C++ HAL_TIM_PWM_Start函数代码示例

OStack程序员社区-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中HAL_TIM_PWM_Start函数的典型用法代码示例。如果您正苦于以下问题：C++ HAL_TIM_PWM_Start函数的具体用法？C++ HAL_TIM_PWM_Start怎么用？C++ HAL_TIM_PWM_Start使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了HAL_TIM_PWM_Start函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: main

int main(void)
{
    /* -1- Init System*/
    HAL_Init();
    SystemClock_Config();
    /* -2- Calculate Prescaler */
    //We want the Timer to run with 8MHz (the maximum, since we're running of the internal Clock, which runs at 8MHz, without PLL)
    uhPrescalerValue = (uint32_t) (SystemCoreClock / 8000000) - 1;

    /* -3- Enable Clocks*/
    //GPIO
    __GPIOA_CLK_ENABLE();
    //TIMER
    __TIM1_CLK_ENABLE();

    /* -4- Configure GPIO Pin*/
    GPIO_InitStruct.Pin = GPIO_PIN_10;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
    GPIO_InitStruct.Alternate = GPIO_AF2_TIM1;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

    /* -5- Configure Timer*/
    TIM_HandleStruct.Instance = TIM1;
    TIM_HandleStruct.Init.Prescaler = uhPrescalerValue;
    TIM_HandleStruct.Init.Period = PERIOD_VALUE;
    TIM_HandleStruct.Init.ClockDivision = 0;
    TIM_HandleStruct.Init.CounterMode = TIM_COUNTERMODE_UP;
    TIM_HandleStruct.Init.RepetitionCounter = 0;
    HAL_TIM_PWM_Init(&TIM_HandleStruct);

    /* -6- Configure PWM-Output*/
    TIM_OC_InitStruct.OCMode = TIM_OCMODE_PWM1;
    TIM_OC_InitStruct.OCPolarity = TIM_OCPOLARITY_HIGH;
    TIM_OC_InitStruct.OCFastMode = TIM_OCFAST_DISABLE;
    TIM_OC_InitStruct.OCNPolarity = TIM_OCNPOLARITY_HIGH;
    TIM_OC_InitStruct.OCIdleState = TIM_OCIDLESTATE_RESET;
    TIM_OC_InitStruct.OCNIdleState = TIM_OCNIDLESTATE_RESET;
    TIM_OC_InitStruct.Pulse = CMP_VAL;
    HAL_TIM_PWM_ConfigChannel(&TIM_HandleStruct, &TIM_OC_InitStruct, TIM_CHANNEL_3);

    /* -7- Enable Timer and PWM Output*/
    HAL_TIM_PWM_Start(&TIM_HandleStruct, TIM_CHANNEL_3);

    while (1) {
        /* -8- Illuminate LED*/
        for (CMP_VAL = 0; CMP_VAL != (PERIOD_VALUE); CMP_VAL++) {
            TIM_OC_InitStruct.Pulse = CMP_VAL;
            HAL_TIM_PWM_ConfigChannel(&TIM_HandleStruct, &TIM_OC_InitStruct, TIM_CHANNEL_3);
            HAL_TIM_PWM_Start(&TIM_HandleStruct, TIM_CHANNEL_3);
            HAL_Delay(1);
        }
        /* -8- Wait a bit at full brightness*/
        HAL_Delay(1000);
        /* -10- Dim LED*/
        for (CMP_VAL = (PERIOD_VALUE); CMP_VAL != 0; CMP_VAL--) {
            TIM_OC_InitStruct.Pulse = CMP_VAL;
            HAL_TIM_PWM_ConfigChannel(&TIM_HandleStruct, &TIM_OC_InitStruct, TIM_CHANNEL_3);
            HAL_TIM_PWM_Start(&TIM_HandleStruct, TIM_CHANNEL_3);
            HAL_Delay(1);
        }
        /* -11- Leave it dark*/
        HAL_Delay(1000);
    }
}

开发者ID:glocklueng，项目名称:stm32f030f4-Projects，代码行数:66，代码来源:main.c

示例2: main


//.........这里部分代码省略.........
  Timer clock prescalers selection activated (TIMPRE bit from RCC_DCKCFGR register is set).   
  TIM3CLK = 4 * PCLK1  
  PCLK1 = HCLK / 4 
  => TIM3CLK = HCLK = SystemCoreClock

  For TIM3CLK equal to SystemCoreClock and prescaler equal to (5 - 1), TIM3 counter clock 
  is computed as follows:
  TIM3 counter clock = TIM3CLK / (Prescaler + 1)
                     = SystemCoreClock / (Prescaler + 1)
                     = 36MHz

  For ARR equal to (1800 - 1), the TIM3 output clock is computed as follows:
  TIM3 output clock = TIM3 counter clock / (ARR + 1)
                    = 20KHZ
                     
  The TIM3 CCR1 register value is equal to 900, so the TIM3 Channel 1 generates a 
  PWM signal with a frequency equal to 20 KHz and a duty cycle equal to 50%:

  TIM3 Channel1 duty cycle = (TIM3_CCR1/ TIM3_ARR + 1)* 100 = 50%

    Note:
     SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f4xx.c file.
     Each time the core clock (HCLK) changes, user had to update SystemCoreClock
     variable value. Otherwise, any configuration based on this variable will be incorrect.
     This variable is updated in three ways:
      1) by calling CMSIS function SystemCoreClockUpdate()
      2) by calling HAL API function HAL_RCC_GetSysClockFreq()
      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
  ----------------------------------------------------------------------- */

  /* Timer clock prescalers selection activation */ 
  __HAL_RCC_TIMCLKPRESCALER(RCC_TIMPRES_ACTIVATED);

  /* Initialize TIMx peripheral as follows:
       + Prescaler = (SystemCoreClock / 36000000) - 1
       + Period = (1800 - 1)
       + ClockDivision = 0
       + Counter direction = Up
  */
  TimHandle.Instance = TIMx;

  TimHandle.Init.Prescaler         = uhPrescalerValue;
  TimHandle.Init.Period            = PERIOD_VALUE;
  TimHandle.Init.ClockDivision     = 0;
  TimHandle.Init.CounterMode       = TIM_COUNTERMODE_UP;
  TimHandle.Init.RepetitionCounter = 0;
  if (HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

  /*##-2- Configure the PWM channels #########################################*/
  /* Common configuration for all channels */
  sConfig.OCMode       = TIM_OCMODE_PWM1;
  sConfig.OCPolarity   = TIM_OCPOLARITY_HIGH;
  sConfig.OCFastMode   = TIM_OCFAST_DISABLE;
  sConfig.OCNPolarity  = TIM_OCNPOLARITY_HIGH;
  sConfig.OCNIdleState = TIM_OCNIDLESTATE_RESET;
  sConfig.OCIdleState  = TIM_OCIDLESTATE_RESET;

  /* Set the pulse value for channel 1 */
  sConfig.Pulse = PULSE1_VALUE;
  if (HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /*##-3- Start PWM signals generation #######################################*/ 
  /* Start channel 1 */
  if (HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 2 */
  if (HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 3 */
  if (HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
  {
    /* PWM generation Error */
    Error_Handler();
  }
  /* Start channel 4 */
  if (HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_4) != HAL_OK)
  {
    /* PWM generation Error */
    Error_Handler();
  }

  while (1)
  {
  }

}

开发者ID:eemei，项目名称:library-stm32f4，代码行数:101，代码来源:main.c

示例3: main


//.........这里部分代码省略.........
    TIM3 Channel3 duty cycle = (TIM3_CCR3/ TIM3_ARR)* 100 = 25%
    TIM3 Channel4 duty cycle = (TIM3_CCR4/ TIM3_ARR)* 100 = 12.5%
  
    Note: 
     SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f3xx.c file.
     Each time the core clock (HCLK) changes, user had to update SystemCoreClock 
     variable value. Otherwise, any configuration based on this variable will be incorrect.
     This variable is updated in three ways:
      1) by calling CMSIS function SystemCoreClockUpdate()
      2) by calling HAL API function HAL_RCC_GetSysClockFreq()
      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency     
  ----------------------------------------------------------------------- */ 
   
  /* Initialize TIMx peripheral as follows:
       + Prescaler = (SystemCoreClock/24000000) - 1
       + Period = 665
       + ClockDivision = 0
       + Counter direction = Up
  */
  TimHandle.Instance = TIMx;
  
  TimHandle.Init.Prescaler = uhPrescalerValue;
  TimHandle.Init.Period = PERIOD_VALUE;
  TimHandle.Init.ClockDivision = 0;
  TimHandle.Init.CounterMode = TIM_COUNTERMODE_UP;
  if(HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /*##-2- Configure the PWM channels #########################################*/ 
  /* Common configuration for all channels */
  sConfig.OCMode = TIM_OCMODE_PWM1;
  sConfig.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfig.OCFastMode = TIM_OCFAST_DISABLE;

  /* Set the pulse value for channel 1 */
  sConfig.Pulse = PULSE1_VALUE;  
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /* Set the pulse value for channel 2 */
  sConfig.Pulse = PULSE2_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_2) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /* Set the pulse value for channel 3 */
  sConfig.Pulse = PULSE3_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_3) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /* Set the pulse value for channel 4 */
  sConfig.Pulse = PULSE4_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_4) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /*##-3- Start PWM signals generation #######################################*/ 
  /* Start channel 1 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 2 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 3 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 4 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_4) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }

  while (1)
  {
  }

}

开发者ID:afconsult-south，项目名称:dragonfly-fcb，代码行数:101，代码来源:main.c

示例4: HAL_SYSTICK_Callback

/**
  * @brief  SYSTICK callback.
  * @param  None
  * @retval None
  */
void HAL_SYSTICK_Callback(void)
{
    uint8_t *buf;
    uint16_t Temp_X, Temp_Y = 0x00;
    uint16_t NewARR_X, NewARR_Y = 0x00;

    if (DemoEnterCondition != 0x00)
    {
        buf = USBD_HID_GetPos();
        if((buf[1] != 0) ||(buf[2] != 0))
        {
            USBD_HID_SendReport (&hUSBDDevice,
                                 buf,
                                 4);
        }
        Counter ++;
        if (Counter == 10)
        {
            /* Reset Buffer used to get accelerometer values */
            Buffer[0] = 0;
            Buffer[1] = 0;

            /* Disable All TIM4 Capture Compare Channels */
            HAL_TIM_PWM_Stop(&htim4, TIM_CHANNEL_1);
            HAL_TIM_PWM_Stop(&htim4, TIM_CHANNEL_2);
            HAL_TIM_PWM_Stop(&htim4, TIM_CHANNEL_3);
            HAL_TIM_PWM_Stop(&htim4, TIM_CHANNEL_4);

            /* Read Acceleration*/
            BSP_ACCELERO_GetXYZ(Buffer);

            /* Set X and Y positions */
            X_Offset = Buffer[0];
            Y_Offset = Buffer[1];

            /* Update New autoreload value in case of X or Y acceleration*/
            /* Basic acceleration X_Offset and Y_Offset are divide by 40 to fir with ARR range */
            NewARR_X = TIM_ARR - ABS(X_Offset/40);
            NewARR_Y = TIM_ARR - ABS(Y_Offset/40);

            /* Calculation of Max acceleration detected on X or Y axis */
            Temp_X = ABS(X_Offset/40);
            Temp_Y = ABS(Y_Offset/40);
            MaxAcceleration = MAX_AB(Temp_X, Temp_Y);

            if(MaxAcceleration != 0)
            {

                /* Reset CNT to a lowest value (equal to min CCRx of all Channels) */
                __HAL_TIM_SET_COUNTER(&htim4,(TIM_ARR-MaxAcceleration)/2);

                if (X_Offset < ThreadholdAcceleroLow)
                {

                    /* Sets the TIM4 Capture Compare for Channel1 Register value */
                    /* Equal to NewARR_X/2 to have duty cycle equal to 50% */
                    __HAL_TIM_SET_COMPARE(&htim4, TIM_CHANNEL_1, NewARR_X/2);

                    /* Time base configuration */
                    __HAL_TIM_SET_AUTORELOAD(&htim4, NewARR_X);

                    /* Enable TIM4 Capture Compare Channel1 */
                    HAL_TIM_PWM_Start(&htim4, TIM_CHANNEL_1);

                }
                else if (X_Offset > ThreadholdAcceleroHigh)
                {

                    /* Sets the TIM4 Capture Compare for Channel3 Register value */
                    /* Equal to NewARR_X/2 to have duty cycle equal to 50% */
                    __HAL_TIM_SET_COMPARE(&htim4, TIM_CHANNEL_3, NewARR_X/2);

                    /* Time base configuration */
                    __HAL_TIM_SET_AUTORELOAD(&htim4, NewARR_X);

                    /* Enable TIM4 Capture Compare Channel3 */
                    HAL_TIM_PWM_Start(&htim4, TIM_CHANNEL_3);

                }
                if (Y_Offset > ThreadholdAcceleroHigh)
                {

                    /* Sets the TIM4 Capture Compare for Channel2 Register value */
                    /* Equal to NewARR_Y/2 to have duty cycle equal to 50% */
                    __HAL_TIM_SET_COMPARE(&htim4, TIM_CHANNEL_2,NewARR_Y/2);

                    /* Time base configuration */
                    __HAL_TIM_SET_AUTORELOAD(&htim4, NewARR_Y);

                    /* Enable TIM4 Capture Compare Channel2 */
                    HAL_TIM_PWM_Start(&htim4, TIM_CHANNEL_2);

                }
                else if (Y_Offset < ThreadholdAcceleroLow)
                {
//.........这里部分代码省略.........

开发者ID:PaxInstruments，项目名称:STM32CubeF4，代码行数:101，代码来源:main.c

示例5: MOTOR_Init

/**
 * @brief  Configures IOs to control the two motors and one pump
 * @param  None
 * @retval None
 */
void MOTOR_Init(void) {
	GPIO_InitTypeDef GPIO_InitStruct;

	// Enable all timers
	PUMP_PWM_TIMER_CLK_ENABLE();
	MOTOR_PWM_TIMER_CLK_ENABLE();
	MOTOR_HALL_ENC1_TIMER_CLK_ENABLE();
	MOTOR_HALL_ENC2_TIMER_CLK_ENABLE();
	MOTOR_HALL_SPEED_TIMER_CLK_ENABLE();


	// Enable the clock for all IO pins
	MOTOR_PWM_CLK_ENABLE();
	MOTOR_CURR_CLK_ENABLE();
	MOTOR_HALL_M1_ENC_CLK_ENABLE();
	MOTOR_HALL_M2_ENC_CLK_ENABLE();
	MOTOR_HALL_SPEED_CLK_ENABLE();

	// Motor driver --------------------------------------------------------

	// Configure the 4 motor pins of motor 1 and 2 as normal IO
	GPIO_InitStruct.Pin = MOTOR_M2_IN1_PIN | MOTOR_M2_IN2_PIN
						| MOTOR_M1_IN1_PIN| MOTOR_M1_IN2_PIN;
	GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
	GPIO_InitStruct.Pull = GPIO_NOPULL;
	GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
	GPIO_InitStruct.Alternate = MOTOR_PWM_TIMER_AF;
	HAL_GPIO_Init(MOTOR_PWM_PORT, &GPIO_InitStruct);

	// Configure the 2 motor pins of motor 3 as PWM output
	GPIO_InitStruct.Pin = MOTOR_M3_IN1_PIN | MOTOR_M3_IN2_PIN;
	GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
	GPIO_InitStruct.Pull = GPIO_NOPULL;
	GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
	GPIO_InitStruct.Alternate = PUMP_PWM_TIMER_AF;
	HAL_GPIO_Init(MOTOR_PWM_PORT, &GPIO_InitStruct);

	// Configure the 10 motor current pins
	GPIO_InitStruct.Pin = MOTOR_M2_I0_PIN | MOTOR_M2_I1_PIN | MOTOR_M2_I2_PIN
						| MOTOR_M2_I3_PIN | MOTOR_M2_I4_PIN
						| MOTOR_M1_I0_PIN | MOTOR_M1_I1_PIN | MOTOR_M1_I2_PIN
						| MOTOR_M1_I3_PIN | MOTOR_M1_I4_PIN;
	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
	GPIO_InitStruct.Pull = GPIO_NOPULL;
	GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
	HAL_GPIO_Init(MOTOR_CURR_PORT, &GPIO_InitStruct);

    // Timer configuration for motor pwm
	htimMotor.Instance = MOTOR_PWM_TIMER;
	htimMotor.Init.Period = MOTOR_MAX - 1; // = 20kHz = 84MHz / 1 / 4200
	htimMotor.Init.Prescaler = 1-1;
	htimMotor.Init.ClockDivision = 1;
	htimMotor.Init.CounterMode = TIM_COUNTERMODE_UP;
    HAL_TIM_PWM_Init(&htimMotor);

    // Timer configuration for pump
	htimPump.Instance = PUMP_PWM_TIMER;
	htimPump.Init.Period = MOTOR_MAX - 1; // = 20kHz = 168MHz / 2 / 4200
	htimPump.Init.Prescaler = 2-1;
	htimPump.Init.ClockDivision = 1;
	htimPump.Init.CounterMode = TIM_COUNTERMODE_UP;
    HAL_TIM_PWM_Init(&htimPump);

    // Configure Timer 1 channel 1 and 2 as PWM output
    sConfigTimMotor.OCMode = TIM_OCMODE_PWM1;
    sConfigTimMotor.Pulse = 0;
    sConfigTimMotor.OCPolarity = TIM_OCPOLARITY_HIGH;
    sConfigTimMotor.OCFastMode  = TIM_OCFAST_ENABLE;
    sConfigTimMotor.OCNPolarity = TIM_OCNPOLARITY_HIGH;
    sConfigTimMotor.OCIdleState = TIM_OCIDLESTATE_RESET;
    sConfigTimMotor.OCNIdleState= TIM_OCNIDLESTATE_SET;

    // Configure Timer 1 channel 1 as PWM output
    sConfigTimPump.OCMode = TIM_OCMODE_PWM1;
    sConfigTimPump.Pulse = 0;
    sConfigTimPump.OCPolarity = TIM_OCPOLARITY_HIGH;
    sConfigTimPump.OCFastMode  = TIM_OCFAST_ENABLE;
    sConfigTimPump.OCNPolarity = TIM_OCNPOLARITY_HIGH;
    sConfigTimPump.OCIdleState = TIM_OCIDLESTATE_RESET;
    sConfigTimPump.OCNIdleState= TIM_OCNIDLESTATE_SET;

    // PWM Mode
    HAL_TIM_PWM_ConfigChannel(&htimMotor, &sConfigTimMotor, TIM_CHANNEL_1);
    HAL_TIM_PWM_ConfigChannel(&htimMotor, &sConfigTimMotor, TIM_CHANNEL_2);
    HAL_TIM_PWM_ConfigChannel(&htimMotor, &sConfigTimMotor, TIM_CHANNEL_3);
    HAL_TIM_PWM_ConfigChannel(&htimMotor, &sConfigTimMotor, TIM_CHANNEL_4);
    HAL_TIM_PWM_ConfigChannel(&htimPump, &sConfigTimPump, TIM_CHANNEL_1);
    HAL_TIM_PWM_ConfigChannel(&htimPump, &sConfigTimPump, TIM_CHANNEL_2);
    HAL_TIM_PWM_Start(&htimMotor, TIM_CHANNEL_1);
    HAL_TIM_PWM_Start(&htimMotor, TIM_CHANNEL_2);
    HAL_TIM_PWM_Start(&htimMotor, TIM_CHANNEL_3);
    HAL_TIM_PWM_Start(&htimMotor, TIM_CHANNEL_4);
    HAL_TIM_PWM_Start(&htimPump, TIM_CHANNEL_1);
    HAL_TIM_PWM_Start(&htimPump, TIM_CHANNEL_2);

//.........这里部分代码省略.........

开发者ID:gerdb，项目名称:street-art-robot，代码行数:101，代码来源:motor.c

示例6: main


//.........这里部分代码省略.........
    TimHandle.Init.RepetitionCounter = 0;

    if(HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
    {
        /* Initialization Error */
        Error_Handler();
    }

    /*##-2- Configure the PWM channels #########################################*/
    /* Common configuration for all channels */
    sPWMConfig.OCMode       = TIM_OCMODE_PWM1;
    sPWMConfig.OCPolarity   = TIM_OCPOLARITY_HIGH;
    sPWMConfig.OCNPolarity  = TIM_OCNPOLARITY_HIGH;
    sPWMConfig.OCIdleState  = TIM_OCIDLESTATE_SET;
    sPWMConfig.OCNIdleState = TIM_OCNIDLESTATE_RESET;

    /* Set the pulse value for channel 1 */
    sPWMConfig.Pulse = PULSE1_VALUE;
    if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sPWMConfig, TIM_CHANNEL_1) != HAL_OK)
    {
        /* Configuration Error */
        Error_Handler();
    }

    /* Set the pulse value for channel 2 */
    sPWMConfig.Pulse = PULSE2_VALUE;
    if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sPWMConfig, TIM_CHANNEL_2) != HAL_OK)
    {
        /* Configuration Error */
        Error_Handler();
    }

    /* Set the pulse value for channel 3 */
    sPWMConfig.Pulse = PULSE3_VALUE;
    if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sPWMConfig, TIM_CHANNEL_3) != HAL_OK)
    {
        /* Configuration Error */
        Error_Handler();
    }

    /* Set the Break feature & Dead time */
    sBreakConfig.BreakState       = TIM_BREAK_ENABLE;
    sBreakConfig.DeadTime         = 11;
    sBreakConfig.OffStateRunMode  = TIM_OSSR_ENABLE;
    sBreakConfig.OffStateIDLEMode = TIM_OSSI_ENABLE;
    sBreakConfig.LockLevel        = TIM_LOCKLEVEL_1;
    sBreakConfig.BreakPolarity    = TIM_BREAKPOLARITY_HIGH;
    sBreakConfig.AutomaticOutput  = TIM_AUTOMATICOUTPUT_ENABLE;

    if(HAL_TIMEx_ConfigBreakDeadTime(&TimHandle, &sBreakConfig) != HAL_OK)
    {
        /* Configuration Error */
        Error_Handler();
    }

    /*##-3- Start PWM signals generation #######################################*/
    /* Start channel 1 */
    if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
    {
        /* Starting Error */
        Error_Handler();
    }
    /* Start channel 1N */
    if(HAL_TIMEx_PWMN_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
    {
        /* Starting Error */
        Error_Handler();
    }

    /* Start channel 2 */
    if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
    {
        /* Starting Error */
        Error_Handler();
    }
    /* Start channel 2N */
    if(HAL_TIMEx_PWMN_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
    {
        /* Starting Error */
        Error_Handler();
    }

    /* Start channel 3 */
    if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
    {
        /* Starting Error */
        Error_Handler();
    }
    /* Start channel 3N */
    if(HAL_TIMEx_PWMN_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
    {
        /* Starting Error */
        Error_Handler();
    }

    /* Infinite loop */
    while (1)
    {
    }
}

开发者ID:PaxInstruments，项目名称:STM32CubeF4，代码行数:101，代码来源:main.c

示例7: pwmout_write

void pwmout_write(pwmout_t* obj, float value) {
    TIM_OC_InitTypeDef sConfig;
    int channel = 0;
    int complementary_channel = 0;

    TimHandle.Instance = (TIM_TypeDef *)(obj->pwm);

    if (value < (float)0.0) {
        value = 0.0;
    } else if (value > (float)1.0) {
        value = 1.0;
    }

    obj->pulse = (uint32_t)((float)obj->period * value);

    // Configure channels
    sConfig.OCMode       = TIM_OCMODE_PWM1;
    sConfig.Pulse        = obj->pulse;
    sConfig.OCPolarity   = TIM_OCPOLARITY_HIGH;
    sConfig.OCNPolarity  = TIM_OCNPOLARITY_HIGH;
    sConfig.OCFastMode   = TIM_OCFAST_DISABLE;
    sConfig.OCIdleState  = TIM_OCIDLESTATE_RESET;
    sConfig.OCNIdleState = TIM_OCNIDLESTATE_RESET;

    switch (obj->pin) {

        // Channels 1
        case PA_0:
        case PA_5:
        case PA_6:
        case PA_8:
        case PA_15:
        case PB_4:
        case PB_6:
        case PC_6:
            channel = TIM_CHANNEL_1;
            break;

        // Channels 1N
        case PA_7:
        case PB_13:
            channel = TIM_CHANNEL_1;
            complementary_channel = 1;
            break;

        // Channels 2
        case PA_1:
        case PA_9:
        case PB_3:
        case PB_5:
        case PB_7:
        case PC_7:
            channel = TIM_CHANNEL_2;
            break;

        // Channels 2N
        case PB_0:
        case PB_14:
            channel = TIM_CHANNEL_2;
            complementary_channel = 1;
            break;

        // Channels 3
        case PA_2:
        case PA_10:
        case PB_8:
        case PB_10:
        case PC_8:
            channel = TIM_CHANNEL_3;
            break;

        // Channels 3N
        case PB_1:
        case PB_15:
            channel = TIM_CHANNEL_3;
            complementary_channel = 1;
            break;

        // Channels 4
        case PA_3:
        case PA_11:
        case PB_9:
        case PC_9:
            channel = TIM_CHANNEL_4;
            break;

        default:
            return;
    }

    HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, channel);
    if (complementary_channel) {
        HAL_TIMEx_PWMN_Start(&TimHandle, channel);
    } else {
        HAL_TIM_PWM_Start(&TimHandle, channel);
    }
}

开发者ID:mbrudevoldlpd，项目名称:mbed_rtx_issue，代码行数:97，代码来源:pwmout_api.c

示例8: main


//.........这里部分代码省略.........
    TIM3 Channel3 duty cycle = (TIM3_CCR3/ TIM3_ARR + 1)* 100 = 25%
    TIM3 Channel4 duty cycle = (TIM3_CCR4/ TIM3_ARR + 1)* 100 = 12.5%

    Note: 
     SystemCoreClock variable holds HCLK frequency and is defined in SystemClock_Config().
     Each time the core clock (HCLK) changes, user had to update SystemCoreClock 
     variable value. Otherwise, any configuration based on this variable will be incorrect.
     This variable is updated in three ways:
      1) by calling CMSIS function SystemCoreClockUpdate()
      2) by calling HAL API function HAL_RCC_GetSysClockFreq()
      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency     
  ----------------------------------------------------------------------- */ 
  
  /* Initialize TIMx peripheral as follow:
       + Prescaler = (SystemCoreClock/2)/21000000
       + Period = 665
       + ClockDivision = 0
       + Counter direction = Up
  */
  TimHandle.Instance = TIMx;
  
  TimHandle.Init.Prescaler = uhPrescalerValue;
  TimHandle.Init.Period = PERIOD_VALUE;
  TimHandle.Init.ClockDivision = 0;
  TimHandle.Init.CounterMode = TIM_COUNTERMODE_UP;
  if(HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /*##-2- Configure the PWM channels #########################################*/ 
  /* Common configuration for all channels */
  sConfig.OCMode = TIM_OCMODE_PWM1;
  sConfig.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfig.OCFastMode = TIM_OCFAST_DISABLE;

  /* Set the pulse value for channel 1 */
  sConfig.Pulse = PULSE1_VALUE;  
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /* Set the pulse value for channel 2 */
  sConfig.Pulse = PULSE2_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_2) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /* Set the pulse value for channel 3 */
  sConfig.Pulse = PULSE3_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_3) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /* Set the pulse value for channel 4 */
  sConfig.Pulse = PULSE4_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_4) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /*##-3- Start PWM signals generation #######################################*/ 
  /* Start channel 1 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 2 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start channel 3 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
  {
    /* PWM generation Error */
    Error_Handler();
  }
  /* Start channel 4 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_4) != HAL_OK)
  {
    /* PWM generation Error */
    Error_Handler();
  }

  while (1)
  {
  }

}

开发者ID:GreyCardinalRus，项目名称:stm32-cube，代码行数:101，代码来源:main.c

示例9: MX_TIM_Init

void MX_TIM_Init(void) {
  __HAL_RCC_TIM1_CLK_ENABLE();
  __HAL_RCC_TIM8_CLK_ENABLE();

  TIM_MasterConfigTypeDef sMasterConfig;
  TIM_OC_InitTypeDef sConfigOC;
  TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig;
  TIM_SlaveConfigTypeDef sTimConfig;

  htim_right.Instance               = RIGHT_TIM;
  htim_right.Init.Prescaler         = 0;
  htim_right.Init.CounterMode       = TIM_COUNTERMODE_CENTERALIGNED1;
  htim_right.Init.Period            = 64000000 / 2 / PWM_FREQ;
  htim_right.Init.ClockDivision     = TIM_CLOCKDIVISION_DIV1;
  htim_right.Init.RepetitionCounter = 0;
  htim_right.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
  HAL_TIM_PWM_Init(&htim_right);

  sMasterConfig.MasterOutputTrigger = TIM_TRGO_ENABLE;
  sMasterConfig.MasterSlaveMode     = TIM_MASTERSLAVEMODE_DISABLE;
  HAL_TIMEx_MasterConfigSynchronization(&htim_right, &sMasterConfig);

  sConfigOC.OCMode       = TIM_OCMODE_PWM1;
  sConfigOC.Pulse        = 0;
  sConfigOC.OCPolarity   = TIM_OCPOLARITY_HIGH;
  sConfigOC.OCNPolarity  = TIM_OCNPOLARITY_LOW;
  sConfigOC.OCFastMode   = TIM_OCFAST_DISABLE;
  sConfigOC.OCIdleState  = TIM_OCIDLESTATE_RESET;
  sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_SET;
  HAL_TIM_PWM_ConfigChannel(&htim_right, &sConfigOC, TIM_CHANNEL_1);
  HAL_TIM_PWM_ConfigChannel(&htim_right, &sConfigOC, TIM_CHANNEL_2);
  HAL_TIM_PWM_ConfigChannel(&htim_right, &sConfigOC, TIM_CHANNEL_3);

  sBreakDeadTimeConfig.OffStateRunMode  = TIM_OSSR_ENABLE;
  sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_ENABLE;
  sBreakDeadTimeConfig.LockLevel        = TIM_LOCKLEVEL_OFF;
  sBreakDeadTimeConfig.DeadTime         = DEAD_TIME;
  sBreakDeadTimeConfig.BreakState       = TIM_BREAK_DISABLE;
  sBreakDeadTimeConfig.BreakPolarity    = TIM_BREAKPOLARITY_LOW;
  sBreakDeadTimeConfig.AutomaticOutput  = TIM_AUTOMATICOUTPUT_DISABLE;
  HAL_TIMEx_ConfigBreakDeadTime(&htim_right, &sBreakDeadTimeConfig);

  htim_left.Instance               = LEFT_TIM;
  htim_left.Init.Prescaler         = 0;
  htim_left.Init.CounterMode       = TIM_COUNTERMODE_CENTERALIGNED1;
  htim_left.Init.Period            = 64000000 / 2 / PWM_FREQ;
  htim_left.Init.ClockDivision     = TIM_CLOCKDIVISION_DIV1;
  htim_left.Init.RepetitionCounter = 0;
  htim_left.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
  HAL_TIM_PWM_Init(&htim_left);

  sMasterConfig.MasterOutputTrigger = TIM_TRGO_UPDATE;
  sMasterConfig.MasterSlaveMode     = TIM_MASTERSLAVEMODE_ENABLE;
  HAL_TIMEx_MasterConfigSynchronization(&htim_left, &sMasterConfig);

  sTimConfig.InputTrigger = TIM_TS_ITR0;
  sTimConfig.SlaveMode    = TIM_SLAVEMODE_GATED;
  HAL_TIM_SlaveConfigSynchronization(&htim_left, &sTimConfig);

  sConfigOC.OCMode       = TIM_OCMODE_PWM1;
  sConfigOC.Pulse        = 0;
  sConfigOC.OCPolarity   = TIM_OCPOLARITY_HIGH;
  sConfigOC.OCNPolarity  = TIM_OCNPOLARITY_LOW;
  sConfigOC.OCFastMode   = TIM_OCFAST_DISABLE;
  sConfigOC.OCIdleState  = TIM_OCIDLESTATE_RESET;
  sConfigOC.OCNIdleState = TIM_OCNIDLESTATE_SET;
  HAL_TIM_PWM_ConfigChannel(&htim_left, &sConfigOC, TIM_CHANNEL_1);
  HAL_TIM_PWM_ConfigChannel(&htim_left, &sConfigOC, TIM_CHANNEL_2);
  HAL_TIM_PWM_ConfigChannel(&htim_left, &sConfigOC, TIM_CHANNEL_3);

  sBreakDeadTimeConfig.OffStateRunMode  = TIM_OSSR_ENABLE;
  sBreakDeadTimeConfig.OffStateIDLEMode = TIM_OSSI_ENABLE;
  sBreakDeadTimeConfig.LockLevel        = TIM_LOCKLEVEL_OFF;
  sBreakDeadTimeConfig.DeadTime         = DEAD_TIME;
  sBreakDeadTimeConfig.BreakState       = TIM_BREAK_DISABLE;
  sBreakDeadTimeConfig.BreakPolarity    = TIM_BREAKPOLARITY_LOW;
  sBreakDeadTimeConfig.AutomaticOutput  = TIM_AUTOMATICOUTPUT_DISABLE;
  HAL_TIMEx_ConfigBreakDeadTime(&htim_left, &sBreakDeadTimeConfig);

  LEFT_TIM->BDTR &= ~TIM_BDTR_MOE;
  RIGHT_TIM->BDTR &= ~TIM_BDTR_MOE;

  HAL_TIM_PWM_Start(&htim_left, TIM_CHANNEL_1);
  HAL_TIM_PWM_Start(&htim_left, TIM_CHANNEL_2);
  HAL_TIM_PWM_Start(&htim_left, TIM_CHANNEL_3);
  HAL_TIMEx_PWMN_Start(&htim_left, TIM_CHANNEL_1);
  HAL_TIMEx_PWMN_Start(&htim_left, TIM_CHANNEL_2);
  HAL_TIMEx_PWMN_Start(&htim_left, TIM_CHANNEL_3);

  HAL_TIM_PWM_Start(&htim_right, TIM_CHANNEL_1);
  HAL_TIM_PWM_Start(&htim_right, TIM_CHANNEL_2);
  HAL_TIM_PWM_Start(&htim_right, TIM_CHANNEL_3);
  HAL_TIMEx_PWMN_Start(&htim_right, TIM_CHANNEL_1);
  HAL_TIMEx_PWMN_Start(&htim_right, TIM_CHANNEL_2);
  HAL_TIMEx_PWMN_Start(&htim_right, TIM_CHANNEL_3);

  htim_left.Instance->RCR = 1;

  __HAL_TIM_ENABLE(&htim_right);
}

开发者ID:graybright，项目名称:hoverbase，代码行数:100，代码来源:setup.c

示例10: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 180 MHz */
  SystemClock_Config();
  
  /* Configure LED3 */
  BSP_LED_Init(LED3);  

  /*##-1- Configure the TIM peripheral #######################################*/ 
  /* -----------------------------------------------------------------------
    TIM1 Configuration: generate 1 PWM signal using the DMA burst mode:
  
    TIM1 input clock (TIM1CLK) is set to 2 * APB2 clock (PCLK2), 
    since APB2 prescaler is different from 1.   
      TIM1CLK = 2 * PCLK2  
      PCLK2 = HCLK / 2 
      => TIM1CLK = 2 * (HCLK / 2) = HCLK = SystemCoreClock
    
    To get TIM1 counter clock at 20 MHz, the prescaler is computed as follows:
      Prescaler = (TIM1CLK / TIM1 counter clock) - 1
      Prescaler = (SystemCoreClock /20 MHz) - 1
  
    The TIM1 Frequency = TIM1 counter clock/(ARR + 1)
                       = 20 MHz / 4096 = 4.88 KHz
    TIM1 Channel1 duty cycle = (TIM1_CCR1/ TIM1_ARR)* 100 = 33.33%
  
    Note: 
     SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f4xx.c file.
     Each time the core clock (HCLK) changes, user had to update SystemCoreClock 
     variable value. Otherwise, any configuration based on this variable will be incorrect.
     This variable is updated in three ways:
      1) by calling CMSIS function SystemCoreClockUpdate()
      2) by calling HAL API function HAL_RCC_GetSysClockFreq()
      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency  
  ----------------------------------------------------------------------- */
  
  TimHandle.Instance = TIMx;
  
  TimHandle.Init.Period            = 0xFFFF;
  TimHandle.Init.RepetitionCounter = 0;
  TimHandle.Init.Prescaler         = (uint16_t) ((SystemCoreClock / 20000000) - 1);
  TimHandle.Init.ClockDivision     = 0;
  TimHandle.Init.CounterMode       = TIM_COUNTERMODE_UP;
  if(HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /*##-2- Configure the PWM channel 3 ########################################*/ 
  sConfig.OCMode     = TIM_OCMODE_PWM1;
  sConfig.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfig.Pulse      = 0xFFF;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  
  /*##-3- Start PWM signal generation in DMA mode ############################*/ 
  if(  HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Starting PWM generation Error */
    Error_Handler();
  }
  
  /*##-4- Start DMA Burst transfer ###########################################*/ 
  HAL_TIM_DMABurst_WriteStart(&TimHandle, TIM_DMABASE_ARR, TIM_DMA_UPDATE,
                              (uint32_t*)aSRC_Buffer, TIM_DMABURSTLENGTH_3TRANSFERS);
  
  /* Infinite loop */
  while (1)
  {
  }
}

开发者ID:nidhiyanandh，项目名称:STM32Cube_FW_F4_V1.5.0_GCC_Makefile，代码行数:88，代码来源:main.c

示例11: xMotorStart

Status_t xMotorStart(TIM_HandleTypeDef* pxTIMHandle, MotorChannel_t xChannel)
{
  /*##- Start PWM signals generation #######################################*/
  switch(xChannel)
  {
  case MOTOR_CHANNEL_1:
    /* Start channel 1 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_1) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
  break;
  case MOTOR_CHANNEL_2:
    /* Start channel 2 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_2) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
  break;
  case MOTOR_CHANNEL_3:
    /* Start channel 3 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_3) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
  break;
  case MOTOR_CHANNEL_4:
    /* Start channel 4 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_4) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
  break;
  case MOTOR_CHANNEL_ALL:
    /* Start channel 1 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_1) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
    /* Start channel 2 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_2) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
    /* Start channel 3 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_3) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
    /* Start channel 4 */
    if(HAL_TIM_PWM_Start(pxTIMHandle, TIM_CHANNEL_4) != HAL_OK)
    {
      /* PWM Generation Error */
      return STATUS_ERROR;
    }
  break;

  default:
    return STATUS_ERROR;
  }
  /* Return OK */
  return STATUS_OK;
}

开发者ID:cjackie，项目名称:Quadcopter-Flight-Controller，代码行数:70，代码来源:Motor.c

示例12: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
 /* This sample code shows how to use STM32L0xx TIM HAL API to generate 4 PWM
  signals */
  
  /* STM32L0xx HAL library initialization:
       - Configure the Flash prefetch, Flash preread and Buffer caches
       - Systick timer is configured by default as source of time base, but user 
             can eventually implement his proper time base source (a general purpose 
             timer for example or other time source), keeping in mind that Time base 
             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
             handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock */
  SystemClock_Config();
  
  /* Compute the prescaler value to have TIM2 counter clock equal to 16 MHz */
  uwPrescalerValue = (SystemCoreClock / 16000000) - 1;

  
  /*##-1- Configure the TIM peripheral #######################################*/ 
  /* Initialize TIMx peripheral as follow:
       + Prescaler = (SystemCoreClock)/16000000
       + Period = 1600  (to have an output frequency equal to 10 KHz)
       + ClockDivision = 0
       + Counter direction = Up
  */
  TimHandle.Instance = TIM2;
  
  TimHandle.Init.Prescaler     = uwPrescalerValue;
  TimHandle.Init.Period        = PERIOD_VALUE;
  TimHandle.Init.ClockDivision = 0;
  TimHandle.Init.CounterMode   = TIM_COUNTERMODE_UP;
  if(HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
  {
    /* Initialization Error */
    ErrorHandler();
  }
  
  /*##-2- Configure the PWM channels #########################################*/ 
  /* Common configuration for all channels */
  sConfig.OCMode     = TIM_OCMODE_PWM1;
  sConfig.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfig.OCFastMode = TIM_OCFAST_DISABLE;

  /* Set the pulse value for channel 1 */
  sConfig.Pulse = PULSE1_VALUE;  
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Configuration Error */
    ErrorHandler();
  }
  
  /* Set the pulse value for channel 2 */
  sConfig.Pulse = PULSE2_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_2) != HAL_OK)
  {
    /* Configuration Error */
    ErrorHandler();
  }
  
  /* Set the pulse value for channel 3 */
  sConfig.Pulse = PULSE3_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_3) != HAL_OK)
  {
    /* Configuration Error */
    ErrorHandler();
  }
  
  /* Set the pulse value for channel 4 */
  sConfig.Pulse = PULSE4_VALUE;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_4) != HAL_OK)
  {
    /* Configuration Error */
    ErrorHandler();
  }
  
  /*##-3- Start PWM signals generation #######################################*/ 
  /* Start channel 1 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Starting Error */
    ErrorHandler();
  }
  /* Start channel 2 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
  {
    /* Starting Error */
    ErrorHandler();
  }
  /* Start channel 3 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
//.........这里部分代码省略.........

开发者ID:shjere，项目名称:common，代码行数:101，代码来源:main.c

示例13: BSP_Init

void BSP_Init(void) {
	RCC_OscInitTypeDef RCC_OscInitStruct;
	RCC_ClkInitTypeDef RCC_ClkInitStruct;

	__PWR_CLK_ENABLE()
	;

	__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

	RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
	RCC_OscInitStruct.HSEState = RCC_HSE_ON;
	RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
	RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
	RCC_OscInitStruct.PLL.PLLM = 8;
	RCC_OscInitStruct.PLL.PLLN = 336;
	RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
	RCC_OscInitStruct.PLL.PLLQ = 7;
	HAL_RCC_OscConfig(&RCC_OscInitStruct);

	RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
	RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
	RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
	RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
	RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
	HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);

	__GPIOB_CLK_ENABLE()
	;

	GPIO_InitTypeDef GPIO_Init;

	GPIO_Init.Mode = GPIO_MODE_AF_PP;
	GPIO_Init.Pull = GPIO_NOPULL;
	GPIO_Init.Speed = GPIO_SPEED_FAST;
	GPIO_Init.Alternate = GPIO_AF2_TIM3;
	GPIO_Init.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_4;
	HAL_GPIO_Init(LEDS_PORT, &GPIO_Init);


	__TIM3_CLK_ENABLE()
	;

	TIM_MasterConfigTypeDef TIM_MasterConfig;
	TIM_OC_InitTypeDef TIM_OC_Init;


	TIM3_Handle.Instance = TIM3;
	TIM3_Handle.Init.Prescaler = 84 - 1;

	TIM3_Handle.Init.CounterMode = TIM_COUNTERMODE_UP;
	TIM3_Handle.Init.Period = 1500;
	TIM3_Handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV2;
	HAL_TIM_PWM_Init(&TIM3_Handle);

	TIM_MasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
	TIM_MasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
	HAL_TIMEx_MasterConfigSynchronization(&TIM3_Handle, &TIM_MasterConfig);

	TIM_OC_Init.OCMode = TIM_OCMODE_PWM2;
	TIM_OC_Init.Pulse = 0;
	TIM_OC_Init.OCPolarity = TIM_OCPOLARITY_HIGH;
	TIM_OC_Init.OCFastMode = TIM_OCFAST_ENABLE;

	HAL_TIM_PWM_ConfigChannel(&TIM3_Handle, &TIM_OC_Init, TIM_CHANNEL_1);
	HAL_TIM_PWM_ConfigChannel(&TIM3_Handle, &TIM_OC_Init, TIM_CHANNEL_3);
	HAL_TIM_PWM_ConfigChannel(&TIM3_Handle, &TIM_OC_Init, TIM_CHANNEL_4);

	HAL_TIM_PWM_Start(&TIM3_Handle, TIM_CHANNEL_1);
	HAL_TIM_PWM_Start(&TIM3_Handle, TIM_CHANNEL_3);
	HAL_TIM_PWM_Start(&TIM3_Handle, TIM_CHANNEL_4);

	BSP_ADC_Init();
}

开发者ID:juanmanuellerda，项目名称:TPBlinky，代码行数:73，代码来源:bspTP1.c

示例14: main


//.........这里部分代码省略.........
  /* Compute the value to be set in ARR regiter to generate signal frequency at 8.78 Khz */
  TimerPeriod = (SystemCoreClock / 17570 ) - 1;
  /* Compute CCR1 value to generate a duty cycle at 50% for channel 1 */
  Channel1Pulse = (uint16_t) (((uint32_t) 5 * (TimerPeriod - 1)) / 10);
  /* Compute CCR2 value to generate a duty cycle at 37.5%  for channel 2 */
  Channel2Pulse = (uint16_t) (((uint32_t) 375 * (TimerPeriod - 1)) / 1000);
  /* Compute CCR3 value to generate a duty cycle at 25%  for channel 3 */
  Channel3Pulse = (uint16_t) (((uint32_t) 25 * (TimerPeriod - 1)) / 100);
  /* Compute CCR5 value to generate a duty cycle at 6.22%  for channel 5 (in PWM2)*/
  Channel5Pulse = (uint16_t) (((uint32_t) 622 * (TimerPeriod - 1)) / 10000);

  /* Initialize Timer TIM1 */  
  TimHandle.Instance = TIM1;
  TimHandle.Init.Prescaler         = 0;
  TimHandle.Init.Period            = TimerPeriod;
  TimHandle.Init.ClockDivision     = 0;
  TimHandle.Init.CounterMode       = TIM_COUNTERMODE_CENTERALIGNED1;
  TimHandle.Init.RepetitionCounter = 0;
  if(HAL_TIM_PWM_Init(&TimHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

  /*##-2- Configure the PWM channels #########################################*/ 
  /* Channels 1 configuration on TIM1 */
  sConfig.OCMode = TIM_OCMODE_PWM1;
  sConfig.Pulse = Channel1Pulse;
  sConfig.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfig.OCNPolarity = TIM_OCNPOLARITY_HIGH;
  sConfig.OCFastMode = TIM_OCFAST_DISABLE;
  sConfig.OCIdleState = TIM_OCIDLESTATE_RESET;
  sConfig.OCNIdleState = TIM_OCNIDLESTATE_RESET;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_1) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  /* Channels 2 configuration on TIM1 */
  sConfig.Pulse = Channel2Pulse;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_2) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  /* Channels 3 configuration on TIM1 */
  sConfig.Pulse = Channel3Pulse;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_3) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }
  /* Channels 5 configuration on TIM1 */
  sConfig.OCMode = TIM_OCMODE_PWM2;
  sConfig.Pulse = Channel5Pulse;
  if(HAL_TIM_PWM_ConfigChannel(&TimHandle, &sConfig, TIM_CHANNEL_5) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }

  /*##-3- Group channel 5 and channels 1, 2 and 3 ############################*/ 
  if(HAL_TIMEx_GroupChannel5(&TimHandle, (TIM_GROUPCH5_OC1REFC |\
                                          TIM_GROUPCH5_OC2REFC |\
                                          TIM_GROUPCH5_OC3REFC)) != HAL_OK)
  {
    /* Configuration Error */
    Error_Handler();
  }

  /*##-4- Start PWM signals generation #######################################*/ 
  /* Start TIM1 channel 1 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_1) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start TIM1 channel 2 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_2) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start TIM1 channel 3 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_3) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }
  /* Start TIM1 channel 5 */
  if(HAL_TIM_PWM_Start(&TimHandle, TIM_CHANNEL_5) != HAL_OK)
  {
    /* PWM Generation Error */
    Error_Handler();
  }

  while (1)
  {
  }
}

开发者ID:PaxInstruments，项目名称:STM32CubeF3，代码行数:101，代码来源:main.c

示例15: Motors_init

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ HAL_TIM_ReadCapturedValue函数代码示例发布时间：2022-05-30

C++ HAL_TIM_PWM_Init函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：19212|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9994|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8331|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8699|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8642|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9663|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8627|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：8003|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8660|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7537|2022-11-06

客服电话

电子邮件

C++ HAL_TIM_PWM_Start函数代码示例

示例1: main

示例2: main

示例3: main

示例4: HAL_SYSTICK_Callback

示例5: MOTOR_Init

示例6: main

示例7: pwmout_write

示例8: main

示例9: MX_TIM_Init

示例10: main

示例11: xMotorStart

示例12: main

示例13: BSP_Init

示例14: main

示例15: Motors_init

请发表评论

全部评论

上一篇：

下一篇：

相机标定过程(opencv) + matlab参数导入ope

ashchan/mail-notifr: Mail Notifr - Gmail

TwistedAsylumMC/bedrock-unicode-characte

uber/RIBs: Uber's cross-platform mob

ajtowf/ng2_play: Angular 2 Play with Mat

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053

客服电话

电子邮件

C++ HAL_TIM_PWM_Start函数代码示例

示例1: main

示例2: main

示例3: main

示例4: HAL_SYSTICK_Callback

示例5: MOTOR_Init

示例6: main

示例7: pwmout_write

示例8: main

示例9: MX_TIM_Init

示例10: main

示例11: xMotorStart

示例12: main

示例13: BSP_Init

示例14: main

示例15: Motors_init

请发表评论

全部评论

上一篇：

下一篇：

相机标定过程(opencv) + matlab参数导入ope

ashchan/mail-notifr: Mail Notifr - Gmail

TwistedAsylumMC/bedrock-unicode-characte

uber/RIBs: Uber&#39;s cross-platform mob

ajtowf/ng2_play: Angular 2 Play with Mat

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053

uber/RIBs: Uber's cross-platform mob