/** Task to read in data received from the attached CDC device and print it to the serial port.
 */
void CDCHost_Task(void)
{
	if (USB_HostState != HOST_STATE_Configured)
	  return;

	/* Select the data IN pipe */
	Pipe_SelectPipe(CDC_DATA_IN_PIPE);
	Pipe_Unfreeze();

	/* Check to see if a packet has been received */
	if (Pipe_IsINReceived())
	{
		/* Re-freeze IN pipe after the packet has been received */
		Pipe_Freeze();

		/* Check if data is in the pipe */
		if (Pipe_IsReadWriteAllowed())
		{
			/* Get the length of the pipe data, and create a new buffer to hold it */
			uint16_t BufferLength = Pipe_BytesInPipe();
			uint8_t  Buffer[BufferLength];

			/* Read in the pipe data to the temporary buffer */
			Pipe_Read_Stream_LE(Buffer, BufferLength, NULL);

			/* Print out the buffer contents to the USART */
			for (uint16_t BufferByte = 0; BufferByte < BufferLength; BufferByte++)
			  putchar(Buffer[BufferByte]);
		}

		/* Clear the pipe after it is read, ready for the next packet */
		Pipe_ClearIN();
	}

	/* Re-freeze IN pipe after use */
	Pipe_Freeze();

	/* Select and unfreeze the notification pipe */
	Pipe_SelectPipe(CDC_NOTIFICATION_PIPE);
	Pipe_Unfreeze();

	/* Check if a packet has been received */
	if (Pipe_IsINReceived())
	{
		/* Discard the unused event notification */
		Pipe_ClearIN();
	}

	/* Freeze notification IN pipe after use */
	Pipe_Freeze();
}

/** Sends or receives the transaction's data stage to or from the attached device, reading or
 *  writing to the nominated buffer.
 *
 *  \param[in] SCSICommandBlock  Pointer to a SCSI command block structure being sent to the attached device
 *  \param[in,out]  BufferPtr    Pointer to the data buffer to read from or write to
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
static uint8_t MassStore_SendReceiveData(CommandBlockWrapper_t* const SCSICommandBlock,
                                         void* BufferPtr)
{
	uint8_t  ErrorCode = PIPE_RWSTREAM_NoError;
	uint16_t BytesRem  = SCSICommandBlock->DataTransferLength;

	/* Check the direction of the SCSI command data stage */
	if (SCSICommandBlock->Flags & COMMAND_DIRECTION_DATA_IN)
	{
		/* Wait until the device has replied with some data */
		if ((ErrorCode = MassStore_WaitForDataReceived()) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Select the IN data pipe for data reception */
		Pipe_SelectPipe(MASS_STORE_DATA_IN_PIPE);
		Pipe_Unfreeze();

		/* Read in the block data from the pipe */
		if ((ErrorCode = Pipe_Read_Stream_LE(BufferPtr, BytesRem)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Acknowledge the packet */
		Pipe_ClearIN();
	}
	else
	{
		/* Select the OUT data pipe for data transmission */
		Pipe_SelectPipe(MASS_STORE_DATA_OUT_PIPE);
		Pipe_Unfreeze();

		/* Write the block data to the pipe */
		if ((ErrorCode = Pipe_Write_Stream_LE(BufferPtr, BytesRem)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;

		/* Acknowledge the packet */
		Pipe_ClearOUT();

		while (!(Pipe_IsOUTReady()))
		{
			if (USB_HostState == HOST_STATE_Unattached)
			  return PIPE_RWSTREAM_DeviceDisconnected;
		}
	}

	/* Freeze used pipe after use */
	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}

bool Pipe_IsEndpointBound(const uint8_t EndpointAddress)
{
	uint8_t PrevPipeNumber = Pipe_GetCurrentPipe();

	for (uint8_t PNum = 0; PNum < PIPE_TOTAL_PIPES; PNum++)
	{
		Pipe_SelectPipe(PNum);
		
		if (Pipe_IsConfigured() && (Pipe_BoundEndpointNumber() == (EndpointAddress & PIPE_EPNUM_MASK)))
		  return true;
	}
	
	Pipe_SelectPipe(PrevPipeNumber);
	return false;
}

static uint8_t SImage_Host_SendBlockHeader(USB_ClassInfo_SI_Host_t* const SIInterfaceInfo, SI_PIMA_Container_t* const PIMAHeader)
{
	uint8_t ErrorCode;
	
	PIMAHeader->TransactionID = SIInterfaceInfo->State.TransactionID++;

	Pipe_SelectPipe(SIInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(PIMAHeader, PIMA_COMMAND_SIZE(0), NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;
	
	uint8_t ParamBytes = (PIMAHeader->DataLength - PIMA_COMMAND_SIZE(0));

	if (ParamBytes)
	{
		if ((ErrorCode = Pipe_Write_Stream_LE(&PIMAHeader->Params, ParamBytes, NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;
	}
	
	Pipe_ClearOUT();	
	Pipe_Freeze();
	
	return PIPE_RWSTREAM_NoError;
}

uint8_t SI_Host_SendBlockHeader(USB_ClassInfo_SI_Host_t* const SIInterfaceInfo,
                                PIMA_Container_t* const PIMAHeader)
{
	uint8_t ErrorCode;

	if ((USB_HostState != HOST_STATE_Configured) || !(SIInterfaceInfo->State.IsActive))
	  return PIPE_RWSTREAM_DeviceDisconnected;

	if (SIInterfaceInfo->State.IsSessionOpen)
	  PIMAHeader->TransactionID = SIInterfaceInfo->State.TransactionID++;

	Pipe_SelectPipe(SIInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(PIMAHeader, PIMA_COMMAND_SIZE(0), NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	uint8_t ParamBytes = (PIMAHeader->DataLength - PIMA_COMMAND_SIZE(0));

	if (ParamBytes)
	{
		if ((ErrorCode = Pipe_Write_Stream_LE(&PIMAHeader->Params, ParamBytes, NO_STREAM_CALLBACK)) != PIPE_RWSTREAM_NoError)
		  return ErrorCode;
	}

	Pipe_ClearOUT();
	Pipe_Freeze();

	return PIPE_RWSTREAM_NoError;
}

void CDC_Host_USBTask(USB_ClassInfo_CDC_Host_t* const CDCInterfaceInfo)
{
	if ((USB_HostState != HOST_STATE_Configured) || !(CDCInterfaceInfo->State.IsActive))
	  return;
	
	Pipe_SelectPipe(CDCInterfaceInfo->Config.NotificationPipeNumber);
	Pipe_SetPipeToken(PIPE_TOKEN_IN);
	Pipe_Unfreeze();

	if (Pipe_IsINReceived())
	{
		USB_Request_Header_t Notification;
		Pipe_Read_Stream_LE(&Notification, sizeof(USB_Request_Header_t), NO_STREAM_CALLBACK);
		
		if ((Notification.bRequest      == NOTIF_SerialState) &&
		    (Notification.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE)))
		{
			Pipe_Read_Stream_LE(&CDCInterfaceInfo->State.ControlLineStates.DeviceToHost,
			                    sizeof(CDCInterfaceInfo->State.ControlLineStates.DeviceToHost),
			                    NO_STREAM_CALLBACK);
			
		}

		Pipe_ClearIN();

		EVENT_CDC_Host_ControLineStateChanged(CDCInterfaceInfo);
	}
	
	Pipe_Freeze();
}

bool MIDI_Host_ReceiveEventPacket(USB_ClassInfo_MIDI_Host_t* const MIDIInterfaceInfo,
                                  MIDI_EventPacket_t* const Event)
{
	if ((USB_HostState != HOST_STATE_Configured) || !(MIDIInterfaceInfo->State.IsActive))
	  return HOST_SENDCONTROL_DeviceDisconnected;

	bool DataReady = false;

	Pipe_SelectPipe(MIDIInterfaceInfo->Config.DataINPipe.Address);
	Pipe_Unfreeze();

	if (Pipe_IsINReceived())
	{
		if (Pipe_BytesInPipe())
		{
			Pipe_Read_Stream_LE(Event, sizeof(MIDI_EventPacket_t), NULL);
			DataReady = true;
		}

		if (!(Pipe_BytesInPipe()))
		  Pipe_ClearIN();
	}

	Pipe_Freeze();

	return DataReady;
}

static uint8_t Bluetooth_SendHCICommand(void* Parameters, uint16_t ParameterLength)
{
	/* Need to reserve the amount of bytes given in the header for the complete payload */
	uint8_t CommandBuffer[sizeof(HCICommandHeader) + HCICommandHeader.ParameterLength];

	USB_ControlRequest = (USB_Request_Header_t)
		{
			.bmRequestType = (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_DEVICE),
			.bRequest      = 0,
			.wValue        = 0,
			.wIndex        = 0,
			.wLength       = sizeof(CommandBuffer)
		};

	/* Copy over the HCI command header to the allocated buffer */
	memcpy(CommandBuffer, &HCICommandHeader, sizeof(HCICommandHeader));
	
	/* Zero out the parameter section of the response to ensure that any padding bytes do not expose private RAM contents */
	memset(&CommandBuffer[sizeof(HCICommandHeader)], 0x00, HCICommandHeader.ParameterLength);

	/* Copy over the command parameters (if any) to the command buffer - note, the number of actual source parameter bytes
	   may differ to those in the header; any difference in length is filled with 0x00 padding bytes */
	memcpy(&CommandBuffer[sizeof(HCICommandHeader)], Parameters, ParameterLength);
	
	Pipe_SelectPipe(PIPE_CONTROLPIPE);
	return USB_Host_SendControlRequest(CommandBuffer);
}

/** Routine to send the current CBW to the device, and increment the Tag value as needed.
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum
 */
static uint8_t MassStore_SendCommand(void)
{
	uint8_t ErrorCode = PIPE_RWSTREAM_NoError;

	/* Each transmission should have a unique tag value, excluding values 0 and 0xFFFFFFFF */
	if (++MassStore_Tag == 0xFFFFFFFF)
	  MassStore_Tag = 1;

	/* Select the OUT data pipe for CBW transmission */
	Pipe_SelectPipe(MASS_STORE_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	/* Write the CBW command to the OUT pipe */
	if ((ErrorCode = Pipe_Write_Stream_LE(&SCSICommandBlock, sizeof(CommandBlockWrapper_t))) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	/* Send the data in the OUT pipe to the attached device */
	Pipe_ClearOUT();
	
	while(!(Pipe_IsOUTReady()));

	/* Freeze pipe after use */
	Pipe_Freeze();
	
	return PIPE_RWSTREAM_NoError;
}

static uint8_t MS_Host_GetReturnedStatus(USB_ClassInfo_MS_Host_t* const MSInterfaceInfo,
                                         MS_CommandStatusWrapper_t* const SCSICommandStatus)
{
	uint8_t ErrorCode = PIPE_RWSTREAM_NoError;

	if ((ErrorCode = MS_Host_WaitForDataReceived(MSInterfaceInfo)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	Pipe_SelectPipe(MSInterfaceInfo->Config.DataINPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Read_Stream_LE(SCSICommandStatus, sizeof(MS_CommandStatusWrapper_t),
	                                     NULL)) != PIPE_RWSTREAM_NoError)
	{
		return ErrorCode;
	}

	Pipe_ClearIN();
	Pipe_Freeze();

	if (SCSICommandStatus->Status != MS_SCSI_COMMAND_Pass)
	  ErrorCode = MS_ERROR_LOGICAL_CMD_FAILED;

	return ErrorCode;
}

static uint8_t MS_Host_SendCommand(USB_ClassInfo_MS_Host_t* const MSInterfaceInfo,
                                   MS_CommandBlockWrapper_t* const SCSICommandBlock,
                                   const void* const BufferPtr)
{
	uint8_t ErrorCode = PIPE_RWSTREAM_NoError;

	SCSICommandBlock->Signature = MS_CBW_SIGNATURE;
	SCSICommandBlock->Tag       = ++MSInterfaceInfo->State.TransactionTag;

	if (MSInterfaceInfo->State.TransactionTag == 0xFFFFFFFF)
	  MSInterfaceInfo->State.TransactionTag = 1;

	Pipe_SelectPipe(MSInterfaceInfo->Config.DataOUTPipeNumber);
	Pipe_Unfreeze();

	if ((ErrorCode = Pipe_Write_Stream_LE(SCSICommandBlock, sizeof(MS_CommandBlockWrapper_t),
	                                      NULL)) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	Pipe_ClearOUT();
	Pipe_WaitUntilReady();

	Pipe_Freeze();

	if ((BufferPtr != NULL) &&
	    ((ErrorCode = MS_Host_SendReceiveData(MSInterfaceInfo, SCSICommandBlock, (void*)BufferPtr)) != PIPE_RWSTREAM_NoError))
	{
		Pipe_Freeze();
		return ErrorCode;
	}

	return ErrorCode;
}

/** ISR to handle the reloading of the PWM timer with the next sample. */
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
{
	uint8_t PrevPipe = Pipe_GetCurrentPipe();

	/* Check that the USB bus is ready for the next sample to write */
	if (Audio_Host_IsReadyForNextSample(&Speaker_Audio_Interface))
	{
		int16_t AudioSample;

		#if defined(USE_TEST_TONE)
			static uint8_t SquareWaveSampleCount;
			static int16_t CurrentWaveValue;
			
			/* In test tone mode, generate a square wave at 1/256 of the sample rate */
			if (SquareWaveSampleCount++ == 0xFF)
			  CurrentWaveValue ^= 0x8000;
			
			/* Only generate audio if the board button is being pressed */
			AudioSample = (Buttons_GetStatus() & BUTTONS_BUTTON1) ? CurrentWaveValue : 0;
		#else
			/* Audio sample is ADC value scaled to fit the entire range */
			AudioSample = ((SAMPLE_MAX_RANGE / ADC_MAX_RANGE) * ADC_GetResult());

			#if defined(MICROPHONE_BIASED_TO_HALF_RAIL)
			/* Microphone is biased to half rail voltage, subtract the bias from the sample value */
			AudioSample -= (SAMPLE_MAX_RANGE / 2);
			#endif
		#endif
		
		Audio_Host_WriteSample16(&Speaker_Audio_Interface, AudioSample);	
		Audio_Host_WriteSample16(&Speaker_Audio_Interface, AudioSample);
	}
	
	Pipe_SelectPipe(PrevPipe);
}

static uint8_t Bluetooth_SendHCICommand(void* Parameters, uint8_t ParamLength)
{
	uint8_t CommandBuffer[sizeof(HCICommandHeader) + HCICommandHeader.ParameterLength];

	USB_HostRequest = (USB_Host_Request_Header_t)
		{
			bmRequestType: (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_DEVICE),
			bRequest:      0,
			wValue:        0,
			wIndex:        0,
			wLength:       sizeof(CommandBuffer)
		};
		
	memset(CommandBuffer, 0x00, sizeof(CommandBuffer));
	memcpy(CommandBuffer, &HCICommandHeader, sizeof(HCICommandHeader));
	
	if (ParamLength)
	  memcpy(&CommandBuffer[sizeof(HCICommandHeader)], Parameters, ParamLength);

	return USB_Host_SendControlRequest(CommandBuffer);
}

static bool Bluetooth_GetNextHCIEventHeader(void)
{
	Pipe_SelectPipe(BLUETOOTH_EVENTS_PIPE);
	Pipe_Unfreeze();
	
	if (!(Pipe_ReadWriteAllowed()))
	  return false;
	  
	Pipe_Read_Stream_LE(&HCIEventHeader, sizeof(HCIEventHeader));
	  
	return true;
}

uint8_t MIDI_Host_Flush(USB_ClassInfo_MIDI_Host_t* const MIDIInterfaceInfo)
{
	if ((USB_HostState != HOST_STATE_Configured) || !(MIDIInterfaceInfo->State.IsActive))
	  return PIPE_RWSTREAM_DeviceDisconnected;

	uint8_t ErrorCode;

	Pipe_SelectPipe(MIDIInterfaceInfo->Config.DataOUTPipe.Address);
	Pipe_Unfreeze();

	if (Pipe_BytesInPipe())
	{
		Pipe_ClearOUT();

		if ((ErrorCode = Pipe_WaitUntilReady()) != PIPE_READYWAIT_NoError)
		{
			Pipe_Freeze();
			return ErrorCode;
		}
	}

	Pipe_Freeze();

	return PIPE_READYWAIT_NoError;
}

/** Function to send the PIMA command container to the attached still image device. */
void SImage_SendBlockHeader(void)
{
	/* Unfreeze the data OUT pipe ready for data transmission */
	Pipe_SelectPipe(SIMAGE_DATA_OUT_PIPE);
	Pipe_Unfreeze();

	/* Write the PIMA block to the data OUT pipe */
	Pipe_Write_Stream_LE(&PIMA_SendBlock, PIMA_COMMAND_SIZE(0), NULL);

	/* If the block type is a command, send its parameters (if any) */
	if (PIMA_SendBlock.Type == PIMA_CONTAINER_CommandBlock)
	{
		/* Determine the size of the parameters in the block via the data length attribute */
		uint8_t ParamBytes = (PIMA_SendBlock.DataLength - PIMA_COMMAND_SIZE(0));

		/* Check if any parameters in the command block */
		if (ParamBytes)
		{
			/* Write the PIMA parameters to the data OUT pipe */
			Pipe_Write_Stream_LE(&PIMA_SendBlock.Params, ParamBytes, NULL);
		}

		/* Send the PIMA command block to the attached device */
		Pipe_ClearOUT();
	}

	/* Freeze pipe after use */
	Pipe_Freeze();
}

/** Routine to receive the current CSW from the device.
 *
 *  \param[out] SCSICommandStatus  Pointer to a destination where the returned status data should be stored
 *
 *  \return A value from the Pipe_Stream_RW_ErrorCodes_t enum, or MASS_STORE_SCSI_COMMAND_FAILED if the SCSI command fails
 */
static uint8_t MassStore_GetReturnedStatus(CommandStatusWrapper_t* const SCSICommandStatus)
{
	uint8_t ErrorCode = PIPE_RWSTREAM_NoError;

	/* If an error in the command occurred, abort */
	if ((ErrorCode = MassStore_WaitForDataReceived()) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	/* Select the IN data pipe for data reception */
	Pipe_SelectPipe(MASS_STORE_DATA_IN_PIPE);
	Pipe_Unfreeze();

	/* Load in the CSW from the attached device */
	if ((ErrorCode = Pipe_Read_Stream_LE(SCSICommandStatus, sizeof(CommandStatusWrapper_t))) != PIPE_RWSTREAM_NoError)
	  return ErrorCode;

	/* Clear the data ready for next reception */
	Pipe_ClearIN();

	/* Freeze the IN pipe after use */
	Pipe_Freeze();

	/* Check to see if command failed */
	if (SCSICommandStatus->Status != Command_Pass)
	  ErrorCode = MASS_STORE_SCSI_COMMAND_FAILED;

	return ErrorCode;
}

/** Task to read and process the HID report descriptor and HID reports from the device and display the
 *  results onto the board LEDs.
 */
void MouseHost_Task(void)
{
	if (USB_HostState != HOST_STATE_Configured)
	  return;

	/* Select and unfreeze mouse data pipe */
	Pipe_SelectPipe(MOUSE_DATA_IN_PIPE);
	Pipe_Unfreeze();

	/* Check to see if a packet has been received */
	if (Pipe_IsINReceived())
	{
		/* Check if data has been received from the attached mouse */
		if (Pipe_IsReadWriteAllowed())
		{
			/* Create buffer big enough for the report */
			uint8_t MouseReport[Pipe_BytesInPipe()];

			/* Load in the mouse report */
			Pipe_Read_Stream_LE(MouseReport, Pipe_BytesInPipe(), NULL);

			/* Process the read in mouse report from the device */
			ProcessMouseReport(MouseReport);
		}

		/* Clear the IN endpoint, ready for next data packet */
		Pipe_ClearIN();
	}

	/* Freeze mouse data pipe */
	Pipe_Freeze();
}

/** Reads in and processes the next report from the attached device, displaying the report
 *  contents on the board LEDs and via the serial port.
 */
void ReadNextReport(void)
{
	USB_MouseReport_Data_t MouseReport;
	uint8_t                LEDMask = LEDS_NO_LEDS;

	/* Select mouse data pipe */
	Pipe_SelectPipe(MOUSE_DATA_IN_PIPE);

	/* Unfreeze keyboard data pipe */
	Pipe_Unfreeze();

	/* Check to see if a packet has been received */
	if (!(Pipe_IsINReceived()))
	{
		/* No packet received (no movement), turn off LEDs */
		LEDs_SetAllLEDs(LEDS_NO_LEDS);

		/* Refreeze HID data IN pipe */
		Pipe_Freeze();

		return;
	}

	/* Ensure pipe contains data before trying to read from it */
	if (Pipe_IsReadWriteAllowed())
	{
		/* Read in mouse report data */
		Pipe_Read_Stream_LE(&MouseReport, sizeof(MouseReport));

		/* Alter status LEDs according to mouse X movement */
		if (MouseReport.X > 0)
		  LEDMask |= LEDS_LED1;
		else if (MouseReport.X < 0)
		  LEDMask |= LEDS_LED2;

		/* Alter status LEDs according to mouse Y movement */
		if (MouseReport.Y > 0)
		  LEDMask |= LEDS_LED3;
		else if (MouseReport.Y < 0)
		  LEDMask |= LEDS_LED4;

		/* Alter status LEDs according to mouse button position */
		if (MouseReport.Button)
		  LEDMask  = LEDS_ALL_LEDS;

		LEDs_SetAllLEDs(LEDMask);

		/* Print mouse report data through the serial port */
		printf_P(PSTR("dX:%2d dY:%2d Button:%d\r\n"), MouseReport.X,
													  MouseReport.Y,
													  MouseReport.Button);
	}

	/* Clear the IN endpoint, ready for next data packet */
	Pipe_ClearIN();

	/* Refreeze mouse data pipe */
	Pipe_Freeze();
}

/** Reads in and processes the next report from the attached device, displaying the report
 *  contents on the board LEDs and via the serial port.
 */
void ReadNextReport(void)
{
	USB_KeyboardReport_Data_t KeyboardReport;
		
	/* Select keyboard data pipe */
	Pipe_SelectPipe(KEYBOARD_DATAPIPE);	

	/* Unfreeze keyboard data pipe */
	Pipe_Unfreeze();

	/* Check to see if a packet has been received */
	if (!(Pipe_IsINReceived()))
	{
		/* Refreeze HID data IN pipe */
		Pipe_Freeze();
			
		return;
	}
	
	/* Ensure pipe contains data before trying to read from it */
	if (Pipe_IsReadWriteAllowed())
	{
		/* Read in keyboard report data */
		Pipe_Read_Stream_LE(&KeyboardReport, sizeof(KeyboardReport));

		/* Indicate if the modifier byte is non-zero (special key such as shift is being pressed) */
		LEDs_ChangeLEDs(LEDS_LED1, (KeyboardReport.Modifier) ? LEDS_LED1 : 0);
		
		/* Check if a key has been pressed */
		if (KeyboardReport.KeyCode)
		{
			/* Toggle status LED to indicate keypress */
			LEDs_ToggleLEDs(LEDS_LED2);
				  
			char PressedKey = 0;

			/* Retrieve pressed key character if alphanumeric */
			if ((KeyboardReport.KeyCode[0] >= 0x04) && (KeyboardReport.KeyCode[0] <= 0x1D))
			  PressedKey = (KeyboardReport.KeyCode[0] - 0x04) + 'A';
			else if ((KeyboardReport.KeyCode[0] >= 0x1E) && (KeyboardReport.KeyCode[0] <= 0x27))
			  PressedKey = (KeyboardReport.KeyCode[0] - 0x1E) + '0';
			else if (KeyboardReport.KeyCode[0] == 0x2C)
			  PressedKey = ' ';						
			else if (KeyboardReport.KeyCode[0] == 0x28)
			  PressedKey = '\n';
				 
			/* Print the pressed key character out through the serial port if valid */
			if (PressedKey)
			  putchar(PressedKey);
		}
	}
		
	/* Clear the IN endpoint, ready for next data packet */
	Pipe_ClearIN();

	/* Refreeze keyboard data pipe */
	Pipe_Freeze();
}

bool Pipe_IsEndpointBound(const uint8_t EndpointAddress)
{
	uint8_t PrevPipeNumber = Pipe_GetCurrentPipe();

	for (uint8_t PNum = 0; PNum < PIPE_TOTAL_PIPES; PNum++)
	{
		Pipe_SelectPipe(PNum);

		if (!(Pipe_IsConfigured()))
		  continue;

		if (Pipe_GetBoundEndpointAddress() == EndpointAddress)
		  return true;
	}

	Pipe_SelectPipe(PrevPipeNumber);
	return false;
}