCR_APPFCS |
				  RCR_APP_MIC |
				  RCR_APP_ICV |
				  RCR_APP_PHYST_RXFF |
				  RCR_HTC_LOC_CTRL |
				  RCR_AMF |
				  RCR_ACF |
				  RCR_ADF |
				  RCR_AICV |
				  RCR_AB |
				  RCR_AM |
				  RCR_APM |
				  0 );

	rtlpci->irq_mask[0] =
	    ( u32 ) ( PHIMR_ROK |
		   PHIMR_RDU |
		   PHIMR_VODOK |
		   PHIMR_VIDOK |
		   PHIMR_BEDOK |
		   PHIMR_BKDOK |
		   PHIMR_MGNTDOK |
		   PHIMR_HIGHDOK |
		   PHIMR_C2HCMD |
		   PHIMR_HISRE_IND |
		   PHIMR_TSF_BIT32_TOGGLE |
		   PHIMR_TXBCNOK |
		   PHIMR_PSTIMEOUT |
		   0 );

	rtlpci->irq_mask[1]	=
		 ( u32 )( 	PHIMR_RXFOVW |
				0 );

	/* for LPS & IPS */
	rtlpriv->psc.b_inactiveps = rtlpriv->cfg->mod_params->b_inactiveps;
	rtlpriv->psc.b_swctrl_lps = rtlpriv->cfg->mod_params->b_swctrl_lps;
	rtlpriv->psc.b_fwctrl_lps = rtlpriv->cfg->mod_params->b_fwctrl_lps;
	rtlpriv->psc.b_reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl8723e_init_aspm_vars( hw );

	if ( rtlpriv->psc.b_reg_fwctrl_lps == 1 )
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if ( rtlpriv->psc.b_reg_fwctrl_lps == 2 )
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if ( rtlpriv->psc.b_reg_fwctrl_lps == 3 )
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = ( u8 * ) vmalloc( 0x7000 );
	if ( !rtlpriv->rtlhal.pfirmware ) {
		RT_TRACE( COMP_ERR, DBG_EMERG,
			 ( "Can't alloc buffer for fw.\n" ) );
		return 1;
	}

	if ( IS_VENDOR_8723_A_CUT( rtlhal->version ) )
		fw_name = "rtlwifi/rtl8723fw.bin";
	else if ( IS_81xxC_VENDOR_UMC_B_CUT( rtlhal->version ) )
	{
		printk( "firemare: rtl8723fw_B.bin\n" );
		fw_name = "rtlwifi/rtl8723fw_B.bin";
	}

	err = request_firmware( &firmware, fw_name, rtlpriv->io.dev );
	if ( err ) {
		RT_TRACE( COMP_ERR, DBG_EMERG,
			 ( "Failed to request firmware!\n" ) );
		return 1;
	}

	if ( firmware->size > 0x6000 ) {
		RT_TRACE( COMP_ERR, DBG_EMERG,
			 ( "Firmware is too big!\n" ) );
		release_firmware( firmware );
//.........这里部分代码省略.........

开发者ID:jrosco，项目名称:rtl8188ce-linux-driver，代码行数:101，代码来源:sw.c

示例11: rtl8821ae_init_sw_vars

/*InitializeVariables8812E*/
int rtl8821ae_init_sw_vars(struct ieee80211_hw *hw)
{
	int err = 0;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	const struct firmware *firmware;
	struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
	char *fw_name = NULL;

	rtl8821ae_bt_reg_init(hw);
	rtlpriv->btcoexist.btc_ops = rtl_btc_get_ops_pointer();

	rtlpriv->dm.b_dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.b_disable_framebursting = 0;;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(15) | BIT(24) | BIT(25);

	mac->ht_enable = true;

	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	/*following 2 is for register 5G band, refer to _rtl_init_mac80211()*/
	rtlpriv->rtlhal.bandset = BAND_ON_BOTH;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS			|
							  RCR_APP_MIC 			|
							  RCR_APP_ICV 			|
							  RCR_APP_PHYST_RXFF	|
							  RCR_NONQOS_VHT		|
							  RCR_HTC_LOC_CTRL		|
							  RCR_AMF 				|
							  RCR_ACF 				|
							  RCR_ADF 				|	/*This bit controls the PS-Poll packet filter.*/
							  RCR_AICV				|
							  RCR_ACRC32			|
							  RCR_AB				|
							  RCR_AM				|
							  RCR_APM 				|
							  0);


	rtlpci->irq_mask[0] =
	     (u32) (IMR_PSTIMEOUT			|
				IMR_GTINT3 				|
				/*IMR_TBDER				|
				IMR_TBDOK				|
				IMR_BCNDMAINT0 			|*/
				IMR_HSISR_IND_ON_INT	|
				IMR_C2HCMD 				|
				IMR_HIGHDOK				|
				IMR_MGNTDOK				|
				IMR_BKDOK				|
				IMR_BEDOK				|
				IMR_VIDOK				|
				IMR_VODOK				|
				IMR_RDU					|
				IMR_ROK					|
				0);

	rtlpci->irq_mask[1]	=
		 (u32)(	IMR_RXFOVW |
		 		IMR_TXFOVW |
				0);

	/* for LPS & IPS */
	rtlpriv->psc.b_inactiveps = rtlpriv->cfg->mod_params->b_inactiveps;
	rtlpriv->psc.b_swctrl_lps = rtlpriv->cfg->mod_params->b_swctrl_lps;
	rtlpriv->psc.b_fwctrl_lps = rtlpriv->cfg->mod_params->b_fwctrl_lps;
	rtlpriv->psc.b_reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl8821ae_init_aspm_vars(hw);

	if (rtlpriv->psc.b_reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.b_reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.b_reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = (u8 *) vmalloc(0x8000);
	if (!rtlpriv->rtlhal.pfirmware) {
		RT_TRACE(COMP_ERR, DBG_EMERG,
			 ("Can't alloc buffer for fw.\n"));
		return 1;
	}

	fw_name = "rtlwifi/rtl8821aefw.bin";
	err = request_firmware(&firmware, fw_name, rtlpriv->io.dev);
	if (err) {
		RT_TRACE(COMP_ERR, DBG_EMERG,
			 ("Failed to request firmware!\n"));
		return 1;
	}

	if (firmware->size > 0x8000) {
//.........这里部分代码省略.........

开发者ID:IDM350，项目名称:linux，代码行数:101，代码来源:sw.c

示例12: rtl92ee_init_sw_vars

int rtl92ee_init_sw_vars(struct ieee80211_hw *hw)
{
	int err = 0;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));

	rtl92ee_bt_reg_init(hw);
	rtlpci->msi_support = rtlpriv->cfg->mod_params->msi_support;
	rtlpriv->btcoexist.btc_ops = rtl_btc_get_ops_pointer();

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	/*rtlpriv->dm.thermalvalue = 0;*/
	rtlpci->transmit_config = CFENDFORM | BIT(15);

	/*just 2.4G band*/
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS			|
				  RCR_APP_MIC			|
				  RCR_APP_ICV			|
				  RCR_APP_PHYST_RXFF		|
				  RCR_HTC_LOC_CTRL		|
				  RCR_AMF			|
				  RCR_ACF			|
				  RCR_ADF			|
				  RCR_AICV			|
				  RCR_ACRC32			|
				  RCR_AB			|
				  RCR_AM			|
				  RCR_APM			|
				  0);

	rtlpci->irq_mask[0] = (u32) (IMR_PSTIMEOUT		|
				/*   IMR_TBDER			|
				     IMR_TBDOK			|
				     IMR_BCNDMAINT0		|*/
				     IMR_C2HCMD			|
				     IMR_HIGHDOK		|
				     IMR_MGNTDOK		|
				     IMR_BKDOK			|
				     IMR_BEDOK			|
				     IMR_VIDOK			|
				     IMR_VODOK			|
				     IMR_RDU			|
				     IMR_ROK			|
				     0);
	rtlpci->irq_mask[1] = (u32) (IMR_RXFOVW | 0);

	/* for debug level */
	rtlpriv->dbg.global_debuglevel = rtlpriv->cfg->mod_params->debug;
	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	rtlpci->msi_support = rtlpriv->cfg->mod_params->msi_support;
	if (rtlpriv->cfg->mod_params->disable_watchdog)
		pr_info("watchdog disabled\n");
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl92ee_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for early mode */
	rtlpriv->rtlhal.earlymode_enable = false;

	/*low power */
	rtlpriv->psc.low_power_enable = false;


	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(0x8000);
	if (!rtlpriv->rtlhal.pfirmware) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 "Can't alloc buffer for fw\n");
		return 1;
	}

	/* request fw */
	rtlpriv->cfg->fw_name = "rtlwifi/rtl8192eefw.bin";

	rtlpriv->max_fw_size = 0x8000;
	pr_info("Using firmware %s\n", rtlpriv->cfg->fw_name);
	err = request_firmware_nowait(THIS_MODULE, 1, rtlpriv->cfg->fw_name,
				      rtlpriv->io.dev, GFP_KERNEL, hw,
				      rtl_fw_cb);
	if (err) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 "Failed to request firmware!\n");
//.........这里部分代码省略.........

开发者ID:EthanChoi，项目名称:rtlwifi_new，代码行数:101，代码来源:sw.c

示例13: rtl92d_init_sw_vars

static int rtl92d_init_sw_vars(struct ieee80211_hw *hw)
{
	int err;
	u8 tid;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	char *fw_name = "rtlwifi/rtl8192defw.bin";

	rtlpriv->dm.dm_initialgain_enable = true;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = false;
	rtlpriv->dm.thermalvalue = 0;
	rtlpriv->dm.useramask = true;

	/* dual mac */
	if (rtlpriv->rtlhal.current_bandtype == BAND_ON_5G)
		rtlpriv->phy.current_channel = 36;
	else
		rtlpriv->phy.current_channel = 1;

	if (rtlpriv->rtlhal.macphymode != SINGLEMAC_SINGLEPHY) {
		rtlpriv->rtlhal.disable_amsdu_8k = true;
		/* No long RX - reduce fragmentation */
		rtlpci->rxbuffersize = 4096;
	}

	rtlpci->transmit_config = CFENDFORM | BIT(12) | BIT(13);

	rtlpci->receive_config = (
			RCR_APPFCS
			| RCR_AMF
			| RCR_ADF
			| RCR_APP_MIC
			| RCR_APP_ICV
			| RCR_AICV
			| RCR_ACRC32
			| RCR_AB
			| RCR_AM
			| RCR_APM
			| RCR_APP_PHYST_RXFF
			| RCR_HTC_LOC_CTRL
	);

	rtlpci->irq_mask[0] = (u32) (
			IMR_ROK
			| IMR_VODOK
			| IMR_VIDOK
			| IMR_BEDOK
			| IMR_BKDOK
			| IMR_MGNTDOK
			| IMR_HIGHDOK
			| IMR_BDOK
			| IMR_RDU
			| IMR_RXFOVW
	);

	rtlpci->irq_mask[1] = (u32) (IMR_CPWM | IMR_C2HCMD);

	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	if (!rtlpriv->psc.inactiveps)
		pr_info("Power Save off (module option)\n");
	if (!rtlpriv->psc.fwctrl_lps)
		pr_info("FW Power Save off (module option)\n");
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl92d_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for early mode */
	rtlpriv->rtlhal.earlymode_enable = false;
	for (tid = 0; tid < 8; tid++)
		skb_queue_head_init(&rtlpriv->mac80211.skb_waitq[tid]);

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(0x8000);
	if (!rtlpriv->rtlhal.pfirmware) {
		pr_err("Can't alloc buffer for fw\n");
		return 1;
	}

	rtlpriv->max_fw_size = 0x8000;
	pr_info("Driver for Realtek RTL8192DE WLAN interface\n");
	pr_info("Loading firmware file %s\n", fw_name);

	/* request fw */
	err = request_firmware_nowait(THIS_MODULE, 1, fw_name,
				      rtlpriv->io.dev, GFP_KERNEL, hw,
				      rtl_fw_cb);
	if (err) {
//.........这里部分代码省略.........

开发者ID:AlexShiLucky，项目名称:linux，代码行数:101，代码来源:sw.c

示例14: rtl92c_init_sw_vars

int rtl92c_init_sw_vars(struct ieee80211_hw *hw)
{
	int err;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	const struct firmware *firmware;

	rtl8192ce_bt_reg_init(hw);

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(12) | BIT(13);

	/* compatible 5G band 88ce just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS |
				  RCR_AMF |
				  RCR_ADF |
				  RCR_APP_MIC |
				  RCR_APP_ICV |
				  RCR_AICV |
				  RCR_ACRC32 |
				  RCR_AB |
				  RCR_AM |
				  RCR_APM |
				  RCR_APP_PHYST_RXFF | RCR_HTC_LOC_CTRL | 0);

	rtlpci->irq_mask[0] =
	    (u32) (IMR_ROK |
		   IMR_VODOK |
		   IMR_VIDOK |
		   IMR_BEDOK |
		   IMR_BKDOK |
		   IMR_MGNTDOK |
		   IMR_HIGHDOK | IMR_BDOK | IMR_RDU | IMR_RXFOVW | 0);

	rtlpci->irq_mask[1] = (u32) (IMR_CPWM | IMR_C2HCMD | 0);

	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl92c_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(0x4000);
	if (!rtlpriv->rtlhal.pfirmware) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 ("Can't alloc buffer for fw.\n"));
		return 1;
	}

	/* request fw */
	err = request_firmware(&firmware, rtlpriv->cfg->fw_name,
			rtlpriv->io.dev);
	if (err) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 ("Failed to request firmware!\n"));
		return 1;
	}
	if (firmware->size > 0x4000) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 ("Firmware is too big!\n"));
		release_firmware(firmware);
		return 1;
	}
	memcpy(rtlpriv->rtlhal.pfirmware, firmware->data, firmware->size);
	rtlpriv->rtlhal.fwsize = firmware->size;
	release_firmware(firmware);

	return 0;
}

开发者ID:119-org，项目名称:hi3518-osdrv，代码行数:88，代码来源:sw.c

示例15: rtl92s_init_sw_vars

static int rtl92s_init_sw_vars(struct ieee80211_hw *hw)
{
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	int err = 0;
	u16 earlyrxthreshold = 7;

	rtlpriv->dm.dm_initialgain_enable = true;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = false;
	rtlpriv->dm.thermalvalue = 0;
	rtlpriv->dm.useramask = true;

	/* compatible 5G band 91se just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->transmit_config = 0;

	rtlpci->receive_config =
			RCR_APPFCS |
			RCR_APWRMGT |
			/*RCR_ADD3 |*/
			RCR_AMF	|
			RCR_ADF |
			RCR_APP_MIC |
			RCR_APP_ICV |
			RCR_AICV |
			/* Accept ICV error, CRC32 Error */
			RCR_ACRC32 |
			RCR_AB |
			/* Accept Broadcast, Multicast */
			RCR_AM	|
			/* Accept Physical match */
			RCR_APM |
			/* Accept Destination Address packets */
			/*RCR_AAP |*/
			RCR_APP_PHYST_STAFF |
			/* Accept PHY status */
			RCR_APP_PHYST_RXFF |
			(earlyrxthreshold << RCR_FIFO_OFFSET);

	rtlpci->irq_mask[0] = (u32)
			(IMR_ROK |
			IMR_VODOK |
			IMR_VIDOK |
			IMR_BEDOK |
			IMR_BKDOK |
			IMR_HCCADOK |
			IMR_MGNTDOK |
			IMR_COMDOK |
			IMR_HIGHDOK |
			IMR_BDOK |
			IMR_RXCMDOK |
			/*IMR_TIMEOUT0 |*/
			IMR_RDU |
			IMR_RXFOVW	|
			IMR_BCNINT
			/*| IMR_TXFOVW*/
			/*| IMR_TBDOK |
			IMR_TBDER*/);

	rtlpci->irq_mask[1] = (u32) 0;

	rtlpci->shortretry_limit = 0x30;
	rtlpci->longretry_limit = 0x30;

	rtlpci->first_init = true;

	/* for debug level */
	rtlpriv->dbg.global_debuglevel = rtlpriv->cfg->mod_params->debug;
	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	if (!rtlpriv->psc.inactiveps)
		pr_info("Power Save off (module option)\n");
	if (!rtlpriv->psc.fwctrl_lps)
		pr_info("FW Power Save off (module option)\n");
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl92s_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(sizeof(struct rt_firmware));
	if (!rtlpriv->rtlhal.pfirmware)
		return 1;

	rtlpriv->max_fw_size = RTL8190_MAX_FIRMWARE_CODE_SIZE*2 +
			       sizeof(struct fw_hdr);
//.........这里部分代码省略.........

开发者ID:shinsec，项目名称:linux-parrot，代码行数:101，代码来源:sw.c

示例16: rtl92s_init_sw_vars

static int rtl92s_init_sw_vars(struct ieee80211_hw *hw)
{
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	const struct firmware *firmware;
	struct rt_firmware *pfirmware = NULL;
	int err = 0;
	u16 earlyrxthreshold = 7;

	rtlpriv->dm.dm_initialgain_enable = 1;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = 0;
	rtlpriv->dm.thermalvalue = 0;
	rtlpriv->dm.useramask = true;

	/* compatible 5G band 91se just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->transmit_config = 0;

	rtlpci->receive_config =
			RCR_APPFCS |
			RCR_APWRMGT |
			/*RCR_ADD3 |*/
			RCR_AMF	|
			RCR_ADF |
			RCR_APP_MIC |
			RCR_APP_ICV |
			RCR_AICV |
			/* Accept ICV error, CRC32 Error */
			RCR_ACRC32 |
			RCR_AB |
			/* Accept Broadcast, Multicast */
			RCR_AM	|
			/* Accept Physical match */
			RCR_APM |
			/* Accept Destination Address packets */
			/*RCR_AAP |*/
			RCR_APP_PHYST_STAFF |
			/* Accept PHY status */
			RCR_APP_PHYST_RXFF |
			(earlyrxthreshold << RCR_FIFO_OFFSET);

	rtlpci->irq_mask[0] = (u32)
			(IMR_ROK |
			IMR_VODOK |
			IMR_VIDOK |
			IMR_BEDOK |
			IMR_BKDOK |
			IMR_HCCADOK |
			IMR_MGNTDOK |
			IMR_COMDOK |
			IMR_HIGHDOK |
			IMR_BDOK |
			IMR_RXCMDOK |
			/*IMR_TIMEOUT0 |*/
			IMR_RDU |
			IMR_RXFOVW	|
			IMR_BCNINT
			/*| IMR_TXFOVW*/
			/*| IMR_TBDOK |
			IMR_TBDER*/);

	rtlpci->irq_mask[1] = (u32) 0;

	rtlpci->shortretry_limit = 0x30;
	rtlpci->longretry_limit = 0x30;

	rtlpci->first_init = true;

	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	rtlpriv->psc.reg_fwctrl_lps = 3;
	rtlpriv->psc.reg_max_lps_awakeintvl = 5;
	/* for ASPM, you can close aspm through
	 * set const_support_pciaspm = 0 */
	rtl92s_init_aspm_vars(hw);

	if (rtlpriv->psc.reg_fwctrl_lps == 1)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MIN_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 2)
		rtlpriv->psc.fwctrl_psmode = FW_PS_MAX_MODE;
	else if (rtlpriv->psc.reg_fwctrl_lps == 3)
		rtlpriv->psc.fwctrl_psmode = FW_PS_DTIM_MODE;

	/* for firmware buf */
	rtlpriv->rtlhal.pfirmware = vzalloc(sizeof(struct rt_firmware));
	if (!rtlpriv->rtlhal.pfirmware) {
		RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
			 ("Can't alloc buffer for fw.\n"));
		return 1;
	}

	pr_info("Driver for Realtek RTL8192SE/RTL8191SE\n"
		"Loading firmware %s\n", rtlpriv->cfg->fw_name);
	/* request fw */
//.........这里部分代码省略.........

开发者ID:abnarain，项目名称:mac80211-darkbranch，代码行数:101，代码来源:sw.c

示例17: rtl92c_init_sw_vars

int rtl92c_init_sw_vars(struct ieee80211_hw *hw)
{
	int err;
	struct rtl_priv *rtlpriv = rtl_priv(hw);
	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));

	rtl8192ce_bt_reg_init(hw);

	rtlpriv->dm.dm_initialgain_enable = true;
	rtlpriv->dm.dm_flag = 0;
	rtlpriv->dm.disable_framebursting = false;
	rtlpriv->dm.thermalvalue = 0;
	rtlpci->transmit_config = CFENDFORM | BIT(12) | BIT(13);

	/* compatible 5G band 88ce just 2.4G band & smsp */
	rtlpriv->rtlhal.current_bandtype = BAND_ON_2_4G;
	rtlpriv->rtlhal.bandset = BAND_ON_2_4G;
	rtlpriv->rtlhal.macphymode = SINGLEMAC_SINGLEPHY;

	rtlpci->receive_config = (RCR_APPFCS |
				  RCR_AMF |
				  RCR_ADF |
				  RCR_APP_MIC |
				  RCR_APP_ICV |
				  RCR_AICV |
				  RCR_ACRC32 |
				  RCR_AB |
				  RCR_AM |
				  RCR_APM |
				  RCR_APP_PHYST_RXFF | RCR_HTC_LOC_CTRL | 0);

	rtlpci->irq_mask[0] =
	    (u32) (IMR_ROK |
		   IMR_VODOK |
		   IMR_VIDOK |
		   IMR_BEDOK |
		   IMR_BKDOK |
		   IMR_MGNTDOK |
		   IMR_HIGHDOK | IMR_BDOK | IMR_RDU | IMR_RXFOVW | 0);

	rtlpci->irq_mask[1] = (u32) (IMR_CPWM | IMR_C2HCMD | 0);

	/* for debug level */
	rtlpriv->dbg.global_debuglevel = rtlpriv->cfg->mod_params->debug;
	/* for LPS & IPS */
	rtlpriv->psc.inactiveps = rtlpriv->cfg->mod_params->inactiveps;
	rtlpriv->psc.swctrl_lps = rtlpriv->cfg->mod_params->swctrl_lps;
	rtlpriv->psc.fwctrl_lps = rtlpriv->cfg->mod_params->fwctrl_lps;
	if (!rtlpriv->psc.inactiveps)
		pr_info("rtl8192ce: Power Save off (module option)\n");
	if (!rtlpriv->psc.fwctrl_lps)
		pr

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ rtl_pcipriv函数代码示例发布时间：2022-05-30

C++ rtl_psc函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

2023-10-27

florent37/ViewAnimator: A fluent Android

2022-08-15

florent37/Shrine-MaterialDesign2: implem

2022-08-17

CVE-2020-36276

2022-09-23

SimpleSoftwareIO/simple-sms: Send and re

2022-08-13

阅读排行榜

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19168|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9982|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8322|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8691|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8635|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9651|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8618|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7995|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8649|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7532|2022-11-06

客服电话

电子邮件