C++ rt_hw_serial_isr函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中rt_hw_serial_isr函数的典型用法代码示例。如果您正苦于以下问题：C++ rt_hw_serial_isr函数的具体用法？C++ rt_hw_serial_isr怎么用？C++ rt_hw_serial_isr使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了rt_hw_serial_isr函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: rt_fh_uart_handler

void rt_fh_uart_handler(int vector, void *param)
{
    int status;
    unsigned int ret;
    struct fh_uart *uart;
    unsigned int reg_status;
    rt_device_t dev = (rt_device_t)param;
    uart = (struct fh_uart *)dev->user_data;
    status = uart_get_iir_status(uart->uart_port);
    if (status & UART_IIR_NOINT)
    {
        return;
    }
    if(status & UART_IIR_THREMPTY) {
        //first close tx isr
        uart_disable_irq(uart->uart_port,UART_IER_ETBEI);

        rt_hw_serial_isr((struct rt_serial_device *)dev, RT_SERIAL_EVENT_TX_DONE);
    }
    else if((status & UART_IIR_CHRTOUT)==UART_IIR_CHRTOUT) {
        //bug....
        //if no data in rx fifo
        reg_status = uart_get_status(uart->uart_port);
        if((reg_status & 1<<3) == 0)
            ret = uart_getc(uart->uart_port);
    }
    else {
        rt_interrupt_enter();
        rt_hw_serial_isr((struct rt_serial_device *)dev, RT_SERIAL_EVENT_RX_IND);
        rt_interrupt_leave();
    }
}

开发者ID:hezlog，项目名称:rt-thread，代码行数:32，代码来源:uart.c

示例2: UART0_IRQHandler

void UART0_IRQHandler(void)
{
    if (nrf_uart_int_enable_check(NRF_UART0, NRF_UART_INT_MASK_ERROR)
        && nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_ERROR))
    {
        nrf_uart_event_clear(NRF_UART0, NRF_UART_EVENT_ERROR);
    }

    if (nrf_uart_int_enable_check(NRF_UART0, NRF_UART_INT_MASK_RXDRDY)
        && nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_RXDRDY))
    {
        rt_hw_serial_isr(working_cfg->serial, RT_SERIAL_EVENT_RX_IND);
    }

    if (nrf_uart_int_enable_check(NRF_UART0, NRF_UART_INT_MASK_TXDRDY)
        && nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_TXDRDY))
    {
        rt_hw_serial_isr(working_cfg->serial, RT_SERIAL_EVENT_TX_DONE);
    }

    if (nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_RXTO))
    {
        rt_hw_serial_isr(working_cfg->serial, RT_SERIAL_EVENT_RX_TIMEOUT);
    }
}

开发者ID:heyuanjie87，项目名称:rt-thread，代码行数:25，代码来源:uart.c

示例3: USART1_IRQHandler

void USART1_IRQHandler(void)
{
    struct stm32_uart* uart;

    uart = &uart1;

    /* enter interrupt */
    rt_interrupt_enter();
    if(USART_GetITStatus(uart->uart_device, USART_IT_RXNE) != RESET)
    {
        rt_hw_serial_isr(&serial1, RT_SERIAL_EVENT_RX_IND);
        /* clear interrupt */
        USART_ClearITPendingBit(uart->uart_device, USART_IT_RXNE);
    }

    if (USART_GetITStatus(uart->uart_device, uart->tx_irq_type) != RESET)
    {
        /* clear interrupt */
        rt_hw_serial_isr(&serial1, RT_SERIAL_EVENT_TX_DONE);
        if (uart->tx_irq_type == USART_IT_TC)
        {
            USART_ClearITPendingBit(uart->uart_device, uart->tx_irq_type);
        }
    }
    if (USART_GetFlagStatus(uart->uart_device, USART_FLAG_ORE) == SET)
    {
        stm32_getc(&serial1);
    }
    /* leave interrupt */
    rt_interrupt_leave();
}

开发者ID:pengleo392，项目名称:FreeModbus_Slave-Master-RTT-STM32，代码行数:31，代码来源:usart.c

示例4: UART0_RX_TX_IRQHandler

/* Implementation of UART0 handler named in startup code. */
void UART0_RX_TX_IRQHandler(void)
{
    rt_interrupt_enter();
    rt_hw_serial_isr((struct rt_serial_device*)&_kinetis_serial, RT_SERIAL_EVENT_RX_IND);
    //UART_DRV_IRQHandler(0);
    rt_interrupt_leave();
}

开发者ID:RT-Thread，项目名称:rtthread_fsl，代码行数:8，代码来源:fsl_uart_irq_rt.c

示例5: uart_isr

/**
 * Uart common interrupt process. This need add to uart ISR.
 *
 * @param serial serial device
 */
static void uart_isr(struct rt_serial_device *serial)
{
    struct imxrt_uart *uart;
    LPUART_Type *base;

    RT_ASSERT(serial != RT_NULL);

    uart = (struct imxrt_uart *) serial->parent.user_data;
    RT_ASSERT(uart != RT_NULL);

    base = uart->uart_base;
    RT_ASSERT(base != RT_NULL);

    /* enter interrupt */
    rt_interrupt_enter();

    /* UART in mode Receiver -------------------------------------------------*/
    if (LPUART_GetStatusFlags(base) & kLPUART_RxDataRegFullFlag)
    {
        rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_IND);
    }

    /* If RX overrun. */
    if (LPUART_STAT_OR_MASK & base->STAT)
    {
        /* Clear overrun flag, otherwise the RX does not work. */
        base->STAT = ((base->STAT & 0x3FE00000U) | LPUART_STAT_OR_MASK);
    }

    /* leave interrupt */
    rt_interrupt_leave();
}

开发者ID:geniusgogo，项目名称:rt-thread，代码行数:37，代码来源:drv_uart.c

示例6: _ep_out_handler

/**
 * This function will handle cdc bulk out endpoint request.
 *
 * @param func the usb function object.
 * @param size request size.
 *
 * @return RT_EOK.
 */
static rt_err_t _ep_out_handler(ufunction_t func, rt_size_t size)
{
    rt_uint32_t level;
    struct vcom *data;

    RT_ASSERT(func != RT_NULL);

    RT_DEBUG_LOG(RT_DEBUG_USB, ("_ep_out_handler %d\n", size));
    
    data = (struct vcom*)func->user_data;
    /* receive data from USB VCOM */
    level = rt_hw_interrupt_disable();

    rt_ringbuffer_put(&data->rx_ringbuffer, data->ep_out->buffer, size);
    rt_hw_interrupt_enable(level);

    /* notify receive data */
    rt_hw_serial_isr(&data->serial);

    data->ep_out->request.buffer = data->ep_out->buffer;
    data->ep_out->request.size = EP_MAXPACKET(data->ep_out);
    data->ep_out->request.req_type = UIO_REQUEST_READ_MOST;    
    rt_usbd_io_request(func->device, data->ep_out, &data->ep_out->request);

    return RT_EOK;
}

开发者ID:cedar-renjun，项目名称:air-conditioning-assistant，代码行数:34，代码来源:cdc_vcom.c

示例7: UART4_IRQHandler

void UART4_IRQHandler(void)
{
    struct stm32_uart* uart;

    uart = &uart4;

    /* enter interrupt */
    rt_interrupt_enter();
    if(USART_GetITStatus(uart->uart_device, USART_IT_RXNE) != RESET)
    {
        rt_hw_serial_isr(&serial4, RT_SERIAL_EVENT_RX_IND);
        /* clear interrupt */
        USART_ClearITPendingBit(uart->uart_device, USART_IT_RXNE);
    }
    if (USART_GetITStatus(uart->uart_device, USART_IT_TC) != RESET)
    {
        /* clear interrupt */
        USART_ClearITPendingBit(uart->uart_device, USART_IT_TC);
    }
    if (USART_GetFlagStatus(uart->uart_device, USART_FLAG_ORE) == SET)
    {
        stm32_getc(&serial4);
    }

    /* leave interrupt */
    rt_interrupt_leave();
}

开发者ID:AdrianHuang，项目名称:rt-thread，代码行数:27，代码来源:usart.c

示例8: CME_UART_IRQHandler

static void CME_UART_IRQHandler(struct rt_serial_device *serial)
{
    struct CME_M7_uart* uart;

    RT_ASSERT(serial != RT_NULL);
    uart = (struct CME_M7_uart *)serial->parent.user_data;

    if(UART_GetIntStatus(uart->uart_device, UART_Int_RxNotEmpty))
    {
        UART_ClearInt(uart->uart_device, UART_Int_RxNotEmpty);
        rt_hw_serial_isr(&serial2, RT_SERIAL_EVENT_RX_IND);
    }

    if(UART_GetIntStatus(uart->uart_device, UART_Int_RxThresholdReach))
    {
        UART_ClearInt(uart->uart_device, UART_Int_RxThresholdReach);
    }

    if(UART_GetIntStatus(uart->uart_device, UART_Int_OverrunError))
    {
        UART_ClearInt(uart->uart_device, UART_Int_OverrunError);
    }

    if(UART_GetIntStatus(uart->uart_device, UART_Int_FrameError))
    {
        UART_ClearInt(uart->uart_device, UART_Int_FrameError);
    }

    if(UART_GetIntStatus(uart->uart_device, UART_Int_ParityError))
    {
        UART_ClearInt(uart->uart_device, UART_Int_ParityError);
    }
}

开发者ID:54chenjq，项目名称:rt-thread，代码行数:33，代码来源:uart.c

示例9: MFS3RX_IRQHandler

void MFS3RX_IRQHandler(void)
{
	/* enter interrupt */
	rt_interrupt_enter();
	rt_hw_serial_isr(&serial3, RT_SERIAL_EVENT_RX_IND);
	/* leave interrupt */
	rt_interrupt_leave();
}

开发者ID:AdrianHuang，项目名称:rt-thread，代码行数:8，代码来源:fm3_uart.c

示例10: USART1_IRQHandler

void USART1_IRQHandler(void) {
    struct usart_dev* usart_dev = Serial1.c_dev();

    rt_interrupt_enter();
    if (usart_dev->regs->SR & USART_SR_RXNE) {
        rt_hw_serial_isr(&serial1, RT_SERIAL_EVENT_RX_IND);
    }
    rt_interrupt_leave();
}

开发者ID:hongyegb123，项目名称:wrtnode2r_stm32，代码行数:9，代码来源:usart.c

示例11: USART2_Handler

void USART2_Handler(void)
{
    /* enter interrupt */
    rt_interrupt_enter();

    rt_hw_serial_isr(&usart2.serial);

    /* leave interrupt */
    rt_interrupt_leave();
}

开发者ID:david1mdavis，项目名称:SAM4N，代码行数:10，代码来源:drv_usart.c

示例12: dbg_uart_irq_handler

void dbg_uart_irq_handler(void * data)
{
    u32 IrqEn = DiagGetIsrEnReg();

    DiagSetIsrEnReg(0);

    rt_hw_serial_isr(&ameba_dbg_serial, RT_SERIAL_EVENT_RX_IND);
    
    DiagSetIsrEnReg(IrqEn);
}

开发者ID:DigFarmer，项目名称:rt-thread，代码行数:10，代码来源:drv_uart.c

示例13: UART1_RX_TX_IRQHandler

/* Implementation of UART1 handler named in startup code. */
void UART1_RX_TX_IRQHandler(void)
{
    rt_interrupt_enter();
    rt_hw_serial_isr((struct rt_serial_device*)&_kinetis_serial, RT_SERIAL_EVENT_RX_IND);
    /* Disable receive data full and rx overrun interrupt */
    //UART_BWR_C2_RIE(g_uartBase[1], 0U);
    //UART_HAL_SetIntMode(g_uartBase[1], kUartIntRxOverrun, false);
    //UART_BWR_C2_TIE(g_uartBase[1], 0U);
    rt_interrupt_leave();
}

开发者ID:RT-Thread，项目名称:rtthread_fsl，代码行数:11，代码来源:fsl_uart_irq_rt.c

示例14: ameba_uart_irq

static void ameba_uart_irq(uint32_t id, SerialIrq event)
{
    struct rt_serial_device *serial = (struct rt_serial_device *)id;
	if(event == RxIrq)
    {
        rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_IND);
	}
	else if(event == TxIrq)
    {
	}
}

开发者ID:DigFarmer，项目名称:rt-thread，代码行数:11，代码来源:drv_uart.c

示例15: USART1_IRQHandler

/*******************************************************************************
* Function Name  : USART1_IRQHandler
* Description    : This function handles USART1 global interrupt request.
* Input          : None
* Output         : None
* Return         : None
*******************************************************************************/
void USART1_IRQHandler(void)
{
#ifdef RT_USING_UART1
    extern struct rt_device uart1_device;
    /* enter interrupt */
    rt_interrupt_enter();

    rt_hw_serial_isr(&uart1_device);

    /* leave interrupt */
    rt_interrupt_leave();
#endif
}

开发者ID:Manish-cimcon，项目名称:micro，代码行数:20，代码来源:stm32f10x_it.c

示例16: UART0_UART1_UART2_UART3_IRQHandler

/* Implementation of UART5 handler named in startup code. */
void UART0_UART1_UART2_UART3_IRQHandler(void)
{
  rt_interrupt_enter();
      rt_hw_serial_isr((struct rt_serial_device*)&_kinetis_serial, RT_SERIAL_EVENT_RX_IND);
    for(uint32_t i=0; i < UART_INSTANCE_COUNT; i++)
    {
        if (CLOCK_SYS_GetUartGateCmd(i))
        {
            UART_DRV_IRQHandler(i);   
        }
    }
       rt_interrupt_leave();
}

开发者ID:RT-Thread，项目名称:rtthread_fsl，代码行数:14，代码来源:fsl_uart_irq_rt.c

示例17: rt_hw_serial_isr

/**/void USART2_IRQHandler(void)
{
    extern struct rt_device uart2_device;
	extern void rt_hw_serial_isr(struct rt_device *device);

    // enter interrupt 
    rt_interrupt_enter();

    rt_hw_serial_isr(&uart2_device);

    // leave interrupt 
    rt_interrupt_leave();
}

开发者ID:TIMCHENY，项目名称:STM32F107Board-rttproject，代码行数:13，代码来源:stm32f10x_it.c

示例18: USART3_IRQHandler

/*******************************************************************************
* Function Name  : USART3_IRQHandler
* Description    : This function handles USART3 global interrupt request.
* Input          : None
* Output         : None
* Return         : None
*******************************************************************************/
 void USART3_IRQHandler(void)
{
#ifdef RT_USING_UART3
    extern struct rt_device uart3_device;
	extern void rt_hw_serial_isr(struct rt_device *device);

    // enter interrupt 
    rt_interrupt_enter();

    rt_hw_serial_isr(&uart3_device);

    // leave interrupt 
    rt_interrupt_leave();
#endif
}

开发者ID:dengkuanchina，项目名称:STM32F107Board-rttproject，代码行数:22，代码来源:stm32f10x_it.c

示例19: uart_isr

/**
 * Uart common interrupt process. This need add to uart ISR.
 *
 * @param serial serial device
 */
static void uart_isr(struct rt_serial_device *serial)
{
    struct gd32_uart *uart = (struct gd32_uart *) serial->parent.user_data;

    RT_ASSERT(uart != RT_NULL);

    /* UART in mode Receiver */
    if ((usart_interrupt_flag_get(uart->uart_periph, USART_INT_FLAG_RBNE) != RESET) &&
            (usart_flag_get(uart->uart_periph, USART_FLAG_RBNE) != RESET))
    {
        rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_IND);
        /* Clear RXNE interrupt flag */
        usart_flag_clear(uart->uart_periph, USART_FLAG_RBNE);
    }
}

开发者ID:BernardXiong，项目名称:rt-thread，代码行数:20，代码来源:drv_usart.c

示例20: uart_isr

/**
 * 中断处理函数
 */
static void uart_isr(usart_t serial)
{
    // 获取串口基地址
    UART_T *uart_base = ((usart_t)serial)->usart_base;

    // 获取中断事件
    uint32_t u32IntSts= uart_base->INTSTS;

    // 接收中断
    if(u32IntSts & (UART_INTSTS_RDAINT_Msk | UART_INTSTS_RXTOINT_Msk))
    {
        rt_hw_serial_isr(&serial->dev, RT_SERIAL_EVENT_RX_IND);
    }

}

开发者ID:heyuanjie87，项目名称:rt-thread，代码行数:18，代码来源:drv_uart.c

注：本文中的rt_hw_serial_isr函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ rt_interrupt_enter函数代码示例发布时间：2022-05-30

C++ rt_hw_interrupt_disable函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19170|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9982|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8322|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8691|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8635|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9651|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8618|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7995|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8649|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7532|2022-11-06

客服电话

电子邮件

C++ rt_hw_serial_isr函数代码示例

示例1: rt_fh_uart_handler

示例2: UART0_IRQHandler

示例3: USART1_IRQHandler

示例4: UART0_RX_TX_IRQHandler

示例5: uart_isr

示例6: _ep_out_handler

示例7: UART4_IRQHandler

示例8: CME_UART_IRQHandler

示例9: MFS3RX_IRQHandler

示例10: USART1_IRQHandler

示例11: USART2_Handler

示例12: dbg_uart_irq_handler

示例13: UART1_RX_TX_IRQHandler

示例14: ameba_uart_irq

示例15: USART1_IRQHandler

示例16: UART0_UART1_UART2_UART3_IRQHandler

示例17: rt_hw_serial_isr

示例18: USART3_IRQHandler

示例19: uart_isr

示例20: uart_isr

请发表评论

全部评论

上一篇：

下一篇：

CVE-2022-32051

xorrior/macOSTools: macOS Offensive Tool

caseypugh/minecraft: Some scripts to mak

Testinium/MobileDeviceInfo

xsfelvis/MaterialDesignStudy: A practic

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053